SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The corrugated horn is discussed as is a valuable tool for use in microwave pattern ranges. It has the properties of concentrated energy in the main beam, low backlobes, high efficiency, almost monotonic amplitude, and phase radiation patterns which make the corrugated horn useful for a source antenna in a pattern range and also as a possible standard antenna for calibration purposes.
The implementation of a moment method code for the analysis of horn antennas was accomplished. The code can analyze the antenna with or without lossy material coatings. It predicts the antenna gain, voltage standing wave ratio (VSWR) on the feeding waveguide, the existing modes on the radiating aperture, and radiation patterns of the antenna. Many computations were performed on three pyramidal horn antennas, and their radiation and VSWR's are presented and compared with experimental data. Although the code is still being finalized, some discussions on using the code are included.
Computing zenith antenna temperature from antenna radiation patterns and antenna environment brightness temperatures
The radiation pattern of a line source is calculated for the case in which the source is lying on the top or the bottom surface of a lossless dielectric substrate that is mounted on the top of semiinfinite dielectric medium. It is found that in both cases the pattern along the interfaces has a null; that the pattern in the upper semiinfinite medium has a single lobe; and that the pattern in the lower semiinfinite medium has many lobes, the number of which varies with the substrate thickness. In both cases, the power radiated into the lower medium is more than that radiated into the upper medium. Applications of this calculation to remote sensing, microstrip antenna technology, and antenna arrays are discussed.
A 64-element, 30-GHz microstrip antenna array with corporate feed network was designed and built on a 0.254-mm (10-mil) thick lanthanum aluminate substrate. One antenna pattern was fabricated from gold film, and a second pattern used TlCaBaCuO high-temperature superconductor. Both antennas used gold ground planes deposited on the reverse side of the substrate. Gain and radiation patterns were measured for both antennas at room temperature and at cryogenic temperatures. Observations agree well with simple models for loss and microwave beam width, with a gain on boresight of 20.3 dB and beam width of 15 deg for the superconducting antenna. The antenna loss is only 1.9 dB.
We present a new study of jet interactions in the quark-gluon plasma created in high-energy heavy-ion collisions, using a multistage event generator within the jetscape framework. We focus on medium-induced modifications in the rate of inclusive jets and high transverse momentum (high-p T ) hadrons. Scattering-induced jet energy loss is calculated in two stages: a high virtuality stage based on the matter model, in which scattering of highly virtual partons modifies the vacuum radiation pattern, and a second stage at lower jet virtuality based on the LBT model, in which leading partons gain and lose virtuality by scattering and radiation. Coherence effects that reduce the medium-induced emission rate in the matter phase are also included. The TRENTO model is used for initial conditions, and the (2 + 1)dimensional VISHNU model is used for viscous hydrodynamic evolution. Jet interactions with the medium are modeled via 2-to-2 scattering with Debye screened potentials, in which the recoiling partons are tracked, hadronized, and included in the jet clustering. Holes left in the medium are also tracked and subtracted to conserve transverse momentum. Calculations of the nuclear modification factor (R AA ) for inclusive jets and high-p T hadrons are compared to experimental measurements at the BNL Relativistic Heavy Ion Collider (RHIC) and the CERN Large Hadron Collider (LHC). Within this framework, we find that with one extra parameter which codifies the transition between stages of jet modification—along with the typical parameters such as the coupling in the medium, the start and stop criteria, etc.—we can describe these data at all energies for central and semicentral collisions without a rescaling of the jet transport coefficient q.
A general tradeoff is made of the symmetric Cassegrain antenna with regard to the possibility of meeting a 90% beam efficiency. The effects of aperture taper and blockage are calculated using an adjustable sidelobe circular distribution. Numerical integration is used. For the feed spillover calculation, a low sidelobe symmetric feed pattern is used with the equivalent parabola and numerical integration. Reflector cross polarization is calculated using double numerical integration. Reflector back lobes are estimated from radiation pattern envelopes of commercial common carrier dish antennas. The curves allow a range of f/D to be determined for a specified edge taper and blockage diameter ratio, and with a table of Cassegrain parameters, a range of possible designs that meet the 90% beam efficiency is obtained. It is shown that the feed and reflector design and implementation must be carefully done.
A Moment Method Model for the radiation pattern characterization of single Linearly Tapered Slot Antennas (LTSA) in air or on a dielectric substrate is developed. This characterization consists of: (1) finding the radiated far-fields of the antenna; (2) determining the E-Plane and H-Plane beamwidths and sidelobe levels; and (3) determining the D-Plane beamwidth and cross polarization levels, as antenna parameters length, height, taper angle, substrate thickness, and the relative substrate permittivity vary. The LTSA geometry does not lend itself to analytical solution with the given parameter ranges. Therefore, a computer modeling scheme and a code are necessary to analyze the problem. This necessity imposes some further objectives or requirements on the solution method (modeling) and tool (computer code). These may be listed as follows: (1) a good approximation to the real antenna geometry; and (2) feasible computer storage and time requirements. According to these requirements, the work is concentrated on the development of efficient modeling schemes for these type of problems and on reducing the central processing unit (CPU) time required from the computer code. A Method of Moments (MoM) code is developed for the analysis of LTSA's within the parameter ranges given.
A study into the problem of determining electromagnetic solutions at high frequencies for problems involving complex geometries, large sizes and multiple sources (e.g. antennas) has been initiated. Typical applications include the behavior of antennas (and radiators) installed on complex conducting structures (e.g. ships, aircrafts, etc..) with strong interactions between antennas, the radiation patterns, and electromagnetic signals is of great interest for electromagnetic compatibility control. This includes the overall performance evaluation and control of all on-board radiating systems, electromagnetic interference, and personnel radiation hazards. Electromagnetic computational capability exists at NASA LaRC, and many of the codes developed are based on the Moment Method (MM). However, the MM is computationally intensive, and this places a limit on the size of objects and structures that can be modeled. Here, two approaches are proposed: (i) a current-based hybrid scheme that combines the MM with Physical optics, and (ii) an Alternating Direction Implicit-Finite Difference Time Domain (ADI-FDTD) method. The essence of a hybrid technique is to split the overall scattering surface(s) into two regions: (a) a MM zone (MMZ) which can be used over any part of the given geometry, but is most essential over irregular and "non-smooth" geometries, and (b) a PO sub-region (POSR). Currents induced on the scattering and reflecting surfaces can then be computed in two ways depending on whether the region belonged to the MMZ or was part of the POSR. For the MMZ, the current calculations proceed in terms of basis functions with undetermined coefficients (as in the usual MM method), and the answer obtained by solving a system of linear equations. Over the POSR, conduction is obtained as a superposition of two contributions: (i) currents due to the incident magnetic field, and (ii) currents produced by the mutual induction from conduction within the MMZ. This effectively leads to a reduction in the size of linear equations from N to N - Npo with N being the total number of segments for the entire surface and Npo the number of segments over the POSR. The scheme would be appropriate for relatively large, flat surfaces, and at high frequencies. The ADI-FDTD scheme provides for both transient and steady state analyses. The restrictive Courant-Friedrich-Levy (CFL) condition on the time-step is removed, and so large time steps can be chosen even though the spatial grids are small. This report includes the problem definition, a detailed discussion of both the numerical techniques, and numerical implementations for simple surface geometries. Numerical solutions have been derived for a few simple situations.
Model of reentry plasma layer consisting of magnetic line source in ground plane, determining plasma temperature effect, computing radiation pattern of far-zone field
A combiner was designed and fabricated for injecting X- and S-band into a horn for use at various DSN sites. Results indicate that the S-band combiner is much too narrow for use in both receiving and transmitting and that the horn patterns, when scattered, yield an improved efficiency over the present horn-hyperbola system. Predicted performance at DSS 13 by the calculated scattering of the model radiation patterns from the DSS 13 hyperbola is also discussed.
The angles of propagation for the wave front making up a duct mode are presented with the Mach number in the duct. Approximate equations are derived to provide simple utilitarian expressions. These expressions are valid only near the outer wall which is the most important region since the bulk of the acoustic intensity is located there. Exact solutions using Hankel functions are given in an appendix. These data corroborate the approximate solution accuracy near the outer wall. The axial propagation angle is used to infer information about the far-field radiation pattern. The resultant axial angle of propagation in the duct is shown to agree exactly with the peak of the principal lobe to far-field radiation obtained from formal radiation calculations when the Mach number is uniform everywhere. The obtained solution is extended to cover the case of different Mach numbers inside and outside the duct for which exact calculations have not been available for engine inlet configurations.
A symmetric reflectarray, consisting of variable-size square patch elements with a commonly used mathematical model for the horn in the form of a cosine function, has been designed using the transmit mode technique for different f/D ratios with 10 dB edge taper. Subsequently, the antennas were analyzed for the radiation pattern and gain. The infinite array model was used to determine the reflection phase of each patch element in the design and analysis codes. By displacing the feed laterally, the scan characteristics were obtained, such as the beam deviation factor, gain loss, and pattern degradation. The properties of reflect arrays were compared to those of the conventional paraboloidal reflectors. The same procedure was used to study the scan properties of offset reflectarrays. There is no cross-polarized radiation in the principal planes for a symmetric system. Cross-polarized radiation exists in non-principal planes off broadside in symmetric systems, with greater levels for larger values of subtended angles. Such cross-polarized radiation level increases with subtended angle just as cross-polarization level increases with decreasing values of f/D ratios for symmetric paraboloids in non-principal planes. Pattern distortions and gain loss were found to be more severe in the case of a microstrip reflectarray compared to the conventional parabolic reflector. The scan performance of the reflect arrays was found to improve with f/D ratios as is true for paraboloids. In general, scanning by means of displaced feed is limited to a few beam - widths in reflectarrays. Feed displacement in the axial direction of a symmetric reflectarray was investigated and compared to that of paraboloids. The gain loss due to the defocused feed of a reflectarray was found to be nearly the same as that of a paraboloid of the same subtended angle for larger values of f/D, and for displacements away from the antenna. The gain loss of an axially defocused reflectarray was found to be greater than that of a paraboloid for displacements closer to the antenna, especially for smaller values of f/D. In general, the performance of a defocused reflectarray was found to be poorer than that of a comparable paraboloid reflector.
Radiation patterns and gains measured for short backfire antenna as function of antenna dimensions
Variation of radiation pattern of array of two traveling-wave V-antennas and use as spacecraft antenna
Empirical methods have been developed to estimate the test section noise levels and the outside noise radiation patterns of blowdown wind tunnels. Included are considerations of noise generation by control valves, burners, turbulent boundary layers, and exhaust jets as appropriate. Sample test section and radiation field noise estimates are presented. The external estimates are noted to be in good agreement with the limited amount of available measurements.
A volumetric pattern analysis of fuselage-mounted airborne antennas at high frequencies was investigated. The primary goal of the investigation was to develop a numerical solution for predicting radiation patterns of airborne antennas in an accurate and efficient manner. An analytical study of airborne antenna pattern problems is presented in which the antenna is mounted on the fuselage near the top or bottom. Since this is a study of general-type commercial aircraft, the aircraft was modeled in its most basic form. The fuselage was assumed to be an infinitely long perfectly conducting elliptic cylinder in its cross-section and a composite elliptic cylinder in its elevation profile. The wing, cockpit, stabilizers (horizontal and vertical) and landing gear are modeled by "N" sided bent or flat plates which can be arbitrarily attached to the fuselage. The volumetric solution developed utilizes two elliptic cylinders, namely, the roll plane and elevation plane models to approximate the principal surface profile (longitudinal and transverse) at the antenna location. With the belt concept and the aid of appropriate coordinate system transformations the solution can be used to predict the volumetric patterns of airborne antennas in an accurate and efficient manner. Applications of this solution to various airborne antenna problems show good agreement with scale model measurements. Extensive data are presented for a microwave landing antenna system.
The combining of remote sensing technologies to urban-regional energy climatology is studied. It was found to be three dimensional with a mosaic urban surface, each smaller surface with its own radiant and thermal properties. Urban patterns of radiant exchange were found to be constantly changing during diurnal and annual cycles. Results were derived from Barbados data using remote methods for monitoring and mapping radiation. Isoline maps of terrestrial radiation patterns were made generalizing the minute patterns of the scan image.