SEARCH · Search NASA

Results for “Airloads”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Viscous/inviscid interaction procedure for high-amplitude oscillating airfoils

A coupling procedure between an inviscid potential theoretical panel method and an unsteady interactive boundary layer calculation procedure has been developed for calculating unsteady airloads on oscillating airfoils in the high-incidence regime. A coordinate transformation into a time-dependent surface coordinate has been incorporated into the boundary layer code to avoid a quasi-steady treatment of the viscous flow equations in the leading edge region. The upper and lower sides of the airfoil are calculated with the complete set of unsteady equations. The interactive region of the boundary layer calculation can be straightforwardly extended over the complete upper surface of the airfoil while accounting for interaction areas in the region of strong adverse pressure gradients with incipient separation. Comparisons of sample calculations with experimental data show reasonably good agreement even for unsteady drag coefficients.

Geissler, W.↗

NASA NTRS1988

Viscous effects on the resonance of a slotted wind tunnel using finite elements

Prompted by the fact that wind tunnel flutter and oscillatory airload measurements are affected by acoustic vibration mode coupling when the model frequency lies near a wind tunnel resonance frequency, a numerical method has been developed for design sensitivity analysis. Solid curves represent the resonant frequency for the slot, without considering the slot's viscosity. While the viscosity effect decreases with increasing slot width, the viscosity effect also decreases as the slot width approaches zero.

Lee, IN↗

NASA NTRS1989

Impact of flow unsteadiness on maneuvers and loads of agile aircraft

A program of airload measurements on a family of low-aspect-ratio delta wings with sharp leading edges, subjected to large amplitude pitch transients with angles of attack up to 90 deg, is reviewed. Even for small values of the pitch-rate parameter, representative of maneuvers anticipated for agile aircraft, the force and moment overshoots can exceed by 50 percent their steady-state values. This is explained in terms of the hysteretic behavior of the breakdown locations of leading-edge vortices. An approximate theoretical model is proposed which includes the breakdown hysteresis as part of a three-term representation of the unsteady chordwise load distribution.

Jarrah, M. Ameen↗

NASA NTRS1989

Lifting-surface theory for propfan vortices impinging on a downstream wing

Retrofitment of commercial aircraft with propfans could introduce undesirable aerodynamic sources of structure-borne noise that are absent for current turbojet powerplants. This paper theoretically examines the whipping action of the vortex wake from a generic propeller on the downstream rigid wing that supports it. The model addresses the high-frequency/compressible regime of most anticipated propfan implementations and produces an analytic solution for the distributed wing airload due to the periodic vortex impingement. The analysis also yields an expression for the local unsteady lift obtained from integration over an arbitrary internal patch of wing surface, for the purpose of applying a practical number of such forces at the nodes of a finite-element model for the corresponding structure (wing response results are not included in the present paper). Reported estimates of induced wing loads for a conventional-propeller example of demonstration appear to be in the reasonable range of expectation.

Martinez, R.↗

NASA NTRS1987

Static aeroelastic analysis for generic configuration aircraft

A static aeroelastic analysis capability that can calculate flexible air loads for generic configuration aircraft was developed. It was made possible by integrating a finite element structural analysis code (MSC/NASTRAN) and a panel code of aerodynamic analysis based on linear potential flow theory. The framework already built in MSC/NASTRAN was used and the aerodynamic influence coefficient matrix is computed externally and inserted in the NASTRAN by means of a DMAP program. It was shown that deformation and flexible airloads of an oblique wing aircraft can be calculated reliably by this code both in subsonic and supersonic speeds. Preliminary results indicating importance of flexibility in calculating air loads for this type of aircraft are presented.

Lee, IN↗

NASA NTRS1989

A survey of nonuniform inflow models for rotorcraft flight dynamics and control applications

The results of a brief survey of nonuniform inflow models was summarized for the calculation of induced velocities at and near a lifting rotor in and out of ground effect. The survey, conducted from the perspective of flight dynamics and control applications, covers a spectrum of flight conditions including hover, vertical flight, and low-speed and high-speed forward flight, and reviews both static and dynamic aspects of the inflow. A primary emphasis is on the evaluation of various simple first harmonic inflow models developed over the years, in comparison with more sophisticated methods developed for use in performance and airload computations. The results of correlation with several sets of test data obtained at the rotor out of ground effect indicate that the Pitt/Peters first harmonic inflow model works well overall. For inflow near the rotor or in ground effect, it is suggested that charts similar to those of Heyson/Katzoff and Castles/De Leeuw of NACA be produced using modern free-wake methods for use in flight dynamic analyses and simulations.

Chen, Robert T. N.↗

NASA NTRS1990

Identification of aerodynamic models for maneuvering aircraft

Due to the requirement of increased performance and maneuverability, the flight envelope of a modern fighter is frequently extended to the high angle-of-attack regime. Vehicles maneuvering in this regime are subjected to nonlinear aerodynamic loads. The nonlinearities are due mainly to three-dimensional separated flow and concentrated vortex flow that occur at large angles of attack. Accurate prediction of these nonlinear airloads is of great importance in the analysis of a vehicle's flight motion and in the design of its flight control system. A satisfactory evaluation of the performance envelope of the aircraft may require a large number of coupled computations, one for each change in initial conditions. To avoid the disadvantage of solving the coupled flow-field equations and aircraft's motion equations, an alternate approach is to use a mathematical modeling to describe the steady and unsteady aerodynamics for the aircraft equations of motion. Aerodynamic forces and moments acting on a rapidly maneuvering aircraft are, in general, nonlinear functions of motion variables, their time rate of change, and the history of maneuvering. A numerical method was developed to analyze the nonlinear and time-dependent aerodynamic response to establish the generalized indicial function in terms of motion variables and their time rates of change.

Chin, Suei↗

NASA NTRS1989

The prediction of loads on the Boeing Helicopters Model 360 rotor

Results are presented from a test/theory correlation investigation involving three rotor-analysis codes, two full potential rotor flow CFD solvers, and data obtained from tests on the Model 360 helicopter's rotor. Attention is given to the problem of reliable higher harmonic loading prediction. It is found that the rotor hover performance and loading experimental data are in excellent agreement with a novel, full potential free-wake computational technology; the need for a multiple tip-vortex wake model's use in predicting vibratory airloads is confirmed.

Dadone, Leo↗

NASA NTRS1990

A survey of nonuniform inflow models for rotorcraft flight dynamics and control applications

The results of a brief survey of nonuniform inflow models was summarized for the calculation of induced velocities at and near a lifting rotor in and out of ground effect. The survey, conducted from the perspective of flight dynamics and control applications, covers a spectrum of flight conditions including hover, vertical flight, and flow-speed and high-speed forward flight, and reviews both static and dynamic aspects of the inflow. A primary emphasis is on the evaluation of various simple first harmonic inflow models developed over the years, in comparison with more sophisticated methods developed for use in performance and airload computations. The results of correlation with several sets of test data obtained at the rotor out of ground effect indicate that the Pitt/Peters first harmonic inflow model works well overall. For inflow near the rotor or in ground effect, it is suggested that charts similar to those of Heyson/Katzoff and Castles/De Leeuw of NACA be produced using modern free-wake methods for use in flight dynamic analyses and simulations.

Chen, Robert T. N.↗

NASA NTRS1990

Comparison of NASTRAN analysis with ground vibration results of UH-60A NASA/AEFA test configuration

Preceding program flight tests, a ground vibration test and modal test analysis of a UH-60A Black Hawk helicopter was conducted by Sikorsky Aircraft to complement the UH-60A test plan and NASA/ARMY Modern Technology Rotor Airloads Program. The 'NASA/AEFA' shake test configuration was tested for modal frequencies and shapes and compared with its NASTRAN finite element model counterpart to give correlative results. Based upon previous findings, significant differences in modal data existed and were attributed to assumptions regarding the influence of secondary structure contributions in the preliminary NASTRAN modeling. An analysis of an updated finite element model including several secondary structural additions has confirmed that the inclusion of specific secondary components produces a significant effect on modal frequency and free-response shapes and improves correlations at lower frequencies with shake test data.

Idosor, Florentino↗

NASA NTRS1990

Tabulation of data from the tip aerodynamics and acoustics test

In a continuing effort to understand helicopter rotor tip aerodynamics and acoustics, researchers at Ames Research Center conducted a flight test. The test was performed using the NASA White Cobra and a set of highly instrumented blades. Tabular and graphic summaries of two data subsets from the Tip Aerodynamics and Acoustics Test are given. The data presented are for airloads, blade structural loads, blade vibrations, with summary tables of the aircraft states for each test point. The tabular data consist of the first 15 harmonics only, whereas the plots contain the entire measured frequency content.

Cross, Jeffrey L.↗

NASA NTRS1990

Modal analysis of UH-60A instrumented rotor blades

The dynamic characteristics of instrumented and production UH-60A Black Hawk main rotor blades were measured, and the results were validated with NASTRAN finite element models. The blades tested included pressure and strain-gage instrumented blades, which are part of the NASA Airloads Flight Research Phase of the Modern Technology Rotor Program. The dynamic similarity of the blades was required for accurate data collection in this program. Therefore, a nonrotating blade modal analysis was performed on the first 10 free-free modes to measure blade similarities. The results showed small differences between the modal frequencies of instrumented and production blades and a close correlation with the NASTRAN models. This type of modal testing and analysis is recommended as a standard procedure for future instrumented blade flight testing.

Hamade, Karen S.↗

NASA NTRS1990

A novel potential/viscous flow coupling technique for computing helicopter flow fields

Because of the complexity of helicopter flow field, a zonal method of analysis of computational aerodynamics is required. Here, a new procedure for coupling potential and viscous flow is proposed. An overlapping, velocity coupling technique is to be developed with the unique feature that the potential flow surface singularity strengths are obtained directly from the Navier-Stokes at a smoother inner fluid boundary. The closed-loop iteration method proceeds until the velocity field is converged. This coupling should provide the means of more accurate viscous computations of the near-body and rotor flow fields with resultant improved analysis of such important performance parameters as helicopter fuselage drag and rotor airloads.

Summa, J. Michael↗

NASA NTRS1991

Unified aeroacoustics analysis for high speed turboprop aerodynamics and noise. Volume 3: Application of theory for blade loading, wakes, noise, and wing shielding

Results of the program for the generation of a computer prediction code for noise of advanced single rotation, turboprops (prop-fans) such as the SR3 model are presented. The code is based on a linearized theory developed at Hamilton Standard in which aerodynamics and acoustics are treated as a unified process. Both steady and unsteady blade loading are treated. Capabilities include prediction of steady airload distributions and associated aerodynamic performance, unsteady blade pressure response to gust interaction or blade vibration, noise fields associated with thickness and steady and unsteady loading, and wake velocity fields associated with steady loading. The code was developed on the Hamilton Standard IBM computer and has now been installed on the Cray XMP at NASA-Lewis. The work had its genesis in the frequency domain acoustic theory developed at Hamilton Standard in the late 1970s. It was found that the method used for near field noise predictions could be adapted as a lifting surface theory for aerodynamic work via the pressure potential technique that was used for both wings and ducted turbomachinery. In the first realization of the theory for propellers, the blade loading was represented in a quasi-vortex lattice form. This was upgraded to true lifting surface loading. Originally, it was believed that a purely linear approach for both aerodynamics and noise would be adequate. However, two sources of nonlinearity in the steady aerodynamics became apparent and were found to be a significant factor at takeoff conditions. The first is related to the fact that the steady axial induced velocity may be of the same order of magnitude as the flight speed and the second is the formation of leading edge vortices which increases lift and redistribute loading. Discovery and properties of prop-fan leading edge vortices were reported in two papers. The Unified AeroAcoustic Program (UAAP) capabilites are demonstrated and the theory verified by comparison with the predictions with data from tests at NASA-Lewis. Steady aerodyanmic performance, unsteady blade loading, wakes, noise, and wing and boundary layer shielding are examined.

Hanson, D. B.↗

NASA NTRS1991

Applications of higher harmonic control to hingeless rotor systems

A comprehensive analytical formulation was developed to predict the vibratory hub loads of a helicopter rotor system in forward flight. This analysis is used to calculate the optimal higher harmonic control inputs and associated actuator power required to minimize these hub loads. The present formulation is based on a finite element method in space and time. A nonlinear time domain, unsteady aerodynamic model is used to obtain the airloads, and the rotor induced inflow is calculated using a nonuniform inflow model. Predicted vibratory hub loads are correlated with experimental data from a scale model rotor. Results of a parametric study on a hindgeless rotor show that blade flap, lag and torsion vibration characteristics, offset of blade center of mass from elastic axis, offset of elastic axis from quarter-chord axis, and blade thrust greatly affect the higher harmonic control actuator power requirement.

Nguyen, Khanh↗

NASA NTRS1990

Estimation of UH-60 blade aerodynamic loads and rotor impedance using generalized strain pattern/Kalman filter approach

The purpose of the study is to develop and verify a methodology capable of predicting the vibration levels and estimating the aerodynamic loads and rotor impedance of a rotorcraft blade. Simulated flight test data is generated, blade airloads and elastic hub motions are estimated from the simulated data through the use of the Kalman filter/smoother, simulation upgrading and parameter identification are performed, and the ability to identify rotor impedance from a simulation by isolating the rotor model and providing a prescribed motion for the hub as rotor excitation is demonstrated. It is pointed out that the statistical estimation procedure utilized in the proposed methodology minimizes the impact of sensor noise, truncation error, and instrumentation bias on the results.

Bruhis, Ofer↗

NASA NTRS1991

Navier-Stokes computations with finite-rate chemistry for LO2/LH2 rocket engine plume flow studies

Computational fluid dynamics methods have been developed and applied to Space Shuttle Main Engine LO2/LH2 plume flow simulation/analysis of airloading and convective base heating effects on the vehicle at high flight velocities and altitudes. New methods are described which were applied to the simulation of a Return-to-Launch-Site abort where the vehicle would fly briefly at negative angles of attack into its own plume. A simplified two-perfect-gases-mixing approach is used where one gas is the plume and the other is air at 180-deg and 135-deg flight angle of attack. Related research has resulted in real gas multiple-plume interaction methods with finite-rate chemistry described herein which are applied to the same high-altitude-flight conditions of 0 deg angle of attack. Continuing research plans are to study Orbiter wake/plume flows at several Mach numbers and altitudes during ascent and then to merge this model with the Shuttle 'nose-to-tail' aerodynamic and SRB plume models for an overall 'nose-to-plume' capability. These new methods are also applicable to future launch vehicles using clustered-engine LO2/LH2 propulsion.

Dougherty, N. Sam↗

NASA NTRS1991

Numerical prediction of the unsteady flowfield around the F-18 aircraft at large incidence

This paper describes a numerical method capable of solving the steady and unsteady viscous flow around complete aircraft configurations at high angles of attack. This method is used to simulate the external flow around the F-18 aircraft, including deflected control surfaces. The current technique employs a generalized overset zonal grid scheme to decompose the computational space around the aircraft. The grid around various components of the aircraft are created numerically using a three-dimensional hyperbolic grid generation procedure. The Reynolds-averaged Navier-Stokes equations are integrated using a time-accurate, implicit procedure. Results for the turbulent flow around the F-18 aircraft at 30 degrees angle of attack show the details of the flowfield structure, including the unsteadiness created by the vortex burst and the resulting fluctuating airloads exerted on the vertical tail. The computed results agree fairly well with flight data for surface pressure, surface flow pattern, vortex burst location, and the dominant frequency for tail load fluctuations.

Rizk, Yehia M.↗