Results for “rotating flows” — Page 13

NASA NTRS1979

Rotary balance data for a single-engine trainer design for an angle-of-attack range of 8 deg to 90 deg

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in the Langley spin tunnel are presented in plotted form for a 1/6 scale, single engine trainer airplane model. The configurations tested included the basic airplane, various wing leading edge devices, elevator, aileron and rudder control settings as well as airplane components. Data are presented without analysis for an angle of attack range of 8 to 90 degrees and clockwise and counter-clockwise rotations.

Pantason, P.↗

NASA NTRS1983

Analytical and Experimental Study of Flow Through an Axial Turbine Stage with a Nonuniform Inlet Radial Temperature Profile

Results are presented for a typical nonuniform inlet radial temperature profile through an advanced single-stage axial turbine and compared with the results obtained for a uniform profile. Gas temperature rises of 40 K to 95 K are predicted at the hub and tip corners at the trailing edges of the pressure surfaces in both the stator and rotor due to convection of hot fluid from the mean by the secondary flow. The inlet temperature profile is shown to be mixed out at the rotor exit survey plane (2.3 axial chords downstream of the rotor trailing edge) in both the analysis and the experiment. The experimental rotor exit angle profile for the nonuniform inlet temperature profile indicates underturning at the tip caused by increased clearance. Severe underturning also occurs at the mean, both with and without the nonuniform inlet temperature profile. The inviscid rotational flow code used in the analysis fails to predict the underturning at the mean, which may be caused by viscous effects.

Schwab, J. R.↗

NASA NTRS1983

Analytical and experimental study of flow through an axial turbine stage with a nonuniform inlet radial temperature profile

Results are presented for a typical nonuniform inlet radial temperature profile through an advanced single-stage axial turbine and compared with the results obtained for a uniform profile. Gas temperature rises of 40 K to 95 K are predicted at the hub and tip corners at the trailing edges of the pressure surfaces in both the stator and rotor due to convection of hot fluid from the mean by the secondary flow. The inlet temperature profile is shown to be mixed out at the rotor exit survey plane (2.3 axial chords downstream of the rotor trailing edge) in both the analysis and the experiment. The experimental rotor exit angle profile for the nonuniform inlet temperature profile indicates underturning at the tip caused by increased clearance. Severe underturning also occurs at the mean, both with and without the nonuniform inlet temperature profile. The inviscid rotational flow code used in the analysis fails to predict the underturning at the mean, which may be caused by viscous effects. Previously announced in STAR as N83-27958

Schwab, J. R.↗

NASA NTRS1979

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 1: High-wing model B

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in a spin tunnel are presented in plotted form for a 1/6.5 scale, single engine, high wing, general aviation airplane model. The configurations tested included the basic airplane, various wing leading-edge devices, tail designs, and rudder control settings as well as airplane components. Data are presented without analysis for an angle of attack range of 8 deg to 90 deg and clockwise and counter-clockwise rotations covering an omega b/2V range from 0 to 0.85.

Bihrle, W., Jr.↗

NASA NTRS1979

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 deg to 90 deg. 2: Low-wing model B

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in the spin tunnel are presented in plotted form for a 1/6.5 scale, single engine, low wing, general aviation airplane model. The configurations tested included the basic airplane, various wing leading-edge devices, tail designs, and rudder control settings as well as airplane components. Data are presented without analysis for an angle-of-attack range of 8 deg to 90 deg and clockwise and counter-clockwise rotations covering an (omega)(b)/2V range from 0 to 0.85.

Bihrle, W., Jr.↗

NASA NTRS1979

Rotary balance data for a typical single-engine general aviation design for an angle-of-attack range of 8 degrees to 35 degrees, 3. Effect of wing leading-edge modifications, model A

Aerodynamic characteristics obtained in a rotational flow environment utilizing a rotary balance located in the Langley spin tunnel are presented in plotted form for a 1/5 scale, single-engine, low-wing, general aviation airplane model. The configurations tested included the basic airplane, sixteen wing leading-edge modifications and lateral-directional control settings. Data are presented for all configurations without analysis for an angle of attack range of 8 deg to 35 deg and clockwise and counter-clockwise rotations covering an Omega b/2v range from 0 to 0.85. Also, data are presented above 35 deg of attack for some configurations.

Bihrle, W., Jr.↗

NASA NTRS2008

Deconvoluting the Friction Stir Weld Process for Optimizing Welds

In the friction stir welding process, the rotating surfaces of the pin and shoulder contact the weld metal and force a rotational flow within the weld metal. Heat, generated by the metal deformation as well as frictional slippage with the contact surface, softens the metal and makes it easier to deform. As in any thermo-mechanical processing of metal, the flow conditions are critical to the quality of the weld. For example, extrusion of metal from under the shoulder of an excessively hot weld may relax local pressure and result in wormhole defects. The trace of the weld joint in the wake of the weld may vary geometrically depending upon the flow streamlines around the tool with some geometry more vulnerable to loss of strength from joint contamination than others. The material flow path around the tool cannot be seen in real time during the weld. By using analytical "tools" based upon the principles of mathematics and physics, a weld model can be created to compute features that can be observed. By comparing the computed observations with actual data, the weld model can be validated or adjusted to get better agreement. Inputs to the model to predict weld structures and properties include: hot working properties ofthe metal, pin tool geometry, travel rate, rotation and plunge force. Since metals record their prior hot working history, the hot working conditions imparted during FSW can be quantified by interpreting the final microstructure. Variations in texture and grain size result from variations in the strain accommodated at a given strain rate and temperature. Microstructural data from a variety of FSWs has been correlated with prior marker studies to contribute to our understanding of the FSW process. Once this stage is reached, the weld modeling process can save significant development costs by reducing costly trial-and-error approaches to obtaining quality welds.

Schneider, Judy↗

NASA NTRS1989

A critical comparison of turbulence models for homogeneous shear flows in a rotating frame

A variety of turbulence models, including five second-order closure models and four two equation models, are tested for the problem of homogeneous turbulent shear flow in a rotating frame. The model predictions for the time evolution of the turbulent kinetic energy and dissipation rate, as well as those for the equilibrium states, are compared with the results of physical and numerical experiments. Most of the two-equation models predict the same results for all rotation rates (omega/S) in which there is an exponential time growth of the turbulent kinetic energy and dissipation rate. The second-order closures are qualitatively superior since, consistent with physical and numerical experiments, they only predict this type of unstable flow for intermediate rotation rates in the range -0.1 less than or equal to omega/S less than or equal to 1.6. For rotation rates outside this range, there is an exchange of stabilities with a solution whose kinetic energy and dissipation rate decay with time. Although the second-order closures are superior to the two-equation models, there are still problems with the quantitative accuracy of their predictions.

Speziale, Charles G.↗

NASA NTRS1989

A critical comparison of turbulence models for homogeneous shear flows in a rotating frame

A variety of turbulence models, including five second-order closure models and four two equation models, are tested for the problem of homogeneous turbulent shear flow in a rotating frame. The model predictions for the time evolution of the turbulent kinetic energy and dissipation rate, as well as those for the equilibrium states, are compared with the results of physical and numerical experiments. Most of the two-equation models predict the same results for all rotation rates (omega/S) in which there is an exponential time growth of the turbulent kinetic energy and dissipation rate. The second-order closures are qualitatively superior since, consistent with physical and numerical experiments, they only predict this type of unstable flow for intermediate rotation rates in the range -0.1 less than or equal to omega/S less than or equal to 1.6. For rotation rates outside this range, there is an exchange of stabilities with a solution whose kinetic energy and dissipation rate decay with time. Although the second-order closures are superior to the two-equation models, there are still problems with the quantitative accuracy of thier predictions.

Speziale, Charles G.↗

NASA NTRS1990

A critical comparison of turbulence models for homogeneous shear flows in a rotating frame

A variety of turbulence models, including five second-order closure models and four two equation models, are tested for the problem of homogeneous turbulent shear flow in a rotating frame. The model predictions for the time evolution of the turbulent kinetic energy and dissipation rate, as well as those for the equilibrium states, are compared with the results of physical and numerical experiments. Most of the two-equation models predict the same results for all rotation rates (omega/S) in which there is an exponential time growth of the turbulent kinetic energy and dissipation rate. The second-order closures are qualitatively superior since, consistent with physical and numerical experiments, they only predict this type of unstable flow for intermediate rotation rates in the range -0.1 less than or equal to omega/S less than or equal to 1.6. For rotation rates outside this range, there is an exchange of stabilities with a solution whose kinetic energy and dissipation rate decay with time. Although the second-order closures are superior to the two-equation models, there are still problems with the quantitative accuracy of their predictions.

Speziale, Charles G.↗

NASA NTRS1986

Confinement of thermocapillary floating zone flow by uniform rotation

Smith and Greenspan (1984) examined theoretically the idea of using a uniform rotation of the floating zone system to confine the thermocapillary flow in crystal growth experiments to the melt sidewall, leaving the interior of the melt passive. Here, that model is extended to a full zone with a more realistic temperature distribution imposed on the sidewall, and both linear and nonlinear thermocapillary flows are theoretically studied. Linearized, analytical solutions are found using singular perturbation theory and the various sidewall boundary layers described by Greenspan (1969) for rotating fluids. The analytical and linearized numerical results are compared, and the linear and nonlinear flows are discussed. The results demonstrate that the thermocapillary flow is strong and that rotation cannot confine the flow. Temperature advection by strongly nonlinear flow is significant even for the small Prandtl number of silicon.

Fowlis, W. W.↗

NASA NTRS1992

An integrated development of the equations of motion for elastic hypersonic flight vehicles

An integrated, consistent analytical framework is developed for modeling the dynamics of elastic hypersonic flight vehicles. A Lagrangian approach is used in order to capture the dynamics of rigid-body motion, elastic deformation, fluid flow, rotating machinery, wind, and a spherical rotating earth model, and to account for their interactions with each other. A vector form of the force, moment and elastic-deformation equations is developed from Lagrange's equation; a useable scalar form of these equations is also presented. The appropriate kinematic equations are developed, and are presented in a useable form. A preliminary study of the significance of selected terms in the equations of motion is conducted. Using generic data for a single-stage-to-orbit vehicle, it was found that the Coriolis force can reach values of up to 6 percent of the vehicle weight, and that the forces and moments attributable to fluid-flow terms can be significant.

Bilimoria, Karl D.↗

DOE OSTI2024

Swirls and scoops: Ice base melt revealed by multibeam imagery of an Antarctic ice shelf

Knowledge gaps about how the ocean melts Antarctica’s ice shelves, borne from a lack of observations, lead to large uncertainties in sea level predictions. Using high-resolution maps of the underside of Dotson Ice Shelf, West Antarctica, we reveal the imprint that ice shelf basal melting leaves on the ice. Convection and intermittent warm water intrusions form widespread terraced features through slow melting in quiescent areas, while shear-driven turbulence rapidly melts smooth, eroded topographies in outflow areas, as well as enigmatic teardrop-shaped indentations that result from boundary-layer flow rotation. Full-thickness ice fractures, with bases modified by basal melting and convective processes, are observed throughout the area. This new wealth of processes, all active under a single ice shelf, must be considered to accurately predict future Antarctic ice shelf melt.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2023

Monsoon Depression Amplification by Horizontal Shear and Humidity Gradients: A Shallow Water Perspective

Transient, synoptic-scale vortices produce a large fraction of total rainfall in most monsoon regions and are often associated with extreme precipitation. However, the mechanism of their amplification remains a topic of active research. For monsoon depressions, which are the most prominent synoptic-scale vortex in the Asian–Australian monsoon, recent work has suggested that meridional gradients in zonal wind in the vortex environment may produce growth through barotropic instability, while meridional gradients in environmental humidity have also been proposed to cause amplification through coupling with precipitating convection. Here, a two-dimensional shallow water model on a sphere with parameterized precipitation is used to examine the relative role played by these two environmental gradients. By systematically varying the meridional moisture gradient and meridional wind shear for both weak, quasi-linear waves and finite-amplitude isolated vortices, we show that rotational winds in the initial vortex are amplified most strongly by meridional shear of the environmental zonal wind, while vortex precipitation rates are most sensitive to environmental moisture gradients. The growth rate in the presence of both gradients is less than the sum of growth rates in the presence of isolated gradients, as the phase relation between moisture and vorticity anomalies becomes distorted with increasing shear. In conclusion, these results suggest that background meridional gradients in both zonal wind and environmental humidity can contribute to the amplification of vortices to monsoon depression strength, but with some degree of decoupling of the dry rotational flow and the moist convection.

54 ENVIRONMENTAL SCIENCES↗

NASA NTRS1974

Effects of several factors on theoretical predictions of airplane spin characteristics

The influence of different mathematical and aerodynamic models on computed spin motion was investigated along with the importance of some of the aerodynamic and nonaerodynamic quantities defined in these models. An analytical technique was used which included the aerodynamic forces and moments acting on a spinning aircraft due to steady rotational flow and the contribution of the rotary derivatives to the oscillatory component of the total angular rates. It was shown that (1) during experimental-analytical correlation studies, the flight-recorded control time histories must be faithfully duplicated since the spinning motion can be sensitive to a small change in the application of the spin entry controls; (2) an error in the assumed inertias, yawing moments at high angle of attack, and initial spin entry bank angle do not influence the developed spin significantly; (3) damping in pitch derivatives and the center of gravity location play a role in the spinning motion; and (4) the experimental spin investigations conducted in a constant atmospheric density environment duplicate the Froude number only at the initial full-scale spin altitude (since the full-scale airplane at high altitudes experiences large density changes during the spin.)

Bihrle, W., Jr.↗

NASA NTRS1975

Starting vortex, separation bubbles and stall - A numerical study of laminar unsteady flow around an airfoil

The stalling characteristics of an airfoil in a laminar viscous incompressible fluid are investigated. The governing equations in terms of the vorticity and stream function are solved using an implicit finite-difference scheme and point successive relaxation procedure. The development of the impulsively started flow, the initial generation of circulation, and the behavior of the forces at large times are studied. Following the impulsive start, the lift is at first very large and then it rapidly drops. The subsequent growth of circulation and lift is associated with the starting vortex. After incipient separation, the lift increases owing to enlargement of the separation bubble and intensification of the flow rotation in it. The extension of this bubble beyond the trailing edge causes it to rupture and brings about the stalling characteristics of the airfoil. Subsequently, new bubbles are formed near the upper surface of the airfoil and are swept away. The behavior of the lift acting on the airfoil is explained in terms of the strength and sense of these bubbles.

Mehta, U. B.↗

NASA NTRS1980

High-latitude ion convection in the nighttime F region

A large data base of Atmosphere Explorer C measurements of the bulk ion velocity vector in the high-latitude F region has been examined. The concept of shear and rotational flow reversals is expanded upon to determine the extent to which the boundary between antisunward and sunward convection (i.e., a polar cap boundary) is an electrostatic equipotential. A most important factor in characterizing the nature of the large-scale geometrical configuration of the nighttime F region convection is the location and extent of quasi-equipotential regions of the convection reversal boundary.

Heelis, R. A.↗

NASA NTRS1980

Spin prediction techniques

The NASA Langley Research Center has the responsibility to advance the state-of-the-art in the area of stall/spin technology. This includes the development and validation of experimental and analytical techniques for the prediction of stall/spin characteristics. As a part of this effort, a rotary balance facility located in the Langley spin tunnel was developed two and a half years ago to rapidly identify an airplane's aerodynamic characteristics in a rotational flow environment. On-line rotary balance data plots and on-line predicted steady spin modes permit the designer to develop, on site, a configuration highly resistant to spins, or one which has good spin characteristics, i.e., no spin equilibrium conditions possible with lateral-directional controls neutral, if the airplane is to be used for acrobatic maneuvers or training. The rotary balance data are also used to compute time histories of a spin's incipient, developed, and recovery phases. These spin analysis techniques and their correlation with spin tunnel model and full-scale flight results are discussed herein.

Bihrle, W., Jr.↗