Search NASA⌕ Search

SEARCH · Search NASA

Results for “Carrier diffusions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2024

Coupled Gel/Seeded Growth of Cs2AgBiBr6 Single Crystals for Radiation Detection

Abstract— The all-inorganic lead free Cs2AgBiBr6 perovskite represents a highly promising environment-friendly radiation detector material. The first attempt to grow Cs2AgBiBr6 single crystals using the unique gel growth method is reported in this study. This technique enables controlled reagent diffusion in a gel medium at room temperature, fostering the growth of visible single crystals. It offers advantages over conventional methods, leading to fewer equilibrium and non-equilibrium defects and simplified execution. Interestingly, the as-grown crystals exhibited variations in size and colors within the gel matrix, indicating the influence of Bi solutes in Bi-poor and Bi-rich Cs2AgBiBr6 crystals. Once the crystals were confirmed by powder xray diffraction, a series of comprehensive material characterizations was performed. The resistivity of Cs2AgBiBr6 single crystals was measured at 1.12x107 Ω•cm. Trap density analysis yielded a value of 2.82 x1010 cm-3. The charge carrier mobility was determined to be 32.9 cm2V-1S-1, suggesting the suitability for radiation detector applications. Additional growth optimization is going on and further characterization will be reported during the presentation. Our work helps accelerate the development of lead-free perovskite materials toward radiation detector applications.

James, Ralph B.↗
DOE OSTI2025

A Comparison of Electronic Structure Methods for Predicting the Hydrogenation Energies of Candidate Molecules for Hydrogen Storage

The development of novel energy materials and fuels is required to expand current available energy sources. Aiming to reach this goal, there is growing interest in using molecular hydrogen as an energy carrier due to its abundance and high energy density. Liquid organic hydrogen carriers (LOHCs) are a promising route to the large-scale storage and transport of hydrogen for use in the energy economy. The search for thermodynamically viable LOHC molecules for real world use has led to a set of constraints on the dehydrogenation enthalpy and the minimum gravimetric hydrogen capacity. These constraints allow one to formulate the search for an ideal LOHC candidate molecule as an optimization problem well suited to the strengths of machine learning and artificial intelligence computational approaches. A critical barrier to a large-scale, high-throughput screening of LOHC candidate molecules is the lack of reliable training data. Computational electronic structure methods including density functional theory, coupled cluster approximations, and diffusion Monte Carlo can be used to provide training data where experimental data are either unreliable or do not exist. In this work, we use these methods to calculate the dehydrogenation energies and enthalpies of candidate LOHC molecules.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Direct Visualization of Current-Stimulated Oxygen Migration in YBa 2 Cu 3 O 7–δ Thin Films

The past years have witnessed major advancements in all-electrical doping control on cuprates. In the vast majority of cases, the tuning of charge carrier density has been achieved via electric field effect by means of either a ferroelectric polarization or using a dielectric or electrolyte gating. Unfortunately, these approaches are constrained to rather thin superconducting layers and require large electric fields in order to ensure sizable carrier modulations. In this work, we focus on the investigation of oxygen doping in an extended region through current-stimulated oxygen migration in YBa 2 Cu 3 O 7–δ superconducting bridges. The underlying methodology is rather simple and avoids sophisticated nanofabrication process steps and complex electronics. Here, a patterned multiterminal transport bridge configuration allows us to electrically assess the directional counterflow of oxygen atoms and vacancies. Importantly, the emerging propagating front of current-dependent doping δ is probed in situ by optical microscopy and scanning electron microscopy. The resulting imaging techniques, together with photoinduced conductivity and Raman scattering investigations, reveal an inhomogeneous oxygen vacancy distribution with a controllable propagation speed permitting us to estimate the oxygen diffusivity. These findings provide direct evidence that the microscopic mechanism at play in electrical doping of cuprates involves diffusion of oxygen atoms with the applied current. The resulting fine control of the oxygen content would permit a systematic study of complex phase diagrams and the design of electrically addressable devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Structural measurement of electron-phonon coupling and electronic thermal transport across a metal-semiconductor interface

Scattering of energetic charge carriers and their coupling to lattice vibrations (phonons) in dielectric materials and semiconductors are crucial processes that determine the functional limits of optoelectronics, photovoltaics, and photocatalysts. The strength of these energy exchanges is often described by the electron-phonon coupling coefficient, which is difficult to measure due to the microscopic time- and length-scales involved. In the present study, we propose an alternate means to quantify the coupling parameter along with thermal boundary resistance and electron conductivity by performing a high angular-resolution time-resolved X-ray diffraction measurement of propagating lattice deformation following laser excitation of a nanoscale, polycrystalline metal film on a semiconductor substrate. Our data present direct experimental evidence for identifying the ballistic and diffusive transport components occurring at the interface, where only the latter participates in thermal diffusion. This approach provides a robust measurement that can be applied to investigate microscopic energy transport in various solid-state materials.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Low-temperature and effective ex situ group V doping for efficient polycrystalline CdSeTe solar cells

CdTe solar cell technology is one of the lowest-cost methods of generating electricity in the solar industry, benefiting from fast CdTe absorber deposition, CdCl 2 treatment and Cu doping. However, Cu doping has low photovoltage and issues with instability. Doping group V elements into CdTe is therefore a promising route to address these challenges. Although high-temperature in situ group V doped CdSeTe devices have demonstrated efficiencies exceeding 20%, they face obstacles including post-deposition doping activation processes, short carrier lifetimes and low activation ratios. Here, we demonstrate low-temperature and effective ex situ group V doping for CdSeTe solar cells using group V chlorides. For AsCl 3 doped CdSeTe solar cells, the dopant activation ratio can be 5.88%, hole densities reach >2 × 10 15 cm -3 and carrier lifetime is longer than 20 ns. Thus, ex situ As doped CdSeTe solar cells show open-circuit voltages ~863 mV, compared to the highest open-circuit voltage of 852 mV for Cu doped CdSeTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2023

Disentangling the evolution of electrons and holes in photoexcited ZnO nanoparticles

The evolution of charge carriers in photoexcited room temperature ZnO nanoparticles in solution is investigated using ultrafast ultraviolet photoluminescence spectroscopy, ultrafast Zn K-edge absorption spectroscopy, and ab initio molecular dynamics (MD) simulations. The photoluminescence is excited at 4.66 eV, well above the band edge, and shows that electron cooling in the conduction band and exciton formation occur in <500 fs, in excellent agreement with theoretical predictions. The x-ray absorption measurements, obtained upon excitation close to the band edge at 3.49 eV, are sensitive to the migration and trapping of holes. They reveal that the 2 ps transient largely reproduces the previously reported transient obtained at 100 ps time delay in synchrotron studies. In addition, the x-ray absorption signal is found to rise in ∼1.4 ps, which we attribute to the diffusion of holes through the lattice prior to their trapping at singly charged oxygen vacancies. Indeed, the MD simulations show that impulsive trapping of holes induces an ultrafast expansion of the cage of Zn atoms in <200 fs, followed by an oscillatory response at a frequency of ∼100 cm−1, which corresponds to a phonon mode of the system involving the Zn sub-lattice.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

Atomistic Simulations for Thermophysical Properties of Uranium-Containing Halide Molten Salts

Characterizing the thermophysical properties in both fuel and coolant salts are critical in modeling, developing, process optimizing and utilizing molten salt reactors (MSRs), as these properties directly relate to operation metrics and can inform on the selection of candidate salts. The demand for consistent, accurate and publicly available thermophysical property data has become more apparent in recent years as interests have increased from molten salt reactor developers. There are a number of challenges in experimentally measuring properties such as thermal conductivity, viscosity, density and heat capacity , which have led to sparse and often times conflicting data points or molten salts in general. Additionally, there are a number of hazards to consider when synthesizing, storing, using, treating and disposing of molten salts. With the advances in computational capabilities over the last 10 years, the use of atomistic simulations can be implemented to support these efforts. The primary objective of this work is characterize the thermophysical transport properties in a number of molten chloride salts, and in particular NaCl-UCl 3 using ab-initio molecular dynamic (AIMD) simulations. In this binary salt the UCl 3 acts as the primary fissile material and NaCl acts as a carrier salt due with its’ high solubility for actinides A number of studies on the thermophysical properties of NaCl-UCl 3 have been published but there is not a vast amount of viscosity data for this system. In 1975, Desyatnik, et al published a study reporting dynamic viscosities that were calculated from kinematic viscosity measurements, and using the coefficients provided the viscosity in a 70:30 NaCl:UCl 3 mixture is 2.29 cP and 2.88 for a 60:40 mixture. Termini et al. recently reported viscosities in the range of 2.75 – 3 cP for the 63:37 NaCl-UCl 3 mixture in the same temperature range using rolling ball viscosity measurements. Computational viscosity of a similar mixture (64:36) can be obtained from the work Andersson et al. using the reported diffusion coefficients, and the hydrodynamic radius from the pair-radial distribution functions (RDFs). Using Eq (1) (vida infra), the viscosity would be 2.50 cP at 1100K. This is not to say that these values are incorrect due to the varying reported values, but aims to highlight the necessity of this work. The data reported in this ongoing work are computations on a 64:36 mixture of NaCl-UCl 3 at 987K. This work is likely to be expanded into varying concentrations of this mixture along with the inclusion of other salt candidate mixtures.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2025

Self-Trapped-Exciton Radiative Recombination in β–Ga 2 O 3 : Impact of Two Concurrent Nonradiative Auger Processes

The peculiarities of radiative and nonradiative processes associated with self-trapped intrinsic eXcitons in the excited β-Ga 2 O 3 crystals are studied via time-resolved techniques of induced absorption, transient grating, and photoluminescence (PL) at room temperature. The excitation above the bandgap is produced by laser pulses with linear light polarization parallel and orthogonal in the (–201) and (001) planes. We elucidate that the nonradiative recombination rate occurring in the eXciton prevails over its radiative emission rate in a wide range of free carrier concentration composed of excited and equilibrium electrons. Hence, the nonradiative recombination has no effect on the strong anisotropy and the shape of the eXciton emission band. However, we find out that the conventional ABC model of electron effective lifetime is insufficient for explanation of the excitation dependences. Inclusion of two nonradiative Auger mechanisms in a modified ABC formula provides excellent agreement of these dependences. We conclude that the trap-assisted Auger process is in proportion to the free electron density with coefficient B = 1.1 × 10 –11 cm 3 /s and appears at low/intermediate excitation, while the triple-particle Auger process is in proportion to Δn 2 with coefficient C = 8 × 10 –30 cm 6 /s and appears at high excitation conditions. The transition between two Auger mechanisms is accompanied by a rise of the eXciton diffusivity in preferred crystallographic directions where the radiative PL intensity is maximal. The diffusion length LD in these directions can reach values ~300 nm, but, at high excitations, LD becomes limited by Auger lifetimes. These findings pave the way for the implementation of self-trapped eXcitons into specific optoelectronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Improving the bulk gas transport of Fe-N-C platinum group metal-free nanofiber electrodes via electrospinning for fuel cell applications

To overcome transport limitations associated with thicker platinum group metal-free (PGM-free) electrodes, it's essential to investigate and tailor alternative electrode architectures to maximize the bulk electrode transport properties, whilst not significantly impeding electrocatalyst active site accessibility and electrode proton resistance. In this work, PGM-free nanofiber electrode mats, prepared by electrospinning a mixture of pyrolyzed Fe-N-C catalyst, Nafion ionomer and a carrier polymer Poly Acrylic acid (PAA), were compared to traditionally prepared electrodes. The morphological properties and elemental distribution of the fabricated nanofiber electrodes showed that the exterior surface of the PGM-free nanofibers was conformally covered with a thin ionomer film. Electrochemical diagnostics performed utilizing cyclic voltammetry, electrochemical impedance spectroscopy (EIS) and H 2 -limiting current measurements, revealed an increase in electric double layer capacitance, reduction in electrode proton transport and a significant improvement in bulk-electrode gas transport properties for the nanofiber electrodes, supporting the observed performance increase from electrochemical polarization data obtained in H 2 -O 2 /Air fuel cells. At 100% RH in H2/Air, the power density of the nanofiber electrodes increased ca. 50% vs. the traditionally prepared electrodes (ca. 260 vs 175 mW cm -2 ), which was attributed to a less tortuous molecular diffusion pathway and an associated reduction in the pressure dependent and independent gas transport resistances in the nanofiber electrodes.

25 ENERGY STORAGE↗
DOE OSTI2022

Nanoscale Hybrid Electrolytes with Viscosity Controlled Using Ionic Stimulus for Electrochemical Energy Conversion and Storage

As renewable energy is rapidly integrated into the grid, the challenge has become storing intermittent renewable electricity. Technologies including flow batteries and CO 2 conversion to dense energy carriers are promising storage options for renewable electricity. To achieve this technological advancement, the development of next generation electrolyte materials that can increase the energy density of flow batteries and combine CO 2 capture and conversion is desired. Liquidlike nanoparticle organic hybrid materials (NOHMs) composed of an inorganic core with a tethered polymeric canopy (e.g., polyetheramine (HPE)) have a capability to bind chemical species of interest including CO 2 and redox-active species. In this study, the unique response of NOHM-I-HPE-based electrolytes to salt addition was investigated, including the effects on solution viscosity and structural configurations of the polymeric canopy, impacting transport behaviors. The addition of 0.1 M NaCl drastically lowered the viscosity of NOHM-based electrolytes by up to 90%, reduced the hydrodynamic diameter of NOHM-I-HPE, and increased its self-diffusion coefficient, while the ionic strength did not alter the behaviors of untethered HPE. This study is the first to fundamentally discern the changes in polymer configurations of NOHMs induced by salt addition and provides a comprehensive understanding of the effect of ionic stimulus on their bulk transport properties and local dynamics. These insights could be ultimately employed to tailor transport properties for a range of electrochemical applications.

25 ENERGY STORAGE↗
DOE OSTI2022

Predicting Solar Cell Performance from Terahertz and Microwave Spectroscopy

Abstract Mobilities and lifetimes of photogenerated charge carriers are core properties of photovoltaic materials and can both be characterized by contactless terahertz or microwave measurements. Here, the expertise from fifteen laboratories is combined to quantitatively model the current‐voltage characteristics of a solar cell from such measurements. To this end, the impact of measurement conditions, alternate interpretations, and experimental inter‐laboratory variations are discussed using a (Cs,FA,MA)Pb(I,Br) 3 halide perovskite thin‐film as a case study. At 1 sun equivalent excitation, neither transport nor recombination is significantly affected by exciton formation or trapping. Terahertz, microwave, and photoluminescence transients for the neat material yield consistent effective lifetimes implying a resistance‐free JV‐curve with a potential power conversion efficiency of 24.6 %. For grainsizes above ≈20 nm, intra‐grain charge transport is characterized by terahertz sum mobilities of ≈32 cm 2 V −1 s −1 . Drift‐diffusion simulations indicate that these intra‐grain mobilities can slightly reduce the fill factor of perovskite solar cells to 0.82, in accordance with the best‐realized devices in the literature. Beyond perovskites, this work can guide a highly predictive characterization of any emerging semiconductor for photovoltaic or photoelectrochemical energy conversion. A best practice for the interpretation of terahertz and microwave measurements on photovoltaic materials is presented.

14 SOLAR ENERGY↗
DOE OSTI2025

Structural properties and recrystallization effects in ion beam modified B20-type FeGe films

Disordered iron germanium (FeGe) has recently garnered interest as a testbed for a variety of magnetic phenomena as well as for use in magnetic memory and logic applications. This is partially owing to its ability to host skyrmions and antiskyrmions—nanoscale whirlpools of magnetic moments that could serve as information carriers in spintronic devices. In particular, a tunable skyrmion–antiskyrmion system may be created through precise control of the defect landscape in B20-phase FeGe, motivating the development of methods to systematically tune disorder in this material and understand the ensuing structural properties. To this end, we investigate a route for modifying magnetic properties in FeGe. In particular, we irradiate epitaxial B20-phase FeGe films with 2.8 MeV Au 4+ ions, which creates a dispersion of amorphized regions that may preferentially host antiskyrmions at densities controlled by the irradiation fluence. To further tune the disorder landscape, we conduct a systematic electron diffraction study with in situ annealing, demonstrating the ability to recrystallize controllable fractions of the material at temperatures ranging from ~150 to 250°C. Finally, we describe the crystallization kinetics using the Johnson–Mehl–Avrami–Kolmogorov model, finding that the growth of crystalline grains is consistent with diffusion-controlled one-to-two dimensional growth with a decreasing nucleation rate.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The role of water vapor during the synthesis of hydrogen doped In 2 O 3

Hydrogen-doped In 2 O 3 synthesized using magnetron sputtering or atomic layer deposition in the presence of water vapor has high transparency in the near infra-red region and mobility values that are almost three to four times of those in commercially used In 2 O 3 :Sn at a much lower carrier concentration. However, simple questions like what happens when water molecules enter In 2 O 3 or why the dominant charge carrier changes from an oxygen vacancy in In 2 O 3 :Sn to H + in In 2 O 3 are not clear. Using hybrid functional based density functional theory calculations, in this study we show that water molecules spontaneously split into H + and OH – . The H + interstitial bonds with an oxygen in In 2 O 3 , and the OH – interstitial occupies a vacant lattice site or is trapped by an oxygen vacancy. Thus, in agreement with experimental findings, our results suggest that the concentration of oxygen vacancies decreases as the partial pressure of water increases. The charge transition level, ϵ ( – / + ) , of a hydrogen interstitial and the Fermi level at which the formation energies of OH – and H + are equal lie above the conduction band minimum, suggesting that the H + interstitial has a lower formation energy. In addition, water molecules do not exhibit any propensity to form clusters, meaning that H + ions can diffuse and remain spatially separated from each other.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Tailoring Charge Transport and Magnetism in Complex Half-Heusler/Full-Heusler Nanocomposites (Final Report)

This project exploits (1) the facile co-crystallization of the half-Heusler (HH) and full-Heusler (FH) structures, (2) the high coherency and stability of the HH/FH interfaces, and (3) the solid-state inter-conversion between HH and FH structures through local atomic diffusion, to investigate, for selected compositions of the HH and FH phases, the effect of size, dimensionality, dispersion and volume fraction of FH nanostructures on the electronic, phonon and magnetic behavior of the resulting HH/FH nanocomposites. Our goal is to identify and control key material and growth parameters governing phase formation, microstructural evolution, and to understand the mechanism by which these changes of the internal structure modify the material’s performance. To elucidate the mechanism by which the FH nanostructures regulate electronic charge transport and induce ferromagnetism within non-magnetic and magnetic semiconducting HH matrices, suitable series of HH/0D-FH and HH/2D-FH nanocomposites will be fabricated using synthesis conditions suggested by theoretical calculations of the formation energy and stability of various FH phases (varying M) in HH matrices with known chemical composition. The structure of the HH/FH interfaces (size, chemical composition, volume fraction and dispersion) will be investigated along with the evaluation of the electronic (carrier density, mobility, thermopower, electrical conductivity, effective mass), thermal and magnetic (susceptibility, magnetization etc.) properties of the resulting HH/FH nanocomposites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Probing the state of hydrogen in δ − AlOOH at mantle conditions with machine learning potential

Hydrous and nominally anhydrous minerals are a fundamental class of solids of enormous significance to geophysics. They are the water carriers in the deep geological water cycle and impact structural, elastic, plastic, and thermodynamic properties and phase relations in Earth's forming aggregates (rocks). They play a critical role in the geochemical and geophysical processes that shape the planet. Their complexity has prevented predictive calculations of their properties, but progress in materials simulations ushered by machine-learning potentials is transforming this state of affairs. Here, we adopt a hybrid approach that combines deep learning potentials (DPs) with the strongly constrained and appropriately normed meta-generalized gradient approximation functional to simulate a prototypical hydrous system. We illustrate the success of this approach to simulate δ − AlOOH ( δ ) , a phase capable of transporting water down to near the core-mantle boundary of the Earth ( ∼ 2900 km depth and ∼ 135 GPa ) in subducting slabs. A high-throughput sampling of phase space using molecular dynamics simulations with DPs sheds light on the hydrogen-bond behavior and proton diffusion at geophysical conditions. These simulations provide a pathway for a deeper understanding of these crucial components that shape Earth's internal state. Published by the American Physical Society 2024

Luo, Chenxing (ORCID:0000000341166851)↗
DOE OSTI2020

Excited Carrier Dynamics in a Dye-Sensitized Niobate Nanosheet Photocatalyst for Visible-Light Hydrogen Evolution

Dye-sensitized photocatalysts that consist of a light-absorbing dye and a wide gap oxide semiconductor have been studied extensively as components of solar energy conversion systems. Although surface modification by a metal and/or metal oxide has a significant impact on the photocatalytic efficiency, the mechanism by which these modifications increase the activity has not been fully understood. Here a dye-sensitized H 2 evolution system was constructed by using Pt-intercalated HCa 2 Nb 3 O 10 nanosheets, Ru(II) complex photosensitizers ([Ru(4,4’-(CH 3 ) 2- bpy) 2 (4,4’-(PO 3 H 2 ) 2- bpy)] 2+ and [Ru(4,4’-(CH 3 ) 2- bpy) 2 (4,4’-(CH 2 PO 3 H 2 ) 2- bpy)] 2+ , abbreviated as RuP 2+ and RuCP 2+ ; bpy = 2,2'-bipyridine), and amorphous Al 2 O 3 as building blocks. In the presence of iodide as the electron donor, the H 2 evolution rate from Pt/HCa 2 Nb 3 O 10 nanosheets sensitized by RuP 2+ was increased by modification of the nanosheets with Al 2 O 3 . On the other hand, Al 2 O 3 had a negative impact on the H 2 evolution rate when RuCP 2+ was employed. These hybrid materials were studied by transient diffuse reflectance spectroscopy and steady-state emission spectroscopy. A detailed analysis of the transient absorption profiles of the adsorbed Ru(II) complexes revealed that there are at least three states of the complexes on the nanosheet surface. The transient bleaching of the ground state absorbance had different lifetime components ranging from a few μs to several hundred μs, which mainly reflect back electron transfer rates from HCa 2 Nb 3 O 10 to the oxidized Ru(II) complexes. Here, the Al 2 O 3 modifier could inhibit not only the back electron transfer events but also electron injection from the excited state photosensitizer. Interestingly, the negative effect of Al 2 O 3 on the electron injection rate was negligible in the case of RuP 2+ , which also had a higher H 2 evolution rate. This work highlights that suppressing fast back electron transfer from Pt/HCa 2 Nb 3 O 10 to the oxidized Ru(II) complex, which occurs on a time scale of a few μs, and maximizing the electron injection efficiency are both necessary for improving dye-sensitized H 2 evolution.

14 SOLAR ENERGY↗
DOE OSTI2022

UV‐induced degradation of high‐efficiency silicon PV modules with different cell architectures

Abstract Degradation from ultraviolet (UV) radiation has become prevalent in the front of solar cells due to the introduction of UV‐transmitting encapsulants in photovoltaic (PV) module construction. Here, we examine UV‐induced degradation (UVID) in various commercial, unencapsulated crystalline silicon cell technologies, including bifacial silicon heterojunction (HJ), interdigitated back contact (IBC), passivated emitter and rear contact (PERC), and passivated emitter rear totally diffused (PERT) solar cells. We performed UV exposure tests using UVA‐340 fluorescent lamps at 1.24 W·m −2 (at 340 nm) and 45°C through 4.02 MJ·m −2 (2000 h). Our results showed that modern cell architectures are more vulnerable to UVID, leading to a significant power decrease (−3.6% on average; −11.8% maximum) compared with the conventional aluminum back surface field (Al‐BSF) cells (<−1% on average). The power degradation is largely caused by the decrease in short‐circuit current and open‐circuit voltage. A greater power decrease is observed in bifacial cells with rear‐side exposure compared with those with front‐side exposure, indicating that the rear side is more susceptible to UV damage. Secondary ion mass spectroscopy (SIMS) confirmed an increase in hydrogen concentration near the Si/passivation interface in HJ and IBC cells after UV exposure; the excess of hydrogen could result in hydrogen‐induced degradation and subsequently cause higher recombination losses. Additionally, surface oxidation and hot‐carrier damage were identified in PERT cells. Using a spectral‐based analysis, we obtained an acceleration factor of 5× between unpackaged cells (containing a silicon nitride antireflective coating on the front) in the UV test and an encapsulated module (with the front glass and encapsulant blocking 90% of the UV at 294 nm and 353 nm, respectively) in outdoor conditions. From the analytical calculations, we show that a UV‐blocking encapsulant can reduce UV transmission in the module by an additional factor of ~50.

14 SOLAR ENERGY↗