Search NASA⌕ Search

SEARCH · Search NASA

Results for “twist wing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 235 records · Page 13
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Aerodynamic design and analysis of the AST-200 supersonic transport configuration concept

The design and analysis of a supersonic transport configuration was conducted using linear theory methods in conjunction with appropriate constraints. Wing optimization centered on the determination of the required twist and camber and proper integration of the wing and fuselage. Also included in the design are aerodynamic refinements to the baseline wing thickness distribution and nacelle shape. Analysis to the baseline and revised configurations indicated an improvement in lift-to-drag ratio of 0.36 at the Mach 2.7 cruise condition. Validation of the design is planned through supersonic wing tunnel tests.

Walkley, K. B.↗
NASA NTRS1980

A study of wing body blending for an advanced supersonic transport

Increases in supersonic cruise lift drag ratio were sought at Mach numbers 2.2 and 2.7 using wing body planform and thickness blending. Constrained twist and camber optimization was performed in the presence of nacelles. Wing and fuselage thickness distributions were optimized for either minimum volume wave drag or minimum total pressure wave drag. The zero leading edge suction lift drag ratios were determined for three wing planforms. The magnitude of the effect of leading edge suction on attainable lift drag ratio was defined on one planform and estimation of available leading edge suction was made.

Goebel, T. P.↗
NASA NTRS1982

Wind-tunnel wall interference corrections for three-dimensional flows

A procedure for the evaluation of wall interference corrections for three-dimensional aircraft configurations is presented. The Mach number and angle-of-attack corrections are obtained by numerically solving the Laplace equation in a parallelepiped with boundary conditions supplied mainly from experimental pressure measurements. A portion of these measurements and other wind-tunnel data required by the procedure may be replaced by theoretical estimates if not available from experiments. The accuracy of the correction results will then depend on the accuracy of these estimates. The correction procedure is applied to an isolated wing and to a wing-tail configuration in a solid-wall wind tunnel. It is found that neglecting twist and camber corrections for the wing effectively increases the tail angle-of-attack correction. Two different Mach number corrections can be calculated for the wing and tail. However, since only one Mach number correction is allowed for both the wing and the tail, and since the wing surface area is larger than the tail surface area, the final correction tends to be closer to the required wing correction. This is a source of error for the tail results.

Rizk, M. H.↗
NASA NTRS1985

An Attached Flow Design of a Noninterferring Leading Edge Extension to a Thick Delta Wing

An analytical procedure for the determination of the shape of a Leading-Edge Extension (LEE) which satisfies design criteria, including especially noninterference at the wing design point, has been developed for thick delta wings. The LEE device best satisfying all criteria is designed to be mounted on a wing along a dividing stream surface associated with an attached flow design lift coefficient (C L,d ) of greater than zero. This device is intended to improve the aerodynamic performance of transonic aircraft at C L greater than C L,d system emanating from the LEE leading edge. In order to quantify this process a twisted and cambered thick delta wing was chosen for the initial application of this design procedure. Appropriate computer codes representing potential and vortex flows were employed to determine the dividing stream surface at C L,d and an optimized LEE planform shape at C L greater than C L,d , respectively. To aid in the LEE selection, the aerodynamic effectiveness of 36 planforms was investigated at C L greater than C L,d . This study showed that reducing the span of the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, regardless of the shape or area. Furthermore, for a fixed area, constant-chord LEE candidates were relatively more efficient than those with sweep less than the wing. At C L,d , the presence of the LEE planform best satisfying the design criteria was found to have no effect on the wing alone aerodynamic performance.

Leading edge extension↗
NASA NTRS1974

Flutter analysis of swept-wing subsonic aircraft with parameter studies of composite wings

A computer program is presented for the flutter analysis, including the effects of rigid-body roll, pitch, and plunge of swept-wing subsonic aircraft with a flexible fuselage and engines mounted on flexible pylons. The program utilizes a direct flutter solution in which the flutter determinant is derived by using finite differences, and the root locus branches of the determinant are searched for the lowest flutter speed. In addition, a preprocessing subroutine is included which evaluates the variable bending and twisting stiffness properties of the wing by using a laminated, balanced ply, filamentary composite plate theory. The program has been substantiated by comparisons with existing flutter solutions. The program has been applied to parameter studies which examine the effect of filament orientation upon the flutter behavior of wings belonging to the following three classes: wings having different angles of sweep, wings having different mass ratios, and wings having variable skin thicknesses. These studies demonstrated that the program can perform a complete parameter study in one computer run. The program is designed to detect abrupt changes in the lowest flutter speed and mode shape as the parameters are varied.

Housner, J. M.↗
NASA NTRS1992

Natural-Flow Wing

Novel scheme developed to contour three-dimensional upper and lower surfaces of wing independently to take maximum advantage of naturally occurring flow and resultant distribution of pressure over broad mach number and lift range. Scheme contours lower and upper surfaces at given cross section to optimize local slopes of upper surface. Sections sheared vertically to create reflexed lower surface. Creates wing nearly flat with mild cumber and minimal twist. Results in design efficient over wide range of lift conditions. Wings for supersonic flight able to provide improved performance at lower speeds without resorting to heavy, complex, and expensive variable-camber devices. Ramifications for both transportation and military systems.

Wood, Richard M.↗
NASA NTRS1981

In-flight deflection measurement of the HiMAT aeroelastically tailored wing

An electro-optical flight deflection measurement system was developed for NASA for use on the highly maneuverable aircraft technology (HiMAT) remotely piloted research vehicle (RPRV) to provide a means of evaluating the performance of the HiMAT's aeroelastically tailored composite wing and canard. A description of the flight deflection measurement system is presented from a user's viewpoint and includes the general method of operation, system capabilities and limitations, method of installation on the HiMAT vehicle, and calibration of targets. Also included is a general description of the HiMAT RPRV and its design goals. Preliminary flight deflection and bending moment data were obtained at Mach 0.8 and were extrapolated to the Mach 0.9 maneuver design condition for comparison to NASTRAN predictions and ground loads test results. The preliminary flight test results tended to agree with the results obtained from the static ground loads tests, that is, that the NASTRAN model overpredicted the streamwise twist of the composite outer wing panel.

Deangelis, V. M.↗
NASA NTRS1983

The Concorde and aeronautical research

Theoretical and experimental work carried out in various research centers, and particularly at ONERA, which led to the conception and to the main technical solutions included in the design of Concorde: plane form, twist and camber of the wing, lift augmentation by upper surface vortices, kinetic heating, air intakes and jet exhausts, materials, aeroelasticity. The development of research, and the numerous tests carried out for the benefit of the designers since the beginning of the project, are also outlined.

Salmon, M.↗
NASA NTRS1985

An attached flow design of a noninterfering leading edge extension to a thick delta wing

The analytical procedure presented for leading edge extension (LEE) determination, in keeping with such design criteria as noninterference at the wing design point, is applied to thick delta wings. The LEE device thus defined is to be mounted on a wing along a dividing stream surface that is associated with an attached flow design lift coefficient greater than zero. The delta wing in question is of twisted and cambered type. It is demonstrated that span reductions for the candidate LEEs has the most detrimental effect on overall aerodynamic efficiency, irrespective of area or shape.

Ghaffari, F.↗
NASA NTRS2000

Flexible Wing Model for Structural Sizing and Multidisciplinary Design Optimization of a Strut-Braced Wing

This paper describes a structural and aeroelastic model for wing sizing and weight calculation of a strut-braced wing. The wing weight is calculated using a newly developed structural weight analysis module considering the special nature of strut-braced wings. A specially developed aeroelastic model enables one to consider wing flexibility and spanload redistribution during in-flight maneuvers. The structural model uses a hexagonal wing-box featuring skin panels, stringers, and spar caps, whereas the aerodynamics part employs a linearized transonic vortex lattice method. Thus, the wing weight may be calculated from the rigid or flexible wing spanload. The calculations reveal the significant influence of the strut on the bending material weight of the wing. The use of a strut enables one to design a wing with thin airfoils without weight penalty. The strut also influences wing spanload and deformations. Weight savings are not only possible by calculation and iterative resizing of the wing structure according to the actual design loads. Moreover, as an advantage over the cantilever wing, employment of the strut twist moment for further load alleviation leads to increased savings in structural weight.

Gern, Frank H.↗
NASA NTRS2009

Applications of Ko Displacement Theory to the Deformed Shape Predictions of the Doubly-Tapered Ikhana Wing

The Ko displacement theory, formulated for weak nonuniform (slowly changing cross sections) cantilever beams, was applied to the deformed shape analysis of the doubly-tapered wings of the Ikhana unmanned aircraft. The two-line strain-sensing system (along the wingspan) was used for sensing the bending strains needed for the wing-deformed shapes (deflections and cross-sectional twist) analysis. The deflection equation for each strain-sensing line was expressed in terms of the bending strains evaluated at multiple numbers of strain-sensing stations equally spaced along the strain-sensing line. For the preflight shape analysis of the Ikhana wing, the strain data needed for input to the displacement equations for the shape analysis were obtained from the nodal-stress output of the finite-element analysis. The wing deflections and cross-sectional twist angles calculated from the displacement equations were then compared with those computed from the finite-element computer program. The Ko displacement theory formulated for weak nonlinear cantilever beams was found to be highly accurate in the deformed shape predictions of the doubly-tapered Ikhana wing.

Ko, William L.↗
NASA NTRS1929

A Study of Wing Flutter

Part I describes vibration tests, in a wind tunnel, of simple airfoils and of the tail plane of an M0-1 airplane model; it also describes the air flow about this model. From these tests are drawn inferences as to the cause and cure of aerodynamic wing vibrations. Part II derives stability criteria for wing vibrations in pitch and roll, and gives design rules to obviate instability. Part III shows how to design spars to flex equally under a given wing loading and thereby economically minimize the twisting in pitch that permits cumulative flutter. Resonant flutter is not likely to ensue from turbulence of air flow along past wings and tail planes in usual flying conditions. To be flutterproof a wing must be void of reversible autorotation and not have its centroid far aft of its pitching axis, i. e., axis of pitching motion. Danger of flutter is minimized by so proportioning the wing's torsional resisting moment to the air pitching moment at high-speed angles that the torsional flexure is always small. (author)

Zahm, A F↗