Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite fuels”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Flame tube parametric studies for control of fuel bound nitrogen using rich-lean two-stage combustion

An experimental parametric study of rich-lean two-stage combustion in a flame tube is described and approaches for minimizing the conversion of fuel-bound nitrogen to nitrogen oxides in a premixed, homogeneous combustion system are evaluated. Air at 672 K and 0.48 MPa was premixed with fuel blends of propane, toluene, and pyridine at primary equivalence ratios ranging from 0.5 to 2.0 and secondary equivalence ratios of 0.5 to 0.7. Distillates of SRC-II, a coal syncrude, were also tested. The blended fuels were proportioned to vary fuel hydrogen composition from 9.0 to 18.3 weight percent and fuel nitrogen composition from zero to 1.5 weight percent. Rich-lean combustion proved effective in reducing fuel nitrogen to NO sub x conversion; conversion rates up to 10 times lower than those normally produced by single-stage combustion were achieved. The optimum primary equivalence ratio, where the least NO sub x was produced and combustion efficiency was acceptable, shifted between 1.4 and 1.7 with changes in fuel nitrogen content and fuel hydrogen content. Increasing levels of fuel nitrogen content lowered the conversion rate, but not enough to avoid higher NO sub x emissions as fuel nitrogen increased.

Schultz, D. F.↗
DOE OSTI2020

Performance of Vehicle Fuel System Elastomers and Plastics with Test Fuels Representing Gasoline Blended with 10% Ethanol (E10) and 16% Isobutanol (iBu16)

The compatibilities of fuel system elastomers and plastics were evaluated for test fuels containing 16 vol.% isobutanol (iBu16) and 10 vol.% ethanol (E10). Elastomers included two fluorocarbons, four acrylonitrile butadiene rubbers (NBRs), and one type of fluorosilicone, neoprene, and epichlorohydrin/ethylene oxide. Plastic materials included four nylon grades, three polyamides, polytetrafluoroethylene (PTFE), polyvinylidene fluoride (PVDF), ethylene tetrafluoroethylene (ETFE), polyphenylene sulfide (PPS), high-density polyethylene (HDPE), polybutylene terephthalate (PBT), polyoxymethylene (POM), flexible polyvinylchloride (PVC), polyetherimide (PEI), polyetheretherketone (PEEK), and a phenol formaldehyde reinforced with glass fiber (GFPF). For each polymer material, the volume, mass, and hardness were measured before and after drying. Dynamic mechanical analysis (DMA) measurements were also performed on the dried specimens.For the elastomer materials the measured properties were similar for both fuels. The fluorocarbons and fluorosilicone swelled the least (~20%), while more moderate (20-45%) expansion occurred for the two NBR hose grades and (ECO). HNBR, neoprene, and silicone exhibited high swelling and softening, which likely precludes their use in many fuel systems. For the plastic materials, the observed swell was low; Nylon 11 swelled around 15%, but otherwise, their measured swell was <10%. Many of the plastics also showed sensitivity to alcohol type, as the E10 test fuel often imparted appreciably higher swell than iBu16. In general, the plastic materials showed good compatibility with the iBu16 and E10 test fuels. Here, the sole exception was the PVC material, which was structurally degraded from exposure to either fuel type. Compositional analysis showed high fuel retention in Nylon 12 and PVC. PVC also experienced a significant reduction in plasticizer compounds following exposure, which resulted in embrittlement and an increase in the glass-to-rubber transition temperature.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Developing Open-Source Tools for Increasing the Efficiency of Synthetic Aviation Turbine Fuel Certification Process

FuelLib is an open-source Python-based fuel library, developed by NREL, that leverages the group contribution method (GCM) of [1] to systematically estimate the thermodynamic and transport properties of hydrocarbon fuels. FuelLib predicts these properties based on the molecular structure of individual compounds or compound families, using weight percentages of a fuel's composition, typically measured using techniques such as gas chromatography (GC). FuelLib enables property estimation over a wide range of temperatures and pressures of multi-component fuels in the absence of detailed molecular composition data, making it particularly valuable for complex fuel mixtures where detailed experimental characterization of fuel composition is unavailable. These capabilities contribute directly to synthetic aviation turbine fuels (SATF) development, supporting the short-term American Society for Testing and Materials (ASTM) qualification of drop-in fuels while potentially expanding ASTM boundaries to certify a broader range of fuels.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2025

Multiscale Modeling of the Mechanical Response of Silicon Carbide Composite Within the Accelerated Fuel Qualification Framework

The accelerated fuel qualification (AFQ) framework has been used for the initial development of multiscale modeling of silicon carbide (SiC) fiber reinforced composite (SiC-SiC). The AFQ framework provides a methodology to leverage physics-informed multiscale modeling along with a reduced set of empirical test data to reduce the time and cost of licensing and qualification of new nuclear fuel systems while maintaining the overall nuclear power plant safety case. SiC-SiC is being proposed for in-core applications, most notably fuel cladding, for current and next-generation nuclear reactors because of its high temperature stability, irradiation tolerance, and ability to withstand many accident conditions. As these composites exhibit multiscale architectures and complex microstructure-based fracture mechanics, it is an appealing use case for the AFQ methodology. While the end goal of this work is a single multiscale model that can be used for predictive in-core performance, current focus is on the individual various length scale models. Four individual models have been initially developed from microscale to engineering system level to capture key physics-based effects across different length scales. These models include a microscale homogenized tow model, a mesoscale fast Fourier transform–based weave model that integrates the homogenized tow model, a mesoscale finite element–based weave model, and a system-level BISON fuel performance model. Results of these models have undergone an initial comparison with separate-effects test data showing a good match to experimental results. By using the AFQ framework during model development, several near-term benefits have been secured including a reduction in development time for the SiC-SiC cladding, more targeted irradiation testing, and a better understanding of uncertainty.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Preliminary Conceptual Design of Nuclear Thermal Rocket Reactor Cores Using Ceramic Fuels with Beryllium or Composite Neutron Moderators

Herein several preliminary conceptual designs of nuclear thermal rocket reactor cores are presented that use tin-bonded monolithic ceramic [mononitride (UN), monocarbide (UC), and uranium dioxide (UO 2 )] fuel plates or pins with molybdenum-tungsten alloy clad. Neutron moderation is provided by a block of Be metal or composite materials using metal hydrides such as ZrH 1.6 or YH 1.6 with different matrices (MgO or Be). Mainly high-assay low-enriched uranium is considered, but highly enriched uranium is also assessed for a few configurations. Nominal core thermal power is 300 MW corresponding to about 66 kN (15 klbf) of thrust, and with minimal modifications, 500 MW may be possible (25 klbf of thrust). Depending on the configurations, the amount of 235 U needed for criticality is 30 to 90 kg, and reactor weight is 2.5 to 3.8 tonnes.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

3Y-TZP Toughened and Oxidation-resistant U 3 Si 2 Composites for Accident Tolerant Fuels

In this work, we report an innovative approach synergizing multiple effects of microstructure control, oxide protection and phase transformation-induced mechanically toughening to develop advanced U 3 Si 2 fuels with state-of-the-art materials properties. 3Y-TZP (3 mol% yttria doped stabilized tetragonal zirconia) additives are incorporated and uniformly distributed into the SPS-densified U 3 Si 2 fuel matrix, enhancing materials fracture toughness up to 4.04 MPa m 1/2 . The 3Y-TZP incorporated U 3 Si 2 composite pellets show significantly improved onset temperature of oxidation above 560 °C, which can be further improved to 617 °C with 3 vol% addition by post-sintering thermal annealing. We report the development of mechanically tough and oxidation-resistant U 3 Si 2 with minimal additive represents a major step forward towards realizing the potential of high density U 3 Si 2 as the leading fuel concept to increase accidence tolerance of nuclear energy systems.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Grid-to-rod fretting wear study of SiC/SiC composite accident-tolerant fuel claddings using an autoclave fretting bench test

Grid-to-rod-fretting (GTRF) in pressurized water reactors (PWRs) is known to cause wear and surface damage on the fuel claddings, potentially leading to radioactive leakage. One of the accident-tolerant fuel (ATF) concepts is to use advanced cladding materials that could withstand higher temperatures. Here, we investigated the wear behavior of candidate silicon carbide (SiC)-based composite claddings with different levels of surface finish in fretting against a commercial ZIRLO alloy grid using a unique bench-scale autoclave GTRF rig. The experiments mimicked the environment in an industrial full-assembly PWR simulator. Fretting tests were conducted with a realistic load (~0.5 N) in deionized water under a pressure of 20–23 bar at 204 °C for 100 h. While the SiC/SiC composite claddings showed significantly higher wear resistance than the commercial ZIRLO alloy cladding as expected, the smoother versions experienced surprisingly higher wear than the much softer counterface, ZIRLO grid. The wear mechanism of the SiC/SiC cladding was attributed to the SiC wear debris that was trapped at the fretting interface causing both 3-body and 2-body (embedded into the grid surface) abrasion of the cladding. Rougher SiC/SiC claddings had less material loss but caused more wear on the ZIRLO grid. Finally, pre-oxidized ZIRLO grid showed better compatibility with the SiC/SiC cladding to protect both the cladding and grid as a result of reduced wear debris trapping.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coordinated Multiscale Modeling and Synthesis of Novel Nanostructured Composite Membranes for Solar Fuels Generation (Final Report)

Generation of carbon-based liquid fuels from reduction of CO 2 using solar energy requires the development of improved membranes that provide good ionic conductivity and mechanical properties while minimizing the crossover of gases and reduction products. Using closely coordinated multiscale modeling, synthesis and characterization studies we propose to investigate and develop novel nanostructured composite membranes with applications to conversion of carbon dioxide to storable chemical fuels. The envisioned proton exchange membranes (PEMs) will be based on a support of self- assembling polymer-modified nanoparticles with controllable porosity and tortuosity. The use of a nanoparticle support will provide control of transport and mechanical properties of the membranes. Tuning the copolymer modification of nanoparticles (polymer architectures, brush grafting density) will allow to optimize the ion (proton) transport via the Grotthuss mechanism through narrow hydrated channels while minimizing crossover of gases and reaction products due to the high density of the grafted brush and use of a non-ionic conducting glassy polymers to fill spaces between polymer-grafted nanoparticles. In Phase I synthesis of the copolymers and their attachment to the nanoparticle support will be guided by multiscale simulations that include atomistic molecular dynamics and continuum-level transport simulations. The former will include reactive and non-reactive atomistic simulations that will provide key insight into nanoscale polymer morphology and ion/molecular transport mechanisms need to optimize the copolymer structure. The latter will provide insight into the role of nanoparticle self-assembly on the global transport of ionic and molecular species. The proton conduction and CO 2 /methanol permeability of the membranes will be experimentally characterized as well as simulated and will be correlated with morphology and polymer structure. Prototypes of optimal membranes will be fabricated and characterized at the end of the project. Successful development of improved nanostructured composite PEMs and demonstration of the simulation-guided materials-by-design paradigm will result in our ability to design and synthesize membranes for a wide variety of solar fuels generation and related electrochemical applications.

14 SOLAR ENERGY↗
NASA NTRS1992

Ceramic matrix composite applications in advanced liquid fuel rocket engine turbomachinery

Fiber-reinforced ceramic matrix composites have been identified with properties suitable for near term applications. Conceptual design studies indicate the feasibility of applying C/SiC, and subelements were manufactured that verify selected fabrication features and key material properties. Tests and inspection of these subelements confirmed their capabilities.

Brockmeyer, Jerry W.↗
NASA NTRS1980

Response of the global climate to changes in atmospheric chemical composition due to fossil fuel burning

Recent modeling of atmospheric chemical processes (Logan et al, 1978; Hameed et al, 1979) suggests that tropospheric ozone and methane might significantly increase in the future as the result of increasing anthropogenic emissions of CO, NO(x), and CH4 due to fossil fuel burning. Since O3 and CH4 are both greenhouse gases, increases in their concentrations could augment global warming due to larger future amounts of atmospheric CO2. To test the possible climatic impact of changes in tropospheric chemical composition, a zonal energy-balance climate model has been combined with a vertically averaged tropospheric chemical model. The latter model includes all relevant chemical reactions which affect species derived from H2O, O2, CH4, and NO(x). The climate model correspondingly incorporates changes in the infrared heating of the surface-troposphere system resulting from chemically induced changes in tropospheric ozone and methane. This coupled climate-chemical model indicates that global climate is sensitive to changes in emissions of CO, NO(x) and CH4, and that future increases in these emissions could augment global warming due to increasing atmospheric CO2.

Hameed, S.↗
NASA NTRS1977

A study of the effects of long-term exposure to fuels and fluids on the behavior of advanced composite materials

The Task 1 (thirty-six-month) and Task 2 (twelve-month) exposure of composite materials to fuel and fluid environments are reported. Narmco T300/5209 (Task 1) shows no significant degradation. Slightly lower mechanical properties were obtained from fuel/water immersion exposure of this material. Kevlar 49/2544 (also Task 1) exhibits significant drop in short-beam shear when exposed to fuel/water immersion. Task 2 materials (T300/5208, Kevlar 49 fabric/5209, and Kevlar 49 fibers) have not shown any significant mechanical property degradation to date.

Hendricks, C. L.↗
NASA NTRS1991

Advanced materials for space nuclear power systems

The overall philosophy of the research was to develop and characterize new high temperature power conversion and radiator materials and to provide spacecraft designers with material selection options and design information. Research on three candidate materials (carbide strengthened niobium alloy PWC-11 for fuel cladding, graphite fiber reinforced copper matrix composites for heat rejection fins, and tungsten fiber reinforced niobium matrix composites for fuel containment and structural supports considered for space power system applications is discussed. Each of these types of materials offers unique advantages for space power applications.

Titran, Robert H.↗
NASA NTRS1991

Advanced materials for space nuclear power systems

The overall philosophy of the research was to develop and characterize new high temperature power conversion and radiator materials and to provide spacecraft designers with material selection options and design information. Research on three candidate materials (carbide strengthened niobium alloy PWC-11 for fuel cladding, graphite fiber reinforced copper matrix composites for heat rejection fins, and tungsten fiber reinforced niobium matrix composites for fuel containment and structural supports) considered for space power system applications is discussed. Each of these types of materials offers unique advantages for space power applications.

Titran, Robert H.↗
DOE OSTI2024

Performance Testing of a Moving-Bed Gasifier Using Coal, Biomass, and Waste Plastic Blends with Washed and Unwashed Legacy Coals and Other Waste Fuels to Generate White Hydrogen

The objective of this effort, primarily funded by the United States Department of Energy (DOE), and led by the Electric Power Research Institute, Inc. (EPRI), with support by Hamilton Maurer International (HMI) and Sotacarbo S.p.A. (Sotacarbo), has been to qualify coal, biomass, and plastic waste blends based on performance testing of selected fuel pellet compositions in a pilot-scale updraft moving-bed (UDMB) gasifier. The testing provided relevant data to advance the commercial-scale design of the moving-bed gasifier to be able to successfully use these feedstocks to produce hydrogen. In particular, the effects of waste plastics on feedstock development (i.e., blending and pelletizing) and the resulting products (i.e., syngas compositions, organic condensate production, and ash characteristics) are the focus. The gasifier used for testing is HMI’s moving-bed gasifier, which has been proven capable of gasifying nearly all coal ranks. It has also shown the ability in prior testing work to gasify wood chips (biomass). However, mixtures of these fuels with plastic wastes have not been prepared and gasified together. The three feedstocks were densified and pelletized by California Pellet Mill (CPM) to meet the feedstock size required by Sotacarbo’s 30mm ID UDMB gasifier, under contract to HMI. The technical tasks and results from this two-year research project included: (1) Feed Procurement and Preparation: Nine different tri-fuel pellets were prepared from varying compositions of fresh mined PRB coal, corn stover biomass, and car fluff waste plastics. Tri-fuel pellets were produced by CPM and shipped to Sotacarbo’s test facility in Carbonia, Sardinia, Italy. (2) Test Plan Development: A test plan was created to define the test runs to be performed. The test plan detailed the different UDMB gasification tests to be performed in Sotacarbo’s 12-inch ID pilot scale gasifier, the process monitoring instrumentation used, and the extractive samples recovered for analysis of the total gasification process mass and energy balance. (3) Gasifier Testing: Nine different gasification runs were performed in the pilot-scale gasifier at Sotacarbo using nine different fuel feedstock compositions generated from varying mixtures of PRB coal, biomass, and plastic wastes. The testing generated performance data on gasification reaction efficiency and performance, yielding relevant data for models used to scale up the gasifier design. This task also included work to refurbish and reassemble the pilot gasifier at Sotacarbo and perform a baseline 100% PRB coal run. (4) Data Analysis and Reporting: Review of the data, determination of figures of merit, and interpretation of the results are reported in the project’s final report, published in March 2024. The results show that all tri-fuel pellets gasified well and maintained structural integrity throughout the gasification process. The syngas generated can be shifted to hydrogen by using commercial syngas shifting technologies. (5) High Fidelity computational fluid dynamics (CFD) Simulation: The National Energy Technology Laboratory (NETL) team performed CFD simulations of the UDMB gasifier for two of the tri-fuel pellets gasified in Sotacarbo’s pilot scale gasifier. The kinetic mechanisms for the pyrolysis of each constituent, PRB coal, corn stover biomass, and waste plastics are based on thermogravimetric analysis performed by Sotacarbo. The gasification model was validated by comparing the predicted syngas composition at the exit of the gasifier with the measured syngas composition. In addition, the reactor’s measured internal temperature profile agreed well with the predicted internal reactor temperature profile. These results validate that the model can be used to predict the performance of the updraft moving bed gasifier for different feedstocks and operating conditions. This paper summarizes the results of the completed work in which the pelletizing procedure was validated to ensure the viability of the tri-fuel pellets for the gasification runs performed at Sotacarbo’s 30 mm UDMB gasifier. The gasification performance data from this series of nine runs will enable modeling of a full-scale HMI industrial scale gasifier supporting both combined heat and power, and Hydrogen production from coal (both fresh mined and legacy) combined with various biomass and waste plastics. Additionally, plans and progress on a follow-up project, being executed by the same project team, will be presented. In this project, a total of twenty (20) different feedstocks are being prepared from varying compositions of biomass (both woody biomass and corn stover) with a mixture of legacy coal waste, plastic waste, and refuse-derived fuel (RDF). The testing will provide information on gasification reaction efficiency/performance, yielding relevant data for models used to scale up the gasifier design to 50 megawatt electric (MWe) (equivalent hydrogen production). Tests will also be performed on a bench-scale fluidized-bed gasifier for comparison purposes. The results of this testing will be used to specify the range of feedstock blends that can be successfully gasified as well as quantify gasifier outputs based on specific blends.

08 HYDROGEN↗
NASA NTRS1983

Fuel containment and damage tolerance in large composite primary aircraft structures

Technical problems related to fuel containment and damage tolerance of composite material wings for transport aircraft was investigated. The major tasks are the following: (1) the preliminary design of damage tolerant wing surface using composite materials; (2) the evaluation of fuel sealing and lightning protection methods for a composite material wing; and (3) an experimental investigation of the damage tolerant characteristics of toughened resin graphite/epoxy materials. The design concepts investigated for the upper and lower surfaces of a composite wing for a transport aircraft are presented and the relationship between weight savings and the design allowable strain used within the analysis is discussed. Experiments which compare the fuel sealing characteristics of bolt-bonded joints and bolted joints sealed with a polysulphide sealant are reviewed. Data from lightning strike tests on stiffened and unstiffened graphite/epoxy panels are presented. A wide variety of coupon tests were conducted to evaluate the relative damage tolerance of toughened resin graphite/epoxies. Data from these tests are presented and their relevance to the wing surface design concepts are discussed.

Griffin, C. F.↗
NASA NTRS1985

Detailed studies of aviation fuel flowability

Six Jet A fuels, with varying compositions, were tested for low temperature flowability in a 190-liter simulator tank that modeled a section of a wing tank of a wide-body commercial airplane. The insulated tank was chilled by circulating coolant through the upper and lower surfaces. Flow-ability was determined as a function of fuel temperature by holdup, the fraction of unflowable fuel remaining in the tank after otherwise complete withdrawal. In static tests with subfreezing tank conditions, hold up varied with temperature and fuel composition. However, a general correlation of two or three classes of fuel type was obtained by plotting holdup as a function of the difference between freezing point and boundary-layer temperature, measured 0.6 cm above the bottom tank surface. Dynamic conditions of vibrations and slosh or rate of fuel withdrawal had very minor effects on holdup. Tests with cooling schedules to represent extreme, cold-day flights showed, at most, slight holdup for any combination of fuel type or dynamic conditions. Tests that superimposed external fuel heating and recirculation during the cooldown period indicates reduced hold up by modification of the low-temperature boundary layer. Fuel heating was just as effective when initiated during the later times of the tests as when applied continuously.

Mehta, H. K.↗