Search NASA⌕ Search

SEARCH · Search NASA

Results for “residual strain”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

The Effect of Stochastically Varying Creep Parameters on Residual Stresses in Ceramic Matrix Composites

Constituent properties, along with volume fraction, have a first order effect on the microscale fields within a composite material and influence the macroscopic response. Therefore, there is a need to assess the significance of stochastic variation in the constituent properties of composites at the higher scales. The effect of variability in the parameters controlling the time-dependent behavior, in a unidirectional SCS-6 SiC fiber-reinforced RBSN matrix composite lamina, on the residual stresses induced during processing is investigated numerically. The generalized method of cells micromechanics theory is utilized to model the ceramic matrix composite lamina using a repeating unit cell. The primary creep phases of the constituents are approximated using a Norton-Bailey, steady state, power law creep model. The effect of residual stresses on the proportional limit stress and strain to failure of the composite is demonstrated. Monte Carlo simulations were conducted using a normal distribution for the power law parameters and the resulting residual stress distributions were predicted.

processing↗
NASA NTRS1980

Calculation of residual principal stresses in CVD boron on carbon filaments

A three-dimensional finite element model of the chemical vapor deposition (CVD) of boron on a carbon substrate (B/C) is developed. The model includes an expansion of the boron after deposition due to atomic rearrangement and includes creep of the boron and carbon. Curves are presented to show how the principal residual stresses and the filament elongation vary as the parameters defining deposition strain and creep are varied. The calculated results are compared with experimental axial residual stress and elongation measurements made on B/C filaments. This comparison requires that for good agreement between calculated and experimental results, the deposited boron must continue to expand after deposition, and that the build-up of residual stresses is limited by significant boron and carbon creep rates.

Behrendt, D. R.↗
NASA NTRS1973

Theoretical and experimental investigation of the nonlinear behavior of angleplied boron/aluminum composites

Specimens from angleplied laminates of boron/aluminum composites were tested and the results analyzed. The specimens consisted of eight-ply symmetric layups and were loaded in tension at various angles to the 0 deg-ply direction. Stress-strain curves to specimen fracture were obtained. The analysis was performed using linear composite mechanics which includes residual stresses and a combined stress yield function. The results obtained indicate that angleplied boron/aluminum laminates exhibit a nonlinear stress-strain behavior to fracture. The residual stresses affect the initial and yield laminate properties. Linear composite mechanics is inadequate to predict the mechanical behavior of boron/aluminum angleplied laminates.

Chamis, C. C.↗
NASA NTRS1973

Theoretical and experimental investigation of the nonlinear behavior of angleplied boron/aluminum composites.

Specimens from angleplied laminates of boron/aluminum composites were tested and the results analyzed. The specimens consisted of eight-ply symmetric layups and were loaded in tension at various angles to the 0-deg-ply direction. Stress-strain curves to specimen fracture were obtained. The analysis was performed using linear composite mechanics which includes residual stresses and a combined stress yield function. The results obtained indicate that angleplied boron/aluminum laminates exhibit a nonlinear stress-strain behavior to fracture. The residual stresses affect the initial and 'yield' laminate properties.

Chamis, C. C.↗
NASA NTRS1992

Residual thermal and moisture influences on the analysis of local delaminations

An analysis using laminated plate theory is developed to calculate the strain energy release rate associated with local delaminations originating at off-axis, angle-ply, matrix cracks in laminates subjected to uniaxial loads. The analysis includes the contribution of residual thermal and moisture stresses to the strain energy released. Examples are calculated for the strain energy release rate associated with local delaminations originating at 90 deg and angle-ply(non 90 deg) matrix-ply cracks in glass-epoxy and graphite-epoxy laminates. The solution developed may be used to assess the relative contribution of mechanical, residual thermal, and moisture stresses on the strain energy release rate for local delamination for a variety of lay-ups and materials.

O'Brien, T. K.↗
NASA NTRS1986

Opening and closing of cracks at high cyclic strains

The closure behavior of cracks of different length and at different cyclic strain levels (ranging from predominantly elastic to grossly plastic strains) was studied to observe the effect of residual crack-tip plasticity on crack closure. Cracks were initiated either naturally or artificially (from electric discharge machining pits) in uniaxial test specimens of strengthened alloy steel AISI 4340 with a grain size of 0.016 mm. It was found that, at high strains, cracks closed only when the lowest stress level in the cycle was approached. The stress or the strain opening level depended upon the exact point along the crack length where the observations were made. As the plastic deformation increased, the relative crack opening level was found to decrease and approach the value of stress ratio R. The experimental results were compared with those of three analytical models of crack closure and opening, demonstrating the limitations of the currently available elastic-plastic crack growth analysis.

Iyyer, N. S.↗
NASA NTRS1981

Tidal dissipation in the moon

Euler's equations of motion, modified to include elasticity and solid friction, were used to study the rotation of the moon. Two heuristic models for the anelasticity were considered: Q independent of frequency and Q inversely proportional to the frequency and Q inversely proportional to the frequency of the strain oscillation. Parameters in each model were estimated by weighted least squares from 9 years of lunar laser range observations. The root mean square of the postfit range residuals was 19 cm in each case. For a strain period of 1 month, the estimates of Q obtained with the two models were similar and surprisingly low: 23 + or - 6. The range of uncertaintly, + or - 6, represents our estimate of the true standard deviation of the estimate of Q, as affected by systematic errors; it is 3 times larger than the formal, statistical, standard error.

Cappallo, R. J.↗
DOE OSTI2022

Revisiting Multi-Material Composite Structures with Homogenized Composite Properties

Composite structures inherently develop residual stresses during their curing process. Driven predominately by mismatched thermal strains between differing materials or ply orientations, but also affected by curing process phenomena like polymer shrinkage, these residual stresses can lead to failure within composite structures. There are several methods varying in complexity that can be used to model the development of residual stresses, all of which are capable of capturing sufficient detail to understand the residual stress state at the ply level. However, explicitly modeling all plies of a layup in a composite structure can be prohibitively expensive based on the number of plies, structure size, and required element size. The computational cost can be reduced through the homogenization of the composite layup without losing much fidelity of the overall response of the structure. The homogenization process reduces the many plies of a laminate to a single lamina that reduces complexity and increases the mesh size where a single element can span multiple plies. This report focuses on verification and validation efforts for a homogenization process using a suite of finite element simulations rather than an analytic solution derived from classical laminate theory. Initial verification using representative element volumes indicated there was minimal error in the homogenization process; however, this compounded to a small, but acceptable error in strip and split ring experimental composite structures. The error does under predict the residual stress state in the strip and split ring and should be accounted for when simulating composite structures with homogenized properties.

36 MATERIALS SCIENCE↗
NASA NTRS1978

The effect of impact damage and circular holes on the compressive strength of a graphite-epoxy laminate

Specimens were impacted by 1.27-cm-diameter aluminum spheres with speeds ranging from 52 to 101 m/s. Some specimens were impacted without any applied compressive load and then loaded to failure to determine their residual strength. Other specimens were loaded to a prescribed axial compressive strain and impacted while at that applied load. Loaded specimens that did not fail catastrophically on impact were subsequently loaded to failure to determine their residual strength. Low-velocity impact damage was found to degrade seriously the laminate static compressive strength. Low-strain compression-compression cyclic loading was found to degrade further the compressive strength of impact-damaged specimens. Specimens with circular holes having diameters up to a third of the specimen width were loaded to failure in compression. It was found that circular holes can also degrade the static compressive strength of the laminate. The effects of circular holes and impact damage on the compressive strength of the laminate are compared.

Starnes, J. H., Jr.↗
NASA NTRS1985

Measurement and analysis of critical crack tip processes during fatigue crack growth

The mechanics of fatigue crack growth under constant-amplitudes and variable-amplitude loading were examined. Critical loading histories involving relatively simple overload and overload/underload cycles were studied to provide a basic understanding of the underlying physical processes controlling crack growth. The material used for this study was 7091-T7E69, a powder metallurgy aluminum alloy. Local crack-tip parameters were measured at various times before, during, and after the overloads, these include crack-tip opening loads and displacements, and crack-tip strain fields. The latter were useed, in combination with the materials cyclic and monotonic stress-strain properties, to compute crack-tip residual stresses. The experimental results are also compared with analytical predictions obtained using the FAST-2 computer code. The sensitivity of the analytical model to constant-amplitude fatigue crack growth rate properties and to through-thickness constrain are studied.

Davidson, D. L.↗
NASA NTRS2013

Low Temperature Creep of Hot-Extruded Near-Stoichiometric NiTi Shape Memory Alloy: Effect of Thermal Cycling - Part 2

This paper is the first report on the effect prior low temperature creep on the thermal cycling behavior of NiTi. The isothermal low temperature creep behavior of near-stoichiometric NiTi between 300 and 473 K was discussed in Part I. The effect of temperature cycling on its creep behavior is reported in the present paper (Part II). Temperature cycling tests were conducted between either 300 or 373 K and 473 K under a constant applied stress of either 250 or 350 MPa with hold times lasting at each temperature varying between 300 and 700 h. Each specimen was pre-crept either at 300 or at 473 K for several months under an identical applied stress as that used in the subsequent thermal cycling tests. Irrespective of the initial pre-crept microstructures, the specimens exhibited a considerable increase in strain with each thermal cycle so that the total strain continued to build-up to 15 to 20 percent after only 5 cycles. Creep strains were immeasurably small during the hold periods. It is demonstrated that the strains in the austenite and martensite are linearly correlated. Interestingly, the differential irrecoverable strain, in the material measured in either phase decreases with increasing number of cycles, similar to the well-known Manson-Coffin relation in low cycle fatigue. Both phases are shown to undergo strain hardening due to the development of residual stresses. Plots of true creep rate against absolute temperature showed distinct peaks and valleys during the cool-down and heat-up portions of the thermal cycles, respectively. Transformation temperatures determined from the creep data revealed that the austenitic start and finish temperatures were more sensitive to the pre-crept martensitic phase than to the pre-crept austenitic phase. The results are discussed in terms of a phenomenological model, where it is suggested that thermal cycling between the austenitic and martensitic phase temperatures or vice versa results in the deformation of the austenite and a corresponding development of a back stress due to a significant increase in the dislocation density during thermal cycling.

Raj, S. V.↗
DOE OSTI2022

Deformation twinning and detwinning in extruded Mg-4Al: In-situ experiment and crystal plasticity simulation

Deformation twinning and detwinning in extruded Mg-4Al were investigated using in-situ SEM-DIC experiments and crystal plasticity finite element (CPFE) simulation. In this study, the in-situ SEM-DIC method was used to provide a unique set of data including twin/detwin characteristics and twin area fraction in addition to strain maps. A statistical analysis of the activation of twin variants and twin area fraction during both twinning and detwinning was conducted. A strong correlation was found between twin growth/shrinkage and the Schmid Factor (SF) for individual twin variants Higher twin SF during loading and unloading led to higher twin growth and shrinkage, respectively. However, after the applied compressive strain was removed, the pattern of the twin area fractions of the residual twin variants versus their nominal SFs did not follow the trend observed at the maximum compressive strain. Using a systematic methodology and an advanced twin/detwin model, the PRISMS-Plasticity CPFE simulation was calibrated using experimentally determined stress versus strain and twin area fraction versus strain information. A comprehensive evaluation of the CPFE model was conducted to determine its ability to capture the statistics of twin variants activation and twin area fraction. CPFE accurately captured the statistical aspects of both twinning and detwinning. Finally, it also predicted the first dominant twin variant for 47.5% of the grains and at least one of the two dominant twin variants for 80% of the grains at maximum compressive strain.

36 MATERIALS SCIENCE↗
NASA NTRS1995

Mechanical properties of high-temperature superconducting wires

Bending strength, fracture toughness, and elastic modulus data were acquired for YBa2Cu3O(x), Bi2Sr2CaCu2O(x) (Bi,Pb)2Sr2Ca2Cu3O(x), and Tl2Ba2Ca2Cu3O(x) bars. These data and thermal expansion coefficients strongly suggest that the maximum possible tensile strain without fracture of bulk tapes or wires is approximately equals 0.2%. In Ag-clad conductors, residual stresses will be of limited benefit, but fractures produced by larger strains can be accommodated by shunting current through the Ag.

Goretta, K. C.↗
DOE OSTI2021

Residual stresses and microstructure within Allvac 718Plus laser powder bed fusion bars

The residual stresses within Allvac 718Plus bars built using LBPF with different laser powers, speeds and table displacements were measured using diffraction and mechanical methods and modelled with the baseplate attached and then removed. The residual stress profiles within the bars from the top surface down through the bulk were all quite similar, becoming less tensile due to a strain hardening mechanism. Table displacement has the greatest impact on residual stress, decreasing with increasing displacement/powder layer thickness. There was good agreement amongst the modeling and measurements. The microstructures were examined and varied slightly with energy density with higher densities having larger grains and enhanced post solidification diffusion. We found energy density had minimal impact on the residuals stresses within the parameters to produce dense material.

36 MATERIALS SCIENCE↗
NASA NTRS1971

Effects of loading sequence for notched specimens under high-low two-step fatigue loading

The effects of loading sequence on crack-initiation period were investigated for notched aluminum-alloy specimens under high-low two-step loading with special emphasis on local cyclic stresses and strains at the notch root. Local stress and strain were determined by a procedure based on an equation proposed by Neuber which relates elastoplastic stress and strain at a notch. Local stress and strain were also measured experimentally to verify the Neuber equation. The effects of initial high load on the crack-initiation periods were demonstrated with notched specimens and were simulated in unnotched specimens fatigue tested with local stress sequences. An analysis of the results indicated that sequence effects were not caused solely by local residual stresses, as is usually assumed; the existence of a damaging effect, resulting from the high local strain cycles, was demonstrated. The sequence effects observed with notched specimens were interpreted as the combined result of residual stresses and high local strain cycles.

Crews, J. H., Jr.↗
DOE OSTI2024

Identifying multiple synergistic factors on the susceptibility to stress relaxation cracking in variously heat-treated weldments

The 347H austenitic stainless steel has been widely used for pressure vessels and pipeline (PVP) applications due to its excellent creep and corrosion resistance, which fit ideally to the harsh conditions in petrochemical industries, fossil fuel or nuclear power plants, and modern energy storages. However, a failure mode has been commonly observed with cracks emerging at the heat affected zone (HAZ) of weldments during post-weld heat treatment (PWHT) or under intermediate to high temperature service conditions. This phenomenon is termed as Stress Relaxation Cracking (SRC) since the purpose of PWHT is to relieve the welding-induced residual stress fields, or as Stress Age Cracking (SAC) if failure happens during service. A leading literature explanation of this failure suggests that the residual stress relaxation and the precipitation dissolution and/or re-precipitation occur in the same temperature range, which can lead to locally high strains and thus to crack at the grain boundaries. Since in situ spatial measurements of residual stress fields, microstructural evolution, and failure processes are nearly infeasible, this work recourses to a micromechanical finite element framework that models the high temperature failure as the nucleation and growth of grain boundary cavities, whereas various parameters such as thermomechanical loading history and its evolution, the competition of grain-interior dislocation creep and grain-boundary diffusion in failure lifetime, and microstructural heterogeneities (such as the precipitate free zone near grain boundaries) can be quantitatively incorporated. It can be concluded from these microstructure-explicit simulations that an accurate knowledge of residual stress evolution and a carefully calibrated set of material constitutive parameters are the essential prerequisites for lifetime predictions. The understanding of individual governing factors also leads to a mechanistic interpretation of the observed SRC susceptibility C-curves. In conclusion, these results suggest that the criticality of residual stress evolution, but not the precipitation-induced local strains, be the leading factor for SRC.

347H stainless steel weldments↗
DOE OSTI2024

Data for Pilot-Scale Processing of Miscanthus x giganteus for Recovery of Anthocyanins Integrated with Production of Microbial Lipids and Lignin-Rich Residue

Chemical-free hydrothermal pretreatment of Miscanthus x giganteus (Mxg) at the lab scale using high liquid-to-solid ratios resulted in the recovery of anthocyanins and enhanced enzymatic digestibility of residual biomass. In this study, the process is scaled up by using a continuous hydrothermal pretreatment reactor operated at a low liquid-to-solid ratio (50 % w/w solids) as an important step towards commercialization. Anthocyanin yield was 70 % w/w at the pilot scale (50 kg of Mxg), compared to the 94 % w/w yield achieved at the lab scale (0.5 g of Mxg). The pretreated biomass was subsequently refined mechanically using a disc mill to increase the accessibility of cellulose by cellulases. Enzymatic saccharification of the pretreated and disc-milled residue yielded 238 g/L sugar concentration by operating in fed-batch mode at 50 % w/v solids content. Two strains of Rhodosporidium toruloides were evaluated for converting the hydrolysate sugars into microbial lipids, and strain Y-6987 had the highest lipid titer (11.0 g/L). Further, the residue left after enzymatic saccharification was determined to be enriched 1.7-fold in the lignin content. This lignin-rich residue has value as a feedstock for the production of sustainable aviation fuel precursors and other high-value lignin-based chemicals. Hence the proposed biorefinery based on Mxg creates an opportunity for generating revenue from multiple high-value products. As the demand for biofuels and biobased products is rising, the biorefinery products from Mxg would create a niche in the industrial sector.

Conversion↗
NASA NTRS1992

The rhodopsins: structure and function. Introduction

Nature makes use of the propensity of retinal for light-dependent double-bond isomerization in a number of systems and in a variety of ways. The common theme for light receptors based on this kind of chemistry is that (1) the retinal is bound in most cases to a small membrane protein via a protonated lysine-retinal Schiff base, (2) the absorption maximum in the visible is tuned to a suitable wavelength largely by electrostatic interaction with polar protein residues, and (3) the light-induced bond rotations and strains in the retinal set off reaction chains during which at least part of the excess free energy acquired is transferred to the protein and causes pK shifts of acidic residues and/or backbone conformational changes. The physiological consequence of the process initiated by absorption of light is either the activation of an information transfer chain (sensory and visual rhodopsins) or energy transduction which drives the electrogenic movement of ions across the membrane (ion-motive rhodopsins). Rhodopsins with these functions occur in bacteria and in higher organisms; from an evolutionary standpoint they are not related to one another. Nevertheless, all of these proteins are remarkably similar and form a distinct family.

NASA Discipline Number 52-30↗