Search NASA⌕ Search

SEARCH · Search NASA

Results for “raster data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Chronology, eruption duration, and atmospheric contribution of Apollinaris Patera, Mars

Geologic mapping from Viking image data of the Martian volcano Apollinaris Patera allowed identification of 6 major events that shaped its current morphology. Derivation of new topographic data allowed accurate estimates of the volume of erupted products from which estimates of an eruption duration are presented for the edifice and its corresponding atmospheric water contribution. Topographic data were acquired using stereophotogrammetric (Viking picnos 603A42, 639A92) techniques in both profiling and contouring modes (1 km contour). The profiling mode results in a more precise measurement than the contouring mode, but is limited in its areal coverage. The contour data are used in a more general sense to provide synoptic coverage for the volcano. These new stereophotogrammetric measurements constrain the topography to an accuracy of approximately 800 m vertically and approximately 1000 m horizontally. Conversion of the derived contour map to a raster based digital elevation model (DEM) was done by a growing contours interpolation. An ambiguity arises in this volume calculation due to an uncertainty regarding the actual base of the volcano relative to the pre-existing topography. Thus, the volume estimate was bracketed by using the 100 m and the 750 m elevations, which generally correspond to the lower and upper portions of the circumferential basal scarp, respectively. The resulting volumes are 103,000 cu km and 97,000 cu km; therefore the total volume of Apollinaris Patera is estimated to be approximately 100,000 cu km.

Robinson, M. S.↗
NASA NTRS2012

Coordinated STEM/FIB/NanoSIMS Analyses of Presolar Silicates in Comet Dust and Primitive Meteorites

Silicate grains were among the most abundant mineralogical building blocks of our Solar System. These grains were the detritus from earlier generations of stars that have been recycled in the early solar nebula. Rare sub-micrometer survivors of this processing have been identified in meteorites, micrometeorites and interplanetary dust particles (IDPs). These silicate grains are recognized as presolar in origin because of their extremely anomalous isotopic compositions that reflect nucleosynthetic processes in their stellar sources (evolved stars, novae and supernovae). We perform coordinated chemical, mineralogical and isotopic studies of these grains to determine their origins and histories. We examine the complex mineralogy and petrography of presolar silicates using imaging, diffraction and chemical data obtained from thin sections with the JSC JEOL 2500 field-emission STEM equipped with a Noran thin window energy dispersive x-ray (EDX) spectrometer and a Gatan Tridiem GIF. Quantitative element x-ray maps (spectrum images) are acquired by rastering a 4 nm incident probe whose dwell time is minimized to avoid beam damage and element diffusion during mapping. Successive image layers are acquired and combined in order to achieve approx 1% counting statistics for major elements. The IDP samples are prepared by ultramicrotomy of particles embedded in epoxy or elemental sulfur. After EDX mapping, the sections are subjected to C, N, and O isotopic imaging with the JSC NanoSIMS 50L ion microprobe. We prepare sections of some meteorite grains using the JSC FEI Quanta 3D focused ion beam (FIB) instrument. The specimen surface is protected from the FIB milling process by layers of electron beam-deposited C and Pt followed by an ion-deposited Pt layer. We also use the FIB to preferentially remove surrounding grains to reduce the background in subsequent NanoSIMS measurements. For mineralogical studies, we again employ the FIB instrument to deposit a protective cap over the grain of interest and then extract the grain and thin it to electron transparency for TEM analysis.

Keller, Lindsay↗
NASA NTRS1977

Infrared imaging of Jupiter in the 8-14-micrometer spectral region

High-spatial-resolution images of Jupiter were produced on the Hale 200-in. telescope. A programmable wobbling secondary was used to raster-scan the planet with 64 by 64 1-arcsec pixels. Images were made with broadband (8-14 microns) and several 1- and 2-micron-wide filters. All images reveal a belt-and-ozone structure similar to visible photographs. Belts in the broadband data appear to be about 2 K hotter than zones, but contrast varies markedly in different parts of the 8-14-micron spectral region. The lowest belt-zone contrast is found in the hydrogen-opacity-dominated region at 12.5 microns, while images at 9.5 microns exhibit the greatest contrast. Isolated areas are observed to be as much as 4 K hotter than surrounding areas at 9.5 microns. This large contrast is probably due to variations in the distribution of the ammonia clouds in the upper atmosphere.

Terrile, R. J.↗
DOE OSTI2024

Efficient boundary-guided scanning for high-resolution X-ray ptychography

In the realm of X-ray ptychography experiments, a considerable amount of ptychography scans are typically performed within a field of view encompassing the target sample. While it is crucial to obtain overlapping scans in small increments over the region of interest for achieving high-resolution sample reconstruction, a significant number of these scans often redundantly measure the empty background within the wide field of view. To address this inefficiency, an innovative algorithm is proposed that introduces automatic guidance for data acquisition. The algorithm first directs the scan point to actively search for the object of interest within the field of view. Subsequently, it intelligently scans along the perimeter of the sample, strategically acquiring measurements exclusively within the boundary of the region of interest. By employing this approach, a reduction in the number of measurements required to obtain high-resolution reconstruction images is demonstrated, as compared with conventional raster scanning methods. Furthermore, the automatic guidance provided by the algorithm offers the added advantage of saving valuable time during the reconstruction process. Through practical implementation on real experiments, these findings showcase the efficacy of the proposed algorithm in enhancing the efficiency and accuracy of X-ray ptychography experiments. This novel approach holds immense potential for advancing sample analysis and imaging techniques in various scientific disciplines.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2026

Comparison of structurally diverse simulation models for prediction of epidemic outcomes caused by a long-distance dispersed pathogen

Long-distance dispersal (LDD) pathogens pose substantial challenges for epidemic control due to their ability to generate new infection foci at great distances. While various modeling approaches have been developed to understand and manage such outbreaks, little work has compared how models of different structures behave under shared conditions. Here, in this study, we compare four structurally distinct epidemiological models — EPIMUL, GEMF, PoPS, and Warwick — each adapted to simulate the spread of wheat stripe rust (WSR), a wind-dispersed LDD pathogen, under identical epidemiological parameters and dispersal kernel. Using data from a controlled field experiment, we evaluate the ability of each model to replicate disease prevalence under nine intervention scenarios that vary in timing and culling area. While the models differ substantially in design — ranging from spatial grid-based to network-based and raster-based frameworks — the shared dispersal kernel allowed for close alignment in their predictions. All models accurately captured general epidemic trends, particularly the strong effect of early intervention on disease suppression. We qualitatively compared their behavioral responses across scenarios and also evaluated an ensemble prediction by averaging across model outputs. Our findings highlight how integrating shared epidemiological components into distinct modeling frameworks can improve consistency and accuracy, while reinforcing the importance of early culling in managing LDD pathogen outbreaks.

Dispersal kernel↗
NASA NTRS1981

Characterization of point focusing test bed concentrators at JPL

The characterization data were measured using both a flux mapper and a cold water calorimeter. The flux mapper uses a Kendall Radiometer as the sensing device. It is mounted on an x, y, z motor-driven positioning mechanism that allows the sensor to take an x-y flux raster at several Z planes in the vicinity of the concentrators nominal focal plane. Various concepts were tried to protect the concentrator structure from being damaged by the Sun's energy during sun acquisition and deacquisition. A description of both the passive and active protective systems is presented.

Starkey, D. J.↗
NASA NTRS1986

Polar-cap and coronal-hole-associated brightenings of the Sun at millimeter wavelengths

Mapping observations of the Sun at millimeter wavelengths were made on 16 to 22 July 1984 with the 45-m telescope of the Nobeyama Radio Observatory. Seven 36-GHz (8.3-mm) maps and five 98-GHz (3.1-mm) maps were taken with half-power beam widths of 46 arc sec and 17 arc sec, respectively. Instead of the conventional rastering technique, a radial-scan method was adopted in which every scan passes through the disk center. Accordingly, the variation of the atmosphere attenuation due to changes in the weather conditions can be easily estimated and removed by using the brightness values at the disk center as calibration data. Also, the pointing errors of the telescope due to the high-speed scans can be corrected by using the solar limbs as position references. The rms residual errors in relative brightness and position after the corrections were estimated to be approx. 2% and approx. 5 arc sec respectively. To further reduce these errors, enabled us to make high-quality maps with with or approx. 1% uncertainty in brightness. Here and in the following, brightness is expressed in terms of the average brightness of the solar disk as a unit. Note that the brightness temperature of the quiet Sun is approx. 8000 K and approx. 6000 K at 36 GHz and 98 GHz, respectively.

Kosugi, T.↗
DOE OSTI2024

Using Convex Optimization to Efficiently Apportion Tracer and Pollutant Sources From Point Concentration Observations

Abstract Rivers transport elements, minerals, chemicals, and pollutants produced in their upstream basins. A sample from a river is a mixture of all of its upstream sources, making it challenging to pinpoint the contribution from each individual source. Here, we show how a nested sample design and convex optimization can be used to efficiently unmix downstream samples of a well‐mixed, conservative tracer in a steady state system into the contributions of their upstream sources. Our approach is significantly faster than previous methods. We represent the river's sub‐catchments, defined by sampling sites, using a directed acyclic graph. This graph is used to build a convex optimization problem which, thanks to its convexity, can be quickly solved to global optimality—in under a second on desktop hardware for data sets of ∼100 samples or fewer. Uncertainties in the upstream predictions can be generated using Monte Carlo resampling. We provide an open‐source implementation of this approach in Python. The inputs required are straightforward: a table containing sample locations and observed tracer concentrations, along with a D8 flow‐direction raster map. As a case study, we use this method to map the elemental geochemistry of sediment sources for rivers draining the Cairngorms mountains, UK. This method could be extended to non‐conservative and non‐steady state tracers. We also show, theoretically, how multiple tracers could be simultaneously inverted to recover upstream run‐off or erosion rates as well as source concentrations. Overall, this approach can provide valuable insights to researchers in various fields, including water quality, geochemical exploration, geochemistry, hydrology, and wastewater epidemiology.

Barnes, Richard↗
NASA NTRS1986

Photocurrent Imaging Detects Solar-Module Defects

Raster-scanned laser beam excites photocurrents in thin-film amorphous silicon devices. Solar-cell laser scanner uses two galvanometer-driven mirrors to scan laser-beam spot over surface of module or cell under test. Position signals from scan controllers used to index storage of photocurrent signal data in scan-converter image memory. Stored image displayed on television monitor.

Kim, Q.↗
NASA NTRS1984

Soft X-ray polychromator for the Solar Maximum Mission

The XRP was designed to measure the following temporal and spatial properties of the active and flaring Sun: electron temperature, departures from steady state, ion kinetic temperatures, and electron density. The Bent Crystal Spectrometer (BCS) is capable of measuring the broadening and blue shifts often observed in the impulsive phase of flares. The six simultaneous line fluxes indicative of six different temperatures of formation observable by the Flat Crystal Spectrometer (FCS) allows the derivation of the differential emission measure of the plasma at each raster point. During the operational periods of the XRP hundreds of flares of C-level (GOES classification) were observed and brighter in both the FCS and BCS, including 5 X-flares. Associated theoretical work in atomic physics, stimulated in part by the promise of XRP measurements, has benefitted from the experimental data on solar plasmas which the XRP has provided in abundance.

Haisch, B. M.↗
NASA NTRS1989

Analysis of a crossed Bragg cell acousto-optical spectrometer for SETI

The search for radio signals from extraterrestrial intelligent beings (SETI) requires the use of large instantaneous bandwidth (500 MHz) and high resolution (20 Hz) spectrometers. Digital systems with a high degree of modularity can be used to provide this capability, and this method has been widely discussed. Another technique for meeting the SETI requirement is to use a crossed Bragg cell spectrometer as described by Psaltis and Casasent. This technique makes use of the Folded Spectrum concept, introduced by Thomas. The Folded Spectrum is a 2-D Fourier Transform of a raster scanned 1-D signal. It is directly related to the long 1-D spectrum of the original signal and is ideally suited for optical signal processing. The folded spectrum technique has received little attention to date, primarily because early systems made use of photographic film which are unsuitable for the real time data analysis and voluminous data requirements of SETI. An analysis of the crossed Bragg cell spectrometer is presented as a method to achieve the spectral processing requirements for SETI. Systematic noise contributions unique to the Bragg cell system will be discussed.

NASA Discipline Number 52-60↗
NASA NTRS1995

Effects of low earth orbit on the optical performance of multi-layer enhanced high reflectance mirrors

Two mirror designs developed for space applications were flown along with a standard mid-infrared design on the leading and trailing edges of the Long Duration Exposure Facility (LDEF). Preliminary observations of induced changes in optical performance of ZnS-coated mirrors and impact-related microstructural and microchemical effects are described in the proceedings of the First LDEF Post-Retrieval Symposium. In this paper, effects of the induced environment and meteoroid/debris impacts on mirror performance are described in more detail. Also, an analysis of reflectance spectra using the results of Auger and secondary ion mass spectroscopy (SIMS) profiling measurements are used to identify an optical-degradation mechanism for the ZnS-coated mirrors. Structural damage associated with a high-velocity impact on a (Si/Al2O3)-coated mirror was imaged optically and with scanning electron and atomic force microscopy (SEM and AFM). Scanning Auger and SIMS analysis provided chemical mapping of selected impact sites. The impact data suggest design and fabrication modifications for obtaining improved mechanical performance using a design variation identified in preflight laboratory simulations. Auger surface profile and SIMS imaging data verified the conclusion that secondary impacts are the source of contamination associated with the dendrites grown on the leading-edge ZnS-coated test samples. It was also found that dendrites can be grown in the laboratory by irradiating contaminated sites on a trailing-edge ZnS-coated sample with a rastered electron beam. These results suggest a mechanism for dendrite growth.

Donovan, Terence↗
NASA NTRS1986

Generation of attenuation corrected images from lidar data

The interpretation of data generated by aerosol backscatter lidars is often facilitated by presentation of RHI and PPI images. These pictures are especially useful in studies of atmospheric boundary layer structure where convective elements, stratifications and aerosol laden plumes can be easily delineated. Procedures used at the University of Wisconsin to generate lidar images on a color enhanced raster scan display are described.

Eloranta, E. W.↗
NASA NTRS1989

Distributed earth model/orbiter simulation

Distributed Earth Model/Orbiter Simulation (DEMOS) is a network based application developed for the UNIX environment that visually monitors or simulates the Earth and any number of orbiting vehicles. Its purpose is to provide Mission Control Center (MCC) flight controllers with a visually accurate three dimensional (3D) model of the Earth, Sun, Moon and orbiters, driven by real time or simulated data. The project incorporates a graphical user interface, 3D modelling employing state-of-the art hardware, and simulation of orbital mechanics in a networked/distributed environment. The user interface is based on the X Window System and the X Ray toolbox. The 3D modelling utilizes the Programmer's Hierarchical Interactive Graphics System (PHIGS) standard and Raster Technologies hardware for rendering/display performance. The simulation of orbiting vehicles uses two methods of vector propagation implemented with standard UNIX/C for portability. Each part is a distinct process that can run on separate nodes of a network, exploiting each node's unique hardware capabilities. The client/server communication architecture of the application can be reused for a variety of distributed applications.

Geisler, Erik↗
DOE OSTI2022

Multispectral and Thermal Imager Onboard Aerial Platforms Instrument Handbook

The MicaSense Altum imager is an off-the-shelf, synchronized multispectral and thermal camera, combined with a Global Positioning System (GPS) unit and downwelling light sensor (DLS). The Altum takes images of the land surface within its field of view (FOV) across five visible bands and one longwave infrared thermal band. The sensor records the radiance and converts it to digital numbers. Imagery is radiometrically corrected, taking into account the sensor calibration, lens distortions, vignette effects, sun angle, and atmospheric effects (scattering and absorption). The photogrammetry software Agisoft PhotoScan v 1.4 is used to align and stitch the images into a larger composite image using the technique of structure from motion image capture to construct a dense cloud and 3D model of the surface, which is used to produce a digital elevation model of the terrain surveyed and orthomosaic imagery. Land surface leaf area index, albedo, and surface skin temperature are provided for the user. The user can perform raster calculations on the imagery to produce various other vegetative indices, which are used to indicate plant health and land surface characteristics, including Normalized Difference Vegetation Index (NDVI), Green Normalized Difference Vegetation Index (GNDVI), Normalized Difference Water Index (NDWI), surface temperature, and Enhanced_vegetation_index (EVI). This code is provided with the readme file for each data set. The images have a resolution of 20-60 cm/pixel, which are subsampled to 100 cm/pixel.

47 OTHER INSTRUMENTATION↗
NASA NTRS1987

Experiments in encoding multilevel images as quadtrees

Image storage requirements for several encoding methods are investigated and the use of quadtrees with multigray level or multicolor images are explored. The results of encoding a variety of images having up to 256 gray levels using three schemes (full raster, runlength and quadtree) are presented. Although there is considerable literature on the use of quadtrees to store and manipulate binary images, their application to multilevel images is relatively undeveloped. The potential advantage of quadtree encoding is that an entire area with a uniform gray level may be encoded as a unit. A pointerless quadtree encoding scheme is described. Data are presented on the size of the quadtree required to encode selected images and on the relative storage requirements of the three encoding schemes. A segmentation scheme based on the statistical variation of gray levels within a quadtree quadrant is described. This parametric scheme may be used to control the storage required by an encoded image and to preprocess a scene for feature identification. Several sets of black and white and pseudocolor images obtained by varying the segmentation parameter are shown.

Lansing, Donald L.↗
DOE OSTI2024

Data for Grogan et al. "Bringing Hydrologic Realism to Water Markets"

This data set provides model output and post-processing files required to reproduce the results, tables, and figures in the paper "Bringing Hydrologic Realism to Water Markets" by Grogan et al. (in review). Other input data used in this study includes: Lisk, M., Grogan, D., Zuidema, S., Caccese, R., Peklak, D., Zheng, J., Fisher-Vanden, K., Lammers, R., Olmstead, S., & Fowler, L. (2023). Harmonized Database of Western U.S. Water Rights (HarDWR) (Version v1) [Data set]. MSD-LIVE Data Repository. https://doi.org/10.57931/2205619 Two models were used in this study: (1) The University of New Hampshire Water Balance Model WBM, and (2) a Water Market Model. Market model code and model output post-processing code that make use of these data can be found here Model output files are: 1. WBM output files: scenario[x]_wbm_output.zip Where [x] is one of 1, 2, 2a, 3, and 3a Each zipped directory contains 7 gridded NetCDF files, each reporting the 10-year annual average value of a given variable, in units of average mm/day: File Name: wbm_indUseGross_yc.nc; Description: Water withdrawals by industry (part of the urban sector) File Name: wbm_domUseGross_yc.nc; Description: Water withdrawals by the domestic sector (part of the urban sector) File Name: wbm_irrigationGross_yc.nc; Description: Water withdrawals for agriculture File Name: wbm_irrigationExtra_yc.nc; Description: Water withdrawals from unsustainable groundwater for agriculture File Name: wbm_indUseEvap_yc.nc; Description: Consumptive water use by industry File Name: wbm_domUseEvap_yc.nc; Description: Consumptive water use by the domestic sector File Name: wbm_irrigationNet_yc.nc; Description: Consumptive water use by agriculture The file full_cell_area.nc gives the area of each grid cell in km2, which is used for converting water depth to water volume. 2. Water market model output & post processing output Folder: marketTrdSummaries/ Description: Files in this folder are used as input to code 1_WelfareCalculation_actual_trades.R. They summarize historical water right trade transactions in each state. File Name: welfare_gain_by_state_sector.csv; Description: Welfare gains by state and sector, as shown in Figure 3F. Used in code Figure3.R and produced (as a .xlsx file) by code 2_DemandCurves_simulated_trades.R File Name: welfare_data_actual.rdata; Description: welfare gains by WMA from actual historical trades, as shown in Figure 3A. This data is the output of code 1_WelfareCalculation_actual_trades.R File Name: welfare_summary_simulated.xlsx; Description: Welfare gains by state as simulated by the market model in Scenario 1. Produced by code 2_DemandCurves_simulated_trades.R, and used in code 4_WelfareCalculation.R. File Name: welfare_summary_cutoffs.xlsx; Description: Welfare gains by state as simulated by the market model in Scenario 2. Produced by code 3_DemandCurves_simulated_trades_cutoffs.R, and used in code 4_WelfareCalculation.R. File Name: welfare_summary_cutoffs_SGMS.xlsx; Description: Welfare gains by state as simulated by the market model in Scenario 2a. Produced by code 3_DemandCurves_simulated_trades_cutoffs.R, and used in code 4_WelfareCalculation.R. File Name: welfare_data_actual.rdata; Description: Spatial data, actual historical welfare gains by WMA as shown in Figure 3A. Produced by code 4_WelfareCalculation.R and used by code Figure3.R. File Name: welfare_data_simulated.rdata; Description: Spatial data, simulated Scenario 1 welfare gains by WMA as shown in Figure 3B. Produced by code 4_WelfareCalculation.R and used by code Figure3.R. File Name: welfare_data_simulated_cutoffs.rdata; Description: Spatial data, simulated Scenario 2 welfare gains by WMA. Produced by code 4_WelfareCalculation.R and used by code Figure3.R. File Name: welfare_data_simulated_cutoffs_SGMA.rdata; Description: Spatial data, simulated Scenario 2a welfare gains by WMA. Produced by code 4_WelfareCalculation.R and used by code Figure3.R. Additional files are provided for efficient reproduction of tables and figures. These include: File Name: wma_thresold_dates_Scenario2(a).csv; Description: Wet vs. paper right threshold dates for each WMA. Shown in Figure 2A,B. Produced and used by code calculate_thresolds_Figure2.R File Name: WWRTradeBounds (directory); Description: Trade boundary shapefile required to reproduce Figure 3A-D. Used in code Figure3.R File Name: welfare_region_totals.csv; Description: Welfare gains for the entire study region, as shown in Figure 3E. Used in code Figure3.R File Name: Welfare_gain_by_state_sector.csv; Description: Welfare gains by state and sector, as shown in Figure 3F. Used in code Figure3.R and produced (as a .xlsx file) by code 2_DemandCurves_simulated_trades.R File Name: WECC_MERIT_5min_v3b_mask.nc; Description: Gridded file that identified which land grid cells are in the WBM model domain, used for processing in code Figure4.py File Name: Table_1.csv; Description: All data in Table 1, reproducible from WBM output files using code table_1.R

Economics↗
DOE OSTI2020

Using Robotic Manipulators for Radioactive Waste Inspection - 20090

The global nuclear industry has a growing volume of nuclear waste which needs to be scanned, sorted according to its activity and material type, then processed into the correct waste packages for long term storage and disposal. It is vital that there is a detailed understanding of the waste inventory stored in long term waste containers, as knowledge of their contents could predict or prevent any adverse effects in storage. The numerous 'scan and sort' tables which are currently used at many different facilities around the world to sort waste into their correct containers are human operated and require very slow gamma scanning procedures combined with educated guesswork to manually sort the waste. This often leads to excessive conservatisms, with placement of lower activity wastes in higher activity containers, which in turn costs significantly more to store. In the United Kingdom it costs UK Pounds 46 k per cubic meter to store intermediate level waste compared to just UK Pound 2.9 k per cubic meter to store low level waste according to a 2008 Department of Energy and Climate Change report in the UK. A proposed solution to this problem, is the use of a robotic manipulator to automatically inspect the 'scan and sort table' in order to produce an accurate 3D model of the table's waste contents and attach an overlaid radiation map. The radiation map contains spectrometry data and can in consequence be used to distinguish and locate specific radioisotopes. The 3D model should be as accurate as possible in order to allow for a second robot arm with an attached gripper to grasp the objects and place them into their designated long-term storage container. Various scanning procedures are explored in this study including basic raster scanning, adaptive raster scanning and point sampling. The optimal solution will in practice be defined by the required application and activity level of the wastes being inspected. The results presented in this study indicate that it is possible to produce a centimeter accurate 3D model of a mixed assortment of components on a nuclear waste 'scan and sort' table. In addition, it was shown that the waste objects emitting radiation could be accurately identified and located, with an overlaid radiation map. This study is applicable across the nuclear waste management sector. Many of the ideas and concepts developed in this study are applicable in other decommissioning settings for example, dismantling of legacy gloveboxes or routine inspection of nuclear waste packages in storage. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗