Search NASA⌕ Search

SEARCH · Search NASA

Results for “permeability enhancement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Advective gas flow in bentonite: Development and comparison of enhanced multi-phase numerical approaches

Understanding the impact of repository gas, generated from degradation of waste and its interaction with the host rock, is essential when assessing the performance and safety function of long-term disposal systems for radioactive waste. Numerical models based on conventional multi-phase flow theory have historically been applied to predict the outcome and impact of gas flow on different repository components. However, they remain unable to describe the full complexity of the physical processes observed in water-saturated experiments (e.g., creation of dilatant pathways) and thus, the development of novel representations for their description is required when assessing fully saturated clay-based systems. This was the primary focus of Task A within the international cooperative project DECOVALEX-2019 (D-2019) and refinement of these approaches is the primary focus of this study (Task B in the current phase of DECOVALEX-2023). This paper summarises development of enhanced numerical representations of key processes and compares the performance of each model against high-quality laboratory test data. Experimental data reveals that gas percolation in water-saturated compacted bentonite is characterised by four key features: (i) a quiescence phase, followed by (ii) the gas breakthrough, which leads to a (iii) peak value, which is then followed by (iv) a negative decay. Three models based on the multiphase flow theory have been developed. These models can provide good initial values and reasonable responses for gas breakthrough (although some of them still predict a too-smooth response). Peak gas pressure values are in general reasonably well captured, although maximum radial stress differences are observed at 48 mm from the base of the sample. Here, numerical peak values of 12.8 MPa are predicted, whereas experimental values are about 11 MPa. These models are also capable of providing a reasonable representation of the negative pressure decay following peak pressure. However, other key specific features (such as the timing of gas breakthrough) still require a better representation. The model simulations and their comparison with experimental data show that these models need to be further improved with respect to model parameter calibration, the numerical representation of spatial heterogeneities in material properties and flow localisation, and the upscaling of the related physical processes and parameters. To further understand gas flow localisation, a new conceptual model has been developed, which shows that discrete channels can possibly be induced through the instability of gas-bentonite interface during gas injection, thus providing a new perspective for modeling gas percolation in low-permeability deformable media.

58 GEOSCIENCES↗
DOE OSTI2021

Machine Learning to Identify Geologic Factors Associated with Production in Geothermal Fields: A Case-Study Using 3D Geologic Data from Brady Geothermal Field and NMFk

In this paper, we present an analysis using unsupervised machine learning (ML) to identify the key geologic factors that contribute to the geothermal production in Brady geothermal field. Brady is a hydrothermal system in northwestern Nevada that supports both electricity production and direct use of hydrothermal fluids. Transmissive fuid-fow pathways are relatively rare in the subsurface, but are critical components of hydrothermal systems like Brady and many other types of fuid-fow systems in fractured rock. Here, we analyze geologic data with ML methods to unravel the local geologic controls on these pathways. The ML method, non-negative matrix factorization with k-means clustering (NMFk), is applied to a library of 14 3D geologic characteristics hypothesized to control hydrothermal circulation in the Brady geothermal field. Our results indicate that macro-scale faults and a local step-over in the fault system preferentially occur along production wells when compared to injection wells and non-productive wells. We infer that these are the key geologic characteristics that control the through-going hydrothermal transmission pathways at Brady. Our results demonstrate: (1) the specific geologic controls on the Brady hydrothermal system and (2) the efficacy of pairing ML techniques with 3D geologic characterization to enhance the understanding of subsurface processes. This submission includes the published journal article detailing this work, the published 3D geologic map of the Brady Geothermal Area used as a basis to develop structural and geological variables that are hypothesized to control or effect permeability or connectivity, 3D well data, along which geologic data were sampled for PCA analyses, and associated metadata file. This work was done using the GeoThermalCloud framework, which is part of SmartTensors (both are linked below).

15 GEOTHERMAL ENERGY↗
DOE OSTI2022

Performance Advantaged ..beta..-Ketone Containing Polymers - Benefits in Manufacturing, Performance, and End-of-Life

Biomass derived chemicals can possess extended functionality, often in the form of heteroatoms like oxygen and nitrogen, that can enable performance advantaged properties in emergent materials. These performance advantages can manifest in multiple ways such as reduced manufacturing intensity, better performance, or enhanced end-of-life options. One illustrative example of this concept is ..beta..-ketoadipic acid (..beta..KA), a C6 dicarboxylic acid with a ketone in its backbone. ..beta..KA can be obtained via biological cultivation from aromatic compounds, sugars, and even waste plastics. When ..beta..KA is implemented into polymers, namely nylons, in place of adipic acid the overall material properties are increased. Specifically, the glass transition temperature (which is the measurement at which temperature a plastic softens) is increased by 69 degrees C and the water permeability is reduced by 20%. Molecular dynamic (MD) simulations reveal that the ..beta..-ketone in ..beta..KA leads to restricted movement across multiple backbone carbons when compared to adipic acid. Furthermore, MD simulations reveal that the ..beta..-ketone, when compared to no-ketone or an a-ketone, can lead to an increase in hydrogen bonding between neighboring chains. Both phenomena may help explain the molecular origin of the increases in polymer performance. When implemented into polyesters, namely PET, ..beta..KA can maintain the requisite performance while enabling enhanced degradation. Aside from performance advantages in thermomechanical performance, the production of ..beta..KA also is advantaged in its manufacturing. Although estimates for the minimum selling price (MSP) of ..beta..KA exceed adipic acid the manufacture of ..beta..KAwould reduce supply chain energy and GHG emissions by >50% and >30% respectively. Further TEA analysis reveals that the MSP of ..beta..KA is primarily driven by the feedstock cost while the capital expenditures are driven largely by fermentation costs. Overall, the work presented within will be illustrative of how biomass derived molecules, namely ..beta..KA, can manifest performance advantages across multiple benchmarks and may enable a path to market for biomass-derived materials.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗
DOE OSTI2023

Non-equilibrium molecular dynamics studies of thermal diffusion of hydrogen isotopes in low concentration zirconium hydrides

Tritium permeability in zirconium-based tritium getter critically impacts tritium storage and environmental safety during operation of tritium-producing burnable absorber rods (TPBARs). Previous experiments indicated that during irradiation operation, the hydrogen equilibrium pressured is increased. Further experimental and modeling studies suggested that the enhanced tritium release observed for reactor scale assemblies might be related to a thermal diffusion known as the Soret effect. A direct measurement of the Soret factor, however, has not been performed. To improve TPBAR and other nuclear applications, here we have applied two non-equilibrium molecular dynamics methods to study thermal diffusion of hydrogen isotopes in low-concentration zirconium hydrides. One of the methods produces sufficiently converged results to distinguish crystal orientation, isotope type, and concentration effects. In conclusion, with this method, crystal orientation, isotope type, and concentration effects are discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Southwest Regional Partnership on Carbon Sequestration: Phase III (Final Scientific/Technical Report)

The Southwest Regional Partnership on Carbon Sequestration (SWP) is one of 7 regional partnerships formed in 2003 under the U.S. Department of Energy’s (DOE) Regional Carbon Sequestration Partnerships (RCSPs) initiative. The overall purpose of the initiative was to help determine and implement the technology, infrastructure, and regulations most appropriate to promote carbon storage in different regions of the country. Covering Arizona, Colorado, New Mexico, Oklahoma, Utah, and parts of Texas, Wyoming, and Kansas, the SWP evaluated regional carbon storage and utilization potential and focused on technologies and sites that could complement the region’s strong position in energy production. The project progressed through three phases: • Phase I (2003–2005): Characterized regional geologic formations and CO 2 sources, assessed sequestration potential, and identified pilot test sites. • Phase II (2005–2013): Conducted small-scale field tests to validate sequestration methods, including geologic and terrestrial projects. • Phase III (2008–2022): Demonstrated large-scale CO 2 injection at a commercial oil field to test monitoring, verification, and long-term storage strategies. This report covers Phase III. The final project site, the Farnsworth Unit (FWU) in Texas, provided real-world testing of reservoir characterization, monitoring, and risk evaluation tools and processes that could be used in any commercial scale carbon capture, utilization, and storage (CCUS) project. Extensive data collection and analysis helped refine best practices for reservoir characterization, injection monitoring, and storage verification. The SWP contributed to national databases, DOE best practice manuals, and regional geological assessments to support future sequestration efforts. Key lessons learned include the importance of robust data management, strategic site selection, regulatory navigation, and effective industry collaboration. The project’s findings will inform ongoing and future carbon storage initiatives. Task 1 (Regional Characterization) • The SWP continued to participate in national outreach efforts and NATCARB. • The SWP evaluated multiple potential sites before selecting the FWU as the primary field test location. Task 2 (Public Outreach and Education) • The SWP contributed to national databases, DOE best practice manuals, and regional geological assessments to support future sequestration efforts. Task 3 (Permitting and Regulatory Compliance) • The SWP ensured compliance with federal and state regulations, including National Environmental Policy Act (NEPA) requirements. • The SWP obtained all necessary permits for drilling, injection, and monitoring activities. Task 4 (Site Characterization and Planning) • The SWP developed work plans for four key activities: characterization, simulation, monitoring and verification, and risk evaluation. • The SWP collected and synthesized legacy data from multiple sources to build initial static geological models and dynamic reservoir models demonstrating project feasibility. • The SWP conducted an initial risk evaluation and developed mitigation plans. Task 5 (Field Operations and Data Collection) • The SWP drilled, logged, and cored three characterization wells to gather critical subsurface data. • The SWP conducted multiple geophysical surveys, including 3D seismic, crosswell seismic, and vertical seismic profiling, to improve reservoir characterization. Task 6 (Monitoring and Verification) • The SWP performed extensive geological characterization using data from characterization wells and seismic surveys. • The SWP established a surface monitoring network to track CO 2 flux in soil gas, groundwater chemistry, and near-surface atmospheric CO 2 levels. • The SWP built and refined reservoir models to study the effects of relative permeability on simulation behavior and improve calibration with experimental data. Task 7 (Risk Assessment and Model Refinement) • The SWP conducted multiple studies to evaluate reservoir integrity, predict CO 2 plume behavior and improve predictive modeling capabilities. • The SWP refined geological models and used them to enhance the accuracy of simulation models. • The SWP continued quantitative risk assessment of top-ranked risks and strengthened the link between qualitative and quantitative risk methodologies.

02 PETROLEUM↗
DOE OSTI2021

Impact of Nickel Ions on the Oxygen Reduction Reaction Kinetics of Pt and on Oxygen Diffusion through Ionomer Thin Films

The effects of dissolved nickel on the oxygen reduction reaction (ORR) kinetics and oxygen transport properties of perfluorosulfonic acid (PFSA) thin films were investigated using rotating disk electrode (RDE) measurements of ORR on a PFSA-coated platinum electrode. The electrochemical characterization in 0.1 M perchloric acid (HClO 4 ) with and without added Ni 2+ quantitatively measured the impact of ionic interactions between the Ni 2+ cations and sulfonate (SO 3 - ) anions on oxygen transport through the PFSA thin film. Cyclic voltammetry (CV) curves in deaerated electrolyte showed that Ni 2+ cations diffusing through the PFSA thin film interact with the Pt surface altering the hydrogen underpotential deposition and stripping processes and decreasing ORR kinetics. The RDE limiting current results point to reduced permeability of oxygen through PFSA-Ni 2+ compared to PFSA-H + . Furthermore, the results indicate that transition metals leached from Pt alloy catalyst may be detrimental not only to the intrinsic ORR kinetics of the PEFC cathode catalyst through loss of the ORR-enhancing transition metal, but may also inhibit the diffusion of oxygen to the catalytic sites and poison the ORR.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Utah FORGE 5-2557: Fluid and Temperature in Fracture Mechanics and Coupled THMC Processes - Workshop Presentation

This is a presentation on the Role of Fluid and Temperature in Fracture Mechanics and Coupled Thermo-Hydro-Mechanical-Chemical (THMC) Processes for Enhanced Geothermal Systems project by Purdue University, presented by Distinguished Professor of Physics & Astronomy, Laura J. Pyrak-Nolte. The project's objective was to develop and validate a macroscopic model that accounts for local deformation/frictional behavior, seismic/aseismic behavior, chemical reactions, and determine the adequacy of classic Coulomb failure vs. rate-and-state friction. This presentation was featured in the Utah FORGE R&D Annual Workshop on September 8, 2023. The workshop provided a valuable opportunity to explore the progress made in each of the 17 Research and Development projects funded under Solicitation 2020-1 which aim to enhance our understanding of the crucial factors influencing the development of Enhanced Geothermal Systems (EGS) reservoirs and resources.

15 GEOTHERMAL ENERGY↗
DOE OSTI2020

Microfluidic Fabrication Techniques for High-Pressure Testing of Microscale Supercritical CO 2 Foam Transport in Fractured Unconventional Reservoirs

Pressure limitations of many microfluidic platforms have been a significant challenge in microfluidic experimental studies of fractured media. As a result, these platforms have not been fully exploited for direct observation of high-pressure transport in fractures. This work introduces microfluidic platforms that enable direct observation of multiphase flow in devices featuring surrogate permeable media and fractured systems. Such platforms provide a pathway to address important and timely questions such as those related to CO 2 capture, utilization and storage. This work provides a detailed description of the fabrication techniques and an experimental setup that may serve to analyze the behavior of supercritical CO 2 (scCO 2 ) foam, its structure and stability. Such studies provide important insights regarding enhanced oil recovery processes and the role of hydraulic fractures in resource recovery from unconventional reservoirs. This work presents a comparative study of microfluidic devices developed using two different techniques: photolithography/wet-etching/ thermal-bonding versus Selective Laser-induced Etching. Both techniques result in devices that are chemically and physically resistant and tolerant of high pressure and temperature conditions that correspond to subsurface systems of interest. Both techniques provide pathways to high-precision etched microchannels and capable lab-on-chip devices. Photolithography/wet-etching, however, enables fabrication of complex channel networks with complex geometries, which would be a challenging task for laser etching techniques. This work summarizes a step-by-step photolithography, wet-etching and glass thermal-bonding protocol and, presents representative observations of foam transport with relevance to oil recovery from unconventional tight and shale formations. In conclusion, this work describes the use of a high resolution monochromatic sensor to observe scCO 2 foam behavior where the entirety of the permeable medium is observed simultaneously while preserving the resolution needed to resolve features as small as 10 μm.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Hydraulic fracturing experiments at 1500 m depth in a deep mine: Highlights from the kISMET project

In support of the U.S. DOE SubTER Crosscut initiative, we established a field test facility in a deep mine and designed and carried out in situ hydraulic fracturing experiments relevant to enhanced geothermal systems (EGS) in crystalline rock to characterize the stress field, understand the effects of rock fabric on fracturing, and gain experience in monitoring using geophysical methods. The project also included pre- and post-fracturing simulation and analysis, and laboratory measurements and experiments. The kISMET (permeability (k) and Induced Seismicity Management for Energy Technologies) site was established in the West Access Drift of the Sanford Underground Research Facility (SURF) 4757 ft (1450 m) below ground (on the 4850 ft level (4850L)) in phyllite of the Precambrian Poorman Formation. We drilled and continuously cored five near-vertical boreholes in a line on 3 m (10 ft) spacing, deviating the two outermost boreholes slightly to create a five-spot pattern around the test borehole centered in the test volume 40 m below the drift invert (floor) at a total depth of ~1490 m (4890 ft). Laboratory measurements of core from the center test borehole showed P-wave velocity heterogeneity along each core indicating strong, fine-scale (~1 cm or smaller) changes in the mechanical properties of the rock. Field measurements of the stress field by hydraulic fracturing showed that the minimum horizontal stress at the kISMET site averages 21.7 MPa (3146 psi) trending approximately N-S (356 degrees azimuth) and plunging slightly NNW at 12°. The vertical and horizontal maximum stresses are similar in magnitude at 42-44 MPa (6090-6380 psi) for the depths of testing, which averaged approximately 1530 m (5030 ft). Hydraulic fractures were remarkably uniform suggesting core-scale and larger rock fabric did not play a role in controlling fracture orientation. Analytical solutions suggest that the fracture radius of the large fracture (stimulation test) was more than 6 m (20 ft), depending on the unknown amount of leak-off.

Oldenburg, C↗
DOE OSTI2024

Surface-Enhanced Raman Spectroscopy Combined with Multivariate Analysis for Fingerprinting Clinically Similar Fibromyalgia and Long COVID Syndromes

Fibromyalgia (FM) is a chronic central sensitivity syndrome characterized by augmented pain processing at diffuse body sites and presents as a multimorbid clinical condition. Long COVID (LC) is a heterogenous clinical syndrome that affects 10–20% of individuals following COVID-19 infection. FM and LC share similarities with regard to the pain and other clinical symptoms experienced, thereby posing a challenge for accurate diagnosis. This research explores the feasibility of using surface-enhanced Raman spectroscopy (SERS) combined with soft independent modelling of class analogies (SIMCAs) to develop classification models differentiating LC and FM. Venous blood samples were collected using two supports, dried bloodspot cards (DBS, n = 48 FM and n = 46 LC) and volumetric absorptive micro-sampling tips (VAMS, n = 39 FM and n = 39 LC). A semi-permeable membrane (10 kDa) was used to extract low molecular fraction (LMF) from the blood samples, and Raman spectra were acquired using SERS with gold nanoparticles (AuNPs). Soft independent modelling of class analogy (SIMCA) models developed with spectral data of blood samples collected in VAMS tips showed superior performance with a validation performance of 100% accuracy, sensitivity, and specificity, achieving an excellent classification accuracy of 0.86 area under the curve (AUC). Amide groups, aromatic and acidic amino acids were responsible for the discrimination patterns among FM and LC syndromes, emphasizing the findings from our previous studies. Overall, our results demonstrate the ability of AuNP SERS to identify unique metabolites that can be potentially used as spectral biomarkers to differentiate FM and LC.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2025

Biobased Poly(dodecylene Furanoate) with Inherent Advantages in Performance and Circularity

Biobased polymers are gaining traction toward more sustainable flexible-film packaging, yet overcoming trade-offs between their performance properties and end-of-life (EoL) options still remains a challenge. Here, it is shown that biobased poly(dodecylene 2,5-furanoate) (PDDF), synthesized via both step-growth polycondensation and chain-growth ring-opening polymerization methods, exhibits advantages not only in gas barrier properties but also in EoL options due to its biodegradability and closed-loop chemical circularity. Specifically, PDDF displays significantly lower oxygen and carbon dioxide permeability than commercial poly(butylene adipate-co-terephthalate) (PBAT) and linear low-density polyethylene , alongside a markedly higher modulus (by ≈3 ×) and reduced water vapor transmission rate compared to PBAT. This superior performance is attributed to the inherently rigid, polar, H-bonding furan rings that enhance chain interaction, packing and crystallinity and thus reduce free volume impeding gas diffusion, while the long hydrophobic dodecylene segments inhibit water permeation. Furthermore, PDDF can be recycled back to its cyclic monomer by base-catalyzed depolymerization or diester and diol monomers by simple methanolysis. These superior barrier properties, coupled with biodegradation and closed-loop circularity, highlight the potential of the biobased PDDF as a more sustainable alternative for packaging.

Poly(dodecylene 2,5-furanoate) (PDDF)↗
DOE OSTI2025

On the viability of stimulated hydrogen generation from iron-rich formations

Hydrogen-based technologies present a promising solution for the global energy transition. In addition to electrolytic production, subsurface geological formations provide a potential natural source of hydrogen. Iron-rich ultramafic rocks, in particular, are favorable for hydrogen generation through natural processes such as serpentinization. Naturally occurring reactions and migration can be enhanced through various types of stimulation, including thermal, hydraulic, and chemical treatment. Through numerical simulations, we analyzed the complex interplay of factors influencing the production and migration within the subsurface, emphasizing the importance of different stimulation techniques, catalysts, and conditions. Our findings indicate that key parameters, such as damage zone permeability and width, significantly impact producible hydrogen mass. Our results indicate that a combination of large damage zone widths, high permeability, and a stimulated reaction rate of 1 × 10 -9 can yield economically viable production rates of up to 1 kg s -1 at the wellhead. Moreover, the availability of ferrous iron, rather than the serpentinization rate itself, has been identified as the primary limiting factor in achieving economically sustainable hydrogen production. In conclusion, while an unstimulated rock volume of 0.165 km 3 yields only 45t of hydrogen in two years, various stimulation techniques can increase production to 18500t.

08 - HYDROGEN↗
DOE OSTI2025

Insights Into Seismicity Associated With Flexibly Operating Enhanced Geothermal System From Real‐Time Distributed Acoustic Sensing

Enhanced Geothermal Systems (EGS) have the capacity to broaden the accessible resource pool for geothermal power generation. Traditionally viewed as a “baseload” resource, their flexible operation might also enable dispatchable load‐following generation and long‐term energy storage, aligning them with the evolving landscape of decarbonized electricity systems. However, increasing permeability and extracting energy during EGS operations can induce microseismic events; for many prior EGS efforts, some associated seismicity has been observed. While energetically beneficial, the flexibility of EGS operations prompts our inquiry into whether new types of operations will yield previously unseen seismicity patterns. We demonstrate the use of distributed acoustic sensing (DAS) with real‐time edge computing to monitor seismicity during a pilot test of a cyclically operated EGS facility at the Blue Mountain geothermal field. Our focus lies in uncovering seismicity insights from the real‐time microseismic catalog, particularly during load‐following dispatchability tests simulating flexible EGS operation. Here, we find that variations in pore pressure consistently correlate with seismicity, and that controlling pressure cycles during flexible operations appears to constrain microseismic activity during subsequent cycles. The spatio‐temporal evolution of microseismic clouds recorded during cyclic injection cycles fits diffusive models over our available observation period. Additionally, seismicity elevation lags behind pore pressure increases, likely due to pressure diffusion to the fracture system boundary. Through real‐time monitoring, we offer novel insights into seismicity associated with flexibly operating EGS. Our findings suggest that leveraging DAS and edge computing can inform EGS operations and help mitigate induced seismicity.

Chamarczuk, Michal [Rice Univ., Houston, TX (Unite↗
DOE OSTI2022

LANL Activities on Mechanistic Approach to Analyzing and Improving Unconventional Hydrocarbon Production

Hydrocarbon production from shale reservoirs is inherently inefficient and challenging since these are low permeability plays. In addition, there is a limited understanding of the fundamentals and the controlling mechanisms, further complicating how to optimize these plays. Herein, we summarize our experimental and computational efforts fully and partially supported by the fundamental shale portfolio to reveal unconventional shale fundamentals and devise development strategies to enhance extraction efficiency with a minimal environmental footprint. Integrating these fundamentals with machine learning, we outline a pathway to improve the predictive power of our models, which enhances the forecast quality of production, thereby improving the economics of operations in unconventional reservoirs. For instance, we have developed science informed workflows and platforms for optimizing pressure-drawdown at a site, which allow operators to make reservoir-management decisions that optimize recovery in consideration of future production. Recently, our work relies on the hybridization of physics-based prediction and machine learning, whereby accurate synthetic data (combined with available site data) can enable the application of machine learning methods for rapid forecasting and optimization. Consequently, the workflow and platform are readily extendable to operations at other sites, plays, and basins.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2021

Oxidation and Associated Pore Structure Modification During Experimental Alteration of Granite

Weathering plays a crucial role in a number of environmental processes, and the microstructure and evolution of multi-scale pore space is a critically important factor in the weathering of geological formations. In igneous rocks the infiltration of meteoric water into initially relatively dry material can cause the rock to begin to disaggregate, increasing porosity and surface area, and allowing further disaggregation and weathering to occur. These processes, in turn, allow biota to colonize the rock, further enhancing the weathering rate. In some igneous rocks this may be driven by oxidation of primary minerals. One such mineral, biotite, has been repeatedly mentioned as a cause of cracking during oxidation. However, the scale-dependence of the processes by which this occurs are poorly understood. We cannot, therefore, accurately extrapolate laboratory reaction rates to the field in predictive numerical models. In order to better understand the effects of oxidation and test the hypothesis that fracture and disaggregation are initiated by swelling of oxidizing biotites, we reacted granite cores in a selenic acid-rich aqueous solution at 200°C for up to 438 days. Elevated temperatures and selenic acid were used to provide relatively fast reaction rates and highly oxidizing conditions in sealed reaction vessels. These experiments were analyzed using a combination of imaging, X-ray diffraction, Mössbauer spectroscopy, and small- and ultra-small angle neutron scattering to interrogate porosity and microfracture formation. The experimental results show little observable biotite swelling, but significant transport and growth of iron oxides and/or clays along grain boundaries throughout the sample. Significant increases in porosity were also observed at the sample rim, likely associated with feldspar alteration. Fractures and transport were observed throughout the core, suggesting that stresses due to crystallization pressures caused by the growing iron phases may be the initiating factors in granite weathering, possibly followed by biotite swelling after sufficient permeability is achieved.

Anovitz, Lawrence M.↗
DOE OSTI2025

A comparative analysis of numerical approaches for the description of gas flow in clay-based repository systems: From a laboratory to a large-scale gas injection test

There is nowadays a consensus among many countries that geological disposal is a favourable solution for the long-term management. Although different host formations and different barrier systems are under consideration around the world, clay-based materials form an important component for waste isolation in most national programmes. Hence, a good comprehension of the effect of gas flow on the hydro-mechanical behaviour of clay-based soils is essential, both at laboratory and field scale. Task B under the international cooperative project DECOVALEX-2023 has recently shown that, after some enhancement, models can be employed to reproduce laboratory scale tests, even with different sample geometries 37 . However, further work is required to understand whether they can be applied to simulate a large-scale experiment. Up-scaling of models for the advective transport of gas through clay-based low permeable material presents a number of problems related to the difficulty in obtaining consistent hydrogeological parameters and constitutive relationships at both laboratory and field scale. Based on a unique dataset from a large-scale gas injection test (Lasgit) performed at the Äspö Hard Rock Laboratory (Sweden), Task B within DECOVALEX-2023 has explored the refinement of these numerical strategies applied to the simulation of gas flow. Work performed within the task reveals that codes do not need to be substantially modified from the laboratory models to reproduce full-scale tests: indeed, model parameters calibrated and validated at laboratory scale have been applied to predict field scale gas flow at Lasgit, including peak gas pressure and injected cumulative gas volume. By means of (1) the introduction of interfaces between blocks to reflect the experimental configuration and the (2) adjustment of some parameters (e.g., higher permeability), the updated models are able to represent most of the key features observed in the experimental data, even at a large scale.

Tamayo-Mas, E↗
DOE OSTI2024

High-performance cementitious composites containing nanostructured carbon additives made from charred coal fines

Carbon-based nanomaterials, such as carbon nanoplatelets, graphene oxide, and carbon quantum dots, have many possible end-use applications due to their ability to impart unique mechanical, electrical, thermal, and optical properties to cement composites. Despite this potential, these materials are rarely used in the construction industry due to high material costs and limited data on performance and durability. In this study, domestic coal is used to fabricate low-cost carbon nanomaterials that can be used economically in cement formulations. A range of chemical and physical processing approaches are employed to control the size, morphology, and chemical functionalization of the carbon nanomaterial, which improves its miscibility with cement formulations and its impact on mechanical properties and durability. At loadings of 0.01 to 0.07 wt.% of coal-derived carbon nanomaterial, the compressive and flexural strength of cement samples are enhanced by 24% and 23%, respectively, in comparison to neat cement. At loadings of 0.02 to 0.06 wt.%, the compressive and flexural strength of concrete composites increases by 28% and 21%, respectively, in comparison to neat samples. Additionally, the carbon nanomaterial additives studied in this work reduce cement porosity by 36%, permeability by 86%, and chloride penetration depth by 60%. These results illustrate that low-loadings of coal-derived carbon nanomaterial additives can improve the mechanical properties, durability, and corrosion resistance of cement composites.

36 MATERIALS SCIENCE↗