Results for “Axial Force” — Page 14

NASA NTRS2017

Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) Sensor Suite

The Mars 2020 Entry, Descent, and Landing Instrumentation 2 (MEDLI2) sensor suite seeks to address the aerodynamic, aerothermodynamic, and thermal protection system (TPS) performance issues during atmospheric entry, descent, and landing of the Mars 2020 mission. Based on the highly successful instrumentation suite that flew on Mars Science Laboratory (MEDLI), the new sensor suite expands on the types of measurements and also seeks to answer questions not fully addressed by the previous mission. Sensor Package: MEDLI2 consists of 7 pressure transducers, 17 thermal plugs, 2 heat flux sensors, and one radiometer. The sensors are distributed across both the heatshield and backshell, unlike MEDLI (the first sensor suite), which was located solely on the heat-shield. The sensors will measure supersonic pressure on the forebody, a pressure measurement on the aftbody, near-surface and in-depth temperatures in the heatshield and backshell TPS materials, direct total heat flux on the aftbody, and direct radiative heating on the aftbody. Instrument Development: The supersonic pressure transducers, the direct heat flux sensors, and the radiometer all were tested during the development phase. The status of these sensors, including the piezo-resistive pressure sensors, will be presented. The current plans for qualification and calibration for all of the sensors will also be discussed. Post-Flight Data Analysis: Similar to MEDLI, the estimated flight trajectory will be reconstructed from the data. The aerodynamic parameters that will be reconstructed will be the axial force coefficient, freestream Mach number, base pressure, atmospheric density, and winds. The aerothermal quantities that will be determined are the heatshield and backshell aero-heating, turbulence transition across the heatshield, and TPS in-depth performance of PICA. By directly measuring the radiative and total heat fluxes on the back-shell, the convective portion of the heat flux will be estimated. The status of the current tools to perform the post-flight data analysis will be presented, along with plans for model improvements.

Hwang, Helen↗

NASA NTRS2018

Global Ecosystem Dynamics Investigation (GEDI) Structural Verification Unit (SVU) Vibration Test

This presentation describes the vibration test campaign of the Structural Verification Unit for the Global Ecosystem Dynamics Investigation (GEDI) mission The Structural Verification Unit test campaign served multiple purposes including the qualification of the instrument primary structure, verification of the structure's stiffness, Aperture Control Mechanism assembly level verification, and validation of the control approach for protoflight instrument vibration testing. Testing included three axes of sine burst, random, and sine vibration excitation. This test sequence required a high number of response instrumentation sensors that included tri-axial accelerometers and tri-axial force gauges. Multiple response limiting methods that included acceleration, force, and moment measurements were used to ensure the safety of the flight hardware. The lessons and specific test details learned on the structural verification unit test campaign will reduce test risks for the upcoming instrument-level vibration tests.

Structural Verification Unit↗

NASA NTRS2019

Application of a Temperature-Dependent Load Prediction Method to a RUAG Six-Component Block-Type Balance

Temperature-dependent data of a RUAG six-component block-type balance was analyzed to assess the accuracy of two load prediction methods for temperature-dependent balance data. The supplied data was prepared for the analysis by splitting it into calibration and check load data subsets. The first calibration data subset was obtained at a temperature of 294 Kelvin. The second calibration data subset was obtained at a temperature of 315 Kelvin. A subset of 38 points was extracted from the second data set and used as check loads so that the accuracy of the two load prediction methods could be tested. First, the Iterative Method in combination with an extended independent and dependent variable set was used for the balance load prediction. This approach fits electrical outputs as a function of loads and the temperature and, afterwards, constructs a load iteration scheme from the regression coefficients so that loads can be predicted from outputs and the temperature during a wind tunnel test. The Non-Iterative Method was also used for the load prediction. This alternate method can more easily be implemented in a data system as loads are directly fitted as a function of electrical outputs and the temperature. Analysis results for the axial force are only discussed in the paper as similar results were obtained for the other five load components. Results for both methods clearly show that the cross-product term constructed from either a primary gage load or a primary gage output and the temperature explains the majority of the temperature-dependent part of the predicted balance load. This term models the temperature dependent nature of the gage sensitivity. Therefore, it is recommended to apply primary gage loadings at different temperatures during a balance calibration whenever temperature effects need to be described. These loadings will contain information about the temperature-dependent nature of the gage sensitivities that can be quantified by related cross-product terms in regression models of the data.

strain-gage balance↗

NASA NTRS2020

Calibration of the 11x11-Foot Transonic Wind Tunnel at NASA Ames Research Center

A static pipe calibration characterizing the streamwise static pressure distribution was conducted at the 11-By 11-Foot Transonic Wind Tunnel at NASA Ames Research Center. This data is used to determine the local Mach number within the test section and evaluate buoyancy corrections to axial force measurements. The 60 foot long, 6 inch diameter pipe contained 444 static pressure taps spanning the test section and nozzle regions of the tunnel. The forward end of the pipe extends into the settling chamber and is held by four cables mounting to the tunnel shell, and the aft end is fixed on the institutional model support system. A hydraulic cylinder at the aft end of the pipe provides tension on the system to reduce vibration and to keep the pipe as level as possible throughout the test section. The previous calibration was improved upon by using pressure scanners with greater accuracy, ensuring a uniform pressure tube length for each tap to control pneumatic lag, optically tracking any streamwise movement of the pipe, and more tightly controlling the tunnel condition set points. Typically this calibration is conducted with the pipe on tunnel centerline and 33 inches below centerline for sting-mounted models and semi-span (i.e. floor-mounted) models respectively, however schedule demands permitted only the centerline calibration. The semi-span calibration is planned to be completed in the summer of 2020. Immediately following the static pipe calibration, a shorter, 9 foot static pipe used as the calibration check standard was installed to obtain its first post-calibration pressure dataset. This short static pipe consists of 148 static pressure taps distributed along the pipe section and one total pressure tap at the end of an ogive nose. Performing the calibration test and its check standard back-to-back allows this dataset to establish a reliable baseline for future calibration check standard testing. Over time the use of a calibration check standard offers the ability to assess the stability of the calibration through statistical process control in an efficient and costeffective manner, thereby potentially increasing the time required between full tunnel calibrations.

White, Bethany↗

NASA NTRS2001

Ultrasonic/sonic drilling/coring (USDC) for planetary applications

One of the major limitations of sampling on Mars and other low gravity environments is the need for high axial force when using conventional drilling. To address this limitation an ultrasonic/sonic drilling/coring (USDC) mechanism has been developed that employs an ultrasonic horn driven by a piezoelectric stack. The horn dnves a free mass that resonates between the horn and drill stein. Tests have shown that the USDC addresses some of the key challenges to the NASA sampling objectives. The USDC is lightweight (450 g), requires low preload (<5N) and can be driven at low power (5W), The device has been shown to drill rocks with various levels of hardness including granite, diorite, basalt and limestone. The hammering action involved with the coring process can produce cores of various shapes, which need not necessarily be round. Because it is driven by piezoelectric ceramics, the USDC is highly tolerant to changes in its operating environment. These actuation materials can be designed to operate at a wide range of temperatures including those expected on Mars and Venus. Although the drill is driven electrically at 20 kHz, a substantial sub-harmonic acoustic component is found that is crucial to drilling performance. An analytical model has been developed to explain this low frequency coupling in the horn, free mass, drill stem and rock.

Peterson, Thomas↗

NASA NTRS2017

Static Wind Tunnel Testing of a Legged Venus Lander

A static wind tunnel test was conducted to determine the static aerodynamic coe cients of the surface lander design proposed by the Venus In-Situ Atmospheric and Geochemical Explorer (VISAGE). The baseline design of the lander consists of a spherical pressure vessel with a top-mounted circular drag plate for aerodynamic deceleration, and three xed landing legs. A modular subscale lander model, which allowed testing of several drag plate and landing leg con gurations, was fabricated using rapid-prototyping techniques. The model was tested with four di erent drag plates and three di erent leg con gurations, at a dynamic pressure of 1610 Pa and Mach number of 0.15. Testing was conducted using legs of varying diameter in order to determine the appropriate scaling of the results to Reynolds numbers representative of terminal descent at Venus. The static aerodynamic force (axial, normal, and side), and moment (rolling, pitching, yawing) coe cients for each lander con guration were determined as a function of model orientation. All model con gurations were found to be statically stable in the range of total angles of attack considered (0 to 30 deg). However, the drag performance and degree of static stability of the model were dependent on the dihedral angle of the circular drag plate. The results will enable the creation of a preliminary aerodatabase for the VISAGE lander concept, and allow the e ect of design changes on aerodynamic performance to be evaluated.

Rabinovitch, Jason↗

NASA NTRSDate not supplied

Mars Entry, Descent, and Landing Instrumentation 2 Trajectory, Aerodynamics, and Atmosphere Reconstruction

On February 18th, 2021, the Mars 2020 entry system successfully delivered the Perseverance rover to the surface of Mars at Jezero Crater. The entry capsule carried a set of instrumentation installed on the heat shield and backshell, named the Mars Entry, Descent, and Landing Instrumentation 2. The instruments include pressure transducers, thermocouples, heat flux gauges, and radiometers to measure the aerodynamic and aerothermodynamic performance of the entry vehicle. This paper describes the trajectory and atmosphere reconstruction results based on the pressure sensor measurements. The process uses a Kalman filter approach to estimate the freestream atmospheric properties from the pressure measurements combined with a model of the pressure distribution of the heatshield and other sensor inputs, including an inertial measurement unit and other on-board navigation sensors, and several external atmospheric observations. The results indicate upper altitude density was up to 150% higher than nominal, which is consistent with the observed early entry guidance start time. The density below 40 km was within 12% the pre-flight predictions. The reconstructed axial force coefficient was approximately 2% lower than the pre-flight prediction across the flight range.

Christopher D Karlgaard↗

NASA NTRSDate not supplied

Time-Accurate Computational Fluid Dynamics Analysis of a Supersonic Turbine to Assess Structural Mode Excitation

Gas turbines can experience significant unsteady loading during operation which can cause damage such as blade cracking or bearing wear. While computational fluid dynamics (CFD) modeling of full three-dimensional gas turbine flow to verify meanline design performance is standard practice within the industry, the use of time-accurate CFD makes it possible to assess the unsteady loading which can be especially problematic at operating conditions where unsteady fluid loading aligns with structural modes. The Fluid Dynamics branch (ER42) at NASA Marshall Space Flight Center has developed a time-accurate CFD analysis methodology using the unstructured, density-based, Loci-CHEM solver which is capable of simulating the relative motion required for turbomachinery applications through sliding interface meshes. The highly-parallel unstructured solver allows for full three-dimensional, time-accurate simulation of turbines including upstream and downstream components such as manifolds, nozzles, and stators, any of which could excite a turbine structural mode. Recently, Loci-CHEM was used to analyze the FASTRAC supersonic turbine to assess the loading on the rotor. Overall performance and time-averaged loading on the rotor was computed, including the axial force over the entire rotor disk which is required for force balance calculations on the turbopump. The FASTRAC turbine has supersonic nozzles upstream of the rotor that result in significant unsteady loading on the rotor blades at multiples of the nozzle pass frequency. The unsteady blade pressure loading was decomposed into the frequency domain for direct use in structural forced response analysis. Utilizing this type of CFD analysis coupled with structural analysis has proven to be a valuable tool in identifying structural modes that are being excited by unsteady fluid loading.

M.V. Fischels↗

NASA NTRSDate not supplied

Time-Accurate Computational Fluid Dynamics Analysis of a Supersonic Turbine to Assess Structural Mode Excitation

Gas turbines can experience significant unsteady loading during operation which can cause damage such as blade cracking or bearing wear. While computational fluid dynamics (CFD) modeling of full three-dimensional gas turbine flow to verify meanline design performance is standard practice within the industry, the use of time-accurate CFD makes it possible to assess the unsteady loading which can be especially problematic at operating conditions where unsteady fluid loading aligns with structural modes. The Fluid Dynamics branch (ER42) at NASA Marshall Space Flight Center has developed a time-accurate CFD analysis methodology using the unstructured, density-based, Loci-CHEM solver which is capable of simulating the relative motion required for turbomachinery applications through sliding interface meshes. The highly-parallel unstructured solver allows for full three-dimensional, time-accurate simulation of turbines including upstream and downstream components such as manifolds, nozzles, and stators, any of which could excite a turbine structural mode. Recently, Loci-CHEM was used to analyze the FASTRAC supersonic turbine to assess the loading on the rotor. Overall performance and time-averaged loading on the rotor was computed, including the axial force over the entire rotor disk which is required for force balance calculations on the turbopump. The FASTRAC turbine has supersonic nozzles upstream of the rotor that result in significant unsteady loading on the rotor blades at multiples of the nozzle pass frequency. The unsteady blade pressure loading was decomposed into the frequency domain for direct use in structural forced response analysis. Utilizing this type of CFD analysis coupled with structural analysis has proven to be a valuable tool in identifying structural modes that are being excited by unsteady fluid loading.

M V Fischels↗

NASA NTRSDate not supplied

Exploring the Accuracy of RANS Simulations for Mars Entry Vehicles

Accurate yet inexpensive predictions of aerodynamic coefficients for Mars entry vehicles have remained a consistent challenge over the past five decades. Below Mach 6, drag on the backshell becomes significant and must be accurately predicted. Steady Reynolds-averaged Navier-Stokes (RANS) models are commonly used, despite their poor predictions of backshell pressure. While scale-resolving simulations have shown promise in the past decade, there is still a need for cheap, accurate RANS predictions for large aerodynamic databases. The Mars Science Laboratory (MSL) is used as a case study to examine predictive accuracy and known shortcomings for RANS predictions of Mars entry vehicles. Several different grid generation techniques are compared, including a comparison between prismatic boundary layer grids and fully unstructured, tetrahedral grids. Comparisons are made to experimental data for Mach 2.5, 3.5, and 4.5. The accuracy of predicted aerodynamic coefficients is examined. Overpredictions in axial force and drag are explained by a closer examination of the surface pressure. These findings document sensitivities and best practices for future RANS database development of Mars entry vehicles.

RANS↗

NASA NTRSDate not supplied

Exploring the Accuracy of RANS Simulations for Mars Entry Vehicles

Accurate yet inexpensive predictions of aerodynamic coefficients for Mars entry vehicles have remained a consistent challenge over the past five decades. Below Mach 6, drag on the backshell becomes significant and must be accurately predicted. Steady Reynolds-averaged Navier-Stokes (RANS) models are commonly used, despite their poor predictions of backshell pressure. While scale-resolving simulations have shown promise in the past decade, there is still a need for cheap, accurate RANS predictions for large aerodynamic databases. The Mars Science Laboratory (MSL) is used as a case study to examine predictive accuracy and known shortcomings for RANS predictions of Mars entry vehicles. Several different grid generation techniques are compared, including a comparison between prismatic boundary layer grids and fully unstructured, tetrahedral grids. Comparisons are made to experimental data for Mach 2.5, 3.5, and 4.5. The accuracy of predicted aerodynamic coefficients is examined. Overpredictions in axial force and drag are explained by a closer examination of the surface pressure. These findings document sensitivities and best practices for future RANS database development of Mars entry vehicles.

CFD↗

NASA NTRSDate not supplied

Space Launch System Base Aerodynamics Post-Flight Reconstruction for Artemis I

Artemis I was the first uncrewed integrated test flight of the NASA heavy-lift, human-rated, exploration-class launch vehicle, Space Launch System (SLS), and Orion spacecraft. Artemis I successfully launched from Pad39B at NASA Kennedy Space Center on November 16th, 2022. The integrated test flight was composed of launch and ascent of SLS vehicle from lift-off to RS-25 main engine cut-off (MECO), interim cryogenic propulsion stage (ICPS) in-space flight and Orion’s trajectory around the moon and landing in the Pacific Ocean which occurred on December 11th, 2022. The SLS total thrust of 8,800,000 lbf was powered by four LOX/LH2 RS-25 engines and two 5-segment solid rocket boosters. As a result, the base flow field had highly complex phenomena and regimes. SLS base aerodynamics covers vehicle base pressure and integrated axial force during powered flight from lift-off to MECO. This work discusses the SLS base flow physics observed during Artemis I and comparisons of post-flight reconstruction with pre-flight models and Space Shuttle data. This was the first time in-depth base aerodynamics flight reconstruction has been investigated for an exploration-class launch vehicle since the Saturn V Program.

aerothermodynamics↗

NASA NTRSDate not supplied

Base Aerodynamics Post-Flight Reconstruction for Artemis I

Artemis I was the first uncrewed integrated test flight of the NASA heavy-lift, human-rated, exploration-class launch vehicle, Space Launch System (SLS), and Orion spacecraft. Artemis I successfully launched from Pad39B at NASA Kennedy Space Center on November 16th, 2022. The integrated test flight was composed of launch and ascent of SLS vehicle from lift-off to RS-25 main engine cut-off (MECO), interim cryogenic propulsion stage (ICPS) in-space flight and Orion’s trajectory around the moon and landing in the Pacific Ocean which occurred on December 11th, 2022. The SLS total thrust of 8,800,000 lbf was powered by four LOX/LH2 RS-25 engines and two 5-segment solid rocket boosters. As a result, the base flow field had highly complex phenomena and regimes. SLS base aerodynamics covers vehicle base pressure and integrated axial force during powered flight from lift-off to MECO. This work discusses the SLS base flow physics observed during Artemis I and comparisons of post-flight reconstruction with pre-flight models and Space Shuttle data. This was the first time in-depth base aerodynamics flight reconstruction has been investigated for an exploration-class launch vehicle since the Saturn V Program.

aerothermodynamics↗

NASA NTRSDate not supplied

Computational Modeling of Two Mars Powered Descent Vehicle Concepts Tested in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not suitable for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). This paper covers computational flowfield predictions completed at wind tunnel conditions and comparisons to the test data. On the blowing HIAD models, the time-averaged pressure inboard of the nozzles was generally well-predicted, especially if the nozzles are canted outward, when the nozzles are located further from the nose. At intermediate CobraMRV thrust coefficients, CFD pressures are more accurately predicted than they are for the HIAD models, largely due to the nozzle locations and pointing directions. Overall, the CFD pressure coefficients were predicted within 0.2 of the steady pressure measurements for all blowing models, with smaller discrepancies at higher HIAD thrust, and larger discrepancies at lower HIAD CobraMRV thrust. All HIAD models were predicted to have a gradually decreasing axial force coefficient as the total thrust increases, in agreement with available pressure sensitive paint data. On models with canted nozzles or with nozzles further from the nose, the force coefficient was slightly higher for a given thrust. On the CobraMRV model, the CFD also shows consistent results between solvers and follows trends revealed in the data; the aerodynamic force coefficient remains near the non-blowing value at a tunnel Mach number of 2.4 regardless of thrust, and increases above that level at a Mach number of 3.5, consistent with the discrete pressure data. CFD analysis at tunnel and flight conditions will continue as flight system designs concepts mature.

Supersonic Retropropulsion↗

NASA NTRSDate not supplied

Computational Modeling of Two Mars Powered Descent Vehicle Concepts Tested in the Langley Unitary Plan Wind Tunnel

Future human Mars missions will require powered descent starting at supersonic conditions, something which has never been done before at Mars. Computational powered descent flowfield simulations have been completed at full-scale Mars conditions, but the available ground test data are not suitable for calibrating computational uncertainties for aerodynamic interference on proposed Mars descent vehicles. Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). This paper covers computational flowfield predictions completed at wind tunnel conditions and comparisons to the test data. On the blowing HIAD models, the time-averaged pressure inboard of the nozzles was generally well-predicted, especially if the nozzles are canted outward, when the nozzles are located further from the nose. At intermediate CobraMRV thrust coefficients, CFD pressures are more accurately predicted than they are for the HIAD models, largely due to the nozzle locations and pointing directions. Overall, the CFD pressure coefficients were predicted within 0.2 of the steady pressure measurements for all blowing models, with smaller discrepancies at higher HIAD thrust, and larger discrepancies at lower HIAD CobraMRV thrust. All HIAD models were predicted to have a gradually decreasing axial force coefficient as the total thrust increases, in agreement with available pressure sensitive paint data. On models with canted nozzles or with nozzles further from the nose, the force coefficient was slightly higher for a given thrust. On the CobraMRV model, the CFD also shows consistent results between solvers and follows trends revealed in the data; the aerodynamic force coefficient remains near the non-blowing value at a tunnel Mach number of 2.4 regardless of thrust, and increases above that level at a Mach number of 3.5, consistent with the discrete pressure data. CFD analysis at tunnel and flight conditions will continue as flight system designs concepts mature.

Supersonic Retropropulsion↗

NASA NTRS1982

Experiment measurement of Alford's force in axial-flow turbomachinery

Results of experimental measurements made on a small high speed, axial flow test apparatus are presented to verify the existence of Alford's force (that circumferential variation of blade-tip clearances in axial-flow turbomachinery will produce cross-coupled (normal to the eccentricity) aerodynamic forces on the rotor) and to investigate the validity of his mathematical prediction model.

Vance, J. M.↗

NASA NTRS2005

CFD Simulation of Casing Treatment of Axial Flow Compressors

A computational study is carried out to understand the physical mechanism responsible for the improvement in stall margin of an axial flow rotor due to the circumferential casing grooves. It is shown that the computational tool used predicts an increase in operating range of the rotor when casing grooves are present. A budget of the axial momentum equation is carried out at the rotor casing in the tip gap in order to uncover the physical process behind this stall margin improvement. It is shown that for the smooth casing the net axial pressure force . However in the presence of casing grooves the net axial shear stress force acting at the casing is augmented by the axial force due to the radial transport of axial momentum, which occurs across the grooves and power stream interface. This additional force adds to the net axial viscous sheer force and thus leads to an increase in the stall margin of the rotor.

DeWitt, Kenneth↗

NASA NTRS1982

Unsteady aerodynamics and motions of the Pioneer Venus probes

Helicopter drop tests were made of models of the Pioneer Venus probe descent configurations to characterize their unsteady forces and angular dynamics in equilibrium descent. The axial and normal forces were found to be unsteady in magnitude by about 10 and 5% of the mean axial force, respectively. A cycle of the axial variation takes place in flight distances of from 15 to 40 diameters. The unsteadiness almost certainly is associated with the wake. Angular motions which do not converge to zero angle of attack even in very long duration descent are excited by the unsteady pitching moments. The nearly spherical large probe model was aerodynamically more unsteady than the round-nosed conical small probe model. Data returned from Venus by the Pioneer Venus probes show unsteady axial forces and angular motions similar to those seen in the drop tests.

Seiff, A.↗