Search NASA⌕ Search

SEARCH · Search NASA

Results for “Aqueous corrosion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Achieving Stable Molybdenum Oxide Cathodes for Aqueous Zinc-Ion Batteries in Water-in-Salt Electrolyte

A layered MoO 3 material with large interlayer spacing represents a promising cathode for aqueous rechargeable Zn-ion batteries (ARZIBs), but the implementation of this material is limited due to the intrinsically low conductivity and poor structural stability. A 30 m ZnCl 2 water-in-salt electrolyte (WISE) was introduced to a MoO 3 nanobelt cathode for the first time, significantly increasing the stability of MoO 3 cathodes compared to those in 3 M ZnSO 4 and 3 M ZnCl2 electrolyte. The Zn/MoO 3 cell in WISE unambiguously demonstrated significantly improved rate performance delivering 349, 253, and 222 mAh/g at 100, 500, and 1000 mA/g, denoting a 2×, and 12× capacity increase of those achieved in 3 M electrolytes at 500 and 1000 mA/g, respectively. A capacity retention rate of 73% was achieved after (dis)charging at 100 mA/g for 100 cycles, and no obvious capacity fading was observed at higher current densities of 500 mA/g and 2A/g. A compilation of structural and morphological characterization was systematically performed to provide insight into the mechanisms of the improved performance in ZnCl 2 WISE for the MoO3 cathode materials. Specifically, our data collectively suggested that the drastic fading in 3M electrolytes can be attributed to the parasitic surface deposits on Zn originated from Mo dissolution and H 2 formation due to Zn corrosion and hydrogen evolution reaction (HER), which were significantly suppressed in the ZnCl 2 WISE. The direct visualization of these side reactions was achieved for the first time in the Zn-MoO 3 system, using an in situ optoelectrochemical measurement.

25 ENERGY STORAGE↗
NASA NTRS1985

A potentiodynamic study of aluminum-lithium alloys in an aqueous sodium chloride environment

The characteristics of the potentiodynamic curves for Al-Li alloys in 3.5 percent NaCl aqueous solution are explained and the electrochemical parameters of the potentiodynamic technique are correlated to observed pitting and intergranular cracking behavior. It is shown that the oxygen content of the sodium chloride electrolyte plays an important role in the electrochemical behavior of Al-Li alloys. The potentiodynamic behavior of the alloys is found to be insensitive to variation in compositional content and heat treatment, both of which affect the stress-corrosion behavior. Stringer oxide particle attack and random pitting are observed. It is shown that alternate-immersion exposure prior to potentiodynamic polarization may offer a means of assessing susceptibility to stress-corrosion cracking.

Tsao, C.-H. T.↗
NASA NTRS1993

Attenuation of Glass Dissolution in the Presence of Natural Additives

The study described here explored the dissolution kinetics of glasses in aqueous environments in systems which included a variety of natural crystalline solids in addition to the glass itself and the aqueous phase. The results demonstrated the possibility of a dramatic decrease in the rate of dissolution of silicate glass in the presence of certain varieties of olivine-based materials. This decrease in dissolution rate was shown to be due to the fact that these additives consist mostly of Mg-based material but also contain minor amounts of Al and Ca. The combined presence of Mg with these minor species affected the corrosion rate of the glass as a whole, including its most soluble components such as boron. The study has potentially important implications to the durability of glasses exposed to natural environments. The results may be relevant to the use of active backfill materials in burial sites for nuclear waste glasses as well as to better understanding of the environmental degradation of natural and ancient glasses.

Sang, Jing C.↗
NASA NTRS2004

Conversion Coatings for Aluminum Alloys by Chemical Vapor Deposition Mechanisms

With the rise of environmental awareness and the renewed importance of environmentally friendly processes, the United States Environmental Protection Agency has targeted surface pre-treatment processes based on chromates. Indeed, this process has been subject to regulations under the Clean Water Act as well as other environmental initiatives, and there is today a marked movement to phase the process out in the near future. Therefore, there is a clear need for new advances in coating technology that could provide practical options for replacing present industrial practices. Depending on the final application, such coatings might be required to be resistant to corrosion, act as chemically resistant coatings, or both. This research examined a chemical vapor deposition (CVD) mechanism to deposit uniform conversion coatings onto aluminum alloy substrates. Robust protocols based on solutions of aryl phosphate ester and multi-oxide conversion coating (submicron) films were successfully grown onto the aluminum alloy samples. These films were characterized by X-ray Photoelectron Spectroscopy (XPS). Preliminary results indicate the potential of this technology to replace aqueous-based chromate processes.

Reye, John T.↗
DOE OSTI2024

Calcined Polyethyleneimine Coated Optical Fibers for Distributed pH Monitoring at High Pressures and Temperatures

In the oil and gas, CO2 sequestration, H2 subsurface storage, and geothermal energy sectors, subsurface pH measurements are critical for monitoring the geochemical conditions and estimating potential corrosion rates of wellbore systems. Real-time pH measurements in these conditions are vital for detecting and predicting corrosion deterioration of wellbore components that may jeopardize the safety and continued operation of wellbore systems. Building off of earlier TiO2 based pH sensors and the known pH sensitivity of amine-based polymers, a coating based on the secondary amine polymer polyethyleneimine (PEI) was developed. The sensor coating was treated with a high temperature (500 °C) calcination procedure in air to convert it into a more stable oxidized coating capable of withstanding hot aqueous solutions without dissolving while retaining linear pH sensitivity from pH values between 2 and 11. The sensor performance was measured using optical transmission measurements in solutions of various pHs and using optical backscatter reflectometry for distributed pH sensing demonstration in wellbore-relevant pressures (up to 1000 psi) and temperatures (80 °C). A calibration curve with strong differentiation between acidic and alkaline pH was developed for both transmission-based and distributed pH measurements, using fixed wavelength transmission and integrated linear amplitude of backscattered light for distributed measurements.

Shumski, Alexander↗
DOE OSTI2025

Highly textured metal anodes for stable aqueous batteries: Fabrication and characterization

We report a purely mechanical “cold-compression flow” method for fabricating Zn, Sn, and In substrates with tunable crystallographic textures. Using textured Zn as a model system, we investigate Zn electrocrystallization and demonstrate correlated growth of crystalline films with correlation lengths from tens to hundreds of micrometers. At 5 milliamperes per square centimeter (mA/cm 2 ), capacities between 20 and 82 milliampere hours per square centimeter (mA·hour/cm 2 ) are achieved depending on substrate texture level. At higher currents (40 mA/cm 2 ), capacities reach up to 604 mA·hour/cm 2 . Rotating disk electrode studies show that dominantly (002) textured Zn substrates exhibit enhanced corrosion resistance and reduced interphase passivation. We introduce an effective Damköhler number (Da*) to concisely describe morphological evolution during electrocrystallization across substrates with different textures. High-texture (002) Zn substrates substantially enhance performance in high-capacity (~20 mA·hour/cm 2 ) symmetric Zn||Zn cells and full cells (Zn||δ-MnO 2 and Zn||I 2 ), enabling fast-charging and prolonged energy storage in coin and pouch rechargeable Zn battery formats.

Science & Technology - Other Topics↗
DOE OSTI2024

Screening aqueous organic redox couples for spontaneous hydrogen generation on catalysts

Two low-cost redox couples with near neutral or alkaline pH - 7,8-dihydroxyphenazine-2-sulfonic acid (DHPS) and chrome chelated ethylenediaminetetraacetic acid (Cr-EDTA) with ammonia – are identified to generate hydrogen evolution spontaneously on Pt/C catalysts. Cr-EDTA redox couple has two times higher hydrogen evolution rate than that of DHPS, and the charged Cr-EDTA molecules are fully utilized to generate hydrogen gas, while ~ 50% of DHPS molecules are utilized to produce hydrogen spontaneously on Pt/C catalysts. The Cr-EDTA electrolyte enables cost reduction by allowing cheap raw material of Cr and corrosion resistant alloy instead of costly superalloy for catalytic reactor systems. Furthermore, the Cr-EDTA with ammonia as a negolyte for flow batteries was validated to suppress hydrogen evolution side reaction, reach 99% of coulombic efficiency in flow cell operation paired with Fe(CN)6 redox couple near neutral pH.

08 HYDROGEN↗
NASA NTRS1988

Interactions of silicate glasses with aqueous environments under conditions of prolonged contact and flow

This paper discusses mechanisms involving saturation and reactions that lead to the formation of altered phases in silicate glasses considered for use in geologic repositories for nuclear waste. It is shown that the rate of dissolution of silicate glasses exposed to a broad range of contact times, leachant compositions, and surface-to-volume ratios is strongly affected by the presence of reactive species such as Al, Mg, and Fe. The reactive materials may originate in the leachant or, under conditions of high surface-to-volume ratio, in the glass itself. The effects of glass composition on the course of the corrosion process can be viewed in terms of the formation of a surface layer on the leached glass; the type, composition, and structure of this layer control the dissolution behavior of the glass.

Barkatt, Aaron↗
DOE OSTI2024

Calcined Polyethyleneimine-Coated Optical Fibers for Distributed pH Monitoring at High Pressures and Temperatures

In the oil and gas, CO2 sequestration, H2 subsurface storage, and geothermal energy sectors, subsurface pH measurements are critical for monitoring the geochemical conditions and estimating potential corrosion rates of wellbore systems. Real-time pH measurements in these conditions are vital for detecting and predicting corrosion deterioration of wellbore components that may jeopardize the safety and continued operation of wellbore systems. Previous tests using metal oxide-based coatings (TiO2) provided strong responses at elevated temperatures and moderate pressure stability but provided poor differentiation between acidic and alkaline solutions. Building off the pH responsiveness of the TiO2 surface and known pH sensitivity of amine-based polymers, a coating based on the secondary amine polymer polyethyleneimine (PEI) was developed. As the polymer itself is highly water soluble and easily removed by aqueous solutions, the sensor coating was treated with a high temperature (500 °C) calcination procedure in air to convert it into a more stable oxidized coating capable of withstanding hot aqueous solutions without dissolving while retaining linear pH sensitivity from pH values between 2 and 11. The sensor performance was measured using optical transmission measurements in solutions of various pHs and using optical backscatter reflectometry for distributed pH sensing demonstration in wellbore-relevant pressures (up to 1,000 psi) and temperatures (80 °C).

Shumski, Alexander↗
DOE OSTI2025

Performance of a dynamic single bubbler in single and two-phase immiscible liquids

Ensuring nonproliferation and safeguards of special nuclear materials (SNM) is a critical aspect of advancing the nuclear fuel cycle. Traditional bubbler systems used to estimate liquid levels and densities in nuclear recycling processes have limitations, particularly in harsh environments where dip-tube corrosion and buildup necessitate frequent maintenance and recalibration. This study explores the Dynamic Single Bubbler (DSB) method, which utilizes a single dip-tube attached to a linear actuator to estimate liquid properties dynamically. This approach is extended to estimate liquid-liquid interfaces in immiscible liquids and employs a linear regression method to reduce uncertainties and improve accuracy. The DSB method achieved density estimate uncertainties of less than 0.5% and surface level estimate uncertainties typically under 0.5%, across various fluids including water, acetone, methanol, mineral oil, glycerol, and aqueous salt solutions. Results indicate that the DSB method provides accurate and robust estimates of liquid density and surface levels with minimal maintenance and without the need for calibration. Additionally, the method's applicability to immiscible liquids and various dip-tube geometries was demonstrated, showing promise for widespread use in nuclear and other industrial applications.

98 - NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL↗
DOE OSTI2024

Perspective on Lewis Acid‐Base Interactions in Emerging Batteries

Lewis acid-base interactions are common in chemical processes presented in diverse applications, such as synthesis, catalysis, batteries, semiconductors, and solar cells. The Lewis acid-base interactions allow precise tuning of material properties from the molecular level to more aggregated and organized structures. This review will focus on the origin, development, and prospects of applying Lewis acid-base interactions for the materials design and mechanism understanding in the advancement of battery materials and chemistries. The covered topics relate to aqueous batteries, lithium-ion batteries, solid-state batteries, alkali metal-sulfur batteries, and alkali metal-oxygen batteries. In this review, the Lewis acid-base theories will be first introduced. Thereafter the application strategies for Lewis acid-base interactions in solid-state and liquid-based batteries will be introduced from the aspects of liquid electrolyte, solid polymer electrolyte, metal anodes, and high-capacity cathodes. The underlying mechanism is highlighted in regard to ion transport, electrochemical stability, mechanical property, reaction kinetics, dendrite growth, corrosion, and so on. Last but not least, perspectives on the future directions related to Lewis acid-base interactions for next-generation batteries are like to be shared.

Lewis acid-base interactions↗
DOE OSTI2023

Establishing Isotopic Measurement Capabilities using Laser-Induced Breakdown Spectroscopy for the Molten Salt Reactor Campaign

Proof-of-principle H isotope ratios of aqueous aerosol systems and liquid droplets on filter paper have been measured using laser-induced breakdown spectroscopy (LIBS) with root mean square error of prediction values down to 1.9%. Molten salt reactors (MSRs) will consist of a complex chemical and radiological system consistently producing new fission products as the reactor operates. Some of these fission products and/or their daughter species will leave the salt in the reactor off-gas. Monitoring the composition of the off-gas, as well as the salt itself, is important for monitoring reactor performance, including burnup, corrosion, and the concentration of impurities. Tritium is of concern for MSRs because it will be produced from the irradiation of key salt constituents, including Li and Be. LIBS offers an avenue for in situ salt and off-gas monitoring by firing a laser onto or into the sample stream to generate a plasma. The plasma light can be monitored to measure an elemental fingerprint of the sample. Extending this analysis to include isotopic ratios offers a critical expansion of the in situ monitoring capabilities being developed. This study demonstrates the expansion of Oak Ridge National Laboratory’s LIBS capabilities to monitor isotopes and shows how simple calibrations may provide rapid semiquantitative models.

07 ISOTOPE AND RADIATION SOURCES↗
NASA NTRS2002

HAN-Based Monopropellant Technology Development

NASA Glenn Research Center is sponsoring efforts to develop technology for high-performance, high-density, low-freezing point, low-hazards monopropellant systems. The program is focused on a family of monopropellant formulations composed of an aqueous solution of hydroxylammonium nitrate (HAN) and a fuel component. HAN-based monopropellants offer significant mass and volume savings to small (less than 100 kg) satellite for orbit raising and on-orbit propulsion applications. The low-hazards characteristics of HAN-based monopropellants make them attractive for applications where ground processing costs are a significant concern. A 1-lbf thruster has been demonstrated to a 20-kg satellite orbit insertion duty cycle, using a formulation compatible with currently available catalysts. To achieve specific impulse levels above those of hydrazine, catalyst materials that can withstand the high-temperature, corrosive combustion environment of HAN-based monopropellants have to be developed. There also needs to be work done to characterize propellant properties, burning behavior, and material compatibility. NASA is coordinating their monopropellant efforts with those of the United States Air Force.

Reed, Brian↗
DOE OSTI2023

Geochemical Modeling Using OLI Systems Mixed Solvent Electrolyte Model in Support of the Waste Isolation Pilot Plant

Aqueous electrolyte thermodynamic models were developed for synthetic Salado (GWB) and Castile (ERDA-6) brines to inform the experimental design and to facilitate laboratory data interpretation in geochemical studies supporting disposal in the Waste Isolation Pilot Plant (WIPP). The thermodynamic models, which include the relevant vapor-liquid-solid equilibria for the oxidation-reduction conditions of interest, enable computation of system parameters such as activity-based pH, E h [vs. standard hydrogen electrode (SHE)], ionic strength, total dissolved solids, and solution density; the chemical speciation of all phases; saturation tendencies for thermodynamically feasible solids; and changes in brine chemistry because of the addition of H 2 (g), argon, MgO, Fe(0), and other waste form components. The impacts of oxidation-reduction potential (ORP) and pH on aqueous speciation and dominant solid phases were also assessed with the aid of real-solution Pourbaix diagrams for key elements of interest. In addition to the OLI modeling results, limited measurement data for pH and ORP standards are provided, analyzed, and discussed.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Tuning the Solvation Structure in Aqueous Zinc Batteries to Maximize Zn-Ion Intercalation and Optimize Dendrite-Free Zinc Plating

Aqueous zinc batteries are recognized to suffer from H + /Zn 2+ coinsertion in the cathode, but few approaches have been reported to suppress deleterious H + intercalation. We realize this goal by tuning the solvation structure, using LiV 2 (PO 4 ) 3 (LVP) as a model cathode. Phase conversion of LVP induced by H + intercalation is observed in 4 m Zn(OTf) 2 , whereas dominant Zn 2+ insertion is confirmed in a ZnCl 2 water-in-salt electrolyte (WiSE). This disparity is ascribed to the complete absence of free water and a strong Zn 2+ –H 2 O interaction in the latter that interrupts the H 2 O hydrogen bonding network, thus suppressing H + intercalation. On the basis of this strategy, a novel PEG-based hybrid electrolyte is designed to replace the corrosive ZnCl2 WiSE. This system exhibits an optimized Zn 2+ solvation sheath with a similar low free water content, showing not only much better suppression of H + intercalation but also highly reversible Zn plating/stripping with a CE of ~99.7% over 150 cycles.

25 ENERGY STORAGE↗
NASA NTRS1998

Environmentally friendly anti-icing

The present invention describes an aqueous, non-electrolytic, non-toxic, biodegradable, continuous single phase liquid anti-icing or deicing composition for use on the surfaces of, for example, aircraft, airport pavements, roadways, walkways, bridges, entrances, structures, canals, locks, components, vessels, nautical components, railroad switches, and motor vehicles. The anti-icing or deicing composition comprises: (a) water; (b) a non-toxic freezing point depressant selected from the group consisting of monohydric alcohols having from 2 to 6 carbon atoms, polyhydric alcohols having from 3 to 12 carbon atoms, monomethyl or ethyl ethers of polyhydric alcohols having from 3 to 12 atoms or mixtures thereof, wherein the freezing point depressant present is between about 14 to 60 percent by weight; (c) a thickener which is present in between about 0.01 and 10 percent by weight; and (d) optionally a corrosion inhibitor which is present in between about 0.01 and 0.1 percent by weight of the total composition. In one embodiment, the deicing composition further includes (e) a monohydric primary aliphatic unbranched alcohol as a means of forming a thin layer of the composition on the surface of the structure to be given ice protection, and/or as means of forming a homogenized foam with xanthan thickener; which alcohol is selected from the group consisting of alcohols having between 8 to 24 carbon atoms, preferably, 1-dodecanol. Compositions of water, propylene glycol, and/or propanol and xanthan are preferred.

Lockyer, Robert T.↗
DOE OSTI2020

Aqueous passivation of multi-principal element alloy Ni 38 Fe 20 Cr 22 Mn 10 Co 10 : Unexpected high Cr enrichment within the passive film

The aqueous passivation of a non-equiatomic Ni 38 Fe 20 Cr 22 Mn 10 Co 10 - at.% (Ni 40 Fe 20 Cr 20 Mn 10 Co 10 - wt.%) multi-principal element alloy (MPEA) was investigated in 0.1 M NaCl at pH 4 and compared to a conventional binary Ni 76 Cr 24 – at.% (Ni 78 Cr 22 – wt.%) alloy. The electrochemical behavior and oxide film characteristics were explored utilizing in-situ electrochemical and ex-situ surface-sensitive techniques. The passive film composition, thickness, and elemental valence states, as well as, the fate of each element were studied by in-situ atomic emission spectro-electrochemistry, ex-situ X-ray photoelectron spectroscopy, and atom probe tomography. The Ni 38 Fe 20 Cr 22 Mn 10 Co 10 MPEA demonstrated slightly better corrosion resistance compared to the binary Ni 76 Cr 24 , alloy. Passive films on the MPEA contained primarily Cr, and small amounts of Ni, Fe, Co and Mn, while dissolution of Ni, Fe, Co was observed. Ni 0 was enriched at the oxide/metal interface while Cr was depleted. Enrichment of Cr in the passive film occurred to a greater extent in the MPEA than for the Ni-Cr binary alloy. As a result, enrichment factors were determined and the origins of enrichment are discussed.

36 MATERIALS SCIENCE↗