Search NASA⌕ Search

SEARCH · Search NASA

Results for “processing parameters”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Laser damage of crazed electron-beam high-reflectors following infrared and ultraviolet irradiation in the nanosecond pulse regime

Laser damage of optical components can be a limiting factor in scaling the energetics of high-peak and average power laser systems. Specifically for optical coatings, damage under nanosecond pulsed irradiation is initiated by pre-existing defects in the coating layers, including those that cause discontinuities in the structure, like craze lines. Crazing or cracking in a multilayer dielectric optical coating is induced when the overall coating stress is sufficiently tensile, and is an occasionally observed issue when employing more porous deposition techniques like electron-beam evaporation. Here, in this study, electron-beam high-reflectors were fabricated utilizing process parameters that are known to induce crazing based on prior processing history to systematically evaluate the impact of crazing on reflector damage performance for 1064 and 355 nm lasers. The crazing that was observed was apparently nucleated at nodular defects. When the cross-section of these nodules was investigated, it was observed that there were cracks into the fused silica substrate of approximately 5 µm in depth. The craze lines were irradiated with 1064 and 355 nm light at fluences slightly above the onset of damage initiation fluence of the coating. The 1064 nm irradiated sub-apertures exhibit laser damage but with no spatial correlation with the craze line, whereas the 355 nm irradiated area exhibited many damage sites along the craze line. Finite-difference time-domain electric-field simulations were conducted, and ∼2× field amplification in hafnia was observed for the 355 nm wavelength case. The laser damage can be attributed to a slight electric-field intensification coincidental with an area where UV damage-prone precursors are known to occur. The 355 nm laser damage in uncoated fused silica substrates has been previously correlated to initiate through localized UV absorption at the broken silica bonds in the tips of fractures.

Harthcock, Colin [Lawrence Livermore National Labo↗
DOE OSTI2021

Model-informed, Adaptive Physical Vapor Deposition to Fabricate Hierarchical Binary-alloy Thin-films

Designing next generation thin films, tailor-made for specific applications, relies on the availability of robust processing-structure-property relationships. Traditional structure zone diagrams are limited to low-dimensional mappings, with machine-learning methods only recently attempting to relate multiple processing parameters to the final microstructure. Despite this progress, structure-processing relationships are unknown for processing conditions that vary during thin-film deposition, limiting the range of microstructures and properties achievable. In this project, we employed a phase-field computational model combined with a genetic algorithm (GA) to identify and design time-dependent processing protocols that achieve tailor-made microstructures. We simulate the physical vapor deposition of a binary-alloy thin film by employing a phase-field model, where deposition rates and diffusivities are controlled via the genetic algorithm. Our GA-guided protocols achieve targeted microstructures with lateral and vertical concentration modulations, as well as more complex, hierarchical microstructures previously not described in simple structure zone diagrams. Our algorithm provides insight to experimentalists looking for additional avenues to design novel thin-film microstructures.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Novel and effective surface passivation for high efficiency n- and p-type Silicon solar cell

The project objective was to develop a novel Si surface passivation method using chalcogens, sulfur (S) and/or selenium (Se), as passivating elements, to withstand industry-standard high temperature contacting and metallization schemes for p-type Si based passivated emitter and rear contact (p-PERC) solar cells. The back surface passivation of PERC cells has been improved drastically with the invention and successful application of an Al 2 O 3 passivation layer. However, the front n + diffused junction surface is still poorly passivated by the standard amorphous silicon nitride (SiNx) anti-reflection coating (ARC) layer. This project sought to address the passivation challenges of both front n+ emitter and undiffused p-Si back surface. Improved p-PERC solar cell performance with open circuit voltage (V OC ) > 680 mV and efficiency of 22% were targeted to validate superior defect passivation properties as compared to standard SiO 2 / Al 2 O 3 passivation. During this project, we systematically investigated process-structure-properties-performance relationships of this novel advanced defect passivation approach. The S/Se passivation was carried out by reacting industrial Czochralski (Cz) Si wafers in H 2 S and H 2 Se gases in a chemical vapor deposition (CVD) reactor at temperatures up to 700°C. After an exhaustive optimization of the process parameters (temperature, time, and gas concentration), we established an optimized process and demonstrated extremely low surface recombination velocities (SRVs) of 1.5 cm/s and 8 cm/s on n-type and p-type Si, respectively, by S-passivation. In-depth surface and interface characterization were performed using soft x-ray and photoelectron spectroscopies (XPS, UPS, XES), combined with capacitance-voltage-frequency (C-V-f) measurements, to decipher the surface chemical/electronic structure and interface defect state densities. These measurements provided critical understanding of the defect passivation mechanism and elucidated the presence of surface S-Si bonds, a reduction of surface dipoles, and low interface state densities (D it ) < 10 11 cm -2 ev -1 . We also found that the Se-passivation is inferior to the S-passivation (by at least one order of magnitude in SRV). Application of the optimized S-passivation to the n+ diffused emitter surface led to a low surface recombination current density, J0 ≈ 40 fA/cm 2 (~ 1/4 of the industry-standard SiNx-passivation), and high implied V OC (686 mV) in p-PERC solar cell structures. The S-passivation process also was found to improve the bulk quality of the p-type Si, better than the SiO 2 or Al 2 O 3 passivation processes. After successful demonstration of efficient passivation of Si surface defects by S, we extensively studied the air, thermal, and illumination stability of the passivation structure. S-passivation itself degrades in air due to competing reactions with moisture and oxygen to form oxides, which can be eliminated by a SiNx capping layer (also acting as a anti-reflective coating). After SiNx process optimization, we demonstrated illumination and thermally stable S-passivation with SRV < 5 cm/s and J 0 < 80 fA/cm 2 . These enhancements in Si passivation, incorporated into p-PERC cells, achieved an efficiency of 19.93% with V OC = 649 mV, using manufacturing metallization and contacting schemes. The low cell performance (cell V OC is much less than the implied V OC = 686 mV, anticipated from surface passivation) was identified due to degradation of S-passivation during the metal firing step (out-diffusion of S from the Si interface to the SiNx surface). The S-passivation of Si surfaces shows significant promise with excellent passivation quality, essential for high performance (high V OC , high efficiency) solar cells. Integration of this innovative defect passivation into devices, however, demands further development of the capping layer, low temperature (<700°C) metallization process, and/or engineering of advanced device structures. Surface passivation-dominated advanced Si solar cells, such as tunnel oxide passivated contacts and Si heterojunctions, are increasingly of interest due to their high-performance potential and will have a growing photovoltaic market share in the near future.

14 SOLAR ENERGY↗
DOE OSTI2023

Data Archive and Portal (DAP) Platform for Solid Phase Processing Technologies

The scale and speed of data generated by modern scientific experiments have constantly challenged the research community to store, curate, manage and optimally use it to drive scientific discoveries. In this work, we have developed a data archive and portal (DAP) platform including analytics capabilities to collect, curate, and manage data and metadata stream for solid phase processing (SPP) techniques. We successfully hosted around ~347K files of data related to processing parameters, microscopic images, and spectroscopic data related to solid phase processing. The DAP platform for SPP will establish an enduring capability to support machine learning and grow collaboration at the intersection of materials science and data science.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Manufacturing Dissolvable Alloy Components using ShAPE: A Study on Solid Phase Processing of Mg-W Composites and WJ11 Alloys

Dissolvable alloys and composites are an emerging class of materials that demonstrate tailored sorptivity in corrosive environments. This work explored the viability of solid phase processing (SPP) techniques, namely the shear assisted processing and extrusion (ShAPETM) method, to manufacture dissolvable magnesium composites and alloys components such as rods and tubes. The study also determined the effects of material composition and manufacturing process conditions on material microstructures developed during SPP and the resulting performance of the components. Explicit properties of interest included ultimate tensile strength, ultimate compressive strength, and yield strength. The application fields of interest for dissolvable alloys were identified as oil-and-gas operations and biomedical implants. Accordingly, PNNL collaborated with industrial and academia partners, Fortek Industries, Houston and University of Pittsburgh, during the course of this project for material and ShAPE process development. PNNL determined the viability of the using ShAPE to process the custom-designed materials provided by the project partners. This was done by identifying process parameters such as tool rotation rate, tool plunge rate, and process cooling optimal for manufacturing components with consolidated microstructures. Subsequently, PNNL also performed microstructural characterization on unprocessed and processed samples and mechanical property testing. One of the major findings from this work is that ShAPE was able to manufacture dissolvable magnesium composite and alloy rods and tubes with consolidated homogeneous microstructures and minimal macroscale defects on component surfaces. It was observed that samples processed via ShAPE demonstrated an average grain size < 2 - 5 µm, which was markedly lower than that of the precursors with 8 – 13 µm grains. Results showed that the ShAPE synthesized dissolvable magnesium composite and alloy strength was on par with or better than those components that were manufactured using traditional manufacturing processes such as forging and extrusion. It is noteworthy that the ShAPE samples were made with considerably lower number of process steps.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Atmosphere Effects in Laser Powder Bed Fusion: A Review

The use of components fabricated by laser powder bed fusion (LPBF) requires the development of processing parameters that can produce high-quality material. Manipulating the most commonly identified critical build parameters (e.g., laser power, laser scan speed, and layer thickness) on LPBF equipment can generate acceptable parts for established materials and moderately intricate part geometries. The need to fabricate increasingly complex parts from unique materials drives the limited research into LPBF process control using underutilized parameters, such as atmosphere composition and pressure. As presented in this review, manipulating atmosphere composition and pressure in laser beam welding has been shown to expand processing windows and produce higher-quality welds. The similarities between laser beam welding and laser-based AM processes suggest that this atmosphere control research could be effectively adapted for LPBF, an area that has not been widely explored. Tailoring this research for LPBF has significant potential to reveal novel processing regimes. This review presents the current state of the art in atmosphere research for laser beam welding and LPBF, with a focus on studies exploring cover gas composition and pressure, and concludes with an outlook on future LPBF atmosphere control systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Manufacturing ODS Steels from GARS Powders by Friction Consolidation and Extrusion

Previous research suggested that friction-based processing is a promising method for fabricating oxide dispersion-strengthened (ODS) steel. In this study, we combined friction consolidation and friction extrusion to successfully manufacture ODS steel rods using precursor powder made with gas atomization reaction synthesis. We examined the microstructure evolution from the initial powder to the final extruded rod, which revealed the dispersion process of Y. Additionally, by comparing the microstructures of three rods extruded at different temperatures, we showed that low-temperature friction extrusion effectively enhanced microstructure uniformity and prevented grain coarsening, leading to improved mechanical properties. Furthermore, our findings provide practical guidelines for adjusting processing parameters in the production of ODS steel using friction-based processing.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Characterization of MoS 2 films via simultaneous grazing incidence X-ray diffraction and grazing incidence X-ray fluorescence (GIXRD/GIXRF)

Physical vapor deposited (PVD) molybdenum disulfide (nominal composition MoS 2 ) is employed as a thin film solid lubricant for extreme environments where liquid lubricants are not viable. The tribological properties of MoS 2 are highly dependent on morphological attributes such as film thickness, orientation, crystallinity, film density, and stoichiometry. These structural characteristics are controlled by tuning the PVD process parameters, yet undesirable alterations in the structure often occur due to process variations between deposition runs. Nondestructive film diagnostics can enable improved yield and serve as a means of tuning a deposition process, thus enabling quality control and materials exploration. Grazing incidence X-ray diffraction (GIXRD) for MoS 2 film characterization provides valuable information about film density and grain orientation (texture). However, the determination of film stoichiometry can only be indirectly inferred via GIXRD. The combination of density and microstructure via GIXRD with chemical composition via grazing incidence X-ray fluorescence (GIXRF) enables the isolation and decoupling of film density, composition, and microstructure and their ultimate impact on film layer thickness, thereby improving coating thickness predictions via X-ray fluorescence. We have augmented an existing GIXRD instrument with an additional X-ray detector for the simultaneous measurement of energy-dispersive X-ray fluorescence spectra during the GIXRD analysis. This combined GIXRD/GIXRF analysis has proven synergetic for correlating chemical composition to the structural aspects of MoS 2 films provided by GIXRD. We present the usefulness of the combined diagnostic technique via exemplar MoS 2 film samples and provide a discussion regarding data extraction techniques of grazing angle series measurements.

MoS2↗
DOE OSTI2026

Rapid Characterization Tools for Process Optimization: Cooperative Research and Development (Final Report)

In this project Prenexus Health, Inc. (Prenexus) and NLR will develop rapid characterization tools to improve the Prenexus production process. First, we will develop a tool to predict the overall performance of the Prenexus manufacturing process converting high-fiber sugarcane to xylo-oligosaccharides (XOS) (both the overall process yield and the composition of the XOS product) using rapid characterization of the incoming feedstock and knowledge of key process parameters. This tool will dramatically increase Prenexus’ understanding of the overall process. Second, we will develop a tool to predict the concentration of soluble oligomeric and monomeric xylose and organic acids in multiple process streams at-line in the Prenexus process, enabling real-time process control of the conversion process.

09 BIOMASS FUELS↗
DOE OSTI2026

Comparative Evaluation of Spectral Methods for Robust Reactor Noise Estimation

Reactor noise analysis provides a noninvasive means to determine neutron kinetic parameters from stochastic fluctuations in detector signals. However, standard cross-power spectral density (CPSD) analyses can be sensitive to numerical processing choices, which may introduce processing-dependent systematic shifts in estimates of the prompt neutron decay constant (α) and limit reproducibility. This study uses a hybrid multitaper–Welch spectral estimator to analyze subcritical noise measurements from a fast-spectrum critical assembly. The decay constant α was extracted using three frequency-domain methods: the CPSD, the magnitude-squared coherence (MSC), and the generalized magnitude-squared coherence (GMSC). These coherence-based estimators normalize detector auto-spectral structure and are expected to reduce the sensitivity of fitted α values to processing parameters. A Sobol global sensitivity analysis identified which numerical inputs most strongly influence the fitted values of α. All estimators produced a linear dependence of α on inverse count rate, with delayed-critical extrapolations near 1.7 × 10 4 s −1 , in agreement within 8% of MCNP6.3 KOPTS benchmark calculations. Sensitivity results show that while the CPSD depends on both time-bin width and taper selection, the MSC and GMSC are dominated by time-bin width alone, indicating reduced parameter coupling and greater robustness to processing variability. These findings demonstrate the feasibility and practical value of coherence-based spectral estimators for extracting α from reactor noise and support their broader application to multi-detector and irregular datasets in subcritical system characterization.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2021

An Abrasive Wear Model of Knife Milling to Predict the Impact of Material Properties and Milling Parameters on Knife Edge Recession

A workable analytical abrasion model that relates critical knife-mill process parameters (geometry and rotational speed) to critical material attributes of inorganic mineral species in feedstock (density, size, and aspect ratio) and substrate (hardness and elastic modulus) was formulated to model wear of knives in knife-milling systems. Results of the model were compared to experimental observations of the edge recession of knives used in a knife mill marketed by Eberbach. Results showed good agreement between the predicted and measured shape of a worn knife and showed that a quality-by-design approach can be developed to predict component reliability based on scientific engineering principles in lieu of trial-and-error approaches.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Scan strategies in EBM-printed IN718 and the physics of bulk 3D microstructure development

Three-dimensional (3D) characterization provides opportunities for understanding processing-structure relationships in additively manufactured (AM) materials. Bulk samples of Inconel 718 were fabricated via electron beam melting (EBM) in order to study microstructural development as a function of energy input and beam scan strategy. TriBeam tomography of bulk Inconel 718 microstructures built under steady-state growth conditions reveals the sensitivity of microstructure formation and evolution to machine process parameters. Here, samples manufactured using a narrow range of energy input per unit build area result in varied grain morphologies and crystallographic textures. Using TRUCHAS, a thermal simulation software, the thermal history of bulk scan strategies was predicted, and combined with a calibrated microstructure-processing map to accurately predict bulk grain morphologies. The solidification parameters and the 3D measured nucleation density are used to predict the transition between columnar and equiaxed grain morphologies, providing a process map to guide AM parameter choices to locally control as-printed microstructure. A two-dimensional metric for characterizing bulk grain morphology was also found to agree well with predictions from the process map calibrated by 3D data. Combined with 3D tomography and thermal modelling, the physics of structure development were understood at a new level of detail with respect to the competing processes of grain nucleation and epitaxial growth.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Formation of uranium oxy-carbide and uranium carbide via conversion of polymer covered uranium dioxide by laser-based thermal processing

Conventional formation of carbonaceous uranium compounds requires bulk processing using furnace-based approaches. Here, a methodology employing polymer covered uranium dioxide and laser-based heating is explored to enable rapid, localized formation of carbonaceous uranium compounds. Specifically, heating of poly(methyl methacrylate) covered uranium dioxide powder to high temperatures using laser irradiation in argon and methane gaseous environments was investigated. Decomposition of material and reactions induced by laser irradiation were probed in situ by residual gas analysis using a benchtop mass spectrometer. In this study, to determine the effect on the resultant material phase, three different process parameters were varied: gaseous atmosphere, laser power, and laser irradiation time. Material processed under varying conditions was analyzed using powder X-ray diffraction and scanning electron microscopy. This work realized the conversion of uranium dioxide into uranium oxy-carbide(s) and uranium carbide(s) phases, at over 60 wt.%, via the polymer surface application and laser-based thermal decomposition methodology.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Li-ion battery design through microstructural optimization using generative AI

Lithium-ion batteries are used across various applications, necessitating tailored cell designs to enhance performance. Optimizing electrode manufacturing parameters is a key route to achieving this, as these parameters directly influence the microstructure and performance of the cells. However, linking process parameters to performance is complex, and experimental or modeling campaigns are often slow and expensive. This study introduces a fast computational optimization framework for electrode manufacturing parameters. A generative model, trained on a small dataset of microstructural images associated with different manufacturing parameters, efficiently generates representative microstructures for new parameters. This model is integrated into a Bayesian optimization loop that includes microstructure generation, characterization, and simulation, aiming to find optimal manufacturing parameters for a particular application. Significant improvement in the energy density of a 4680 cell is achieved through bespoke cell design, highlighting the importance of cell-scale normalization. The framework’s modularity allows its application to various advanced materials manufacturing scenarios.

batteries↗
DOE OSTI2023

Remarkable enhancement in thermal conductivity of stainless-steel leveraging metal composite via laser powder bed fusion: 316L-Cu composite

This work aimed to significantly enhance the thermal conductivity of the SS matrix by fabricating a metal composite SS-Cu system utilizing a laser powder bed fusion process. The impact of process parameters on the microstructure of SS-Cu samples is investigated. Here, the processing and post-processing factors that influence the effective thermal conductivity of the metal composite SS-Cu system are discussed. Then, the effective thermal conductivity and mechanical properties of the SS-Cu composite are measured at room temperature and operating temperature of 300 °C. The optimized laser powder bed fusion parameters led to low Marangoni convection, high cooling rate, greater macro-segregation, and higher thermal conductivity values albeit at the cost of ductility in SS-Cu metal composite likely due to the presence of the unmelted powder particles. As-printed SS-60 vol % Cu and annealed SS-60 vol % Cu had 2.5X and 6.6X thermal conductivity enhancement, respectively. During annealing, phase separation, partial melting of Cu, and formation of a continuous network of Cu surrounding SS play a key role in enhancing the thermal conductivity of the SS-Cu metal composite structure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterization of the Fusion Zone in Laser Beam Welds on SS304L

Designing a welded joint requires consideration of the welding process, component/assembly structure and weld geometry, material composition, properties, and desired joint performance. The designer must also specify a set of acceptance criteria used to evaluate the welds. This study was conducted to support the design team responsible for specifying the spot weld profile by investigating the relationship between weld process parameters and the weld geometry and properties to further inform design optimization. The subjects of this study are two thin stainless steel 304L (SS304L) components joined by Laser Beam Welding (LBW). The components are the Housing, which contains flexible circuitry, and the Cover that protects the circuitry during handling, installation, and under service loads. Figure 1 illustrates coupon versions of the Cover and Housing used to simulate the interface between these components for weld testing. These coupon representations of assembly components were designed to match the material and relevant geometry related to the welded joint while other features not relevant to the welded joint are excluded.The objective of this study was to characterize the sensitivity of the weld geometry and mechanical properties to the input weld parameters to inform further Finite Element Analysis (FEA) efforts in balancing joint strength against assembly deformation caused by the welding process. Characterization was accomplished by varying laser welding parameters around the current design values and measuring weld geometry on the cross-sections. Nanoindentation with a spherical and flat-ended tip was used on polished section cuts of the weld to obtain direct estimates of the stress-strain response of the Fusion Zone (FZ) for comparison to the Base Metal (BM).

42 ENGINEERING↗
DOE OSTI2020

Rheological behavior of neat and carbon fiber-reinforced poly(ether ketone ketone) for extrusion deposition additive manufacturing

To develop new materials for extrusion additive manufacturing (AM) systems, a fundamental understanding of rheological properties is essential to correlate the effect of processing on material structure and its properties. In this work, the rheological properties of five different grades of neat and carbon fiber (CF)-reinforced poly(ether ketone ketone) are reported. Rheological properties are essential to understand the effect of reinforcing fibers and AM process parameters such as time, temperature, environment, and shear rate on flow behavior during processing. Small-amplitude oscillatory shear tests and steady shear tests indicated neat grades to exhibit less increase in viscosity over time when processed in air than the CF-filled grades. The filled grades showed greater shear thinning and lower sensitivity to temperature. Altogether, this rheological analysis provides a broad framework for determining appropriate processing conditions for extrusion deposition AM of such high-temperature polymer systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

A review on the sizing and selection of control valves for thermal hydraulics for reactor system applications

This study presents an overview regarding how to model/size, choose, and maintain control valves (CVs) for a reactor system thermal hydraulics experimentation—specifically simulating pipe break(s) and a loss of coolant accident (LOCA) analysis. In a thermal hydraulics test loop, CVs modulate fluid flow according to the control signal generated by the controller to control the process parameter. The selection of a CV in industrial applications involves many factors, including process diversity, safety, and reliability. Further, the key issues and challenges for performing proper mathematical modeling, installation, servicing, and calibration are also discussed for the benefit of operators and end-users. Additionally, this research includes case studies illustrating major plant-level accidents associated with the malfunctioning of valves. Therefore, the study will serve as a knowledge base or reference guide for young professionals and operators who wish to better understand process control applications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗