Search NASA⌕ Search

SEARCH · Search NASA

Results for “pilot study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1959

Studies of Pilot Control During Launching and Reentry of Space Vehicles, Utilizing the Human Centrifuge

With the ever increasing complexity of airplanes and the nearness to reality of manned space vehicles the use of pilot-controlled flight simulators has become imperative. The state of the art in flight simulation has progressed well with the demand. Pilot-controlled flight simulators are finding increasing uses in aeromedical research, airplane and airplane systems design, and preflight training. At the present many flight simulators are in existence with various degrees of sophistication and sundry purposes. These vary from fixed base simulators where the pilot applies control inputs according to visual cues presented to him on an instrument display to moving base simulators where various combinations of angular and linear motions are added in an attempt to improve the flight simulation.

Clark, Carl C.↗
NASA NTRS1973

A piloted simulation study of the effects of controller force gradient in VTOL hovering flight

A study of the effect of control force gradient on the VTOL visual hovering task was conducted on the NASA-Ames Research Center Six-Degree-of-Freedom Motion Simulator. Lateral control force-gradient characteristics were evaluated in combination with three different types of stabilization systems: An unstabilized (acceleration) system, a rate-stabilized system, and two attitude-stabilized systems. The effects of gust disturbances were included in the control force evaluation for the attitude systems. A force gradient of 1.0 lb/in was within the optimum range for all control systems and conditions evaluated in this study.

Fry, E. B.↗
NASA NTRS1975

A study of pilot behavior during controlling the lateral directional motion of airplanes in turbulent air

The pilot behaviors controlling the lateral directional motion of airplanes in turbulent air have been investigated by using the pilot transfer function which has been obtained by the analysis of flight test data. The pilot uses the gains for the aileron manipulation proportionally to bank angle so as to minimize r.m.s. of bank angle. The pilot rudder manipulations are done proportionally to rolling velocity, yawing velocity, and yaw angle. Namely, the pilot carries out the cross control for the rudder.

Beppu, G.↗
NASA NTRS1978

Results of piloted simulator studies of fighter aircraft at high angles of attack

The experience gained at the NASA Langley Research Center during the application of simulator techniques to high angle of attack flight conditions for several current fighters is discussed. The discussion includes (1) the simulator hardware, (2) requirements for static and dynamic aerodynamic data inputs, (3) evaluation procedures, (4) correlation with flight, and (5) the effects of dynamic stability parameters. Results obtained with the simulator technique have correlated well with flight test experience, resulting in early identification of potential problems, identification of critical flight conditions, and solutions to various deficiencies in stability and control characteristics. Dynamic stability parameters, results indicate that certain parameters can have a large influence on the flying qualities and tactical effectiveness of fighters at high angles of attack.

Chambers, J. R.↗
NASA NTRS1991

Piloted simulator studies of the HL-20 Lifting Body

An overview is presented of the concept, design and development of the NASA Langley Lifting Body, and the flight simulator studies that have been performed. Attention is given to the aerodynamic shape of the HL-20, vehicle and simulator/cockpit description, and evolution of the HL-20 aerodynamic model. The flight simulation studies have demonstrated the HL-20 to be a viable design for accomplishing precise, unpowered, horizontal landings.

Rivers, Robert A.↗
NASA NTRS1996

JOVE Pilot Research Study in Astronomy and Microgravity Sciences

The purpose of this project was to develop hardware and software facilities for evaluating the biomechanical interactions between human hands and space suit gloves. The first task was to measure finger joint angles inside space suit gloves. A preliminary survey identified three potential systems which could be used in the proposed study. In response to the current market situation, a glove for measuring the positions of the hand inside a space suit has been developed. A prototype of the glove has been constructed to demonstrate its sensing technologies. There are two types of sensors in the glove. The positions of the fingers are measured using bend sensors based on the CyberGlove design. This sensor consists of two strain gages mounted to a 0.003 inch thick mylar sheet. The sensor is encapsulated using 0.001 inch kapton film to give it sufficient rigidity. Along gage is used to average the strain generated in the sensor due to bending This average strain produces an output signal proportional to the angle of the bend. The force sensor consists of conductive ink sandwiched between two plastic sheets. An electrode is printed on one of the plastic sheets using silver ink. The resistance of the ink is sensitive to pressure.

Strauss, Alvin M.↗
NASA NTRS1995

JOVE Pilot Research Study in Astronomy and Microgravity Sciences

The purpose of this project was to develop hardware and software facilities for evaluating the biomechanical interactions between human hands and space suit gloves. We have constructed a prototype of the glove to demonstrate its sensing technologies. There are two types of sensors in the glove. The positions of the fingers are measured using bend sensors based on the CyberGlove design. This sensor consists of two strain gages mounted to a 0.003 inch thick mylar sheet. The sensor is encapsulated using 0.001 inch kapton film to give it sufficient rigidity. A long gage is used to average the strain generated in the sensor due to bending. This average strain produces an output signal proportional to the angle of the bend. The force sensor, FSR, is manufactured by Interlink. It consists of conductive ink sandwiched between two plastic sheets. An electrode is printed on one of the plastic sheets using silver ink. When the electrode makes contact, current flows through the conductive ink. The resistance of the ink pad is sensitive to pressure. We have also developed circuits for exciting and measuring the sensors. The current version requires a single sided twelve volt power supply which is one inch long and 0.4 inches in diameter.

Strauss, Alvin M.↗
NASA NTRS1997

Piloted Simulation Study of Wake Encounters

The objective of this current research is to determine an acceptable level of vortex roll disturbance for worst-case encounter geometries during normal, routine operations. This includes: determining the boundary & metric(s), and defining evaluation factors & procedures. The discussion includes: simulation hardware, research simulator software, and research approach & observations.

Stewart, Eric↗
DOE OSTI2023

Economic and environmental feasibility of recycling flexible plastic packaging from single stream collection

As demand for plastic increases, there is an urgent need to ramp up its collection and recycling rate. This study reports results of a pilot study in the United States to recycle flexible plastic packaging (FPP) from single stream curbside collection focusing on both the economic feasibility and carbon footprint. To explore the marketability of recycled FPP, four down-stream market pathways were studied, including roof coverboard, plastic pellets, pallets, and film. In this work, results indicated that (1) the cleaning and pelletizing process at reclaimers contributed the most to the total greenhouse gas (GHG) emissions of recycled FPP products, and (2) the GHG emissions of recycled FPP products in all four pathways are lower than the comparator products. Therefore, using a higher percentage of recycled FPP substituted in a product can result in greater GHG emission reductions. All the recycled FPP products also showed favorable economics compared to their direct competitors.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗