Search NASA⌕ Search

SEARCH · Search NASA

Results for “pallets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

Data requirements for verification of ram glow chemistry

A set of questions is posed regarding the surface chemistry producing the ram glow on the space shuttle. The questions surround verification of the chemical cycle involved in the physical processes leading to the glow. The questions, and a matrix of measurements required for most answers, are presented. The measurements include knowledge of the flux composition to and from a ram surface as well as spectroscopic signatures from the U to visible to IR. A pallet set of experiments proposed to accomplish the measurements is discussed. An interim experiment involving an available infrared instrument to be operated from the shuttle Orbiter cabin is also be discussed.

Swenson, G. R.↗

Radiation mapping on Spacelab 1: Experiment no. INS006

The first attempt at mapping the radiation environment inside Spacelab is described. Measurements were made by a set of passive radiation detectors distributed throughout the volume inside the Spacelab 1 module, in the access tunnel and outside on the pallet. Measurements of the low linear energy transfer (LET) component obtained from the TLD thermoluminescent detectors (TLD) ranged from 92 to 134 mrad, yielding an average low LET dose rate of 10.0 mrads/day inside the module. Because of the higher inclination orbit, substantial fluxes of highly ionizing (HZE particles) high charge and energy galactic cosmic rays were observed for the first time on an STS flight, yielding an overall average mission dose-equivalent of 295 mrem, or 29.5 mrem/day, which is about three times higher than that measured on previous STS missions. Little correlation is found between measured average dose rates or HZE fluences and the estimates shielding throughout the volume of the module.

Benton, E. V.↗

CID-720 aircraft high-environment flight instrumentation system

The high-environment flight instrumentation system was designed to acquire Langley's structural response data during the full scale transport-controlled impact demonstration test. There was only one opportunity for data acquisition. Thus, a high reliability and crashworthy design approach was implemented. The approach featured multi-level redundancy and a vigorous quality assurance testing program. Complying with an accelerated schedule, the instrumentation system was developed, tested and shipped within 18 months to Dryden Flight Research Facility. The flight instrumentation system consists of two autonomous data systems, DAS #1 and #2, and an excellent checkout subsystem. Each data system is partitioned into four pallets. The system was designed to operate on manned and unmanned flights. There are 176 data channels per data system. These channels are sequentially sampled and encoded into 1 megabit/sec pulse code modulation (PCM) data signal. To increase the probability of success, a special PCM distribution subsystem was developed. This subsystem distributes the PCM signal to two transmitters, one delay memory, and eight recorder tracks. The data on four of these trackes was digitally delayed approximately 300 msec to maximize data acquisition during impact. Therefore each data system's data is redundantly recorded onboard and on the ground. There are two time code generators. Parallel time from each is encoded into both data systems. Serial time from each is redundantly recorded on both onboard recorders. Instrumentation power is independent of aircraft power and self-contained.

Calloway, R. S.↗

CID-720 aircraft Langley Research Center preflight hardware tests: Development, flight acceptance and qualification

The testing conducted on LaRC-developed hardware for the controlled impact demonstration transport aircraft is discussed. To properly develop flight qualified crash systems, two environments were considered: the aircraft flight environment with the focus on vibration and temperature effects, and the crash environment with the long pulse shock effects. Also with the large quantity of fuel in the wing tanks the possibility of fire was considered to be a threat to data retrieval and thus fire tests were included in the development test process. The aircraft test successfully demonstrated the performance of the LaRC developed heat shields. Good telemetered data (S-band) was received during the impact and slide-out phase, and even after the aircraft came to rest. The two onboard DAS tape recorders were protected from the intense fire and high quality tape data was recovered. The complete photographic system performed as planned throughout the 40.0 sec of film supply. The four photo power distribution pallets remained in good condition and all ten onboard 16 mm high speed (400 frames/sec) cameras produced good film data.

Pride, J. D.↗

The Imaging Spectrometric Observatory

Design and performance features of the Imaging Spectrometric Observatory (ISO) first flown on Spacelab 1 for atmospheric, earth surface and stellar monitoring are outlined. The ISO has five grating spectrometers fitted with CCD arrays for simultaneously gathering spectral and spatial data. The instrument covered the 300-12,700 A range on the Spacelab 1 flight, when it was mounted on a pallet and used for atmospheric scans at high solar zenith angles. A future mission is planned which will include limb-viewing of OH, NO, ClO and NO2 radicals in the middle atmosphere to complement the data collected in the Upper Atmosphere Research Satellite program. Technical details are presented of the instrument components and ground- and balloon-borne test results.

Torr, D. G.↗

Radiation environment of Spacelab-1

The results of passive and active radiation measurements on Spacelab-1 are reported. Spacelab-1 was flown on the STS-9 mission, orbited at an altitude of 241 km, with an inclination of 57 deg and 240 hours of flight time. Approximately thirty passive detectors deployed inside the module, in the access tunnel, and outside on the pallet made possible the radiation measurements. The various forms of radiation measured were a low linear energy transfer component ranging from 94 to 133 mrads inside the module (average dose rate of 10.0 mrads/day; about twice the rate of earlier shuttle flights), an average mission dose-equivalent rate of about 18.5 mrem/day (six times higher than earlier flights), accumulated doses of 125 and 128 mrads and a yield of 17 and 12 mrads for passages through the South Atlantic Anomaly. Spacelab-1, because of its low altitude and short duration, was relatively benign in terms of total radiation dose. Some of the measurements such as high-LET particles and neutrons have biological significance and potential effects on future experiments.

Benton, E. V.↗

Development status of first Tethered Satellite System

An MOU between NASA and Italian research organizations has assigned the responsibilities for the development, payload integration, launch and operation of a Tethered Satellite System (TSS). The TSS will include a deployer mounted on a Spacelab pallet, science equipment on a customized mission support structure and a satellite connected to the Orbiter by a tether. The satellite is 1.6 m in diameter and can weight up to 500 kg. The deployer will be insulated from the Orbiter because of the conductive nature of the tether. The first mission is to demonstrate the TSS technology, perform electrodynamic investigations of the interaction of the tether with ambient space plasma, and gather data on atmospheric interactions in the lower thermosphere, geomagnetic phenomena and gravimetric characteristics. The first TSS will be deployed 20 km outward from the Orbiter and the earth on a strand of tin-coated copper wire wrapped in Teflon insulation, braided Kevlar and a Nomek jacket. The first strand is designed to accommodate 53 N tension. The satellite on the end of the tether will be a multimission platform for facile changeout of the scientific package from mission-to-mission.

Sisson, J. M.↗

The X-SAR System

During the past few years, there has been significant progress made in the planning for an X-band SAR, designed to fly in the shuttle together with the SIR-C system of NASA/JPL. New work and studies have been initiated to enable the goal of two missions in 1990 to be met. The antennas of X-SAR and SIR-C will be placed side-by-side on a pivoted steerable foldable structure, which will allow antenna movement without changing the attitude of the shuttle. This figure also shows the pallet, underneath the antenna structure, which houses the electronic sub-systems of both radars. Although the two radar systems, X-band SAR and the L- and C-band SAR of SIR-C, have different technical designs, their overall system performance, in terms of image quality, is expected to be similar. The current predicted performance of the X-SAR system based on results of the continuing Phase B studies is detailed. Differences between the performance parameters of X-SAR and those of SIR-C are only detailed in as far as they affect planning decisions to be made by experimenters.

Oettl, Herwig↗

Results from the vehicle charging and potential experiment on STS-3

The Vehicle Charging and Potential Experiment formed part of the scientific experiments comprising the NASA Office of Space Sciences-1 pallet flown at an altitude of 250 km and an orbital inclination of 40 deg on the third flight of the Space Shuttle Orbiter in March 1982. Details of the objectives, the instrumentation of the experiment, and some preliminary results from the individual instruments are presented. The experiment studied passive vehicle charging using thermal plasma probes, and it is concluded that apart from moderate v x B (L)-induced electrical potential resulting from the large size and restricted plasma contact area, the Space Shuttle Orbiter behaved similarly to smaller spacecraft orbiting in the same ionospheric region. However, an unexpected passive orbital result was the detection of enhanced plasma density in the vicinity of the Orbiter under restricted orbital conditions, apparently composed of contaminant molecular species and with an electron component having a temperature considerably higher than the ambient ionosphere electrons. The active vehicle charging experiments were performed by using a 100 mA/1 keV electron beam emitted out of the payload bay. Charging measurements made during short electron beam pulse emissions provide an upper limit of about 1 mF for the Orbiter capacitance. Steady-state charging measurements showed that for the vehicle attitudes covered by the mission, the induced electrical potential was normally only a few volts, except during some nighttime conditions when it rose above 40 V.

Banks, P. M.↗

Thermal control of the Lidar In-Space Technology Experiment

The Lidar In-Space Technology Experiment (LITE) will employ lidar techniques to study the atmosphere from space. The LITE instrument will be flown in the Space Shuttle Payload Bay with an earth directed orientation. The experiment thermal control incorporates both active and passive techniques. The Laser Transmitter Module (LTM) and the system electronics will be actively cooled through the Shuttle pallet coolant loop. The receiver system and experiment platform will be passsively controlled through the use of insulation and component surface properties. This paper explains the thermal control techniques used and the analysis results, with primary focus on the receiver system.

Carlson, Ann B.↗

Space-based test-bed concept

The space test-bed (STB) conceptual design proposed as a basis for the long-term experimental development of advanced spacecraft bus technology with minimum technological risk consists of a main spacecraft bus, whose subsystems furnish the common support functions for the entire facility, and attachable/detachable experimental pallets. The STB design requires only modest enhancements of current systems and techniques, with many off-the-shelf components. The economics of the STB are presently emphasized.

Gartrell, Charles F.↗

New test techniques to evaluate near field effects for supersonic store carriage and separation

Store separation and store carriage drag studies were conducted. A primary purpose is to develop new experimental methods to evaluate near field effects of store separation and levels of store carriage drag associated with a variety of carriage techniques for different store shapes and arrangements. Flow field measurements consisting of surface pressure distributions and vapor screen photographs are used to analyze the variations of the store separation characteristics with cavity geometry. Store carriage drag measurements representative of tangent, semi-submerged, and internal carriage installations are presented and discussed. Results are included from both fully metric models and models with only metric segments (metric pallets) and the relative merits of the two are discussed. Carriage drag measurements for store installations on an aircraft parent body are compared both with prediction methods and with installations on a generic parent body.

Sawyer, Wallace C.↗

Retrievable Payload Carrier (RPC): Next generation Long Duration Exposure Facility

The Retrievable Payload Carrier (RPC) is described which is a multi-experiment, free-flyer spacecraft being privately developed to make in-space experimentation more accessible and economically feasible for research and development organizations. The carrier concept was derived from NASA's highly successful and flight proven Long Duration Exposure Facility (LDEF). The LDEF capabilities were enhanced to meet new customer requirements. This reusable payload carrier is planned for launch and retrieval by the space shuttle on a regular basis. The RPC's compact design facilitates flexible manifesting of the shuttle cargo bay space, thereby, permitting timely launches and retrievals. The vehicle is designed so that either the entire carrier can be retrieved from orbit, or individual experiment pallets can be removed and replaced in orbit. This gives customers even greater control over their experiment recoveries. A fully operational RPC System consists of: (1) a carrier spacecraft; (2) a ground control station for communication with customer payloads and the carrier; (3) a ground processing facility to provide refurbishment, final checkout, and integration of customer payloads and the carrier; and (4) the personnel required to support both the development and operation phases of the program. Customer payloads will fly 6 to 18 month missions, or longer, as required. Spreading launch, operations, and retrieval costs over multiple experimental payloads results in minimized customer costs. The RPC Program's initial objective is to operate a simple carrier system which meets basic customer service needs.

Perry, Arthur T.↗

A pointable, helicopter-based remote sensing data acquisition system for collecting bidirectional reflectance data

Discussed here is a new configuration of a helicopter-borne remote sensing system to support field measurements programs such as studies of forest decline damage associated with atmospheric deposition and the Forest Ecosystems Dynamics project. In this new configuration, the sensor payload is mounted externally on a hinged pallet located on the starboard side of the Bell Iroquois UH-1B (HUEY) helicopter. The sensor payload includes a set of bore-sighted instruments consisting of a Barnes Modular Multiband Radiometer (MMR), a Spectron Engineering (SE) 590 spectroradiometer, an Everest infrared temperature sensor, and a Sony CCD video camera with a 10x zoom lens. The system was tested and excellent data was acquired in 1990.

Williams, Darrel L.↗

Laser Welding in Space

Solidification type welding process experiments in conditions of microgravity were performed. The role of convection in such phenomena was examined and convective effects in the small volumes obtained in the laser weld zone were observed. Heat transfer within the weld was affected by acceleration level as indicated by the resulting microstructure changes in low gravity. All experiments were performed such that both high and low gravity welds occurred along the same weld beam, allowing the effects of gravity alone to be examined. Results indicate that laser welding in a space environment is feasible and can be safely performed IVA or EVA. Development of the hardware to perform the experiment in a Hitchhiker-g platform is recomended as the next step. This experiment provides NASA with a capable technology for welding needs in space. The resources required to perform this experiment aboard a Shuttle Hitchhiker-pallet are assessed. Over the four year period 1991 to 1994, it is recommended that the task will require 13.6 manyears and $914,900. In addition to demonstrating the technology and ferreting out the problems encountered, it is suggested that NASA will also have a useful laser materials processing facility for working with both the scientific and the engineering aspects of materials processing in space. Several concepts are also included for long-term optimization of available solar power through solar pumping solid state lasers directly for welding power.

Workman, Gary L.↗

Tethered Satellite System Tip Canister - Thermal design and test

The Tethered Satellite System (TSS) is scheduled for launch, on STS-46 in mid-1992. The major mission objective is to investigate electrodynamic phenomena associated with long electrically conductive tether, in the earth orbital environment. A spherical Satellite (1.6-m diameter), remains connected to the Orbiter throughout TSS-1 mission by a conductive tether. The Satellite operates at up to 20 km above the Orbiter during the TSS mission. The Tip Canister (TPC), that is mounted on the end of a 12-m retractable boom, contains mechanisms that control and monitor tether movement. The TPC is an independent thermal system from the base 'Deployer/Spacelab Pallet'. This paper presents the TPC thermal design verification approach that includes a description of thermal design and thermal balance testing. Flight TPC temperature predictions are also presented.

Chapter, John J.↗

Shuttle and Space Station scientific payloads - Their role in the next generation

Scientific payloads that will be flown aboard the Space Shuttle in the next era of flight operations as well as Space Station's major payload initiatives are reviewed. In particular, attention is given to Spacelab payloads, pallet payloads, Mission Peculiar Equipment Support Structures missions, and retrieval payloads. Other payloads discussed are related to industrial research, astronomical studies, upper atmosphere, and Space Station operations.

Schuiling, R. L.↗

Extended Duration Orbiter - Meeting the challenge

The paper overviews the Extended Duration Orbiter (EDO) program designed to provide an on-orbit stay capability of 16 days using the Orbiter Vehicle OV-102. Special attention is given to the EDO's subsystems and substructures, including the cryogenic pallet, the cryogenic storage tanks, the cryogenic solenoid valves, the regenerable carbon dioxide removal system, and the waste collection system. The EDO program will start with the STS-50 U.S. Microgravity Lab mission planned for June 1992.

Saucier, D. R.↗