Search NASA⌕ Search

SEARCH · Search NASA

Results for “traversibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS2011

Teleoperated Marsupial Mobile Sensor Platform Pair for Telepresence Insertion Into Challenging Structures

A platform has been developed for two or more vehicles with one or more residing within the other (a marsupial pair). This configuration consists of a large, versatile robot that is carrying a smaller, more specialized autonomous operating robot(s) and/or mobile repeaters for extended transmission. The larger vehicle, which is equipped with a ramp and/or a robotic arm, is used to operate over a more challenging topography than the smaller one(s) that may have a more limited inspection area to traverse. The intended use of this concept is to facilitate the insertion of a small video camera and sensor platform into a difficult entry area. In a terrestrial application, this may be a bus or a subway car with narrow aisles or steep stairs. The first field-tested configuration is a tracked vehicle bearing a rigid ramp of fixed length and width. A smaller six-wheeled vehicle approximately 10 in. (25 cm) wide by 12 in. (30 cm) long resides at the end of the ramp within the larger vehicle. The ramp extends from the larger vehicle and is tipped up into the air. Using video feedback from a camera atop the larger robot, the operator at a remote location can steer the larger vehicle to the bus door. Once positioned at the door, the operator can switch video feedback to a camera at the end of the ramp to facilitate the mating of the end of the ramp to the top landing at the upper terminus of the steps. The ramp can be lowered by remote control until its end is in contact with the top landing. At the same time, the end of the ramp bearing the smaller vehicle is raised to minimize the angle of the slope the smaller vehicle has to climb, and further gives the operator a better view of the entry to the bus from the smaller vehicle. Control is passed over to the smaller vehicle and, using video feedback from the camera, it is driven up the ramp, turned oblique into the bus, and then sent down the aisle for surveillance. The demonstrated vehicle was used to scale the steps leading to the interior of a bus whose landing is 44 in. (.1.1 m) from the road surface. This vehicle can position the end of its ramp to a surface over 50 in. (.1.3 m) above ground level and can drive over rail heights exceeding 6 in. (.15 cm). Thus configured, this vehicle can conceivably deliver the smaller robot to the end platform of New York City subway cars from between the rails. This innovation is scalable to other formulations for size, mobility, and surveillance functions. Conceivably the larger vehicle can be configured to traverse unstable rubble and debris to transport a smaller search and rescue vehicle as close as possible to the scene of a disaster such as a collapsed building. The smaller vehicle, tethered or otherwise, and capable of penetrating and traversing within the confined spaces in the collapsed structure, can transport imaging and other sensors to look for victims or other targets.

Krasowski, Michael J.↗
NASA NTRS2015

Fluvial to Lacustrine Facies Transitions in Gale Crater, Mars

NASA's Curiosity rover has documented predominantly fluvial sedimentary rocks along its path from the landing site to the toe of the Peace Vallis alluvial fan (0.5 km to the east) and then along its 8 km traverse across Aeolis Palus to the base of Aeolis Mons (Mount Sharp). Lacustrine facies have been identified at the toe of the Peace Vallis fan and in the lowermost geological unit exposed on Aeolis Mons. These two depositional systems provide end members for martian fluvial/alluvial-lacustrine facies models. The Peace Vallis system consisted of an 80 square kilometers alluvial fan with decimeter-thick, laterally continuous fluvial sandstones with few sedimentary structures. The thin lacustrine unit associated with the fan is interpreted as deposited in a small lake associated with fan runoff. In contrast, fluvial facies exposed over most of Curiosity's traverse to Aeolis Mons consist of sandstones with common dune-scale cross stratification (including trough cross stratification), interbedded conglomerates, and rare paleochannels. Along the southwest portion of the traverse, sandstone facies include south-dipping meter-scale clinoforms that are interbedded with finer-grained mudstone facies, interpreted as lacustrine. Sedimentary structures in these deposits are consistent with deltaic deposits. Deltaic deposition is also suggested by the scale of fluvial to lacustrine facies transitions, which occur over greater than 100 m laterally and greater than 10 m vertically. The large scale of the transitions and the predicted thickness of lacustrine deposits based on orbital mapping require deposition in a substantial river-lake system over an extended interval of time. Thus, the lowermost, and oldest, sedimentary rocks in Gale Crater suggest the presence of substantial fluvial flow into a long-lived lake. In contrast, the Peace Vallis alluvial fan onlaps these older deposits and overlies a major unconformity. It is one of the youngest deposits in the crater, and requires only short-lived, transient flows.

Sumner, Dawn Y.↗
NASA NTRS2015

Distinct Igneous APXS Rock Compositions on Mars from Pathfinder, MER and MSL

The alpha particle x-ray spectrometer (APXS) on all four Mars Rovers returned geochemical data from about 1000 rocks and soils along the combined traverses of over 50 kilometers. Here we discuss rocks likely of igneous origin, which might represent source materials for the soils and sediments identified along the traverses. Adirondack-type basalts, abundant in the plains of Gusev Crater, are primitive, olivine bearing basalts. They resemble in composition the basaltic soils encountered at all landing sites, except the ubiquitous elevated S, Cl and Zn in soils. They have been postulated to represent closely the average Martian crust composition. The recently identified new Martian meteorite Black Beauty has similar overall geochemical composition, very distinct from the earlier established SNC meteorites. The rim of the Noachian crater Endeavour, predating the sulfate-bearing Burns formation at Meridiani Planum, also resembles closely the composition of Adirondack basalts. At Gale Crater, the MSL Curiosity rover identified a felsic rock type exemplified by the mugearitic float rock JakeM, which is widespread along the traverse at Gale. While a surprise at that time, possibly related more evolved, alkaline rocks had been previously identified on Mars. Spirit encountered the Wishstone rocks in the Columbia Hills with approx. 6% Na2O+K2O, 15 % Al2O3 and low 12% FeO. Pathfinder rocks with elevated K and Na and >50% SiO2 were postulated to be andesitic. Recently Opportunity encountered the rock JeanBaptisteCharbonneau with >15% Al2O3, >50% SiO2 and approx. 10% FeO. A common characteristic all these rocks is the very low abundance of Cr, Ni and Zn, and an Fe/Mn ratio of about 50, indicating an unaltered Fe mineralogy. Beside these likely igneous rock types, which occurred always in several rocks, a few unique rocks were encountered, e.g. Bounce Rock, a pyroxene-bearing ejecta rock fragment resembling the Shergottite EETA 79001B meteorite. The APXS data can be used to relate the findings of all 4 landing sites, constrain the water to rock ratio of sediments or imply source rock provenance. Beyond that the capability to quantify important volatile elements like P, S, Cl, and Br have provided new insights into the chemistry and the environment present during the formation of the sediments.

Gellert, Ralf↗
NASA NTRS2015

Geologic Investigations Spurred by Analog Testing at the 7504 Cone-SP Mountain Area of the San Francisco Volcanic Field

The SP Mountain area of the San Francisco Volcanic Field, AZ, has been used as an analog mission development site for NASA since 1998. This area consists of basaltic cinder cones, lava flows and maar craters that have been active since mid-Miocene, with the youngest events occurring within the last 10,000 years. The area has been used because its geologic and topographic resemblance to lunar and Martian terrains provides an ideal venue for testing hardware and science operations practices that might be employed on planetary surfaces, as well as training astronauts in field geology. Analog operations have often led to insights that spurred new scientific investigations. Most recently, an investigation of the 7504 cone was initiated due to perceptions that Apollo-style traverse plans executed during the Desert RATS 2010 mission had characterized the area incorrectly, leading to concerns that the Apollo traverse planning process was scientifically flawed. This investigation revealed a complex history of fissure eruptions of lava and cinders, cinder cone development, a cone-fill-and-spill episode, extensive rheomorphic lava flow initiation and emplacement, and cone sector collapse that led to a final lava flow. This history was not discernible on pre-RATS mission photogeology, although independent analysis of RATS 2010 data and samples develped a "75% complete solution" that validated the pre-RATS mission planning and Apollo traverse planning and execution. The study also pointed out that the development of scientific knowledge with time in a given field area is not linear, but may follow a functional form that rises steeply in the early period of an investigation but flattens out in the later period, asymptotically approaching a theoretical "complete knowledge" point that probably cannot be achieved. This implies that future human missions must be prepared to shift geographic areas of investigation regularly if significant science returns are to be forthcoming.

Eppler, Dean B.↗
NASA NTRS2016

Al-Mg Isotope Study of Allende 5241

The defining characteristic of type B1 CAIs is a large (.5- 3mm) concentric melilite mantle [1]. In [2] we presented two isochrons from separate traverses across the melilite mantle of Allende EK 459-5-1. The primary petrographic differences between the traverses was the preservation of strong oscillatory zoning. The traverse that crossed the distinctive oscillatory zone produced a pristine internal isochron, while the other that did not have a strongly preserved oscillatory zone produced a disturbed isochron indicated by more scatter (higher MSWD) and a positive (delta)26Mg* intercept. The implication simply being that the oscillatory zone may represent varying conditions during the mantle formation event. We targeted a similar texture in Allende 5241 using the same methodology in an attempt to achieve similar results.

Kerekgyarto, A. G.↗
NASA NTRS2016

Igneous and Sedimentary Compositions from Four Landing Sites on Mars from the Alpha Particle X-Ray Spectrometer (APXS)

The APXS - supported and promoted strongly by Heinrich Waenke - on all four Mars Rovers has returned compositional data from about 1000 rocks and soil targets along the combined traverses of over 60 kilometers. Providing precise and accurate bulk chemistry with typically 16 quantified elements, the APXS is a powerful and versatile tool that when combined with the ability to traverse to key rocks and soils has provided critical information needed to understand the geologic evolution of Mars. APXS data allow comparisons among landing sites, provide ground truth for orbiters and connections back to SNC meteorites. The soils and dust are basaltic in character and represent the average Mars composition similar to Adirondack basalts from Gusev crater but with unambiguous elevated and correlated S, Cl and Zn contents. At all four landing sites the APXS found several rocks with a felsic composition. The similarity is best assessed in a logarithmic ratio plot of rock normalized to the average soil composition (Fig.1). High alkaline, Al, and low Mg, Fe, low S, Cl and Ni, Zn as well as an Fe/Mn ratio of approximately 50 indicate a likely unaltered and igneous origin. Sediments, e.g. the Burns formation, with approximately 25 wt% SO3 at Meridiani Planum have been documented over 10s of kilometers (Fig. 2). This formation is compositionally homogeneous, but showing the removal of MgSO4 and a threefold increase in Cl downhill in 2 craters. The degraded rim of the Noachian crater Endeavour resembles average Mars crust, with local Ca, Mg and Fe sulfate alteration and elevated Mn, some felsic rocks, and high Al, Si and low Fe rocks, possibly indicating clays. Unusual soils at Gusev crater in the area surrounding Home Plate include some very rich in ferric sulfate salts (up to 35 wt% SO3) and some with 90% wt% SiO2, possibly indicating fumerolic activities. Rocks in the Columbia Hills show significant signs of alteration including elevated S, Cl and Br in the abraded interior. At Gale Crater, mudstones with approximately 20% clay, less than 1% SO3 and overall average Mars composition indicate a former habitable environment with low acidity. A remarkable diversity of compositions was found during Curiosity's traverses, which likely stems from material influx from the northern Gale rim. At Pahrump, the base of Mount Sharp, a homogeneous mudstone with lower Mg and Ca was encountered. The composition of this Murray unit can be traced over several kilometers with smooth trends of higher Fe/Mn and lower soluble trace elements Ni and Zn at higher elevation. The likely aeolian Stimson formation with average Mars crustal composition intersects in several places in sharp contact with the Murray formation. Both units show local alteration halos with highly elevated SiO2 of up to 75%, usually correlated with increase in Ti and often P.

Gellert, R.↗
NASA NTRS2016

Future Exploration of the South Pole as Enabled by the Lunar Reconnaissance Orbiter

The Lunar Reconnaissance Orbiter (LRO) launched in 2009 to collect the dataset required for future surface missions and to answer key questions about the lunar surface environment. In the first seven years of operations, the Lunar Reconnaissance Orbiter Camera (LROC) acquired over a million images of the lunar surface and collected key stereo observations for the production of meter-scale digital terrain models. Due to the configuration of the LRO orbit, LROC and the other onboard instruments have the opportunity to acquire observations at or near the poles every two hours. The lunar south polar region is an area of interest for future surface missions due to the benign thermal environment and areas of near-continuous illumination. These persistently illuminated regions are also adjacent to permanently shadowed areas (e.g. floors of craters and local depressions) that are of interest to both scientists and engineers prospecting for cold-trapped volatiles on or near the surface for future in situ resource utilization. Using a terramechanics model based on surface properties derived during the Apollo and Luna missions, we evaluated the accessibility of different science targets and the optimal traverse paths for a given set of waypoints. Assuming a rover that relies primarily on solar power, we identified a traverse that would keep the rover illuminated for 94.43% of the year between 1 January 2021 and 31 December 2021. Throughout this year-long period, the longest eclipse endured by the rover would last only 101 hours and the rover would move a total of 22.11 km with an average speed of 2.5 m/hr (max speed=30 m/hr). During this time the rover would be able to explore a variety of targets along the connecting ridge between Shackleton and de Gerlache craters. In addition to the southern polar regions, we are also examining traverses around other key exploration sites such as Marius Hills, Ina-D, Rima Parry, and the Mairan Domes in efforts to aid future mission planners and assess the requirements for future roving prospectors (e.g., maximum speed, maximum slope, etc.).

Speyerer, Emerson J.↗
NASA NTRS2015

Development of the Resource Prospector Planetary Rover

The Resource Prospector (RP) is an In-­‐Situ Resource Utilization (ISRU) lunar rover mission under study by NASA. RP is planned to launch in 2020 to prospect for subsurface volatiles and to extract oxygen from lunar regolith. The mission will address several of NASA's "Strategic Knowledge Gaps" for lunar exploration. The mission will also address the Global Exploration Roadmap's strategic goal of using local resources for human exploration. The distribution of lunar subsurface volatiles drives the mission requirement for mobility. The spatial distribution is hypothesized to be governed by impact cratering with the top 0.5 m being patchy at scales of 100 m. The mixing time scale increases with depth (less frequent larger impacts). Consequently, increased mobility reduces the depth requirement for sampling. The target RP traverse will extend 1 km radially from the landing site to sample craters of varying sizes. Sampling craters with different ages will reveal possible volatile emplacement history. In 1 Ga, approximately 60-­70 craters of 10 m diameter form per km2. Thus, the rover will need to sample at least ten of these craters, which may require a total traverse path length of 2-­‐3 km. During 2014-­2015, we developed an initial prototype rover for RP. The current design is a solar powered, four-­wheeled vehicle, with hub motor drive, offset four wheel steering, and active suspension. Active suspension provides capabilities including changing vehicle ride height, traversing comparatively large obstacles, and controlling load on the wheels. All-­wheel steering enables the vehicle to point arbitrarily while roving, e.g., to keep the solar array pointed at the sun while in motion. The offset steering combined with active suspension improves driving in soft soil. The rover's on-­board software utilizes NASA's Core Flight Software, which is a reusable flight software environment. During 2015, we completed the initial rover software build, which provides low-­level hardware interfaces, basic mobility control, waypoint driving, odometry, basic error checking, and camera services. Development of the prototype rover has enabled maturation of many of the subsystems to TRL 5. During the next year, we will conduct integrated testing of concepts of operation, navigation, and remote driving tools. In addition, we will perform environmental tests including radiation (avionics), thermal and thermal/vacuum (mechanisms), and gravity offload (mobility).

robotics↗
NASA NTRS2010

TPSAS-NF1676L-10751-DND

Developed in the late 1960's, the NASA Langley Research Center's 14-by-22-Foot Subsonic Tunnel was not originally conceived to test and evaluate the aeroacoustic characteristics of flight vehicles. However, sometime after the tunnel's inception, a need to do so developed. To facilitate acoustic measurements, a removable microphone traverse was designed and built. The implemented solution was functional yet time consuming to install and remove. Comprised of numerous interlocking parts, each installation of the system required three weeks of non-productive tunnel time, numerous personnel, and specialized equipment. A recently renewed focus on aeroacoustic testing brought about a desire to improve the operational efficiency of this type of testing in the 14-by 22-Foot Subsonic Tunnel. Specifically, a goal was established to reduce non-productive installation time from three weeks to just three shifts. In addition, no specialized equipment was to be required for installation and removal. Meeting these goals required the development of a new microphone traverse system. This presentation will provide details of the newly designed, built and commissioned traverse which meets the stated objectives.

Low speed wind tunnel↗
NASA NTRS2019

Observations of Surface Mass Balance on Pine Island Glacier, West Antarctica, and the Effect of Strain History in Fast-Flowing Sections

Surface mass balance (SMB) is the net input of mass on a glacier's upper surface, composed of snow deposition, melt and erosion processes, and is a major contributor to the overall mass balance. Pine Island Glacier (PIG) in West Antarctica has been dynamically imbalanced since the early 1990s, indicating that discharge of solid ice into the oceans exceeds snow deposition. However, observations of the SMB pattern on the fast flowing regions are scarce, and are potentially affected by the firn's strain history. Here, we present new observations from radar-derived stratigraphy and a relatively dense network of firn cores, collected along a ~900 km traverse of PIG. Between 1986 and 2014, the SMB along the traverse was 0.505 m w.e. a−1 on average with a gradient of higher snow deposition in the South-West compared with the North-East of the catchment. We show that along ~80% of the traverse the strain history amounts to a misestimation of SMB below the nominal uncertainty, but can exceed it by a factor 5 in places, making it a significant correction to the SMB estimate locally. We find that the strain correction changes the basin-wide SMB by ~0.7 Gt a−1 and thus forms a negligible (1%) correction to the glacier's total SMB.

ice core↗
NASA NTRS2020

Comparisons of Satellite and Airborne Altimetry with Ground-Based Data from the Interior of the Antarctic Ice Sheet

A series of traverses has been conducted for validation of the NASA Ice, Cloud, and land Elevation Satellite 2 on the flat interior of the Antarctic ice sheet. GNSS data collected on three separate 88S Traverses intersect 20% of the ICESat-2 reference ground tracks and have precisions of better than ±7 cm and biases of less than ~4 cm. Data from these traverses were used to assess heights from ICESat-2, CryoSat-2, and Airborne Topographic Mapper (ATM). ICESat-2 heights have better than ±3.3 cm bias and better than ±7.2 cm precision. ATM heights have better than 9.3 cm bias and better than ±9.6 cm precision. CryoSat-2 heights have -38.9 cm of bias and ± 47.3 cm precision. These best-case results are from the flat ice-sheet interior but provide a characterization of the quality of satellite and airborne altimetry.

K. M. Brunt↗
NASA NTRS2021

Framework for Coordinated Efforts in the Exploration of Volatiles in the South Polar Region of the Moon

The exploration of the lunar south polar region and the ground truthing of polar volatiles is one of the top priorities for several space agencies and private partners. Here we use Moon Mineralogy Mapper surficial water ice detections to investigate the location of water ice-bearing permanently shaded regions near the south pole. We extract a variety of parameters such as their temperature regime, slope, hydrogen content, number of ice detections, depth stability for water ice and dry ice, and mobility aspects. We identify 169 water ice-bearing PSRs and use their characteristics to identify sites that allow to access the highest abundances of volatiles, sites that can be visited to characterize the lateral or vertical distribution of volatiles (water ice and dry ice), and sites that allow for the fastest recovery of a scientifically interesting sample. Collectively, 37 PSRs are identified as sites of interest, including 11 that would address more than one mission objective and may be, for that reason, higher priority targets of exploration. These PSRs are found in Shoemaker, Faustini, Cabeus, Malapert, Nobile, Sverdrup, Wiechert J and Haworth craters, as well as 3 unnamed craters (PSRs 57, 120, 89). These sites are all located within 6 degrees of the south pole. We present case studies for a relatively short traverse mission (20 to 50 km) to PSR 89, a medium length traverse (~100 km) to Sverdrup 1, and a longer traverse (~300 km) to Cabeus that can serve as a guide in planning upcoming exploration missions.

Myriam Lemelin↗
NASA NTRS2020

A Reinforcement Learning Framework for Space Missions in Unknown Environments

A land-and-traverse mission to icy worlds such as Europa and Enceladus is challenging due to lack of prior knowledge regarding the terrain conditions. Previous work [1] showed that rovers with high degrees of freedom (DoF) can achieve robust traversal by leveraging redundant modes for mobility to counter terrain uncertainty (e.g. walking, driving, or inch-worming). This paper presents a generic and scalable reinforcement learning scheme for enabling on-board decision making on rovers to automatically switch between modes of traversal based on online performance feedback. The objective is to maximize energy efficiency, minimize operator input and successfully negotiate unstructured terrain conditions without relying on exhaustive prior knowledge. The proposed methodology is well grounded in the literature on reinforcement learning and has been adapted to address conformance to validation and verification requirements and JPL flight operations history of using per-sol prescribed sequences for a space mission.

Tavallali, Peyman↗
NASA NTRS2021

Machine Learning Based Path Planning for Improved Rover Navigation

Enhanced AutoNav (ENav), the baseline surface navigation software for NASA’s Perseverance rover, sorts a list of candidate paths for the rover to traverse, then uses the Approximate Clearance Evaluation (ACE) algorithm to evaluate whether the most highly ranked paths are safe. ACE is crucial for maintaining the safety of the rover, but is computationally expensive. If the most promising candidates in the list of paths are all found to be infeasible, ENav must continue to search the list and run time-consuming ACE evaluations until a feasible path is found. In this paper, we present two heuristics that, given a terrain heightmap around the rover, produce cost estimates that more effectively rank the candidate paths before ACE evaluation. The first heuristic uses Sobel operators and convolution to incorporate the cost of traversing high-gradient terrain. The second heuristic uses a machine learning (ML) model to predict areas that will be deemed untraversable by ACE. We used physics simulations to collect training data for the ML model and to run Monte Carlo trials to quantify navigation performance across a variety of terrains with various slopes and rock distributions. Compared to ENav's baseline performance, integrating the heuristics can lead to a significant reduction in ACE evaluations and average computation time per planning cycle, increase path efficiency, and maintain or improve the rate of successful traverses. This strategy of targeting specific bottlenecks with ML while maintaining the original ACE safety checks provides an example of how ML can be infused into planetary science missions and other safety-critical software.

Yue, Yisong↗
NASA NTRS2023

Developing a Hybrid Space Suit Simulator as a Research Tool for Assessing Extravehicular Activity Relevant Workload

Suited testing time is limited and hard to come by, expensive, and requires a whole team to operate and monitor the suit; however, pressurized spacesuits are not always necessary for initial developmental efforts or assessment of informatics. The Human Physiology, Performance, Protection & Operations Laboratory (H-3PO) at NASA Johnson Space Center (JSC) is developing a Hybrid Space Suit Simulator (HS3) to support characterization of human performance during planetary surface exploration analogs. The primary goal of HS3 is to create a low cost, modular, and unpressurized suit simulator for use as a research tool which provides relevant physical and cognitive workload approximations with EVA-like immersion during planetary extravehicular activity (EVA) simulations. HS3 consists of a soft suit, communication, thermal control, gloves, boots, helmet, and integrated bioinformatics/sensors. The modular design of HS3 allows it to be modified to support test objectives as needed. HS3 enables H-3PO and NASA to complete critical human health and performance testing to address open risks and knowledge gaps in a timely, repeatable, and controlled manner. Four engineering runs were completed with HS3 as a baseline for capability. General workload was assessed while traversing on a passive treadmill and conducting geology tasks. Liquid cooling temperature, suit temperature, and metabolic rates were collected during one extended three-hour engineering run. For the duration of the engineering run the suit temperature was 26.6 ± 1.58 °C while suit humidity was 53.7 ± 5.11 %. Helmet temperature was higher than suit temperature at 27.8 ± 1.58 °C. Helmet humidity was lower than average suit humidity at 50.12 ± 11.3 °C. The liquid cooling temperature remained stable at 22.4 ± 1.62 °C. Resting metabolic rate was 597 ± 88 BTU/hr while metabolic rate increased during traverse tasks at 1500 ± 319 BTU/hr and geology tasks at 921 ± 129 BTU/hr. Following the engineering runs, a characterization study will be conducted. The subjects will perform EVA-like scenarios in both a shirtsleeve only and donned HS3, consisting of EVA task circuit focused on traversing, geological rock sampling, and task board manipulation. The characterization study will provide data capability for implementing HS3 in analog EVA testing environments.

Monica Hew↗
NASA NTRS2024

Core Body Temperature Predictions Using Metabolic Energy Expenditure and Heart Rate During Simulated Extravehicular Activity

Long duration spaceflight missions will require crew to become more autonomous in conducting extravehicular activities (EVA) without direct communication with Mission Control for biomedical support. To enable such autonomy, we are developing a Crew State and Risk Model (CSRM) as a collection of key physiology domains that drive EVA crew capabilities and workloads. One model component of CSRM is human thermal regulation. In this paper, customized development of a baseline model to predict core body temperature is presented using physiology inputs of heart rate and metabolic rate. The model development dataset included a baseline study where participants (n=6, equal male and female) performed a 5-hour EVA in a two-part session while wearing a hybrid space suit simulator (HS3). The first session included an end-to-end EVA traversing 1500 meters to a geology site and traversing back to a habitat conducting geology, payload relocation, and maintenance operations every 500 meters. The second session included standalone tasks of a 2000-meter traverse followed by geology tasks. Thermal measures of core body temperature, local skin temperature, liquid cooling garment temperature, heart rate, and metabolic rate were collected through the test duration. Multiple regression was used to build a linear equation to predict core body temperature from inputs of heart rate and metabolic rate. Heat storage was calculated via predicted core body temperature plus LCG and skin temperatures. The model was tested against a dataset from a pressurized suited test (n=6, equal male and female) in the NASA Active Response Gravity Offload System (ARGOS) conducting similar end-to-end EVA and standalone tasks. Predicted error of the model against the raw test cases was 0.2±0.15 °C. The baseline prediction of core body temperature using heart rates and metabolic rates allows for simple real-time tracking from data collected in-flight to monitor crew consumables and thermal flight limits during EVA.

Bradley Hoffmann↗
NASA NTRSDate not supplied

Simplifying Analysis of Hierarchical HDF5 and NetCDF4 Files with Xarray-Datatree

NASA’s Earth Observing System Data and Information System (EOSDIS) contains thousands of Earth science datasets from satellites, models, and field campaigns. EOSDIS data are stored in formats that are well supported by the Earth Science community. These formats include the Hierarchical Data Format (HDF), with derivative flavors such as HDF-5 and the Network Common Data Format (NetCDF-4). The HDF specification allows for a directory-like hierarchy within a single file, known as "groups". Observational data and associated metadata within a single file can be distributed amongst multiple internal groups, which can also be nested to multiple levels. Working with datasets that have a group hierarchical structure can be difficult because of the nested structure of groups. Widely used packages, such as xarray, have data models that do not accommodate the hierarchical structure within HDF files, requiring users to traverse the file and open different HDF groups as separate, unrelated objects. Xarray-datatree is a Python package developed to solve the difficulty of traversing HDFs with a hierarchical group structure by creating a tree-like hierarchical data structure in xarray. The tree-like structure allows each group to be accessed once a DataTree object is instantiated. The migration of xarray-datatree into the xarray core library will reduce barriers to accessing Earth science data by eliminating the need to understand and traverse the specific hierarchy of a grouped HDF file.

Eni Awowale↗
NASA NTRS1973

A two color, dual beam backscattering laser Doppler velocimeter

A laser Doppler velocimeter has been developed which uses two of the colors emitted from an argon ion laser for the simultaneous measurement of orthogonal velocities. Designed for use in a 2.13 m by 3.05 m wind tunnel, it is capable of traversing its focal volume across spatially unstable flows at scan speeds of up to 1.15 m/sec. Its optical layout and principles of operation are discussed and the data from a typical traversal of a trailing wing tip vortex are presented.

Grant, G. R.↗