Search NASA⌕ Search

SEARCH · Search NASA

Results for “BENDING VIBRATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Elastomer damper performance - A comparison with a squeeze film for a supercritical power transmission shaft

This paper describes the design and testing of an elastomer damper on a super-critical power transmission shaft. The elastomers were designed to provide acceptable operation through the fourth bending mode and to control synchronous as well as nonsynchronous vibration throughout the operating range. The design of the elastomer was such that it could be incorporated into the system as a replacement for a squeeze-film damper without a reassembly, which could have altered the imbalance of the shaft. This provided a direct comparison of the elastomer and squeeze-film dampers without having to assess the effect of shaft imbalance changes.

Zorzi, E. S.↗
NASA NTRS1986

Dynamic analysis and experiment methods for a generic space station model

Modal vibration tests in conjunction with finite element analysis were used to characterize a generic dynamic model. The model consists of five substructures to simulate the multi-body, low frequency nature of large space structures. Static tests were used to refine the substructure analytical models prior to full assemblage analysis. The effects of a cable suspension system are analyzed using prestressed vibration analysis. Coupling between a cable suspension mode and model bending mode is shown to be influenced by the distance from the model center of gravity to the cable-to-model attachment location. A damping characterization method using noncontacting exciters was used to measure amplitude dependent damping. Frequency and damping measurements in ambient air and at near-vacuum conditions are presented.

Belvin, W. K.↗
NASA NTRS1998

Fourier Transform Infrared (FT-IR) Spectroscopy of Atmospheric Trace Gases HCl, NO and SO2

Fourier Transform Infrared (FT-IR) spectral data have been recorded in the spectral region 400-4000/cm of hydrogen chloride and sulfur dioxide with I/cm resolution and of nitric oxide with 0.25 cm-i resolution, under quasi-static conditions, when the sample gas was passed through tubings of aluminum, copper, stainless steel and teflon. The absorbance was measured for the rotational lines of the fundamental bands of (1)H(35)Cl and (1)H(37)Cl for pressures in the range 100-1000 Torr and for the (14)N(16)O molecule in the range 100-300 Torr. The absorbance was also measured for individual rotational lines corresponding to the three modes of vibrations (upsilon(sub 1) - symmetric stretch, upsilon(sub 2) - symmetric bend, upsilon(sub 3) - anti-symmetric stretch) of the SO2 molecule in the pressure range 25-150 Torr. A graph of absorbance versus pressure was plotted for the observed rotational transitions of the three atmospherically significant molecules, and it was found that the absorbance was linearly proportional to the pressure range chosen, thereby validating Beer's law. The absorption cross-sections were determined from the graphical slopes for each rotational transition recorded for the HCl, NO and SO2 species. Qualitative and quantitative spectral changes in the FT-IR data will be discussed to identify and characterize various tubing materials with respect to their absorption features.

Haridass, C.↗
NASA NTRS1920

Experience with Geared Propeller Drives for Aviation Engines

I. The development of the gear wheels: (a) bending stresses; (b) compressive stresses; (c) heating; (d) precision of manufacture. II. General arrangement of the gearing. III. Vibration in the shaft transmission. An overview is given of experience with geared propeller drives for aviation engines. The development of gear wheels is discussed with emphasis upon bending stresses, compressive stresses, heating, and precision in manufacturing. With respect to the general arrangement of gear drives for airplanes, some principal rules of mechanical engineering that apply with special force are noted. The primary vibrations in the shaft transmission are discussed. With respect to vibration, various methods for computing vibration frequency and the influence of elastic couplings are discussed.

Kutzbach, K↗
NASA NTRS1993

Active Suppression Of Vibrations On Elastic Beams

Pairs of colocated piezoelectric transducers, independently controlled by multichannel adaptive controller, employed as actuators and sensors to achieve simultaneous attenuation of both extensional and flexural motion. Single pair used to provide simultaneous control of flexural and extensional waves, or two pairs used to control torsional motion also. Capability due to nature of piezoelectric transducers, when bonded to surfaces of structures and activated by oscillating voltages, generate corresponding oscillating distributions of stresses in structures. Phases and amplitudes of actuator voltages adjusted by controller to impede flow of vibrational energy simultaneously, in waves of various forms, beyond locations of actuators. Concept applies equally to harmonic or random response of structure and to multiple responses of structure to transverse bending, torsion, and compression within structural element. System has potential for many situations in which predominant vibration transmission path through framelike structure.

Silcox, Richard J.↗
NASA NTRS2002

Equivalent-Continuum Modeling With Application to Carbon Nanotubes

A method has been proposed for developing structure-property relationships of nano-structured materials. This method serves as a link between computational chemistry and solid mechanics by substituting discrete molecular structures with equivalent-continuum models. It has been shown that this substitution may be accomplished by equating the vibrational potential energy of a nano-structured material with the strain energy of representative truss and continuum models. As important examples with direct application to the development and characterization of single-walled carbon nanotubes and the design of nanotube-based devices, the modeling technique has been applied to determine the effective-continuum geometry and bending rigidity of a graphene sheet. A representative volume element of the chemical structure of graphene has been substituted with equivalent-truss and equivalent continuum models. As a result, an effective thickness of the continuum model has been determined. This effective thickness has been shown to be significantly larger than the interatomic spacing of graphite. The effective thickness has been shown to be significantly larger than the inter-planar spacing of graphite. The effective bending rigidity of the equivalent-continuum model of a graphene sheet was determined by equating the vibrational potential energy of the molecular model of a graphene sheet subjected to cylindrical bending with the strain energy of an equivalent continuum plate subjected to cylindrical bending.

Odegard, Gregory M.↗
NASA NTRS2008

Structural Dynamic Analysis of a Spacecraft Multi-DOF Shaker Table

Finite element enforced response analysis was performed on a three axis expander head shaker table to aid in the design of the table structure and vibration control system. The payload for this shaker system is a generic spacecraft with a multitude of flexible modes across a broad frequency band. A Craig-Bampton representation of the spacecraft was used to expedite analysis of multiple shaker table designs. The analysis examines the required forces in the actuators for a constant amplitude base acceleration sine sweep test, the resulting forces in the spacecraft and table attachment restraints, and the resulting accelerations on the spacecraft structure. The results show the spacecraft response is very high at the spacecraft center of gravity (CG) due to the high CG offset and cantilever effect of the low frequency spacecraft bending modes. The high response can be addressed by "notching" the input vibration levels to avoid over-testing the spacecraft. At frequencies above 25 Hz, the spacecraft modal effective masses are very small, and the response of the shaker table dominates the response. Anti-resonances of the shaker table in the frequency range of interest reduce the acceleration output and require much higher actuator forces to achieve the acceleration specification. These effects may require stiffening the shaker structure to move the modes out of the test frequency range or increasing the shaker table damping.

Pray, Carl↗
NASA NTRS1973

Sensitivity of rotor blade vibration characteristics to torsional oscillations.

A theoretical investigation of dynamic response characteristics of helicopter rotor blades in forward flight was carried out with special emphasis on the torsional degrees-of-freedom. The finite element method was applied in the formulation of the coupled equations of motion for flapwise bending and torsion for blades with non-collinear elastic, mass and aerodynamic axes. The sensitivity of blade vibration characteristics with respect to structural, geometric and aerodynamic properties as well as flight conditions was evaluated. Numerical results for sample blades were plotted to show the variation of the coupling between bending and torsional components of the response.

Bratanow, T.↗
NASA NTRS1972

Energy curves of CO2/-/.

Ab initio energy curves of the A super 2 sub 1 and B super 2 sub 1 states of CO2(-) have been obtained as a function of the bending angle. An analysis shows that gaseous CO2(-) in its ground vibrational level can have a relatively long life since the ion energy in the neighborhood of the ion equilibrium geometry is about 1 eV below the neutral molecule energy for that geometry.

Krauss, M.↗
NASA NTRS1981

Interlocking wedge joint is easily assembled

Wedge joint links structural members in manual, remote, or automated assemblies. Joint is simple enough to be assembled by undersea divers, workers in nuclear reactors, and other wearing gloves or bulky clothing. Combination of wedging angles on parts overcomes structural misalinements and forces assembly into true position as locking sleeve moves into place. Joint transmits tension, compression, bending moments and torsion and is inherently insensitive to thermal excursions, vibration, and machining tolerance buildup.

Long, M. J.↗
NASA NTRS1995

Detecting gear tooth fracture in a high contact ratio face gear mesh

This paper summarized the results of a study in which three different vibration diagnostic methods were used to detect gear tooth fracture in a high contact ratio face gear mesh. The NASA spiral bevel gear fatigue test rig was used to produce unseeded fault, natural failures of four face gear specimens. During the fatigue tests, which were run to determine load capacity and primary failure mechanisms for face gears, vibration signals were monitored and recorded for gear diagnostic purposes. Gear tooth bending fatigue and surface pitting were the primary failure modes found in the tests. The damage ranged from partial tooth fracture on a single tooth in one test to heavy wear, severe pitting, and complete tooth fracture of several teeth on another test. Three gear fault detection techniques, FM4, NA4*, and NB4, were applied to the experimental data. These methods use the signal average in both the time and frequency domain. Method NA4* was able to conclusively detect the gear tooth fractures in three out of the four fatigue tests, along with gear tooth surface pitting and heavy wear. For multiple tooth fractures, all of the methods gave a clear indication of the damage. It was also found that due to the high contact ratio of the face gear mesh, single tooth fractures did not significantly affect the vibration signal, making this type of failure difficult to detect.

Zakrajsek, James J.↗
NASA NTRS1983

Transverse vibration and buckling of a cantilevered beam with tip body under constant axial base acceleration

The planar transverse bending behavior of a uniform cantilevered beam with rigid tip body subject to constant axial base acceleration was analyzed. The beam is inextensible and capable of small elastic transverse bending deformations only. Two classes of tip bodies are recognized: (1) mass centers located along the beam tip tangent line; and (2) mass centers with arbitrary offset towards the beam attachment point. The steady state response is studied for the beam end condition cases: free, tip mass, tip body with restricted mass center offset, and tip body with arbitrary mass center offset. The first three cases constitute classical Euler buckling problems, and the characteristic equation for the critical loads/accelerations are determined. For the last case a unique steady state solution exists. The free vibration response is examined for the two classes of tip body. The characteristic equation, eigenfunctions and their orthogonality properties are obtained for the case of restricted mass center offset. The vibration problem is nonhomogeneous for the case of arbitrary mass center offset. The exact solution is obtained as a sum of the steady state solution and a superposition of simple harmonic motions.

Storch, J.↗
NASA NTRS1974

Sensitivity analysis of torsional vibration characteristics of helicopter rotor blades. Part 1: Structural dynamics analysis

A theoretical investigation of structural vibration characteristics of rotor blades was carried out. Coupled equations of motion for flapwise bending and torsion were formulated for rotor blades with noncollinear elastic and mass axes. The finite element method was applied for a detailed representation of blade structural properties. Coupled structural mass and stiffness coefficients were evaluated. The range of validity of a set of coupled equations of motion linearized with respect to eccentricity between elastic and mass axes was investigated. The sensitivity of blade vibration characteristics to torsion were evaluated by varying blade geometric properties, boundary conditions, and eccentricities between mass and elastic axes.

Bratanow, T.↗
NASA NTRS1983

Vibration response of geometrically nonlinear elastic beams to pulse and impact loading

The governing equations for the geometrically nonlinear deformation of elastic beams subjected to dynamic bending loads are developed and solved for various initial conditions. Of primary interest is the response to pulse loading and simulated impact. Both transient and several cycle solutions are generated for the free vibration response to pulse loading. The results obtained are compared to a first mode analysis approximation. A model is developed to simulate impact loading by the distribution of additional mass to the elastic system and subjecting it to a velocity pulse. The governing equations are solved using second order finite differences in space and time. The solutions obtained are in reasonable agreement with experimental results.

Liebowitz, H.↗
NASA NTRS1974

Effects of curvilinear motion in large-amplitude bending of C3

The geometry of the bending of a linear triatomic molecule is analyzed, and an expression for the average rotational constant is derived. A harmonic oscillator model of C3 is fitted to the observed rotational constant within 0.6%. The bond distance between atoms at zero bending is 1.287 A according to this model; this is noticeably larger than the average internuclear distance of 1.277 A for the vibrational ground state. The first order perturbation solutions for the vibrational energy levels, taking into account the effect of a quartic perturbation potential, closely match observed levels. For a square well potential model of C3, the effect of curvilinear motion in bending is similar to that found for the harmonic oscillator model, though the decreases in energy are about twice as large. In both models, the average energy decrease is relatively constant at approximately 10% over a wide range of vibrational quantum number.

Hansen, C. F.↗
NASA NTRS1989

Active control of gust- and interference-induced vibration of tilt-rotor aircraft

An active control system to suppress the response of the blade bending modes of a tilt-rotor aircraft to axial gusts and wing/rotor interference is described. The use of blade-mounted accelerometers as sensors is shown to permit the measurement and control of tilt-rotor blade modal responses and their associated vibratory loads directly. The feedback of modal acceleration, in addition to modal rate and displacement, is demonstrated to provide a control phase lead, in comparison with feedback of modal rate and displacement only, which makes higher system gains achievable.

Ham, Norman D.↗