Search NASA⌕ Search

SEARCH · Search NASA

Results for “streamline”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

STME - Streamlining the engine of change

The key to the success of the NASA Space Transportation Main Engine (STME) is its enhanced reliability and reduced costs, rather than enhanced performance and reduced weight. Reliability and cost improvements derive from the design of an engine with fewer components, wider operating margins, conventional materials, and innovative manufacturing techniques; this is exemplified by the STME's combustion chamber, in which the structural jacket and all minifolds are cast as a single piece. 'Platelet' technology is under active consideration as a basis for the nozzle design. The use of hydrostatic bearings in both the turbine and pump ends of the STME turbopump will eliminate bearing-life limitations.

Smelser, Jerry W.↗
NASA NTRS1992

Streamline curvature in supersonic shear layers

Results of an experimental investigation in which a curved shear layer was generated between supersonic flow from a rectangular converging/diverging nozzle and the freestream in a series of open channels with varying radii of curvature are reported. The shear layers exhibit unsteady large-scale activity at supersonic pressure ratios, indicating increased mixing efficiency. This effect contrasts with supersonic flow in a straight channel, for which no large-scale vortical structure development occurs. Curvature must exceed a minimum level before it begins to affect the dynamics of the supersonic shear layer appreciably. The curved channel flows are compared with reference flows consisting of a free jet, a straight channel, and wall jets without sidewalls on a flat and a curved plate.

Kibens, V.↗
NASA NTRS1937

Fuselage-drag tests in the variable-density wind tunnel: streamline bodies of revolution, fineness ratio of 5

Results are presented of the drag tests of six bodies of revolution with systematically varying shapes and with a fineness ratio of 5. The forms were derived from source-sink distributions, and formulas are presented for the calculation of the pressure distribution of the forms. The tests were made in the N.A.C.A. variable-density tunnel over a range of values of Reynolds number from about 1,500,000 to 25,000,000. The results show that the bodies with the sharper noses and tails have the lowest drag coefficients, even when the drag coefficients are based on the two-thirds power of the volume. The data shows the most important single characteristic of the body form to be the tail angle, which must be fine to obtain low drag.

Abbott, Ira H↗
NASA NTRS1941

Relief of Residual Stress in Streamline Tie Rods by Heat Treatment

About two-thirds of the residual stress in cold-worked SAE 1050 steel tie rods was relieved by heating 30 minutes at 600 degrees Fahrenheit. Cold-worked austenitic stainless-steel tie rods could be heated at temperatures up to 1000 degrees Fahrenheit without lowering the important physical properties. The corrosion resistance, in laboratory corrosion test, of straight 18:8 and titanium-treated 18:8 materials appeared to be impaired after heating at temperatures above 800 degrees or 900 degrees fahrenheit. Columbium-treated and molybdenum-treated 18:8 steel exhibited improved stability over a wide range of temperatures. Tie rods of either material could be heated 30 minutes with safety at any temperature up to 1000 degrees Fahrenheit. At this temperature most of the residual stress would be relieved.

Pollard, R E↗
NASA NTRS1947

The Streamline Pattern in the Vicinity of an Oblique Airfoil

A method for determining the streamwise flow pattern of a nonviscous incompressible fluid about an oblique airfoil from the corresponding flow pattern about the airfoil in normal position is presented and illustrated in two examples. The method can be extended to account approximately for compressibility effects by applying the Prandtl-Glauert correction factor to the flow pattern that is normal to the leading edge of the airfoil. The method is expected to be useful in determining the shape of a fuselage or nacelle having a minimum of interference with the flow over a swept-back wing.

Watkins, Charles E↗