Results for “Ballistic Range” — Page 14

NASA NTRS2000

Earth Return Aerocapture for the TransHab/Ellipsled Vehicle

The current architecture being considered by NASA for a human Mars mission involves the use of an aerocapture procedure at Mars arrival and possibly upon Earth return. This technique would be used to decelerate the vehicles and insert them into their desired target orbits, thereby eliminating the need for propulsive orbital insertions. The crew may make the interplanetary journey in a large, inflatable habitat known as the TransHab. It has been proposed that upon Earth return, this habitat be captured into orbit for use on subsequent missions. In this case, the TransHab would be complimented with an aeroshell, which would protect it from heating during the atmospheric entry and provide the vehicle with aerodynamic lift. The aeroshell has been dubbed the "Ellipsled" because of its characteristic shape. This paper reports the results of a preliminary study of the aerocapture of the TransHab/Ellipsled vehicle upon Earth return. Undershoot and overshoot boundaries have been determined for a range of entry velocities, and the effects of variations in the atmospheric density profile, the vehicle deceleration limit, the maximum vehicle roll rate, the target orbit, and the vehicle ballistic coefficient have been examined. A simple, 180 degree roll maneuver was implemented in the undershoot trajectories to target the desired 407 km circular Earth orbit. A three-roll sequence was developed to target not only a specific orbital energy, but also a particular inclination, thereby decreasing propulsive inclination changes and post-aerocapture delta-V requirements. Results show that the TransHab/Ellipsled vehicle has a nominal corridor width of at least 0.7 degrees for entry speeds up to 14.0 km/s. Most trajectories were simulated using continuum flow aerodynamics, but the impact of high-altitude viscous effects was evaluated and found to be minimal. In addition, entry corridor comparisons have been made between the TransHab/Ellipsled and a modified Apollo capsule which is also being considered as the crew return vehicle; because of its slightly higher lift-to-drag ratio, the TransHab has a modest advantage with regard to corridor width. Stagnation-point heating rates and integrated heat loads were determined for a range of vehicle ballistic coefficients and entry velocities.

Muth, W. D.↗

NASA NTRS1991

Single wall penetration equations

Five single plate penetration equations are compared for accuracy and effectiveness. These five equations are two well-known equations (Fish-Summers and Schmidt-Holsapple), two equations developed by the Apollo project (Rockwell and Johnson Space Center (JSC), and one recently revised from JSC (Cour-Palais). They were derived from test results, with velocities ranging up to 8 km/s. Microsoft Excel software was used to construct a spreadsheet to calculate the diameters and masses of projectiles for various velocities, varying the material properties of both projectile and target for the five single plate penetration equations. The results were plotted on diameter versus velocity graphs for ballistic and spallation limits using Cricket Graph software, for velocities ranging from 2 to 15 km/s defined for the orbital debris. First, these equations were compared to each other, then each equation was compared with various aluminum projectile densities. Finally, these equations were compared with test results performed at JSC for the Marshall Space Flight Center. These equations predict a wide variety of projectile diameters at a given velocity. Thus, it is very difficult to choose the 'right' prediction equation. The thickness of a single plate could have a large variation by choosing a different penetration equation. Even though all five equations are empirically developed with various materials, especially for aluminum alloys, one cannot be confident in the shield design with the predictions obtained by the penetration equations without verifying by tests.

Hayashida, K. B.↗

NASA NTRS1958

A Comparative Analysis of the Performance of Long-Range Hypervelocity Vehicles

Long-range hypervelocity vehicles are studied in terms of their motion in powered flight. Powered flight is analyzed for an idealized propulsion system which approximates rocket motors. Unpowered flight is characterized by a return to earth along a ballistic, skip, or glide trajectory. Only those trajectories are treated which yield the maximum range for a given velocity at the end of powered flight. Aerodynamic heating is treated in a manner similar to that employed previously by the senior authors in studying ballistic missiles (NACA rep. 1381), with the exception that radiant as well as convective heat transfer is considered in connection with glide and skip vehicles. As a final performance consideration, it is shown that on the basis of equal ratios of mass at take-off to mass at the end of powered flight, the hypervelocity vehicle compares favorably with the supersonic airplane for ranges in the neighborhood of and greater than one half the circumference of the earth. In the light of this and previous findings, it is concluded that the ballistic and glide vehicles have, in addition to the advantages usually ascribed to great speed, the attractive possibility of providing relatively efficient long-range flight.

Eggers, Alfred J , Jr↗

NASA NTRS2006

Trajectory and Aeroheating Environment Development and Sensitivity Analysis for Capsule-shaped Vehicles

Recently, NASA's Exploration Systems Research and Technology Project funded several tasks that endeavored to develop and evaluate various thermal protection systems and high temperature material concepts for potential use on the crew exploration vehicle. In support of these tasks, NASA Langley's Vehicle Analysis Branch generated trajectory information and associated aeroheating environments for more than 60 unique entry cases. Using the Apollo Command Module as the baseline entry system because of its relevance to the favored crew exploration vehicle design, trajectories for a range of lunar and Mars return, direct and aerocapture Earth-entry scenarios were developed. For direct entry, a matrix of cases was created that reflects reasonably expected minimum and maximum values of vehicle ballistic coefficient, inertial velocity at entry interface, and inertial flight path angle at entry interface. For aerocapture, trajectories were generated for a range of values of initial velocity and ballistic coefficient that, when combined with proper initial flight path angles, resulted in achieving a low Earth orbit either by employing a full lift vector up or full lift vector down attitude. For each trajectory generated, aeroheating environments were generated which were intended to bound the thermal protection system requirements for likely crew exploration vehicle concepts. The trades examined clearly pointed to a range of missions / concepts that will require ablative systems as well as a range for which reusable systems may be feasible. In addition, the results clearly indicated those entry conditions and modes suitable for manned flight, considering vehicle deceleration levels experienced during entry. This paper presents an overview of the analysis performed, including the assumptions, methods, and general approach used, as well as a summary of the trajectory and aerothermal environment information that was generated.

Robinson, Jeffrey S.↗

NASA NTRS1987

On the simulation of ballistic shock loads

Blast or penetrator-impact induced shocks are characterized by high acceleration levels, particularily in the higher frequency range and for a short time duration. These shocks are dangerous for the equipment of ships, combat vehicles, airplanes or spacecraft structures. As ballistic shock loads are insufficiently simulated by laboratory test machines, researchers designed a ballistic shock simulator. The impact induced shocks are simulated by an explosive and the vehicle to be bombarded is replaced by a simplified structure. This structure is suitable to accommodate any equipment which can be tested up to their load limits.

Hollburg, Uwe↗

DOE OSTI2023

Shock behavior of materials

The physics governing the response of materials to shock loading has many applications in various fields, ranging from Earth and planetary science to engineering and ballistics. Elucidating the behavior of materials experiencing the passage of shock waves motivates active research worldwide, including experimental developments with in situ and time-resolved measurements, modern computational approaches, and multi-scale simulations.

36 MATERIALS SCIENCE↗

NASA NTRS1992

A comparative study between experimental results and numerical predictions of multi-wall structural response to hypervelocity impact

Over the last three decades, multiwall structures have been analyzed extensively, primarily through experiment, as a means of increasing the protection afforded to spacecraft structure. However, as structural configurations become more varied, the number of tests required to characterize their response increases dramatically. As an alternative, numerical modeling of high-speed impact phenomena is often being used to predict the response of a variety of structural systems under impact loading conditions. This paper presents the results of a preliminary numerical/experimental investigation of the hypervelocity impact response of multiwall structures. The results of experimental high-speed impact tests are compared against the predictions of the HULL hydrodynamic computer code. It is shown that the hypervelocity impact response characteristics of a specific system cannot be accurately predicted from a limited number of HULL code impact simulations. However, if a wide range of impact loadings conditions are considered, then the ballistic limit curve of the system based on the entire series of numerical simulations can be used as a relatively accurate indication of actual system response.

Schonberg, William P.↗

NASA NTRS2005

Length dependence of carbon nanotube thermal conductivity and the "problem of long waves"

We present the first calculations of finite length carbon nanotube thermal conductivity that extend from the ballistic to the diffusive regime, throughout a very wide range of lengths and temperatures. The long standing problem of vanishing scattering of the "long wavelength phonf dramatically here, making the thermal conductivity diverge as the nanotube length increases. We show that the divergence disappears if 3-phonon scattering processes are considered to second or higher order. Nevertheless, for defect free nanotubes, the thermal conductivity keeps increasing up to very large lengths (10 gm at 300 K). Defects in the nanotube are also able to remove the long wavelength divergence.

Evaluation Studies↗

NASA NTRSDate not supplied

Mission Design Considerations for Robotic Lunar and Gateway Payload Return

A selection of lunar return trajectories is examined and assessed in terms of payload mass, vehicle mass, mission time, mission complexity, and total delta-V using a range of assumptions for the mission design based on historical precedence and near-future vehicle availability. Direct surface return trajectories using a single burn solution are compared with a range of Near-Rectilinear Halo Orbit return and Ballistic Return Trajectories. This study weighs anticipated mission needs, requirements and constraints with the aim of assessing the feasibility of commercial lunar cargo and/or sample return options utilizing NASA’s Gateway and Deep Space Logistics project.

lunar↗

NASA NTRS2019

A Titan gravity-assist technique for ballistic tours skimming over the rings of Saturn

A novel type of Titan-flyby orbits featuring passes of the Saturn rings at close range has been recently discovered. The purpose of this study is to explore the trajectory design space and assess the applicability of such orbits to the design of a Saturn Ring Tour mission concept. A set of initial conditions required to start a tour of the rings is first determined and a flyby sequence to maximize the science observation time over desired ring regions in terms of range distance, relative velocity and duration is then selected. To demonstrate the potential of this technique, a sample high-fidelity ballistic ring tour is detailed.

Tiscareno, Matthew↗

NASA NTRS1955

A comparative analysis of the performance of long-range hypervelocity vehicles

Long-range hypervelocity vehicles are studied in terms of their motion in powered flight, and their motion and aerodynamic heating in unpowered flight. Powered flight is analyzed for an idealized propulsion system which rather closely approaches present-day rocket motors. Unpowered flight is characterized by a return to earth along a ballistic, skip, or glide trajectory. Only those trajectories are treated which yield the maximum range for a given velocity at the end of powered flight. Aerodynamic heating is treated in a manner similar to that employed previously by the senior authors is studying ballistic missiles (NACA RM A53D28), with the exception that radiant as well as convective heat transfer is considered in connection with glide and skip vehicles. The ballistic vehicle is found to be the least efficient of the several types studied in the sense that it generally requires the highest velocity at the end of powered flight in order to attain a given range. This disadvantage may be offset, however, by reducing convective heat transfer to the re-entry body through the artifice of increasing pressure drag in relation to friction drag - that is, by using a blunt body. Thus the kinetic energy required by the vehicle at the end of powered flight may be reduced by minimizing the mass of coolant material involved.

Eggers, Alfred J , Jr↗

NASA NTRS1992

Damage tolerance of a composite sandwich with interleaved foam core

A composite sandwich panel consisting of carbon fiber-reinforced plastic (CFRP) skins and a syntactic foam core was selected as an appropriate structural concept for the design of wind tunnel compressor blades. Interleaving of the core with tough interlayers was done to prevent core cracking and to improve damage tolerance of the sandwich. Simply supported sandwich beam specimens were subjected to low-velocity drop-weight impacts as well as high velocity ballistic impacts. The performance of the interleaved core sandwich panels was characterized by localized skin damage and minor cracking of the core. Residual compressive strength (RCS) of the skin, which was derived from flexural test, shows the expected trend of decreasing with increasing size of the damage, impact energy, and velocity. In the case of skin damage, RCS values of around 50 percent of the virgin interleaved reference were obtained at the upper impact energy range. Based on the similarity between low-velocity and ballistic-impact effects, it was concluded that impact energy is the main variable controlling damage and residual strength, where as velocity plays a minor role.

Ishai, Ori↗

NASA NTRS1990

Theoretical hypervelocity ballistic limit for single or double plates using nonlinear modal analysis

The original research on the use on nonlinear vibration technique to solve for the hypervelocity ballistic limit for double plates is examined. Such structure is commonly found in typical Space Station design where the incoming space or man-made debris would be fragmented upon hitting the outer plate (shield) and the subsequent impact on the main wall would result in a much reduced damge of the space station or spacecraft. The existing few theoretical impact equations do not agree well with each other. The existing computer code bumper used at NASA-Johnson Space Center appears to predict an unconservative ballistic limit when compared with experimental data where the velocity ranges from 3 km/s to 8 km/s. Such unconservative prediction is unacceptable from a practical safe design point of view. The bumper code is based on Wilkinson's (1968) paper and his equations have not been improved nor modified even though they are viewed with suspicion due to lack of agreement with experiments. To make matters worse, there is not another theory which is better than Wilkinson's equation and the designers are forced to use purely empirical Nysmith (1969) or semiempirical equations developed by Cour-Palais in 1969. The Cour-Palais equations were later modified empirically in 1989. The purpose of the present investigation is to examine the many assumptions of the Wilkinson equation. An attempt is made to present design charts based on the modified-Wilkinson equation so that the designer can get a feel of the ranges of the parameters which are of interest and discard a huge range of parameters, thus, significantly reducing the number of test shots required. The analysis is based on a solution of the governing nonlinear differential equations for a plate, assuming axisymmetric behavior using polar coordinates.

Hui, David↗

NASA NTRS2017

Titan Atmospheric Entry Radiative Heating

Detailed spectrally and spatially resolved radiance has been measured in the Electric Arc Shock Tube for conditions relevant to Titan entry, varying atmospheric composition, free-stream density (equivalent to altitude) and shock velocity. Permutations in atmospheric composition include 1.1, 2, 5 and 8.6 CH4 by mole with a balance of N2 and 1.5 CH4 0.5 Ar 98 N2 by mole, which is consistent with the current understanding of Titan's atmosphere. The effect of gas impurities identified in previous shock tube studies were also examined by testing in pure N2 and deliberate addition of air to the CH4N2 mixtures. The test campaign measured radiation at velocities from 4.7 kms to 8 kms and free-stream pressures from 0.1 to 0.47 Torr. These conditions cover a range of potential trajectories for flight missions, including a direct ballistic trajectory, a fly by or an extremely high speed entry. Radiances measured in this work are substantially larger compared to that reported both in past EAST test campaigns and other shock tube facilities. Depending on the metric used for comparison, the discrepancy can be as high as an order of magnitude. Potential causes for the discrepancy, such as the effect of oxygen due to Air leakage, gas composition and purity are discussed. The present work provides a new benchmark set of data to replace those published in previous studies.

Earth↗

NASA NTRS2017

Titan Atmospheric Entry Radiative Heating

Detailed spectrally and spatially resolved radiance has been measured in the Electric Arc Shock Tube for conditions relevant to Titan entry, varying atmospheric composition, free-stream density (equivalent to altitude) and shock velocity. Permutations in atmospheric composition include 1.1, 2, 5 and 8.6 CH4 by mole with a balance of N2 and 1.5 CH4 0.5 Ar 98 N2 by mole, which is consistent with the current understanding of Titan's atmosphere. The effect of gas impurities identified in previous shock tube studies were also examined by testing in pure N2 and deliberate addition of air to the CH4N2 mixtures. The test campaign measured radiation at velocities from 4.7 kms to 8 kms and free-stream pressures from 0.1 to 0.47 Torr. These conditions cover a range of potential trajectories for flight missions, including a direct ballistic trajectory, a fly by or an extremely high speed entry. Radiances measured in this work are substantially larger compared to that reported both in past EAST test campaigns and other shock tube facilities. Depending on the metric used for comparison, the discrepancy can be as high as an order of magnitude. Potential causes for the discrepancy, such as the effect of oxygen due to Air leakage, gas composition and purity are discussed. The present work provides a new benchmark set of data to replace those published in previous studies.

Brandis, A. M↗

DOE OSTI2022

Polyimide aerogels for ballistic impact protection

The ballistic performance of edge-clamped monolithic polyimide aerogel blocks (12 mm thickness) has been studied through a series of impact tests using a helium-filled gas gun connected to a vacuum chamber and a spherical steel projectile (approximately 3 mm diameter) with an impact velocity range of 150–1300 m s -1 . The aerogels had an average bulk density of 0.17 g cm -3 with high porosity of approximately 88%. The ballistic limit velocity of the aerogels was estimated to be in the range of 175–179 m s -1 . Moreover, the aerogels showed a robust ballistic energy absorption performance (e.g., at the impact velocity of 1283 m s -1 at least 18% of the impact energy was absorbed). At low impact velocities, the aerogels failed by ductile hole enlargement followed by a tensile failure. By contrast, at high impact velocities, the aerogels failed through an adiabatic shearing process. Given the substantially robust ballistic performance, the polyimide aerogels have a potential to combat multiple constraints such as cost, weight, and volume restrictions in aeronautical and aerospace applications with high blast resistance and ballistic performance requirements such as in stuffed Whipple shields for orbital debris containment application.

42 ENGINEERING↗

NASA NTRS2004

Nickel-coated Aluminum Particles: A Promising Fuel for Mars Missions

Combustion of metals in carbon dioxide is a promising source of energy for propulsion on Mars. This approach is based on the ability of some metals (e.g. Mg, Al) to burn in CO2 atmosphere and suggests use of the Martian carbon dioxide as an oxidizer in jet or rocket engines. Analysis shows that CO2/metal propulsion will reduce significantly the mass of propellant transported from Earth for long-range mobility on Mars and sample return missions. Recent calculations for the near-term missions indicate that a 200-kg ballistic hopper with CO2/metal rocket engines and a CO2 acquisition unit can perform 10-15 flights on Mars with the total range of 10-15 km, i.e. fulfill the exploration program typically assigned for a rover. Magnesium is currently recognized as a candidate fuel for such engines owing to easy ignition and fast burning in CO2. Aluminum may be more advantageous if a method for reducing its ignition temperature is found. Coating it by nickel is one such method. It is known that a thin nickel layer of nickel on the surface of aluminum particles can prevent their agglomeration and simultaneously facilitate their ignition, thus increasing the efficiency of aluminized propellants.

Shafirovich, Evgeny↗

NASA NTRS2004

Nickel-Coated Aluminum Particles: A Promising Fuel for Mars Missions

Combustion of metals in carbon dioxide is a promising source of energy for propulsion on Mars. This approach is based on the ability of some metals (e.g. Mg, Al) to burn in CO2 atmosphere and suggests use of the Martian carbon dioxide as an oxidizer in jet or rocket engines. Analysis shows that CO2/metal propulsion will reduce significantly the mass of propellant transported from Earth for long-range mobility on Mars and sample return missions. Recent calculations for the near-term missions indicate that a 200-kg ballistic hopper with CO2/metal rocket engines and a CO2 acquisition unit can perform 10-15 flights on Mars with the total range of 10-15 km, i.e. fulfill the exploration program typically assigned for a rover. Magnesium is currently recognized as a candidate fuel for such engines owing to easy ignition and fast burning in CO2. Aluminum may be more advantageous if a method for reducing its ignition temperature is found. Coating it by nickel is one such method. It is known that a thin nickel layer of nickel on the surface of aluminum particles can prevent their agglomeration and simultaneously facilitate their ignition, thus increasing the efficiency of aluminized propellants. Combustion of single Ni-coated Al particles in different gas environments (O2, CO2, air) was studied using electrodynamic levitation and laser ignition. It was shown that the combustion mechanisms depend on the ambient atmosphere. Combustion in CO2 is characterized by the smaller size and lower brightness of flame than in O2, and by phenomena such as micro-flashes and fragment ejection. The size and brightness of flame gradually decrease as the particle burns.

Shafirovich, Evgeny↗