SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Tabulated pressure data are presented on the right upper wing surface, right lower wing surface, and SRM booster of the integrated space shuttle vehicle configuration. For Vol. 1, see N76-15246.
The possible effects of the interaction of the plumes from the two solid rocket motors (SRM) from the space shuttles and mixing of the rocket exhaust products and ambient air in the base recirculation region on the total nitrous oxide deposition rate in the stratosphere were investigated. It was shown that these phenomena will not influence the total NOx deposition rate. It was also shown that uncertainties in the particle size of Al2O3, size distributions and particle/gas drag and heat transfer coefficients will not have a significant effect on the predicted NOx deposition rate. The final results show that the total mass flow of NOx leaving the plume at 30 km altitude is 4000 g./sec with a possible error factor of 3. For a vehicle velocity of 1140 meter/sec this yields an NOx deposition rate of about 3.5 g./meter. The corresponding HCl deposition rate at this altitude is about a factor of 500 greater than this value.
Results are presented of research aimed at improving the assessment of off-nominal internal ballistic performance including tailoff and thrust imbalance of two large solid-rocket motors (SRMs) firing in parallel. Previous analyses using the Monte Carlo technique were refined to permit evaluation of the effects of radial and circumferential propellant temperature gradients. Sample evaluations of the effect of the temperature gradients are presented. A separate theoretical investigation of the effect of strain rate on the burning rate of propellant indicates that the thermoelastic coupling may cause substantial variations in burning rate during highly transient operating conditions. The Monte Carlo approach was also modified to permit the effects on performance of variation in the characteristics between lots of propellants and other materials to be evaluated. This permits the variabilities for the total SRM population to be determined. A sample case shows, however, that the effect of these between-lot variations on thrust imbalances within pairs of SRMs is minor in compariosn to the effect of the within-lot variations. The revised Monte Carlo and design analysis computer programs along with instructions including format requirements for preparation of input data and illustrative examples are presented.
An analysis of the unsteady aerodynamics of bodies with concave nose geometries was performed. The results show that the experimentally observed pulsating flow on spiked bodies and in forward facing cavities can be described by the developed simple mathematical model of the phenomenon. Static experimental data is used as a basis for determination of the oscillatory frequency of spike-induced flow pulsations. The agreement between predicted and measured reduced frequencies is generally very good. The spiked-body mathematical model is extended to describe the pulsations observed in forward facing cavities and it is shown that not only the frequency but also the pressure time history can be described with the accuracy needed to predict the experimentally observed time average effects. This implies that it should be possible to determine analytically the impact of the flow pulsation on the structural integrity of the nozzles for the jettisoned empty SRM-shells.
Results of a study of radon migration through columns of fine particulate materials, at total pressures of 0.02-0.2 torr, are reported. Materials studied were: NBS Glass Spheres (SRM 1003), Emerson & Cuming Eccospheres (IG-101), activated coconut charcoal, Lipaci obsidian, and W-1 Standard Diabase. Rates of diffusion were used to derive heats of adsorption for radon on the materials tested. The most reliable values found clustered around 8-9 kcal/mole. These high heats of adsorption, if typical for most materials, combined with low percentages of radon emanation by lunar soils found by other researchers, imply that random walk diffusion will not be an important mechanism for redistributing the radon and the radon daughters produced in the lunar regolith. In particular, since random walk migration is not a sufficient mechanism to account for localized high concentrations of radon-222 and its daughter polonium-210 observed by the Apollo 15 and 16 command modules, an alternative mechanism is proposed, in which radon would be swept to the surface by other gases during intermittent venting events.
The Monte Carlo method of statistical analysis is used to investigate the theoretical thrust imbalance of pairs of solid rocket motors (SRMs) firing in parallel. Sets of the significant variables are selected using a random sampling technique and the imbalance calculated for a large number of motor pairs using a simplified, but comprehensive, model of the internal ballistics. The treatment of burning surface geometry allows for the variations in the ovality and alignment of the motor case and mandrel as well as those arising from differences in the basic size dimensions and propellant properties. The analysis is used to predict the thrust-time characteristics of 130 randomly selected pairs of Titan IIIC SRMs. A statistical comparison of the results with test data for 20 pairs shows the theory underpredicts the standard deviation in maximum thrust imbalance by 20% with variability in burning times matched within 2%. The range in thrust imbalance of Space Shuttle type SRM pairs is also estimated using applicable tolerances and variabilities and a correction factor based on the Titan IIIC analysis.
As part of a continuing study of the environmental effects of solid rocket motor (SRM) operations in the troposphere, a numerical model was used to simulate the afterburning processes occurring in solid rocket motor plumes and to predict the quantities of potentially harmful chemical species which are created. The calculations include the effects of finite-rate chemistry and turbulent mixing. It is found that the amount of NO produced is much less than the amount of HCl present in the plume, that chlorine will appear predominantly in the form of HCl although some molecular chlorine is present, and that combustion is complete as is evident from the predominance of carbon dioxide over carbon monoxide.
Development of a procedure for the reliability analysis of the solid rocket motor case of the space shuttle is described. The analysis is based on probabilistic fracture mechanics and consideration of a probability distribution for the initial flaw sizes. The reliability analysis can be used to select design variables, such as the thickness of the SRM case, projected design life and proof factor, on the basis of minimum expected cost and specified reliability bounds. Effects of fracture control plans such as the non-destructive inspections and the material erosion between missions can also be considered in the developed methodology for selection of design variables. The reliability-based procedure can be easily modified to consider other similar structures and different fracture control plans.
An active optical technique (differential absorption lidar (DIAL)) for detecting, ranging, and quantifying the concentration of anhydrous HCl contained in the ground cloud emitted by solid rocket motors (SRM) is evaluated. Results are presented of an experiment in which absorption coefficients of HCl were measured for several deuterium fluoride (DF) laser transitions demonstrating for the first time that a close overlap exists between the 2-1 P(3) vibrational transition of the DF laser and the 1-0 P(6) absorption line of HCl, with an absorption coefficient of 5.64 (atm-cm) to the -1 power. These measurements show that the DF laser can be an appropriate radiation source for detecting HCl in a DIAL technique. Development of a mathematical computer model to predict the sensitivity of DIAL for detecting anhydrous HCl in the ground cloud is outlined, and results that assume a commercially available DF laser as the radiation source are presented.
The Monte Carlo method was used to investigate thrust imbalance and its first time derivative throughtout the burning time of pairs of solid rocket motors firing in parallel. Results obtained compare favorably with Titan 3 C flight performance data. Statistical correlations of the thrust imbalance at various times with corresponding nominal trace slopes suggest several alternative methods of predicting thrust imbalance. The effect of circular-perforated grain deformation on internal ballistics is discussed, and a modified design analysis computer program which permits such an evaluation is presented. Comparisons with SRM firings indicate that grain deformation may account for a portion of the so-called scale factor on burning rate between large motors and strand burners or small ballistic test motors. Thermoelastic effects on burning rate are also investigated. Burning surface temperature is calculated by coupling the solid phase energy equation containing a strain rate term with a model of gas phase combustion zone using the Zeldovich-Novozhilov technique. Comparisons of solutions with and without the strain rate term indicate a small but possibly significant effect of the thermoelastic coupling.
Results of research aimed at improving the predictability of off nominal internal ballistics performance of solid propellant rocket motors (SRMs) including thrust imbalance between two SRMs firing in parallel are reported. The potential effects of nozzle throat erosion on internal ballistic performance were studied and a propellant burning rate low postulated. The propellant burning rate model when coupled with the grain deformation model permits an excellent match between theoretical results and test data for the Titan IIIC, TU455.02, and the first Space Shuttle SRM (DM-1). Analysis of star grain deformation using an experimental model and a finite element model shows the star grain deformation effects for the Space Shuttle to be small in comparison to those of the circular perforated grain. An alternative technique was developed for predicting thrust imbalance without recourse to the Monte Carlo computer program. A scaling relationship used to relate theoretical results to test results may be applied to the alternative technique of predicting thrust imbalance or to the Monte Carlo evaluation. Extended investigation into the effect of strain rate on propellant burning rate leads to the conclusion that the thermoelastic effect is generally negligible for both steadily increasing pressure loads and oscillatory loads.
An orbiter/IUS separation sequence to satisfy the assumed requirements of Shuttle Flight 8 was defined for the purpose of gaining an insight into the flight design software requirements. The key to economical and effective flight design for orbiter/IUS proximity operations is considered to be the capability for rapid and accurate generation of graphical displays that will facilitate not only decision making on the part of the designer, but also lucid documentation of rationale and the resulting design features. The data indicate that (1) an OMS burn is required to attain the necessary velocity without subjecting the IUS and its payload to undue plume impingement, and (2) a departure trajectory that places the orbiter above and behind the IUS at SRM ignition time is preferred over the alternative which would place it below and ahead.
The Materials and Processes Laboratory evaluation of Solid Rocket Boosters (SRB) and Solid Rocket Motors (SRM) candidate material, both in-house and with ocean exposure tests at Panama City and Kennedy Space Center (KSC), Florida is presented. Early sample tests showed excellent seawater corrosion resistance for inconel 718 and titanium 6A1-4V alloys. Considerable corrosion and biofouling occurred with bare 2219-T87 aluminum. Subsequent tests conclusively demonstrated that epoxy coatings prevented corrosion of 2219-T87 aluminum as long as the coatings stays intact. The results and assessment of the series of ocean environmental tests that were conducted are also presented.
Analysis of uncured solid propellant by X-ray fluorescence has been conducted on mixes prepared for four development motors produced for the Space Shuttle SRM Project. X-ray readings for chlorine (ammonium perchlorate) and iron (ferric oxide) were recorded for each mix during processing of the propellant. These values were used to predict burning rates for uncured acceptance, uncured acoustic emission and cured acoustic emission strands. Predicted burning rates all fell within control limits and when compared to actual burning rates, most were within experimental error. The X-ray analysis required one-third the time of current methods and met casting schedules.
A pattern search optimization procedure is used to deduce from test data on the solid rocket boosters of the Space Shuttle the convective heat transfer coefficients between the igniter and main motor combustion gases and the surface of the solid propellant by utilizing a spatial and temporal ignition transient analysis. The 'best' convective coefficients are found which will minimize the overall deviation of the analytical prediction from the ignition transient test data. Computationally, this is achieved by treating the motor in such a way that only four optimization variables must be determined. The resulting coefficients greatly improve the prediction capabilities of the ignition transient analysis for the Space Shuttle SRM.
Recent subscale nozzle tests have identified new and promising carbon phenolic nozzle ablatives which utilize staple rayon, PAN, and pitch based carbon cloth. A 4-inch throat diameter submerged test nozzle designed for the 48-inch Jet Propulsion Laboratory char motor was used to evaluate five different designs incorporating 20 candidate ablatives. Test results indicate that several pitch and PAN-based carbon phenolic ablatives can provide erosion and char performance equivalent or superior to the present continuous rayon-based SRM ablative.
A series of subscale tests are shown to suggest that a lower-cost ablative material than the rayon-based carbon ablative currently used in the Space Shuttle Solid Rocket Motor (SRM) may be used as a substitute. Six such ablatives with outstanding performance characteristics, using spun PAN and continuous pitch and PAN fibers instead of the present, continuous rayon, were identified in the course of tests with HTPB/AL/AP solid propellant grains with a burn time of 12 sec. The test nozzle features an initial throat diameter of 2.2 in. and a 6.1 expansion ratio. In addition to nozzle structural feature drawings, extensive test data tables and propellant formulation and properties tables are provided.
Observations using NORAD radar showed that man made debris exceeds the natural environment for large objects. For short times (a few days to a few weeks) after solid rocket motor (SRM) firings in LEO, man made debris in the microparticle size range also appears to exceed the meteoroid environment. The properties of the debris population between these size regimes is currently unknown as there has been no detector system able to perform the required observations. The alternatives for obtaining data on this currently unobserved segment of the population are assessed.