Search NASA⌕ Search

SEARCH · Search NASA

Results for “printing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Boosting Piezoelectricity by 3D Printing PVDF‐MoS 2 Composite as a Conformal and High‐Sensitivity Piezoelectric Sensor

Abstract Additively manufactured flexible and high‐performance piezoelectric devices are highly desirable for sensing and energy harvesting of 3D conformal structures. Herein, the study reports a significantly enhanced piezoelectricity in polyvinylidene fluoride (PVDF) achieved through the in situ dipole alignment of PVDF within PVDF‐2D molybdenum disulfide (2D MoS 2 ) composite by 3D printing. The shear stress‐induced dipole poling of PVDF and 2D MoS 2 alignment are harnessed during 3D printing to boost piezoelectricity without requiring a post‐poling process. The results show a remarkable, more than the eight‐fold increment in the piezoelectric coefficient ( d 33 ) for 3D printed PVDF‐8wt.% MoS 2 composite over cast neat PVDF. The underlying mechanism of piezoelectric property enhancement is attributed to the increased volume fraction of β phase in PVDF, filler fraction, heterogeneous strain distribution around PVDF‐MoS 2 interfaces, and strain transfer to the nanofillers as confirmed by microstructural analysis and finite element simulation. These results provide a promising route to design and fabricate high‐performance 3D piezoelectric devices via 3D printing for next‐generation sensors and mechanical–electronic conformal devices.

2D MoS2↗
DOE OSTI2025

Print-and-Plate Architected Electrodes for Electrochemical Transformations Under Flow

Flow cell electrodes are typically composed of porous carbon materials, such as papers, felts, and cloths. However, their random architecture hinders the fundamental characterization of electrode structure-performance relationships during in situ operation of porous electrochemical flow systems. This work describes a “print-and-plate” method that combines direct ink writing of micro-periodic lattices with a two-step metal plating process that converts them into highly conductive (sheet resistance 40 mΩ sq -1 ) electrodes. Their operando performance is assessed in an anthraquinone disulfonic acid half-cell using widefield electrochemical fluorescence microscopy, where output current and fluorescence intensity are in excellent agreement. The pressure drop associated with flow through three electrode designs is determined via simulations from which the most efficient design is identified and manufactured via print-and-plate. Confocal fluorescence microscopy is then used to create a 3D map of the state of charge (SOC) inside this print-and-plate electrode. The experimental state of the charge map is in good agreement with computational predictions. The rapid design, simulation, and fabrication of print-and-plate electrodes enable fundamental investigations of how architected porosity affects electrochemical performance under flow.

3D-printing↗
DOE OSTI2022

Conductive Ink with Circular Life Cycle for Printed Electronics

Electronic waste carries energetic costs and an environmental burden rivaling that of plastic waste due to the rarity and toxicity of the heavy-metal components. Recyclable conductive composites are introduced for printed circuits formulated with polycaprolactone (PCL), conductive fillers, and enzyme/protectant nanoclusters. Circuits can be printed with flexibility (breaking strain ≈80%) and conductivity (≈2.1 × 10 4 S m -1 ). These composites are degraded at the end of life by immersion in warm water with programmable latency. Approximately 94% of the functional fillers can be recycled and reused with similar device performance. The printed circuits remain functional and degradable after shelf storage for at least 7 months at room temperature and one month of continuous operation under electrical voltage. Here, the present studies provide composite design toward recyclable and easily disposable printed electronics for applications such as wearable electronics, biosensors, and soft robotics.

36 MATERIALS SCIENCE↗
DOE OSTI2021

3D printing of anisotropic Sm–Fe–N nylon bonded permanent magnets

Abstract Fabricating a bonded magnet with a near‐net shape in suitable thermoplastic polymer binders is of paramount importance in the development of cost‐effective energy technologies. In this work, anisotropic Sm 2 Fe 17 N 3 (Sm–Fe–N) bonded magnets are additively printed using SmFeN anisotropic magnetic particles in a polymeric binder polyamide‐12 (PA12). The anisotropic SmFeN bonded magnets are fabricated by Big Area Additive Manufacturing followed by post‐printing alignment in a magnetic field. Optimal post‐alignment results in an enhanced remanence of ∼0.68 T in PA12 reflected in a parallel‐oriented (aligned) measured direction. The maximum energy product achieved for the additively printed anisotropic bonded magnet of Sm–Fe–N in PA12 polymer is 78.8 KJ m −3 . Our results show advanced processing flexibility with 3D printing of the development of SmFeN nylon bonded magnets designed for applications with no critical rare earth magnets.

42 ENGINEERING↗
DOE OSTI2022

Physical Models from Physical Templates Using Biocompatible Liquid Crystal Elastomers as Morphologically Programmable Inks For 3D Printing

Advanced manufacturing has received considerable attention as a tool for the fabrication of cell scaffolds however, finding ideal biocompatible and biodegradable materials that fit the correct parameters for 3D printing and guide cells to align remain a challenge. Herein, a photocrosslinkable smectic-A (Sm-A) liquid crystal elastomer (LCE) designed for 3D printing is presented, that promotes cell proliferation but most importantly induces cell anisotropy. The LCE-based bio-ink allows the 3D duplication of a highly complex brain structure generated from an animal model. Vascular tissue models are generated from fluorescently stained mouse tissue spatially imaged using confocal microscopy and subsequently processed to create a digital 3D model suitable for printing. The 3D structure is reproduced using a Digital Light Processing (DLP) stereolithography (SLA) desktop 3D printer. Synchrotron Small-Angle X-ray Diffraction (SAXD) data reveal a strong alignment of the LCE layering within the struts of the printed 3D scaffold. The resultant anisotropy of the LCE struts is then shown to direct cell growth. This study offers a simple approach to produce model tissues built within hours that promote cellular alignment.

3D cell culture↗
DOE OSTI2024

In-situ qualification and physics-based process design for aerosol jet printing via spatially correlated light scattering measurements

Aerosol jet printing is a contactless, digital, and additive technique broadly used for manufacturing flexible, hybrid, and conformal electronics. However, batch-to-batch variability has hindered widespread industry adoption and scaling to production volumes. Recently, light scattering measurements have emerged as a tool to measure aerosol volume fraction – a key parameter determining deposition rate – and have proven an effective feedback source for closed loop control on timescales ranging from minutes to hours. Here, the efficacy of light scattering measurements as a tool for in-situ qualification over shorter time durations is explored. To be the linear relationship between light scattering measurements and deposition rate was validated at 500 ms time intervals, allowing deposition rate to be mapped to positional coordinates and providing a new data stream to drive quality control assessments. Because light scattering measurements are indicative of a physical process parameter, they were substituted into equations for resistance and sheet resistance, resulting in predictions nominally within 10% of measured values for sets of printed devices. Finally, to highlight a more active utility, light scattering measurements were employed in a print repair framework, successfully repairing prints with randomly induced defects to within 5% of the measured resistance of a control set.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Macroscale Control of Reactivity using 3D Printed Materials with Intrinsic Catalytic Properties

The morphology of heterogeneous catalysts can impact their performance. However, standard manufacturing methods like extrusion or pelleting offer little options for tailoring catalyst shape. Herein, stereolithographic 3D printing is used to produce catalysts with controlled topologies to enhance their performance. A series of magnetic stir-bar compartments (SBC) were 3D printed and tested as catalysts for sucrose hydrolysis. The SBC were printed using acrylic acid (AA) and 1,6-hexanediol diacrylate (HDDA) as acid sites and hydrophobic crosslinking domains, respectively. Variations in the number and tilt direction of the SBC blades produced significant changes in their apparent catalytic activities. These changes resulted from differences in the fraction of active surface effectively interacting with the reactants in solution, as revealed by computational fluid dynamics simulations. Moreover, varying HDDA:AA ratios in SBC regulated reactant-surface interactions to control catalytic activity. Overall, 3D printing catalysts enables quick performance optimization by simultaneously controlling macroscopic structure and molecular composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Physics augmented machine learning discovery of composition-dependent constitutive laws for 3D printed digital materials

Multi-material 3D printing, particularly through polymer jetting, enables the fabrication of digital materials by mixing distinct photopolymers at the micron scale within a single build to create a composite with tunable mechanical properties. Here, this work presents an integrated experimental and computational investigation into the composition-dependent mechanical behavior of 3D printed digital materials. We experimentally characterize five formulations, combining soft and rigid UV-cured polymers under uniaxial tension and torsion across three strain and twist rates. The results reveal nonlinear and rate-dependent responses that strongly depend on composition. To model this behavior, we develop a physics-augmented neural network (PANN) that combines a partially input convex neural network (pICNN) for learning the composition-dependent hyperelastic strain energy function with a quasi-linear viscoelastic (QLV) formulation for time-dependent response. The pICNN ensures convexity with respect to strain invariants while allowing non-convex dependence on composition. To enhance interpretability, we apply $L_0$ sparsification. For the time-dependent response, we introduce a multilayer perceptron (MLP) to predict viscoelastic relaxation parameters from composition. The proposed model accurately captures the nonlinear, rate-dependent behavior of 3D printed digital materials in both uniaxial tension and torsion, achieving high predictive accuracy for interpolated material compositions. This approach provides a scalable framework for automated, composition-aware constitutive model discovery for multi-material 3D printing.

Constitutive modeling↗
DOE OSTI2021

Investigation of chemical stabilities and contact angle of 3D printed polymers with CO 2 capture solvents to enhance absorber performance

Increasing absorption rate in aqueous amine CCS systems is one avenue to decrease capital cost by reducing the overall size of the absorber column. One potential route is by replacing conventional steel packing with custom designed packing made from 3D printed polymers. 3D printing offers endless flexibility in packing designs to better enhance liquid/gas contact, increase CO 2 mass transfer and create compact absorber columns. Additionally, before exploring novel packing designs, it is necessary to identify polymer materials that can be 3D printed while also showing long-term physical and surface property stability upon exposure to corrosive amine solutions. Four polymers that are commonly used for 3D printing were evaluated using CO 2 -loaded amine solution at temperatures typically observed in the absorber column. Three polymers, high-density polystyrene (HDPS), acrylonitrile butadiene styrene (ABS) and nylon were found to be physically stable after 5000 hr of amine exposure at temperatures up to 60 °C. The contact angle (wetting) of water and CO 2 -loaded aqueous amine solution on the polymer surfaces were also stable after exposure to the CO2-loaded amine solution.

36 MATERIALS SCIENCE↗
DOE OSTI2020

4D Printing via an Unconventional Fused Deposition Modeling Route to High-Performance Thermosets

An unprecedented four-dimensional (4D) printing process allowing high-performance and shape memory thermoset to be printed, for the first time, by fused deposition modeling (FDM) with isotropic properties has been achieved. Here, bisphenol A-based epoxy and benzoxazine were formulated to a low-temperature thermoplastic and high-temperature thermoset resin, which is melt-extrudable and can be postcured into covalently cross-linked material. Carbon nanotube (CNT) was added in the resin to work as both mechanical enhancement filler and rheology modifier to prevent shape deformation during postcuring process. The cross-layer reaction fuses individual layers into an integrity, thus eliminating layer delamination induced by FDM, offering isotropic mechanical properties regardless of the printing orientations. The highly cross-linked network provides outstanding mechanical strength and superb thermal stability. The excellent shape memory performance with fast recovery rate and large recovery degree is also obtained in the three-dimensional (3D) printed composites.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

3D Printing of Liquid Crystal Elastomer Foams for Enhanced Energy Dissipation Under Mechanical Insult

Polymer foams are an essential class of lightweight materials used to protect assets against mechanical insults, such as shock and vibration. Two features are important to enhance their energy absorption characteristics: the foam structure and the matrix phase mechanical behavior. This study investigates novel approaches to control both of these features to enhance the energy absorption capability of flexible lattice foams. First, we consider 3D printing via digital light processing (DLP) as a method to control the foam mesostructure across a suite of periodic unit cells. Second, we introduce an additional energy dissipation mechanism in the solid matrix phase material by 3D printing the lattice foams with polydomain liquid crystal elastomer (LCE), which undergo a mechanically induced phase transition under large strains. This phase transition is associated with LC mesogen rotation and alignment and provides a second mechanism for mechanical energy dissipation in addition to the viscoelastic relaxation of the polymer network. Here, we contrast the 3D printed LCE lattices with conventional, thermomechanically near-equivalent elastomer lattice foams to quantify the energy-absorbing enhancement the LCE matrix phase provides. Under cyclic quasi-static uniaxial compression conditions, the LCE lattices show dramatically enhanced energy dissipation in uniaxial compression compared to the non-LCE equivalent foams printed with a commercially available photocurable elastomer resin. The lattice geometry also plays a prominent role in determining the energy dissipation ratio between the LCE and non-LCE foams. We show that when increasing the lattice connectivity, the foam deformation transitions from bending-dominated to stretching-dominated deformations, which generates higher axial strains in the struts and higher energy dissipation in the lattice foam, as stretching allows greater mesogen rotation than bending. The LCE foams demonstrate superior energy absorption during the repeated dynamic loading during drop testing compared with the non-LCE equivalent foams, demonstrating the potential of LCEs to enhance physical protection systems against mechanical impact.

3D printing↗
DOE OSTI2022

Mechanically and Thermally Enhanced 3D-Printed Photocurable Polymer Nanocomposites Containing Functionalized Chitin Nanowhiskers by Stereolithography

Additive manufacturing, or simply 3D printing (3DP), where objects are built through layer-wise material deposition, has gained significant academic and industrial attention as a result of the development of advanced and functional materials requiring rapid, customized, and flexible solutions. In the context of green manufacturing, diversifying environmentally and economically sustainable material portfolios is an essential endeavor for the success of 3DP technology that uses widely available, highly valuable, and renewable materials. Here, we used stereolithography (SLA) for processing methacrylate-based photocurable resins containing crab shell-derived chitin nanowhiskers (CNWs), which are surface-functionalized by reactive acrylate groups. Results from full spectral, thermal, structural, and topological analyses corroborate not only the surface functionalization of CNWs but also indicate the presence of these photocurable CNW (pCNW) fillers in the 3D-printed nanocomposites. Owing to the strong interfacial bond induced by the physical and chemical crosslinking between the pCNW and methacrylate (MA) polymer matrix, the internally formulated nanocomposites displayed enhanced thermomechanical properties (e.g., storage modulus and glass transition temperature) compared to those of commercially available pure SLA resins. For instance, the inclusion of 0.5 wt % pCNW improved the tensile strength and stiffness to up to 78 and 71%, respectively, without compromising the toughness and ductility of the printed material. Accordingly, this result also evidences the compatibility between the filler and resin materials. Consequently, the formation of a crosslinked network in the nanocomposite structure results in a higher thermal stability and activation energy (i.e., up to ~79%) for all the hybrid materials than the pristine MA. Finally, the high-resolution SLA print features, dimensional accuracy, and enhanced mechanical performance of our microstructure-forming functionalized chitin-based nanocomposites make them promising materials for a wide range of robust and high-performance industrial applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D Printing of Functional Hydrogel Devices for Screenings of Membrane Permeability and Selectivity

Developing a fundamental understanding of the effects of varying ligand chemistries on mass transport rates is key to designing membranes with solute-specific selectivity. While permeation cells offer a robust method to characterize membrane performance, they are limited to assessing a single membrane chemistry or salt solution per test. As a result, investigating the effects of varying ligand chemistries on membrane performance can be a tedious process, involving both the preparation of multiple samples and numerous, time-consuming permeation tests. This study uses digital light processing (DLP) 3D printing to fabricate a millifluidic flow-based permeation device made from a hydrogel active ester network that can be easily functionalized with ion-selective ligands. Without the need for bonding or assembly steps, ligands can be introduced and tested in the permeation device by simply injecting a small volume of a ligand solution. Various salt concentrations and molecular species can be cycled through a single device by switching the solution feeding into the salt reservoir, thereby reducing the number of samples needed for permeability and selectivity screenings. This research sets the groundwork for formulation development and postprocessing methods to 3D-print functional millifluidic devices capable of assessing solute selectivity in membranes and polymer adsorbents for aqueous separations. In this work, comparable salt permeability trends were observed with both 3D-printed devices and traditional assays. Devices were functionalized with an imidazole ligand to investigate salt permeability and selectivity of monovalent and divalent salts. Measurements showed increasing permeability for monovalent salts (NaCl) relative to divalent salts (MgCl 2 , CuCl 2 ) in functionalized membranes, with higher monovalent/divalent selectivity at increasing imidazole grafting densities. Here, the methods and findings described here represent a step toward developing higher-throughput methods with 3D-printed devices for screening the effects of ligand chemistry on mass transport rates in membrane materials.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Metamodels for Rapid Analysis of Large Sets of Building Designs for Robotic Constructability: Technology Demonstration Using the NASA 3D Printed Mars Habitat Challenge

Disruptive robotic construction technologies such as additive deposition of cementitious materials like concrete (or "3D concrete printing") require the synchronous operation of multiple pieces of equipment in the production setup. In such an environment, it is crucial to simulate the robotic motions (for toolpath clashes) and the cementitious material behavior (for toolpath failures) to ensure fail-proof constructability of the envisioned building geometry. However, toolpath clash detection requires 4D simulations of the production setup, which are computationally graphics intensive, whereas toolpath failure detection requires actual 3D printing of test parts from the geometry to identify areas prone to failure while 3D printing, which is physically tedious. Both these processes, being computationally and physically intensive, have largely curtailed designers from simulating and exploring large sets of design options with varying geometries and toolpath configurations. To overcome this and allow designers to explore large sets of design possibilities, this paper proposes two novel computational metamodels capable of performing robotic toolpath clash detection and failure detection with significantly reduced times than the earlier approaches. The developed metamodels were used to rapidly simulate large sets of building design options for robotic constructability in the NASA 3D-Printed Mars Habitat Challenge.

clash detection↗
DOE OSTI2020

Mixed-flow design for microfluidic printing of two-component polymer semiconductor systems

The rational creation of two-component conjugated polymer systems with high levels of phase purity in each component is challenging but crucial for realizing printed soft-matter electronics. Here, we report a mixed-flow microfluidic printing (MFMP) approach for two-component π -polymer systems that significantly elevates phase purity in bulk-heterojunction solar cells and thin-film transistors. MFMP integrates laminar and extensional flows using a specially microstructured shear blade, designed with fluid flow simulation tools to tune the flow patterns and induce shear, stretch, and pushout effects. This optimizes polymer conformation and semiconducting blend order as assessed by atomic force microscopy (AFM), transmission electron microscopy (TEM), grazing incidence wide-angle X-ray scattering (GIWAXS), resonant soft X-ray scattering (R-SoXS), photovoltaic response, and field effect mobility. For printed all-polymer (poly[(5,6-difluoro-2-octyl-2H-benzotriazole-4,7-diyl)-2,5-thiophenediyl[4,8-bis[5-(2-hexyldecyl)-2-thienyl]benzo[1,2-b:4,5-b′]dithiophene-2,6-diyl]-2,5-thiophenediyl]) [J51]:(poly{[N,N′-bis(2-octyldodecyl)naphthalene-1,4,5,8-bis(dicarboximide)-2,6-diyl]-alt-5,5′-(2,2′-bithiophene)}) [N2200]) solar cells, this approach enhances short-circuit currents and fill factors, with power conversion efficiency increasing from 5.20% for conventional blade coating to 7.80% for MFMP. Moreover, the performance of mixed polymer ambipolar [poly(3-hexylthiophene-2,5-diyl) (P3HT):N2200] and semiconducting:insulating polymer unipolar (N2200:polystyrene) transistors is similarly enhanced, underscoring versatility for two-component π -polymer systems. Mixed-flow designs offer modalities for achieving high-performance organic optoelectronics via innovative printing methodologies.

42 ENGINEERING↗
DOE OSTI2022

Direct ink write multi-material printing of PDMS-BTO composites with MWCNT electrodes for flexible force sensors

Here, with recent advances of additive manufacturing technology, direct ink write (DIW) printing has allowed to incorporate multi-material printing of various materials with freedom of design and complex geometric shapes to complete functional sensors in a one-step fabrication. This paper introduces the use of DIW 3D printing of polydimethylsiloxane (PDMS) with barium titanate (BTO) filler as stretchable composites with tunable piezoelectric properties that can be used for force sensors applications. To improve the bonding between stretchable piezoelectric composites and electrodes, multi-walled carbon nanotubes was included in the fabrication of electrodes at a fixed ratio of 11 wt. %. The alignment of the BTO dipoles was achieved through corona poling method, which applies an electric charge on the surface layer of the functional material, aligning the dipoles in the desired direction and thus gaining the piezoelectricity. Different BTO mixing ratios (10–50 wt. %) were evaluated in order to obtain tunable piezoelectric properties and compare the sensitivity with respect their elastic properties. Tensile testing and piezoelectric testing were carried out to characterize mechanical and piezoelectric properties. Results showed that fabricated PDMS with 50 wt. % BTO gave the highest piezoelectric coefficient (d 33 ) of 11.5 pC N -1 and with an output voltage of 385 mV under compression loading of >200 lbF. This demonstrates feasibility of using multi-material DIW printing to fabricate piezoelectric force sensors with integrated electrodes in one-step without compromising the flexibility of the material.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Recent developments in 3D-printed membranes for water desalination

The recognition of membrane separations as a vital technology platform for enhancing the efficiency of separation processes has been steadily increasing. Concurrently, 3D printing has emerged as an innovative approach to fabricating reverse osmosis membranes for water desalination and treatment purposes. This method provides a high degree of control over membrane chemistry and structural properties. In particular, when compared to traditional manufacturing techniques, 3D printing holds the potential to expedite customization, a feat that is typically achieved through conventional manufacturing methods but often involves numerous processes and significant costs. This review aims to present the current advancements in membrane manufacturing technology specifically tailored for water desalination purposes, with a particular focus on the development of 3D-printed membranes. A comprehensive analysis of recent progress in 3D-printed membranes is provided. However, conducting experimental work to investigate various influential factors while ensuring consistent results poses a significant challenge. To address this, we explore how membrane manufacturing processes and performance can be effectively pre-designed and guided through the use of molecular dynamics simulations. Finally, this review outlines the challenges faced and presents future perspectives to shed light on research directions for optimizing membrane manufacturing processes and achieving optimal membrane performance.

3D printing membranes↗
DOE OSTI2022

Characterization of Properties of Laser Powder Bed Fusion 3D-Printed Inconel 718 for Centrifugal Turbomachinery Applications

Here, this paper presents the results of a comprehensive effort to characterize the properties of Inconel 718 produced by a form of laser powder bed fusion (LPBF) additive manufacturing (AM) or 3D-printing, subsequently subjected to hot isostatic pressing (HIP) and heat treatment according to standards F3055-14a and AMS 5663, respectively. Material property data, while broadly available for traditional Inconel 718 presentations (e.g. forgings or castings), is currently lacking for the 3D-printed material. It is expected that while limited in size, the experimental data sets presented provide sufficient information to glean the capability of LPBF Inconel 718. These include: 1) Chemical composition, electron backscatter diffraction (EBSD), and x-ray energy dispersive spectroscopy (XEDS) characterization of 3D-printed material structure; 2) Tensile properties — 0.2% yield stress, ultimate stress, modulus of elasticity, and elongation to failure — based on 108 samples, as functions of temperature and sample print orientation; 3) Creep rupture data including the Larson-Miller parameter, based on 21 samples; and 4) High cycle fatigue data based on 21 samples as a function of temperature. Results are compared to available standards and/or data for forged, cast, and other AM Inconel 718. A key observation of this study, based on the EBSD results, is that while the material appears to approach full recrystallization following heat treatment, there is a detectable fraction of the material that does not fully recrystallize, resulting in a material with mechanical properties (e.g. yield stress, creep rupture) measurably lower than those of forgings, but higher than those of castings.

30 DIRECT ENERGY CONVERSION↗