Search NASA⌕ Search

SEARCH · Search NASA

Results for “ARC WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Microstructures in a resistance spot welded high strength dual phase steel

The microstructure of a high strength dual phase steel resistance spot welded with tempering-pulse technology is characterized in this paper. In the fusion zone, there is a needle-like microstructure identified as acicular or side plate ferrite that has a cube-on-cube orientation relationship with respect to the surrounding martensite. In contrast to the microstructures produced by the lower cooling rate arc or laser welding techniques, the nucleation of this fine intragranular ferrite takes place independent of inclusions. Further, a leaf-like microstructure within the martensitic matrix is found to contain primitive orthorhombic Cr{sub 3}C{sub 2} and face-centered cubic CrC chromium carbides, rather than Cr{sub 23}C{sub 6} or Cr{sub 7}C{sub 3} as is commonly observed in steel alloys. The formation histories of both the ferrite phase and the chromium carbides are analyzed.

36 MATERIALS SCIENCE↗

Experimental Investigation and Numerical Study on the Elimination of Porosity in Aluminum Alloy Laser Welding and Laser–GMA Welding

Keyhole-induced porosity can strongly weaken the joint strength during aluminum alloy laser welding. Two factors are proposed to be responsible for the porosity formation: bubble formation caused by the instability of the keyhole and bubble captured by the solidification interface. Based on numerical and experimental results, the porosity is suppressed with preheating, due to the capillary stability of the keyhole and easy escape of bubble. N{sub 2} shielding gas has a minor effect on keyhole stability, but it reduces the porosity number as N{sub 2} bubble can dissolve into the liquid aluminum alloy melt pool quickly. The laser–gas metal arc (laser–GMA) welding process can stabilize the metallic plume and enlarge the weld pool. As a result, few spatters and bubbles are formed, and bubbles are easily escaped, both of which contribute to the suppression of porosity.

36 MATERIALS SCIENCE↗

Sigma phase morphologies in cast and aged super duplex stainless steel

Solution annealed and water quenched duplex and super duplex stainless steels are thermodynamically metastable systems at room temperature. These systems do not migrate spontaneously to a thermodynamically stable condition because an energy barrier separates the metastable and stable states. However, any heat input they receive, for example through isothermal treatment or through prolonged exposure to a voltaic arc in the welding process, cause them to reach a condition of stable equilibrium which, for super duplex stainless steels, means precipitation of intermetallic and carbide phases. These phases include the sigma phase, which is easily identified from its morphology, and its influence on the material's impact strength. The purpose of this work was to ascertain how 2-hour isothermal heat treatments at 920 deg. C and 980 deg. C affect the microstructure of ASTM A890/A890M GR 6A super duplex stainless steel. The sigma phase morphologies were found to be influenced by these two aging temperatures, with the material showing a predominantly lacy microstructure when heat treated at 920 deg. C and block-shaped when heat treated at 980 deg. C.

36 MATERIALS SCIENCE↗

Process Modeling for Additive Manufacturing

Additive Manufacturing (AM) provides a new avenue to design innovative materials and components that cannot be created using traditional machining operations. With current AM capabilities, complex designs (such as those required in weapon systems) can be readily manufactured with laser powder forming (or Laser-Engineered Net Shaping (LENSTM)) [1] that would be otherwise cost prohibitive or impossible to produce. However, before an AM product can be qualified for weapon applications, the characteristics of the metals produced by additive manufacturing processes need to be well understood. This work focuses on the development of computational simulation tools to model the metal additive manufacturing process. This work extends and integrates existing Sandia National Laboratories tools to accomplish the following: (i) be able to better predict residual stresses in AM product, (ii) extend high-fidelity material models to capture material evolution during the formation process, leading to prediction of end-state material properties, and (iii) provide a basis for engineering tools to propose improvements to additive manufacturing process variables, including those that minimize process variation. While this work in its current state is directly applicable to additive manufacturing processes, the tools developed may also help enable modeling welding processes such as gas tungsten arc (GTA), electron beam, and laser welding.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Irradiation of Advanced Cladding Specimens in the High Flux Isotope Reactor: Capsule Designs and Test Matrix

The Advanced Fuels Campaign (AFC) has initiated the Advanced Reactor Cladding (ARC) irradiation campaign to generate irradiation performance data for candidate fuel cladding concepts. The campaign includes a diverse set of ferritic/martensitic steels, oxide dispersion strengthened (ODS) alloys, FeCrAlbased alloys, coated materials, and welded cladding specimens produced through multiple US Department of Energy (DOE) programs and international collaborations. Three complementary experimental thrusts comprise the campaign: tensile testing (ARC Tensile) to rapidly screen candidate alloys, fracture toughness testing (ARC Fracture) to evaluate irradiation effects on crack resistance, and tubular weld testing (ARC Weld) to quantify irradiation-induced changes in the mechanical performance of end cap welds. This report documents the irradiation campaign design, including the selected materials, specimen types, irradiation matrix, and capsule designs for irradiation within the High Flux Isotope Reactor (HFIR). A total of 14 irradiation capsules were developed to achieve target irradiation temperatures between 300°C and 600°C and doses up to 30 dpa. Thermal analyses were performed using finite element methods to establish capsule geometries capable of achieving the desired specimen temperatures while accommodating differences in specimen geometry and material properties. The resulting capsule designs provide the basis for irradiation of the AFC-ARC experimental matrix and subsequent post-irradiation examination to assess the effects of neutron irradiation on advanced cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Imaging Enhanced Simulation Validation for Directed Energy Deposition Additive Manufacturing (Final CRADA Report – NFE-22-09107)

Directed Energy Deposition (DED) is a welding-based metal Additive Manufacturing (AM) process that relies on the programmed rastering of an electric arc or laser induced weld pool to construct a component in a layerwise fashion. The induced complex thermal field and uneven thermal contraction depends on the printed geometry and scan pattern, and as such, accumulated residual stresses and distortions are complex and difficult to predict. Several prior works have resulted in tools to combat this issue; ANSYS has developed a thermoplastic simulation package targeting DED AM, and ORNL has developed an in-situ imaging sensor package ‘Stereo Correlated Optical and Pyrometric System’ (SCOPS) that can spatially monitor temperature and full field strain. In this CRADA, these tools are compared in order to validate the results and complimentarily address the weaknesses in each other.

36 MATERIALS SCIENCE↗

Finite Element Analysis and In-Situ Measurement of Out-of-Plane Distortion in Thin Plate TIG Welding

Transient distortion of thin plate in the welding process usually has a complicated mode and large magnitude. Quantitative measurement and prediction of full-field distortion are challenging and rarely reported up to now. In this study, the out-of-plane distortion of a thin plate during the Tungsten Inert Gas (TIG) welding process was measured using the digital image correlation (DIC) method. A simulation model based on thermal elastic–plastic finite element method (FEM) and DIC measured geometric imperfection were developed for accurate prediction of the transient welding distortion. The numerical results and experimental data agreed very well in both out-of-plane deformation modes and magnitudes of the plate at different stages of welding. The maximum out-of-plane distortion was larger than 4 mm during welding which can cause instability of arc length and heat input. The distance change between welding torch and plate surface was investigated under different initial deflections of the plate before welding. The plate with flat geometry shows the minimum transient and final gap change. In addition, the relationship between heat input and welding distortion was clarified through a series of numerical analyses. As a result, optimization of welding heat input can be performed based on numerical results to avoid excessive welding distortion.

36 MATERIALS SCIENCE↗

Digital bead modeling for wire-arc directed energy deposition

Prediction of 2D cross-section and full 3D geometry for stacked weld beads is critical for the outcome of wire-arc directed energy deposition (DED) parts; however, most additive path planning software packages model beads as extrusions of a rectangle. Weld beads are not rectangular, and the resulting shape is dependent upon physics effects at the moment of deposition. Physics phenomena such as the geometry of the underlying surface, the heat input of the welding mode, and the direction of gravity contribute to bead shape. Here, this paper presents a novel implicit modeling method that discretizes a 2D area or 3D volume of space into pixels or voxels and constructs fields based on these physics phenomena. The fields are combined using a weighting scheme trained on 3D scan measurements of welds and wire-arc DED prints. Pixels or voxels are added until the known amount of deposited volume has been achieved. Thereby, a strong conservation of mass principle is applied to the process. Utilizing machine learning techniques, the present model can be trained on a database of scans allowing for the representation of a wide variety of prints. Results show that this method can produce predictions with realistic bead morphology and sub-millimeter form error.

Bead geometry modeling↗

Torch End-Effector and TIG Electrode Changeout Design for a TIG Welding Robot Used in Metal Big Area Additive Manufacturing

Metal Big Area Additive Manufacturing (mBAAM) is a promising approach to large-scale metal additive manufacturing (AM) or 3D printing. The mBAAM system uses an arc-based wire-fed welding robot to build metal parts. A multi-degree-of-freedom robotic arm is known for its extensive range of motion and reliable tool handling. Attaching a torch end-effector to a robotic arm gives it welding capabilities; however, this decreases the motion range and dynamics of the robot. As a result, build volume and printing accuracy are decreased. Additionally, only a portion of time is spent printing in an arc-based process. Maintenance leads to downtime on the system. In a tungsten inert gas (TIG)-based process, the torch electrode wears out over time and must be changed to avoid defective deposition. This paper proposes an approach for a compact torch end-effector to improve the robot’s build volume. This paper also proposes an approach to reducing non-printing process time by designing and implementing a semi-automated electrode changing system.

Masuo, Chris↗

A Fast and Accurate Reduced-Order Model for High-Intensity Transferred Arc Discharges

Arc discharges are widely used in welding, plasma smelting, and other industrial processes, where variations in operating conditions strongly affect arc stability, temperature distribution, and energy transfer. Accurate modeling of these phenomena typically requires computationally expensive high-fidelity simulations. This study presents a hierarchy of three arc discharge models with progressively reduced physical fidelity. The high-fidelity model provides a fully physics-resolved reference, the reduced-order model reproduces the dominant thermal and flow characteristics of the arc with reasonable accuracy, and the Elenbaas-Heller model captures key trends in a simplified, rapid formulation. This hierarchy demonstrates that reduced-order model can effectively balance predictive fidelity and computational efficiency, providing practical tools for arc simulation and parametric studies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Modeling Arcs

Although vacuum arcs were first identified over 110 years ago, they are not yet well understood. We have since developed a model of breakdown and gradient limits that tries to explain, in a self-consistent way: arc triggering, plasma initiation, plasma evolution, surface damage and gradient limits. We use simple PIC codes for modeling plasmas, molecular dynamics for modeling surface breakdown, and surface damage, and mesoscale surface thermodynamics and finite element electrostatic codes for to evaluate surface properties. Since any given experiment seems to have more variables than data points, we have tried to consider a wide variety of arcing (rf structures, e beam welding, laser ablation, etc.) to help constrain the problem, and concentrate on common mechanisms. While the mechanisms can be comparatively simple, modeling can be challenging.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

SS410 Process Development and Characterization

Wire-fed stainless-steel additive manufacturing provides the potential for an alternative to traditional stainless-steel tool making processes. 410 stainless steel provides the necessary hardness for long term tool use and its corrosion resistances negates the need for post processing of non-critical faces. 410 has unique characteristics that require different design and welding parameters from other materials. This paper will look at the parameters and characteristics to expect when using wire-arc deposition for 410 stainless steel. Individual weld beads and simple geometric features were printed using the mBAAM wire-arc system at ORNL to determine effective wire-arc parameters for SS410. Once parameters were chosen, additional features were printed to determine the geometric characteristics of printed SS410 as well as compare the differences between designed geometries and printed geometries. These results allow for the formulation of smarter design rules when designing parts for SS410 additive manufacturing.

Vaughan, Derek↗

Wire-Based Additive Manufacturing of Stainless Steel Components

In this work three different wire-fed additive manufacturing (AM) processes were employed to evaluate differences between laser, arc, and electron beam heat sources used for high-deposition-rate AM on the order of 1 kg/h. Optimum weld and build parameters were developed independently to match the characteristics of each heat source using 308L stainless steel welding wire as the feedstock. Laser-wire AM was made with the lowest energy per unit length of weld and had the best control of the melt pool and surface finish. Wire arc-based AM had an intermediate energy per unit length of weld of approximately 5× that of the laser process, while electron beam wire AM had the highest energy per unit length of weld at approximately 10× that of the laser process. Analysis of the parts that were built included evaluation of mechanical properties and microstructures, and these properties are discussed with respect to the difference in input energy and cooling rates. Results show that all three processes build parts with properties that exceed those of annealed 304L wrought stainless steel. However, significant differences exist between the processes, and the results presented here can be used to help select the best wire-fed process for a given high-deposition-rate application.

36 MATERIALS SCIENCE↗

Sr{sub 7}Ge{sub 6}, Ba{sub 7}Ge{sub 6} and Ba{sub 3}Sn{sub 2} -Three new binary compounds containing dumbbells and four-membered chains of tetrel atoms with considerable Ge-Ge {pi}-bonding character

The germanides Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} as well as the stannide Ba{sub 3}Sn{sub 2} were prepared by arc melting and annealing in welded tantalum ampoules using induction as well as resistance furnaces. The compounds were investigated by powder and single crystal X-ray diffraction. Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} crystallize in the Ca{sub 7}Sn{sub 6} structure type (space group Pmna, Z=4: a=7.777(2) A, b=23.595(4) A, c=8.563(2) A, wR{sub 2}=0.081 (all data), 2175 independent reflections, 64 variable parameters for Sr{sub 7}Ge{sub 6} and a=8.0853(6) A, b=24.545(2) A, c=8.9782(8) A, wR{sub 2}=0.085 (all data), 2307 independent reflections, 64 variable parameters for Ba{sub 7}Ge{sub 6}). Ba{sub 3}Sn{sub 2} crystallizes in an own structure type with the space group P4{sub 3}2{sub 1}2, Z=4, a=6.6854(2) A, c=17.842(2) A, wR{sub 2}=0.037 (all data), 1163 independent reflections, 25 variable parameters. In Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} the Ge atoms are arranged as Ge{sub 2} dumbbells and Ge{sub 4} four-membered atom chains. Their crystal structures cannot be rationalized according to the (8-N) rule. In contrast, Ba{sub 3}Sn{sub 2} presents Sn{sub 2} dumbbells as a main structural motif and thereby can be described as an electron precise Zintl phase. The chemical bonding situation in these structures is discussed on the basis of partial and total Density Of States (DOS) curves, band structures including fatbands, topological analysis of the Electron Localization Function (ELF) as well as Bader analysis of the bond critical points using the programs TB-LMTO-ASA and WIEN2K. While Ba{sub 3}Sn{sub 2} reveals semiconducting behaviour, all germanides Ae{sub 7}Ge{sub 6} (Ae=Ca, Sr, and Ba) show metallic properties and a considerable {pi}-bonding character between the Ge atoms of the four-membered chains and the dumbbells. The {pi}-bonding character of the germanides is best reflected by the resonance hybrid structures {l_brace}[Ge-Ge]{sup 6-}/[Ge-{sup ....}Ge-{sup ....}Ge-{sup ....}Ge]{sup 8-}{r_brace}{r_reversible}{l_brace}[Ge=Ge]{sup 4-}/[Ge-Ge-Ge-Ge]{sup 10-}{r_brace}. - Graphical abstract: The structure of Ba{sub 3}Sn{sub 2} contains Sn{sub 2} dumbbells as a main structural motif and thereby can be described as an electron precise Zintl phase. Ge{sub 2} dumbbells and Ge{sub 4} four-membered atom chains are the predominant features in Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6}. Their crystal structures cannot be rationalized according to the (8-N) rule. While Ba{sub 3}Sn{sub 2} reveals semiconducting behaviour, the germanides Ae{sub 7}Ge{sub 6} (Ae=Ca, Sr, and Ba) show metallic properties and a considerable {pi}-bonding character between the Ge atoms of the four-membered chains and the dumbbells. Highlights: Black-Right-Pointing-Pointer The germanides Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} as well as the stannide Ba{sub 3}Sn{sub 2} have been synthesized. Black-Right-Pointing-Pointer In Sr{sub 7}Ge{sub 6} and Ba{sub 7}Ge{sub 6} the Ge atoms are arranged as dumbbells and four-membered atom chains. Black-Right-Pointing-Pointer Ba{sub 3}Sn{sub 2} presents Sn{sub 2} dumbbells as a main structural motif. Black-Right-Pointing-Pointer The chemical bonding situation within these structures is discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

PDC IC Weld Failure Evaluation and Resolution

During final preparations for start of the PDCF Inner Can (IC) qualification effort, welding was performed on an automated weld system known as the PICN. During the initial weld, using a pedigree canister and plug, a weld defect was observed. The defect resulted in a hole in the sidewall of the canister, and it was observed that the plug sidewall had not been consumed. This was a new type of failure not seen during development and production of legacy Bagless Transfer Cans (FB-Line/Hanford). Therefore, a team was assembled to determine the root cause and to determine if the process could be improved. After several brain storming sessions (MS and T, R and D Engineering, PDC Project), an evaluation matrix was established to direct this effort. The matrix identified numerous activities that could be taken and then prioritized those activities. This effort was limited by both time and resources (the number of canisters and plugs available for testing was limited). A discovery process was initiated to evaluate the Vendor's IC fabrication process relative to legacy processes. There were no significant findings, however, some information regarding forging/anneal processes could not be obtained. Evaluations were conducted to compare mechanical properties of the PDC canisters relative to the legacy canisters. Some differences were identified, but mechanical properties were determined to be consistent with legacy materials. A number of process changes were also evaluated. A heat treatment procedure was established that could reduce the magnetic characteristics to levels similar to the legacy materials. An in-situ arc annealing process was developed that resulted in improved weld characteristics for test articles. Also several tack welds configurations were addressed, it was found that increasing the number of tack welds (and changing the sequence) resulted in decreased can to plug gaps and a more stable weld for test articles. Incorporating all of the process improvements for the actual can welding process, however, did not result in an improved weld geometry. Several possibilities for the lack of positive response exist, some of which are that (1) an insufficient number of test articles were welded under prototypic conditions, (2) the process was not optimized so that significant improvements were observable over the "noise", and (3) the in-situ arc anneal closed the gap down too much so the can was unable to exhaust pressure ahead of the weld. Several operational and mechanical improvements were identified. The weld clamps were changed to a design consistent with those used in the legacy operations. A helium puff operation was eliminated; it is believed that this operation was the cause of the original weld defect. Also, timing of plug mast movement was found to correspond with weld irregularities. The timing of the movement was changed to occur during weld head travel between tacks. In the end a three sequential tack weld process followed by a pulse weld at the same current and travel speed as was used for the legacy processes was suggested for use during the IC qualification effort. Relative to legacy welds, the PDC IC weld demonstrates greater fluctuation in the region of the weld located between tack welds. However, canister weld response (canister to canister) is consistent and with the aid of the optical mapping system (for targeting the cut position) is considered adequate. DR measurements and METs show the PDC IC welds to have sufficient ligament length to ensure adequate canister pressure/impact capacity and to ensure adequate stub function. The PDC welding process has not been optimized as a result of this effort. Differences remain between the legacy BTC welds and the PDC IC weld, but these differences are not sufficient to prevent resumption of the current PDC IC qualification effort. During the PDC IC qualification effort, a total of 17 cans will be welded and a variety of tests/inspections will be performed. The extensive data collected during that qualification effort should be of a sufficient population to determine if additional weld process optimization is necessary prior to production release.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Creep and Creep-Fatigue of Alloy 617 Weldments

Alloy 617 is the primary candidate material for the heat exchanger of a very high temperature gas cooled reactor intended to operate up to 950°C. While this alloy is currently qualified in the ASME Boiler and Pressure Vessel Code for non-nuclear construction, it is not currently allowed for use in nuclear designs. A draft Code Case to qualify Alloy 617 for nuclear pressure boundary applications was submitted in 1992, but was withdrawn prior to approval. Prior to withdrawal of the draft, comments were received indicating that there was insufficient knowledge of the creep and creep-fatigue behavior of Alloy 617 welds. In this report the results of recent experiments and analysis of the creep-rupture behavior of Alloy 617 welds prepared using the gas tungsten arc process with Alloy 617 filler wire. Low cycle fatigue and creep-fatigue properties of weldments are also discussed. The experiments cover a range of temperatures from 750 to 1000°C to support development of a new Code Case to qualify the material for elevated temperature nuclear design. Properties of the welded material are compared to results of extensive characterization of solution annealed plate base metal.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

ADDITIVE MANUFACTURING AND REGULATORY TESTING OF CANISTERS FOR SPENT NUCLEAR FUEL MANAGEMENT

The back end of the fuel cycle focuses on the interim storage, transportation, and final disposition of the spent nuclear fuel from nuclear reactors. Commercial light water nuclear power stations across the United States operate with fuel assemblies being irradiated for up to 6 years (planned) in the reactor pressure vessel. After their planned irradiation, the fuel assemblies are moved to a spent fuel pool within the facility complex. After the spent nuclear fuel is removed from the fuel pool, it is typically inserted into a welded metal canister that can be transferred between overpacks for storage, transportation and possibly disposal. Most dry storage systems being used by industry today use dual purpose canisters (DPCs), designed for use in storage and transportation overpacks, but not specifically designed for disposal. Triple purpose-canisters, designed for disposal in addition to storage and transportation, have also been researched. Traditional manufacturing methods for spent fuel canisters involve fusion welding along the length or circumference of the canister which results in high tensile residual stresses in the joint weld zone (WZ) and heat affected zone (HAZ). In this paper, spent fuel canister designs were printed by wire arc additive manufacturing (AM) using the 316L SS welding wire to demonstrate: 1. Feasibility of spent nuclear fuel canister fabrication using this advanced manufacturing method, 2. Dynamic response of the additive manufacture canister design when subjected to the federally mandated Normal Conditions of Transport (NCT) and Hypothetical Accident Conditions (HAC) physical tests for Type B packages. This paper will focus on the canister printing design and structural tests. The AM 3D printed design, regulatory testing, and post-test evaluation of the canister tested to the 10 CFR 71.71 and 10 CFR 71.73 requirements will be presented. One AM canister design was subjected to the penetration, free drop, and puncture test. Before and after the dynamic structural tests, the AM canister design was scanned with a handheld scanner to capture a 3D CAD geometry to compare to the 3D printed canister design in the deformed shape. The scanned geometry was sectioned in areas with deformation and the cross-section profile was measured to determine accurate and repeated results of the deformed shape of the AM canister design.

Martinez, Oscar↗

Prediction of residual stresses in a multipass pipe weld by a novel 3D finite element approach

Due to enormous computation cost, current residual stress simulation of multipass girth welds are mostly performed using two-dimensional (2D) axisymmetric models. The 2D model can only provide limited estimation on the residual stresses by assuming its axisymmetric distribution. In this study, a highly efficient thermal-mechanical finite element code for three-dimensional (3D) model has been developed based on high performance Graphics Processing Unit (GPU) computers. Our code is further accelerated by considering the unique physics associated with welding processes that are characterized by steep temperature gradient and a moving arc heat source. It is capable of modeling large-scale welding problems that cannot be easily handled by the existing commercial simulation tools. To demonstrate the accuracy and efficiency, our code was compared with a commercial software by simulating a 3D multi-pass girth weld model with over 1 million elements. Our code achieved comparable solution accuracy with respect to the commercial one but with over 100 times saving on computational cost. Moreover, the three-dimensional analysis demonstrated more realistic stress distribution that is not axisymmetric in hoop direction.

Huang, Hui↗