SEARCH · Search NASA

Results for “stoichiometric ratio”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Shock Tube and Flame Speed Measurements of 2,4,4-Trimethyl-1-Pentene: A Co-Optima Biofuel

Abstract The combustion of 2,4,4-trimethyl-1-pentene (diisobutylene, C8H16), which is a biofuel and a component of surrogate fuels, is examined in this work. Carbon monoxide time–histories and ignition delay times are collected behind reflected shock waves utilizing a shock tube and mid-infrared laser absorption spectroscopy. Measurements were obtained near 10 atm pressure during stoichiometric oxidation of 0.15%C8H16/O2/Ar. Simulated results from chemical kinetic models are provided, and sensitivity analyses are used to discuss differences between models for both ignition delay times and carbon monoxide formation. In addition, laminar burning speeds are obtained at 1 atm, 428 K, and equivalence ratios, phi, between 0.91 and 1.52 inside a spherical chamber facility. Measured burning speeds are found to be less than that of ethanol over the equivalence ratio span. Burning speed measurements are compared to predictions of chemical kinetic mechanisms and are in agreement for the richest conditions; however, at lean conditions, the model predicts a far slower-burning speed. The maximum burning speed occurs at an equivalence ratio of 1.08 with a magnitude of 0.70 m/s. The current work provides the crucial experimental data needed for assessing the feasibility of this biofuel and for the development of future combustion chemical kinetics models.

Energy & Fuels↗

DOE OSTI2024

Next Gen High Efficiency Boosted Engine Development

This work represents an advanced engineering research project partially funded by the U.S. Department of Energy (DOE). Ford Motor Company, FEV North America, and Oak Ridge National Laboratory collaborated to develop a next generation boosted spark ignited engine concept. The project goals, specified by the DOE, were 23% improved fuel economy and 15% reduced weight relative to a 2015 or newer light-duty vehicle. The fuel economy goal was achieved by designing an engine incorporating high geometric compression ratio, high dilution tolerance, low pumping work, and low friction. The increased tendency for knock with high compression ratio was addressed using early intake valve closing (EIVC), cooled exhaust gas recirculation (EGR), an active pre-chamber ignition system, and careful management of the fresh charge temperature. Engine weight reduction measures were implemented throughout the engine system making use of composite materials, advanced manufacturing techniques, and architectural choices. This report outlines the analytical, design, fabrication, and test work conducted for the duration of the project. The combustion system stability, EGR tolerance, and knock resistance were validated on a single cylinder engine. An inline six-cylinder engine was then designed targeting application in the Ford F150. Multi-cylinder engines were produced and tested achieving the target vehicle fuel economy improvement of 23% assessed using measured engine fuel consumption combined with a vehicle drive cycle simulation. Actions were identified and designs were demonstrated to achieve the 15% weight reduction target. This project included items covering a range of technology readiness levels. Some of the technologies explored are production ready, while others were investigated to understand the limitations for what can be achieved in a stoichiometric, gasoline-fueled, spark-ignited internal combustion engine.

42 ENGINEERING↗

DOE OSTI2020

Effects of Turbulence and Temperature Fluctuations on Knock Development in an Ethanol/Air Mixture

The effects of turbulence on knock development and intensity for a thermally inhomogeneous stoichiometric ethanol/air mixture at a representative end-gas autoignition condition in internal combustion engines are investigated using direct numerical simulations with a skeletal reaction mechanism. Two- and three-dimensional simulations are performed by varying the most energetic length scale of temperature, \(l_T\) , and its relative ratio with the most energetic length scale of turbulence, \(l_T/l_e\) , together with two different levels of the turbulent velocity fluctuation, \(u'\) . It is found that \(l_T\) / \(l_e\) and the ratio of ignition delay time to eddy-turnover time, \(\tau _{ig}/\tau _t\) , are the key parameters that control the detonation development. An increase in either \(l_T\) or \(l_e\) enhances the detonation propensity by allowing a longer run-up distance for the detonation development. The characteristic length scale of the temperature field, \(l_T\) , is significantly modified by high turbulence intensity achieved by a large \(l_e\) and \(u'\) . The intense turbulence mixing effectively distributes the initial temperature field to broader scales to support the developing detonation waves, thereby increasing the likelihood of the detonation formation. On the contrary, high turbulence intensity with a short mixing time scale, achieved by a small \(l_e\) and a large \(u'\) , reduces the super-knock intensity attributed to the finer broken-up structures of detonation waves. Either \(\tau _{ig}/\tau _t\) less than unity or \(l_e = l_T\) even with a large \(u'\) is found to have no significant effect on super-knock mitigation. Finally, high turbulent intensity may induce high-pressure spikes comparable to the von Neumann spike. Overall, increased temperature and pressure by combustion heating, noticeably after the peak of heat release rate, significantly enhance the collision and interaction of multiple emerging autoignition fronts near the ending combustion process, resulting in localized high-pressure spikes.

42 ENGINEERING↗

DOE OSTI2024

Mechanistically Guided Materials Chemistry: Synthesis of Ternary Nitrides, CaZrN 2 and CaHfN 2

Recent computational studies have predicted many new ternary nitrides, revealing synthetic opportunities in this underexplored phase space. However, synthesizing new ternary nitrides is difficult, in part because intermediate and product phases often have high cohesive energies that inhibit diffusion. Here, we report the synthesis of two new phases, calcium zirconium nitride (CaZrN 2 ) and calcium hafnium nitride (CaHfN 2 ), by solid state metathesis reactions between Ca 3 N2 and MCl 4 (M = Zr, Hf). Although the reaction nominally proceeds to the target phases in a 1:1 ratio of the precursors via Ca 3 N 2 + MCl4 → CaMN 2 + 2 CaCl 2 , reactions prepared this way result in Ca-poor materials (Ca x M 2–x N2, x < 1). A small excess of Ca 3 N 2 (ca. 20 mol %) is needed to yield stoichiometric CaMN 2 , as confirmed by high-resolution synchrotron powder X-ray diffraction. In situ synchrotron X-ray diffraction studies reveal that nominally stoichiometric reactions produce Zr 3+ intermediates early in the reaction pathway, and the excess Ca 3 N 2 is needed to reoxidize Zr 3+ intermediates back to the Zr 4+ oxidation state of CaZrN 2 . Analysis of computationally derived chemical potential diagrams rationalizes this synthetic approach and its contrast from the synthesis of MgZrN 2 . These findings additionally highlight the utility of in situ diffraction studies and computational thermochemistry to provide mechanistic guidance for synthesis.

36 MATERIALS SCIENCE↗

DOE OSTI2026

A divergent synthetic route to functional copolymer libraries via modular polymers

High-throughput polymer synthesis enables rapid exploration of chemical space but remains limited by batch-to-batch inconsistencies that can obscure structure–property relationship trends. To address this challenge, we developed a synthetic approach to produce multifunctional copolymers using post-polymerization modification of activated ester modular polymers with commercially available amines. Easily derivitized parent polymers—poly(tetrafluorophenyl acrylate) and poly(tetrafluorophenyl styrene sulfonate)—were synthesized by RAFT polymerization to yield single polymer batches containing highly reactive tetrafluorophenyl esters or sulfonate esters on each repeat unit. Tuning post-polymerization modification reaction conditions enabled the addition of sub-stoichiometric amounts of amines (relative to the repeat unit) to yield partially functionalized intermediates that could then be further derivatized. Reaction monitoring by 19 F NMR spectroscopy confirmed good control over these sequential post-polymerization modifications. This synthetic route produced a variety of copolymers with defined comonomer ratios while preserving the underlying polymer structure (degree of polymerization, dispersity, tacticity) for both the acrylate and styrene sulfonate backbones. We further applied this approach in a divergent manner to create a small library of structurally distinct copolymers from a single parent batch in three synthetic steps. This modular, divergent synthesis demonstrates a general route to structurally consistent copolymer libraries that enable systematic studies of structure–property relationships and can accelerate functional materials discovery.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

An experimental and kinetic modeling study of NO x sensitization on methane autoignition and oxidation

An experimental and kinetic modeling study of the influence of NO x (i.e. NO 2 , NO and N 2 O) addition on the ignition behavior of methane/‘air’ mixtures is performed. Ignition delay time measurements are taken in a rapid compression machine (RCM) and in a shock tube (ST) at temperatures and pressures ranging from 900–1500 K and 1.5–3.0 MPa, respectively for equivalence ratios of 0.5–2.0 in ‘air’. The conditions chosen are relevant to spark ignition and homogeneous charge compression ignition engine operating conditions where exhaust gas recirculation can potentially add NO x to the premixed charge. The RCM measurements show that the addition of 200 ppm NO 2 to the stoichiometric CH 4 /oxidizer mixture results in a factor of three increase in reactivity compared to the baseline case without NOx for temperatures in the range 600–1000 K. However, adding up to 1000 ppm N 2 O does not show any appreciable effect on the measurements. The promoting effect of NO 2 was found to increase with temperature in the range 950–1150 K, while the sensitization effect decreases at higher pressures. The experimental results measured are simulated using NUIGMech1.2 comprising an updated NO x sub-chemistry in this work. A kinetic analysis indicates that the competition between the reactions ĊH 3 + NO 2 ↔ CH 3 Ȯ + NO and ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), the former being a propagation reaction and the latter being a termination reaction governs NO x sensitization on CH 4 ignition. Recent calculations by Matsugi and Shiina (A. Matsugi, H. Shiina, J. Phys. Chem. A. 121 (2017) 4218–4224) for the nitromethane formation reaction CH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M), together with the recently calculated rate constants for HONO/HNO 2 reactions significantly improve ignition delay time predictions in the temperature range 600–1000 K. Furthermore, the experiments with NO addition reveal a non-monotonous sensitization impact on CH 4 ignition at lower temperatures with NO initially acting as an inhibitor at low NO concentrations and then as a promoter as NO concentrations increase in the mixture. This non-monotonous trend is attributed to the role of the chain-termination reaction ĊH 3 + NO 2 (+M) ↔ CH 3 NO 2 (+M) and the impact of NO on the transition to the chain-branching steps CH 2 O + HȮ 2 ↔ HĊO + H 2 O 2 , H 2 O 2 (+M) ↔ ȮH + ȮH (+M), HĊO ↔ CO + Ḣ followed by CO + O 2 ↔ CO 2 + Ö and Ḣ + O 2 ↔ Ö + ȮH. NUIGMech1.2 is systematically validated against the new ignition delay measurements taken here together with species measurements and high temperature ignition delay time data available in the literature for CH 4 /oxidizer mixtures diluted with NO 2 /N 2 O/NO and is observed to accurately capture the sensitization trends.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2024

Stoichiometric Lanthanide Compounds with Diglycolamides: A Synthetic Approach toward Understanding Rare-Earth Speciation in Solution

A fundamental understanding of coordination chemistry across the lanthanide series is essential for explaining the chemical behavior of rare-earth metals in complex liquid–liquid extraction processes. Probing the exact bonding between the extractant and the metal is sometimes done through the synthesis of solid-state compounds that can serve as models for metal speciation in solution. In the case of diglycolamide (DGA), a commonly used neutral diamide extractant, extensive studies identify the stepwise formation of 1:1 [Ln(DGA)(H 2 O) 6 ] 3+ , 1:2 [Ln(DGA) 2 (H 2 O) 3 ] 3+ , and 1:3 [Ln(DGA) 3 ] 3+ complexes in solution. The crystallographic reports, however, exclusively show a 1:3 [Ln(DGA) 3 ] 3+ moiety in the solid state, while the structures of 1:1 and 1:2 complexes are yet to be isolated and comprehensively studied. In this work, we report the synthesis and characterization of three new families of stoichiometric N,N,N′,N’ -tetramethyldiglycolamide (TMDGA) compounds: [Ln(TMDGA)(H 2 O) 5 Cl]Cl 2 ·2H 2 O, [Ln(TMDGA) 2 (H 2 O) 3 ]Cl 3 ·3H 2 O, and [Ln(TMDGA) 3 ]Cl 3 ·7H 2 O, where Ln = Nd, Eu, Gd, with Ln:TMDGA ratios of 1:1, 1:2, and 1:3, respectively. Further, the compounds have been analyzed using vibrational spectroscopy (both Raman and FT-IR), as well as variable temperature fluorescence spectroscopy. A spectrophotometric titration of Eu(III) was performed to confirm the presence of the [Eu(TMDGA) n ] 3+ ( n = 1, 2, and 3) species in solution and to compare the individual solid-state emission spectra to their respective analogues in solution.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Effects of Glymes on the Distribution of Mg(B 10 H 10 ) and Mg(B 12 H 12 ) from the Thermolysis of Mg(BH 4 ) 2

We examined the effects of concentrations and identities of various glymes, from monoglyme up to tetraglyme, on H 2 release from the thermolysis of Mg(BH 4 ) 2 at 160–200 °C for 8 h. 11 B NMR analysis shows major products of Mg(B 10 H 10 ) and Mg(B 12 H 12 ); however, their relative ratio is highly dependent both on the identity and concentration of the glyme to Mg(BH 4 ) 2 . Selective formation of Mg(B 10 H 10 ) was observed with an equivalent of monoglyme and 0.25 equivalent of tetraglyme. However, thermolysis of Mg(BH 4 ) 2 in the presence of stoichiometric or greater equivalent of glymes can lead to unselective formation of Mg(B 10 H 10 ) and Mg(B 12 H 12 ) products or inhibition of H 2 release.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1990

Low NO(x) potential of gas turbine engines

The purpose is to correlate emission levels of gas turbine engines. The predictions of NO(x) emissions are based on a review of the literature of previous low NO(x) combustor programs and analytical chemical kinetic calculations. Concepts included in the literature review consisted of lean-premixed-prevaporized (LPP), rich burn/quick quench/lean burn (RQL), and direct injection. The NO(x) emissions were found to be an exponential function of adiabatic combustion temperature over a wide range of inlet temperatures, pressures and (lean) fuel-air ratios. A simple correlation of NO(x) formation with time was not found. The LPP and direct injection (using gaseous fuels) concepts have the lowest NO(x) emissions of the three concepts. The RQL data has higher values of NO(x) than the LPP concept, probably due to the stoichiometric temperatures and NO(x) production that occur during the quench step. Improvements in the quick quench step could reduce the NO(x) emissions to the LPP levels. The low NO(x) potential of LPP is offset by the operational disadvantages of its narrow stability limits and its susceptibility to autoignition/flashback. The Rich-Burn/Quick-Quench/Lean-Burn (RQL) and the direct injection concepts have the advantage of wider stability limits comparable to conventional combustors.

Tacina, Robert R.↗

NASA NTRS1993

Method of forming silicon structures with selectable optical characteristics

Silicon and metal are coevaporated onto a silicon substrate in a molecular beam epitaxy system with a larger than stoichiometric amount of silicon so as to epitaxially grow particles of metal silicide embedded in a matrix of single crystal epitaxially grown silicon. The particles interact with incident photons by resonant optical absorption at the surface plasmon resonance frequency. Controlling the substrate temperature and deposition rate and time allows the aspect ratio of the particles to be tailored to desired wavelength photons and polarizations. The plasmon energy may decay as excited charge carriers or phonons, either of which can be monitored to indicate the amount of incident radiation at the selected frequency and polarization.

Fathauer, Robert W.↗

NASA NTRS1994

Optical detector having a plurality of matrix layers with cobalt disilicide particles embedded therein

Silicon and metal are coevaporated onto a silicon substrate in a molecular beam epitaxy system with a larger than stoichiometric amount of silicon so as to epitaxially grow particles of metal silicide embedded in a matrix of single crystal epitaxially grown silicon. The particles interact with incident photons by resonant optical absorption at the surface plasmon resonance frequency. Controlling the substrate temperature and deposition rate and time allows the aspect ratio of the particles to be tailored to desired wavelength photons and polarizations. The plasmon energy may decay as excited charge carriers of phonons, either of which can be monitored to indicate the amount of incident radiation at the selected frequency and polarization.

Fathauer, Robert W.↗

NASA NTRS1997

Optimization of Jet Mixing Into a Rich, Reacting Crossflow

Radial jet mixing of pure air into a fuel-rich, reacting crossflow confined to a cylindrical geometry is addressed with a focus on establishing an optimal jet orifice geometry. The purpose of this investigation was to determine the number of round holes that most effectively mixes the jets with the mainstream flow, and thereby minimizes the residence time of near-stoichiometric and unreacted packets. Such a condition might reduce pollutant formation in axially staged, gas turbine combustor systems. Five different configurations consisting of 8, 10, 12, 14, and 18 round holes are reported here. An optimum number of jet orifices is found for a jet-to-mainstream momentum-flux ratio (J) of 57 and a mass-flow ratio (MR) of 2.5. For this condition, the 14-orifice case produces the lowest spatial unmixedness and the most uniformly-distributed species concentrations and temperature profiles at a plane located one duct diameter length from the jet orifice inlet.

Leong, M. Y.↗

DOE OSTI2024

Intermetallic Ni 3 Ga 1 Catalyst for Efficient Ammonia Reforming of Light Alkane

Ammonia reforming of light alkane is conventionally employed for HCN production where coproduct H 2 is burned for heating owing to the high reaction temperature (1200 °C) of such a highly endothermic process. Here, in this study, we show that a Ni 3 Ga 1 intermetallic compound (IMC) catalyst is highly efficient for such a reaction, realizing efficient conversion of C1–C3 alkanes at 575–750 °C. This makes it feasible for on-purpose CO x -free H 2 production assuming that ammonia, as an H 2 carrier, is ubiquitously available from renewable energy. At 650 °C and an alkane/ammonia ratio of 1/2, ethane and propane conversion of ~20% and methane conversion of 13% were obtained (with nearly 100% HCN selectivity for methane and ethane) over the unsupported Ni 3 Ga 1 IMC, which also shows high stability due to the absence of coke deposition. This breakthrough is achieved by employing a stoichiometric Ni 3 Ga 1 mixed oxalate solid solution as the precursor for the Ni 3 Ga 1 IMC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Metal–insulator transition tuned by oxygen vacancy migration across TiO2/VO2 interface

Abstract Oxygen defects are essential building blocks for designing functional oxides with remarkable properties, ranging from electrical and ionic conductivity to magnetism and ferroelectricity. Oxygen defects, despite being spatially localized, can profoundly alter global properties such as the crystal symmetry and electronic structure, thereby enabling emergent phenomena. In this work, we achieved tunable metal–insulator transitions (MIT) in oxide heterostructures by inducing interfacial oxygen vacancy migration. We chose the non-stoichiometric VO 2-δ as a model system due to its near room temperature MIT temperature. We found that depositing a TiO 2 capping layer on an epitaxial VO 2 thin film can effectively reduce the resistance of the insulating phase in VO 2 , yielding a significantly reduced R OFF /R ON ratio. We systematically studied the TiO 2 /VO 2 heterostructures by structural and transport measurements, X-ray photoelectron spectroscopy, and ab initio calculations and found that oxygen vacancy migration from TiO 2 to VO 2 is responsible for the suppression of the MIT. Our findings underscore the importance of the interfacial oxygen vacancy migration and redistribution in controlling the electronic structure and emergent functionality of the heterostructure, thereby providing a new approach to designing oxide heterostructures for novel ionotronics and neuromorphic-computing devices.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Compressive strain turns 𝑠 ± - into 𝑑-wave pairing in a one-unit-cell La 3 ⁢Ni 2 ⁢O 7 thin film via substrate-induced hole doping

Motivated by recent reports of ambient-pressure superconductivity in La 3 ⁢Ni 2⁢ O 7 films grown on LaSrAlO 4 , we investigate the superconducting instability in a one-unit-cell (1UC) thin film using ab initio and random-phase approximation techniques. Compared to the high-pressure bulk system, the ratio of interlayer 𝑑 3⁢𝑧 2 −𝑟 2 hopping to intralayer 𝑑 𝑥 2 −𝑦 2 hopping is suppressed in the 1UC thin film, and the crystal-field splitting of the 𝑒 𝑔 orbitals is increased. Here, our calculation indicates that spin-fluctuation-driven pairing correlations are weak for the stoichiometric case at ambient pressure, but increase significantly under hole doping. The leading pairing symmetry is also found to change by hole doping. Specifically, we obtain a leading 𝑑 𝑥 2 −𝑦 2 pairing state at moderate hole doping, followed by a 𝑑 𝑥⁢𝑦 state at higher doping. These states are driven by intraband spin-fluctuation scattering within the 𝛾 hole pocket centered around the 𝑀 point, and arise primarily from states in the Ni layer farther from the substrate. These results strongly suggest that the thin-film superconducting samples are hole-doped and that pairing in this system predominantly arises in the layer, as opposed to the interlayer pairing in the pressurized bulk system.

Zhang, Yang [Oak Ridge National Laboratory (ORNL),↗

DOE OSTI2026

Nanocluster Rearrangement Forms a Family of Ordered Cerium–Titanium Bimetallic Metal–Organic Frameworks with Three Different Nodes, Nanocavities, and Thermal Stabilities

Metal–organic frameworks (MOFs) provide a versatile platform for incorporating multiple metal ions within a single crystalline framework, yet achieving spatial and stoichiometric order in heterometallic nodes remains a synthetic challenge. Building on our previously reported, highly thermally stable Ce/Ti bimetallic MOF NU-3000, we identified and isolated two additional crystalline phases, NU-2998 and NU-2999, that arise from the same Ce/Ti nanocluster precursor under modified solvothermal conditions. Systematic variation of reaction temperature, time, solvent ratio, and modulator concentration directs the assembly of these distinct frameworks. Structural analysis and comprehensive characterization studies reveal that these MOFs each feature an unreported nodal geometry with nanocavities of different sizes. NU-2998 even adopts an unreported topology, denoted nui , that features an elongated pore spanning 4 nm. Together, these findings establish a synthesis route that starts with a nanocluster and ends with a set of bimetallic MOFs, offering a glimpse into the pathway-dependent assembly of multimetallic porous materials. Finally, we evaluated the thermal stability of each additional analogue and compared them to NU-3000, providing further insight into material stability. NU-3000 maintained the highest thermal stability and was evaluated as a catalyst for CO oxidation at elevated temperatures.

bimetallic MOFs↗

DOE OSTI2020

An investigation of the long-range and local structure of sub-stoichiometric zirconium carbide sintered at different temperatures

ZrC 1-x (sub-stoichiometric zirconium carbide), a group IV transition metal carbide, is being considered for various high temperature applications. Departure from stoichiometry changes the thermo-physical response of the material. Reported thermo-physical properties exhibit, in some cases, a degree of scatter with one likely contributor to this being the uncertainty in the C/Zr ratio of the samples produced. Conventional, methods for assigning C/Zr to samples are determined either by nominal stochiometric ratios or combustion carbon analysis. In this study, a range of stoichiometries of hot-pressed ZrC 1-x were examined by SEM, XRD, Raman spectroscopy and static 13 C NMR spectroscopy and used as a basis to correct the C/Zr. Graphite, amorphous, and ZrC 1-x carbon signatures are observed in the 13 C NMR spectra of samples and are determined to vary in intensity with sintering temperature and stoichiometry. In this study a method is outlined to quantify the stoichiometry of ZrC 1-x and free carbon phases, providing an improvement over the sole use and reliance of widely adopted bulk carbon combustion analysis. We report significantly lower C/Zr values determined by 13 C NMR analysis compared with carbon analyser and nominal methods. Furthermore, the location of carbon disassociated from the ZrC 1-x structure is analysed using SEM and Raman spectroscopy.

36 MATERIALS SCIENCE↗

NASA NTRS1976

Design study of a gas turbine combustor with heat recirculation

A means of avoiding stoichiometric combustion, reducing emissions, and yet providing stable burning for lean mixtures is based on the use of heat recirculation rather than flow recirculation. This paper is concerned with the calculations of the design parameters of a gas turbine combustor with heat exchanger to produce the desired preheat temperature. The combustor inlet temperature, maximum temperature, equivalence ratio and recirculated heat are determined by thermodynamic analysis. The heat transfer analysis then provides the dimensions of the system to produce the predetermined boundary conditions. It is indicated that practical combustor design may be feasible for reactant mixtures as low as equivalence ratio 0.2.

Ganji, A.↗