Results for “particle fracture” — Page 13

DOE OSTI2021

Synthesis and Morphological Characterization of Electroless-Deposited Ni-P Coatings on Diamond Abrasives

Deposition of a coating on rough surfaces faces unique challenges due to the complexity of substrate morphology. In the present research, electroless deposition of a Ni-P coating was successfully deposited on diamond particles. Microtomography was conducted to study the deposition mechanisms. It revealed that the coating coverage rate on diamond particles was affected by the synergistic action of the deposition time, substrate morphology, and hypophosphite concentration. The best coverage was achieved in a solution with 0.2 mol/L hypophosphite. Two major morphological features of the coating: nodular and smooth, were influenced by the deposition parameters, coating integrity, and substrate morphology. The failure was seen in fractured and peeled off coatings. It was due to residual stress produced by the coalescing of crystallites during the deposition. This failure mechanism explains the tendency of coating fracture at three morphological features of the substrate. This work is beneficial to semiconductor manufacturing where effective cutting in chip fabrication is essential.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Statistical mechanical model for crack growth

Analytic relations that describe crack growth are vital for modeling experiments and building a theoretical understanding of fracture. Upon constructing an idealized model system for the crack and applying the principles of statistical thermodynamics, it is possible to formulate the rate of thermally activated crack growth as a function of load, but the result is analytically intractable. In this report an asymptotically correct theory is used to obtain analytic approximations of the crack growth rate from the fundamental theoretical formulation. These crack growth rate relations are compared to those that exist in the literature and are validated with respect to Monte Carlo calculations and experiments. The success of this approach is encouraging for future modeling endeavors that might consider more complicated fracture mechanisms, such as inhomogeneity or a reactive environment.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Complete Development of Critical Capabilities for TRISO Fission Product Source Term Calculations and Quantify Mechanisms for Pd Penetration of SiC

Overall fission product (FP) release will be an important consideration for the licensing and deployment of advanced reactors utilizing tristructural isotropic (TRISO) fuels. This work focuses on enhancing and applying the BISON models needed to predict FP transport within TRISO particles and particle failure probability, both of which factor directly into release predictions. Specifically, this report details (1) the development of the models needed to predict palladium (Pd) conservation at the engineering scale and the application of those models to characterize Pd fluxes for input into a mechanistic multiscale model for Pd penetration; (2) the refinement of sorption mass transfer models and the development of models for trapping in porous layers, which were applied and compared to particle scans from AGR-2 to provide proof of concept for a method of particle-scale validation that may reduce uncertainties compared to compact-scale validation using data from integral effects tests; (3) the development of a failure-statistics-informed, mesh-independent methodology for applying smeared cracking, enabling further study of the localized multiphysics behaviors associated with cascading particle failure mechanisms; and (4) the preliminary characterization of those coupled multiphysics particle failure behaviors using smeared, nonretentive diffusivities to provide a baseline for future study and to guide ongoing engineering applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Structural and mechanical properties of magnesium aluminate nanoceramics under high pressure

Nanoceramics may have different structural and physical properties compared to their coarse-grained counterparts. Here, we report the high-pressure study of micro- and nano-crystalline MgAl2O4 in order to examine the effect of particle size on the structural stability. A reversible pressure-induced phase transition (cubic to tetragonal) is observed in MgAl2O4 nanocrystals under non-hydrostatic pressure at room temperature, in contrast to the previously reported structural transition of MgAl2O4 at high pressure and high temperature. It is also found that the compressed MgAl2O4 microcrystals do not fracture further below 60 nm, suggesting a plastic deformation mechanism transition. MgAl2O4 with a grain size above ∼60 nm exhibits normal cracking behaviors, but shows metal-like plastic deformation behaviors below this critical size. It is implied that combined ductility and strength can be achieved in nanoceramic MgAl2O4.

Xu, Jianing (ORCID:0000000325474344)↗

DOE OSTI2025

Modelling the brittle failure of graphite induced by the controlled impact of runaway electrons in DIII-D

The thermo-mechanical response of an ATJ graphite sample to controlled runaway electron (RE) dissipation, realized in DIII-D, is modelled with a novel work-flow that features the RE orbit code KORC, the Monte Carlo particle transport code Geant4 and the finite element multiphysics software COMSOL. KORC provides the RE striking positions and momenta, Geant4 calculates the volumetric energy deposition and COMSOL simulates the thermoelastic response. Brittle failure is predicted according to the maximum normal stress criterion, which is suitable for ATJ graphite owing to its linear elastic behavior up to fracture and its isotropic mechanical properties. Measurements of the conducted energy, damage topology, explosion timing and blown-off material volume, impose a number of empirical constraints that suffice to distinguish between different RE impact scenarios and to identify RE parameters which provide the best match to the observations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Simulation and analysis of the 3D double shock-induced recompression of spall using a hybrid PAGOSA with FLIP+MPM

In this work, an innovative hybrid algorithm PAGOSA with FLIP + MPM is first presented by coupling PAGOSA with the particle FLIP + MPM, and applied to systematically exploring the 3D recompression of spall induced by double-shock waves in ductile materials as the few existing studies are currently limited to the pure longitudinal recompression of spall, and ignore the 3D effects. This algorithm solves the difficulties the grid-based methods encounter when applied to capturing the fracture in material. We first validate the capabilities of PAGOSA with FLIP + MPM to predict different fracture/fragmentation cases by solving two benchmark problems and comparing with the analytical solutions or the experiment results. The convergences and the infinity-norm errors are also investigated. Subsequently, the 3D effects are demonstrated by simulating the spallation in material using PAGOSA with FLIP + MPM and comparing with those in the longitudinal cases. Additionally, some factors that affect the spallation with 3D effects are also discussed. Finally, the recompressions of spall in material with/without 3D effects are systematically simulated and analyzed. The recompression of spall driven by a high explosive is also simulated to show the ability of PAGOSA with FLIP + MPM to handle this kind of problem. The conditions that can lead to a recompression of spall are explored. Also, numerical results show that PAGOSA with FLIP + MPM can accurately predict different fracture cases, that the 3D effects play an important role in fracture/fragmentation, and the recompression of spall is very sensitive to the occurrence conditions, shows great differences when considering 3D effects in real applications. Moreover, the present hybrid method can be easily extended to other grid-based techniques employed for fracture in materials.

3D effects↗

DOE OSTI2026

Small-𝑥 Factorization in the Target Fragmentation Region

We consider the differential cross-section for single-inclusive jet production with transverse momentum 𝑃 ⊥ in deep inelastic scattering at small Bjorken 𝑥 Bj , mediated by a virtual photon with virtuality 𝑄 2 . Unlike most studies at small 𝑥, which focus on particle production in the current fragmentation region, we investigate the kinematic regime where the jet is produced in the target fragmentation hemisphere of the Breit frame, and with 𝑃 ⊥ ≪ 𝑄. For a longitudinally polarized photon, we demonstrate that this cross section is not power suppressed in 𝑃 ⊥ /𝑄 and we derive a factorized expression in terms of extended quark and gluon jet fracture functions. Our formula, valid at next-to-leading order in 𝛼 𝑠 at small 𝑥, is akin to the Altarelli-Martinelli identity for the longitudinal DIS structure function. Numerical estimates show that the extended quark jet fracture function is the most sensitive to saturation effects in large nuclei.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2020

A scale-invariant bonded particle model for simulating large deformation and failure of continua

In this paper, a scale-invariant bond model for simulating two-dimensional large deformation of continua is presented. An accurate torque form caused by relative rotation between bonded particles is derived based on beam theory. Validations of the proposed bond model are carried out by large deformation simulations of a simply supported beam subjected to central loading and a cantilever beam with end loading. Comparison of simulations with analytical solutions show a very good agreement. Later, Brazilian tests are simulated to demonstrate the ability of the framework to model failure and fracture process of rock.

58 GEOSCIENCES↗

DOE OSTI2026

Emergence of Diverse Failure Patterns in Weathering‐Induced Landslides: Insights From Particle Finite Element Simulations

Weathering is a fundamental driver of landslide evolution over geological timescales. Despite its ubiquity and importance, quantifying how weathering drives the progressive destabilization of rock slopes remains challenging. In this work, we develop a unified computational framework based on the particle finite element method to investigate the evolution of weathering‐induced landslides, from long‐term weathering to short‐term slope failure and runout dynamics. The framework integrates key processes, including weathering front propagation, time‐dependent strength degradation, rupture surface development, and post‐failure runout dynamics. Through numerical simulation experiments, we elucidate how interactions among weathering characteristics (type, intensity, and rate law), bedrock strength, fracture distribution, and slope geometry govern the failure modes and kinematics of weathering‐induced landslides. Simulations show that matrix‐dominated weathering leads to shallow translational failures, whereas fracture‐dominated weathering produces deep‐seated rotational and compound landslides. Pre‐existing fractures and slope morphology also strongly influence the movement of destabilized landmasses, affecting the failure pattern (e.g., kinematic mode and rupture surface geometry) and post‐failure behavior (e.g., runout velocity). We further demonstrate that the failure time and volume of weathered slopes are governed by the competition between gravitational driving forces and cohesive resisting forces during progressive destabilization. These findings provide new insights into the fundamental mechanisms that drive the emergence of diverse failure patterns of weathering‐induced landslides with important implications for landslide hazard assessment.

Wang, Liang [Eidgenoessische Technische Hochschule↗

DOE OSTI2022

High Performance Circuit Pastes for Solid Oxide Fuel Cell Applications: Final Technical Report

Using a combination of in-plane electrical conductivity measurements, electrical contact resistance measurements, tensile fracture tests, double shear lap fracture tests, rapid thermal cycling adhesion tests, in situ wetting angle measurements, 3D X-ray tomography, reduction-oxidation (RedOx) cycling, scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDAX), Density Functional Theory (DFT) modeling, Molecular Dynamics (MD) modeling, and Phase Field modeling, this project determined that a new brazing technique developed by the PIs (specifically the use of nickel particles to direct the wetting and spreading of molten silver) could be used to produce well-adhered, >97% dense, electrically-conductive circuits, current collectors, and/or electrical contacts on a variety of ceramic and ceramic-coated substrates (specifically lanthanum strontium manganite, yttria stabilized zirconia, sapphire, Cr2O3-passivated stainless steel, and Al2O3-passivated stainless steel). Compared to other silver-based alternatives, Ag:Ni led to less manufacturing defects and was more tolerant of the extreme environments (isothermal high-temperature aging) and occasional abuse (rapid thermal cycling and RedOx cycling) encountered during Solid Oxide Fuel Cell and/or Solid Oxide Electrolysis Cell operation. Further, in some situations (such as when to produce Ag:Ni electrical contacts to Al2O3-protected stainless steel) the Ni particles also improved operation by acting as chemical getters that removed electrically-insulating, surface-segregating substrate impurities (i.e. by lowering the contact resistance with the underlying substrate).

36 MATERIALS SCIENCE↗

DOE OSTI2019

Initial Simulations of Empty Room Collapse and Reconsolidation at the Waste Isolation Pilot Plant

The Waste Isolation Pilot Plant (WIPP) is a geologic repository for defense-related nuclear waste. If left undisturbed, the virtually impermeable rock salt surrounding the repository will isolate the nuclear waste from the biosphere. If humans accidentally intrude into the repository in the future, then the likelihood of a radionuclide release to the biosphere will depend significantly on the porosity and permeability of the repository itself. Room ceilings and walls at the WIPP tend to collapse over time, causing rubble piles to form on floors of empty rooms. The surrounding rock formation will gradually compact these rubble piles until they eventually become solid salt, but the length of time for a rubble pile to reach a certain porosity and permeability is unknown. This report details the first efforts to build models to predict the porosity and permeability evolution of an empty room as it closes. Conventional geomechanical numerical methods would struggle to model empty room collapse and rubble pile consolidation, so three different meshless methods, the Immersed Isogeometric Analysis Meshfree, Reproducing Kernel Particle Method (RKPM), and the Conformal Reproducing Kernel method, were assessed. First, the meshless methods and the finite element method each simulated gradual room closure, without ceiling or wall collapse. All three methods produced equivalent room closure predictions with comparable computational speed. Second, the Immersed Isogeometric Analysis Meshfree method and RKPM simulated two-dimensional empty room collapse and rubble pile consolidation. Both methods successfully simulated large viscoplastic deformations, fracture, and rubble pile rearrangement to produce qualitatively realistic results. In addition to geomechanical simulations, the flow channels in damaged salt and crushed salt were measured using micro-computed tomography, and input into a computational fluid dynamics simulation to predict the salt's permeability. Although room for improvement exists, the current simulation approaches appear promising.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Novel processing route for design and manufacturing of metal toughened nanoceramics: Al–Al 2 O 3 nanocermets

Monolithic alumina is a highly brittle ceramic with a very low fracture toughness, making it an unreliable material for mechanical and structural applications. Ceramic-metal composites (cermets) are the subject of intensive interest to obtain materials which can address the intrinsic brittleness of ceramics without compromising their high strength and light weight. In the present investigation, aluminium-alumina (Al–Al 2 O 3 ) nanocermets were developed. The nanocermets possessed the toughness of Al phase and the strength of reinforced nano Al 2 O 3 particles. Here, the nanocermets green bodies were prepared such that upon sintering each adjacent Al 2 O 3 grain was conformally coated with a continuous Al film. Mechanical milling via a combination of cryo-milling and ball-milling was used to prepare Al–Al 2 O 3 nano-powder mixture. Spark plasma sintering was used to consolidate the green nanocermets. Results show that specimens prepared from 35 h milled powders exhibited superior mechanical properties as compared to other nanocermets, with an improvement in microhardness, elastic modulus, compressive strength, and flexural strength by 88%, 78%, 69% and 40% with respect to sintered pure Al. The indentation toughness of 35 h milled nanocermet showed an increment of 12.5% with respect to sintered pure Al 2 O 3 . Characterization techniques such as XRD, SEM, HR-TEM, X-ray tomography were employed to investigate the phase evolution and structural morphology, while FEM simulations were performed for understanding the crack propagation mechanisms in nanocermets.

36 MATERIALS SCIENCE↗

DOE OSTI2022

The effect of differential mineral shrinkage on crack formation and network geometry

Rock, concrete, and other engineered materials are often composed of several minerals that change volumetrically in response to variations in the moisture content of the local environment. Such differential shrinkage is caused by varying shrinkage rates between mineral compositions during dehydration. Using both 3D X-ray imaging of geo-architected samples and peridynamic (PD) numerical simulations, we show that the spatial distribution of the clay affects the crack network geometry with distributed clay particles yielding the most complex crack networks and percent damage (99.56%), along with a 60% reduction in material strength. We also demonstrate that crack formation, growth, coalescence, and distribution during dehydration, are controlled by the differential shrinkage rates between a highly shrinkable clay and a homogeneous mortar matrix. Sensitivity tests performed with the PD models show a clay shrinkage parameter of 0.4 yields considerable damage, and reductions in the parameter can result in a significant reduction in fracturing and an increase in material strength. Additionally, isolated clay inclusions induced localized fracturing predominantly due to debonding between the clay and matrix. These insights indicate differential shrinkage is a source of potential failure in natural and engineered barriers used to sequester anthropogenic waste.

58 GEOSCIENCES↗

DOE OSTI2025

Discrete fracture network model benchmarks developed and applied in a DECOVALEX-2023 repository performance assessment study

This study presents newly developed benchmarks for modeling flow and transport within discrete fracture networks (DFNs) and useful methods for analyzing the results. The new benchmarks are designed to test modeling approaches for use in probabilistic performance assessment models of deep geologic repositories in fractured rock. The benchmarks simulate flow and transport through a 1 km 3 block of fractured rock. The first simulates migration of a short pulse of tracer through a simple network of four intersecting fractures. The second adds 1089 stochastically generated fractures. The third changes the pulse to a continuous point source. Evaluation of model performance relies on moment analysis and comparison of the results of different models. The expected nondimensional first moment of the conservative tracer for each benchmark is 1. The benchmarks were simulated by teams from Canada, Czechia, Germany, Korea, Sweden, Taiwan, and the United States as part of a DECOVALEX-2023 study (decovalex.org). The teams used various approaches, including explicit DFN modeling, DFN upscaling to an equivalent continuous porous medium (ECPM), and a combination of both methods. Transport mechanisms are modeled using either the advection-dispersion equation or particle tracking. Results demonstrate strong agreement among the models in breakthrough behavior up to the 75th percentile. Significant deviations in first moments and well-clustered outputs led to the identification of inaccuracies in several models. Such findings exemplify the benefit of exercising these benchmarks and using the presented methods to test DFN flow and transport models.

Benchmark↗

DOE OSTI2023

Electrolytic Coagulant Generation for Treating Flowback and Produced Water for Reuse

This research investigated a novel electrochemical process for producing a ferric iron coagulant for use in treating flowback and produced water (FPW) from hydraulic fracturing and oil production operations. The electrolytic coagulant generation (ECG) system uses an electrochemical cell to produce acid and base from oilfield brine solutions. The acid is used to dissolve scrap iron to provide a Fe 3+ coagulating agent, and the base is used to neutralize the treated water. The costs for generating the ferric iron coagulant were determined as a function of current density and feed water salinity. The process was shown to be effective for removing colloidal bentonite particles from brine solutions. Here, the process has several advantages over conventional electrocoagulation using iron anodes, including: the ability to treat anoxic waters, elimination of electrode fouling, lower cost for the coagulant, and the ability to deliver Fe 3+ doses greater than 1 mM, since it is not limited by the amount of dissolved oxygen required to oxidize ferrous to ferric iron.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Interlaminar improvement of carbon fiber/epoxy composites via fluorine‐containing high‐epoxy‐value sizing agent

Abstract To improve the interfacial bonding effect of carbon fibers (CFs) and epoxy resins, we prepared a fluorine‐containing high‐epoxy‐value sizing agent (named TS) in this article. It is an emulsion with a more uniform particle size distribution and higher stability better than a commercial Takemoto sizing agent. In addition, sulfonic acid groups can improve the hydrophilicity of the TS, and the presence of epoxy groups enhances the wettability between CFs and the matrix. The properties of the sizing agents were examined by Fourier transform infrared spectroscopy, dynamic light scattering, and thermogravimetric analysis. The sized CFs were evaluated by scanning electron microscopy, x‐ray photoelectron spectroscopy, monofilament tensile test, and dynamic contact angle. Afterward, CF/epoxy composites were prepared, and their fracture morphology and interlaminar shear strength (ILSS) were examined. Results indicated that the TS sizing significantly increased the content of activated carbon on the surface of the CFs and improved the bonding effect between the fiber and the matrix. After TS was sized, the ILSS increased from 49.64 to 58.74 MPa, 18.34% higher than unsized CF/epoxy composites, showing the prominent interfacial reinforcement better than commercial Takemoto.

Qiu, Zhijie↗