SEARCH · Search NASA

Results for “Critical zone”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

DOE OSTI2025

Deep Roots Supply Reactivity and Enhance Silicate Weathering in the Bedrock Vadose Zone

In upland environments, roots commonly extend deep below soil into partially saturated bedrock. This Bedrock Vadose Zone (BVZ) has been shown to store and circulate water, host organic carbon respiration and serve as a critical source of rock-derived nutrients. However, the extent to which deep roots influence chemical weathering rates remains poorly understood. Here, we report 4 years of depth-resolved major ion chemistry over a 16-m thick BVZ hosting a deep rhizosphere in a catchment subject to a Mediterranean climate. These data allow development and validation of a reactive transport model (RTM), revealing that the timescales of water storage and drainage in the BVZ are sufficient to facilitate substantial chemical weathering of the shale bedrock. However, observed solute concentrations are only reproduced by the RTM when we explicitly include measured rates of CO 2(g) production meters below soil driven by the deeply rooted forest. By combining direct observations and a process-based RTM we conclude that the carbon respiration promoted by deep roots significantly enhances chemical weathering rates in the BVZ, constituting 43% ± 3% of total solute flux from the base of the BVZ to the water table.

Osorio‐Leon, Ivan D. [University of Illinois Urban↗

DOE OSTI2022

United States Department of Energy Sandia Natinoal Laboratories, California Arroyo Seco Improvement Program (Annual Report for 2021)

The Arroyo Seco Improvement Program (ASIP) is intended to provide active channel improvements and stream zone management activities that will reduce current flood and erosion risk while providing additional and improved habitat for critical species that may use the Arroyo Seco at the United States Department of Energy (DOE), Sandia National Laboratories, California (SNL/CA) location. The objectives of the ASIP are: correct existing channel stability problems associated with existing arroyo structures (i.e. bridges, security grates, utility crossings, and drain structures), correct bank erosion and provide protection against future erosion, reduce the risk of future flooding, and provide habitat improvement and creation of a mitigation credit for site development and management activities.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2022

Arroyo Seco Improvement Project: Annual Report 2022

The Arroyo Seco Improvement Program (ASIP) is intended to provide active channel improvements and stream zone management activities that will reduce current flood and erosion risk while providing additional and improved habitat for critical species that may use the Arroyo Seco at the Sandia National Laboratories, California (SNL/CA). SNL/CA facility is operated by the National Technology and Engineering Solutions of Sandia, LLC (NTESS) under a contract with the U.S. Department of Energy/National Nuclear Security Administration (DOE/NNSA). The DOE/ NNSA’s Sandia Field Office (SFO) oversees the operations of the site.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2026

Data for Autonomous Transportation Awareness: Data Exchange Use Cases, Standards, and Barriers

This report examines the critical data exchanges between automated vehicle (AV) service providers and the cities and municipalities they serve. It assists municipal authorities in navigating the often complex and real-time digital data exchanges needed to support AV mobility services, with emphasis in three areas: (1) critical safety data for broad-area situational awareness of hazards typically associated emergency dispatch or roadway work zones; (2) performance metrics of AV services that inform the quantity, quality, spatial extents, and impact on the roadway network; and (3) regulatory and policy information, particularly dynamic information that governs how AV services interact with the roadway network, with emphasis on curb space. The report reviews existing practices and emerging protocols and standards and identifies key gaps to address moving forward.

33 ADVANCED PROPULSION SYSTEMS↗

DOE OSTI2025

On the Stability Analysis of Astrophysical Cooling Functions

To model the temperature evolution of optically thin astrophysical environments at MHD scales, radiative and collisional cooling rates are typically either pretabulated or fit into a functional form and then input into MHD codes as a radiative loss function. Thermal balance requires estimates of the analogous heating rates, which are harder to calculate, and due to uncertainties in the underlying dissipative heating processes these rates are often simply parameterized. The resulting net cooling function defines an equilibrium curve that varies with density and temperature. Such cooling functions can make the gas prone to thermal instability (TI), which will cause departures from equilibrium. There has been no systematic study of thermally unstable parameter space for nonequilibrium states. Motivated by our recent finding that there is a related linear instability, catastrophic cooling instability, that can dominate over TI, here we carry out such a study. We show that Balbus instability criteria for TI can be used to define a critical cooling rate, Λ c , that permits a nonequilibrium analysis of cooling functions through the mapping of TI zones. We furthermore illustrate how thermal conduction modifies the shape of TI zones. Upon applying a Λ c -based stability analysis to coronal loop simulations, we find that loops undergoing periodic episodes of coronal rain formation are linearly unstable to catastrophic cooling instability, while TI is stabilized by thermal conduction.

79 ASTRONOMY AND ASTROPHYSICS↗

NASA NTRS1982

The crack and wedging problem for an orthotropic strip

The plane elasticity problem for an orthotropic strip containing a crack parallel to its boundaries is considered. The problem is formulated under general mixed mode loading conditions. The stress intensity factors depend on two dimensionless orthotropic constants only. For the crack problem the results are given for a single crack and two collinear cracks. The calculated results show that of the two orthotropic constants the influence of the stiffness ratio on the stress intensity factors is much more significant than that of the shear parameter. The problem of loading the strip by a rigid rectangular lengths continuous contact is maintained along the wedge strip interface; at a certain critical wedge length the separation starts at the midsection of the wedge, and the length of the separation zone increases rapidly with increasing wedge length.

Cinar, A.↗

NASA NTRS1983

The crack and wedging problem for an orthotropic strip

Cinar, A.↗

NASA NTRS1985

Two-phase flows within systems with ambient pressure

In systems where the design inlet and outlet pressures are maintained above the thermodynamic critical pressure, it is often assumed that two phase flows within the system cannot occur. Designers rely on this simple rule of thumb to circumvent problems associated with a highly compressible two phase flow occurring within the supercritical pressure system along with the uncertainties in rotordynamics, load capacity, heat transfer, fluid mechanics, and thermophysical property variations. The simple rule of thumb is adequate in many low power designs but is inadequate for high performance turbomachines and linear systems, where two phase regions can exist even though outlet pressure is greater than critical pressure. Rotordynamic-fluid-mechanic restoring forces depend on momentum differences, and those for a two phase zone can differ significantly from those for a single-phase zone. Using the Reynolds equation the angular velocity, eccentricity, geometry, and ambient conditions are varied to determine the point of two phase flow incipience.

Hendricks, R. C.↗

NASA NTRS1986

Theory for computing the field scattered from a smooth inflected surface

A theory is described for computing the reflected or scattered field from a smooth body with inflection points. These inflections occur in certain directions at each surface point for which the total (Gaussian) curvature is zero or negative. For surface illumination in one of these critical directions, the usual reflection formulas obtained by the high-frequency approximation are inapplicable, and a shadow zone exists in the reflected field. Scattering into the shadow zone is treated, as well as specular reflection. This theory should have a variety of applications such as for certain optics problems, computer graphics modeling of three-dimensional shapes, and the design and analysis of specialized microwave reflector antennas.

Barger, R. L.↗

NASA NTRS1999

Characterization of the Heat Extraction Capability of a Compliant, Sliding, Thermal Interface for Use in a High Temperature, Vacuum Microgravity Furnace

Much of the material science gained in microgravity research requires processing a sample in a high performance furnace. One such furnace currently being designed is the Quench Module Insert (QMI). The Principle Investigators, for whom the furnace is proposed, require high temperature gradients in their cylindrical samples to achieve the science objectives. One of the components critical to achieving high sample axial temperature gradients in the Quench Module Insert is a high performance cold zone to extract the heat from the sample. This cold zone employs a compliant, sliding thermal interface based on a Vel-Therm felt. This felt provides a conductive path between the Sample Cartridge Assembly (SCA) exterior surface and the interior surface of the water cooled chill block while allowing movement of the sample relative to the chill block. The Vel-Therm felt is composed of long polymer-based fibers affixed to a thin flexible substrate layer. The fibers are oriented perpendicular to this substrate giving the felt the appearance of a velvet fabric. The Vel-Therm felt heat extraction capability was quantified in earlier tests performed in an inert gas environment. The current activity, described in this paper, is intended to characterize the extraction capability of Vel-Therm felt in a vacuum environment similar to the QMI environment. This testing is necessary to quantify the thermal performance of the Vel-Therm felt and the sensitivity of that performance to key variables. The data derived from these tests will be incorporated into the current thermal models to improve the quality of the models and reduce uncertainty of the analytical results. In addition, the data will be used to help select the appropriate Vel-Therm felt and set proper operating limits as well as assess the performance range of the furnace. The objective of this test is to measure the heat extraction rate of the Vel-Therm felt as specified by the effective heat transfer coefficient. Therefore, the test setup was designed to force the bulk of the heat transfer through the area where the Vel-Therm felt was applied. A heat source, consisting of a ceramic heating element encased in a Copper (Cu) housing is mounted on four isolated support rods. A 6-layer molybdenum radiation shield is used to insulate against heat loss from the heater and prevent heat exchange between the hot and cold sides of the test apparatus. The Vel-Therm felt is affixed to the surface of the cold sink, a water-cooled Cu chill block. An adjustable plate supports and isolates the cold sink from above and is used to control the amount of the deflection of the Vel- Therm when in contact with the Cu heating element housing. The primary means of establishing the power being conducted through the felt is to measure the energy being transferred to the water passing through the chill block. Analysis was performed to support the assumption that the source and sink surfaces were approximately isothermal under the specific test conditions. As a check on the amount of power passing through the felt, the power supplied to the heater was also measured. Thermocouples were strategically located throughout the test apparatus for measurement purposes. A bell jar was lowered over the assembly to impose vacuum conditions. Currently, variables tested have been fiber compression and fiber type and surface temperatures (both the hot and cold side temperatures are hypothesized to be important to the performance of the Vel-Therm.) Selected runs were repeated to ensure consistency and repeatability. Results obtained thus far reveal that Vel-Therm performance is significantly degraded by fibers being exposed to high compression. It also shows that performance is somewhat negatively impacted by previous compression, thereby, raising the question of repeatability. In addition, early results show a significant dependence on temperature. A computer aided mathematical analysis of the test setup is ongoing. The results will be correlated to actual results. The correlation will examine such details as parasitic loses, conduction down the power leads and many other concerns.

Bellomy-Ezell, Jenny↗

NASA NTRS2007

STS-114 Micrometeoroid/Orbital Debris (MMOD) Post-Flight Assessment

NASA Johnson Space Center (JSC) personnel assisted Kennedy Space Center (KSC) inspection teams in the identification of 41 micrometeoroid/orbital debris (MMOD) impact sites on the OV-103 vehicle (Discovery) during STS-114 postflight inspections. There were 14 MMOD impacts reported on the crew module windows (Figure 1). The largest impact feature, a 6.6 mm x 5.8 mm crater on window #4, was caused by a particle with an estimated diameter of 0.22 mm (Figure 2). This impact was among the largest ever recorded on a crew module window. The window was removed and replaced. Scanning Electron Microscope/Energy Dispersive X-ray (SEM/EDX) analysis of dental mold samples from the impact site to determine particle origin was inconclusive, possibly due to contamination picked up on the ferry flight from Edwards Air Force Base to KSC. The radiators on the inside of the payload bay doors sustained 19 impacts (Figure 3) with one of the impacts causing a face sheet perforation. The 0.61 mm diameter hole was produced by a particle with an estimated diameter of 0.4 mm, which approaches the 0.5-mm critical particle diameter of the wing leading edge reinforced carbon-carbon (RCC) panel high-temperature regions (Zone 3, Figure 4) that was established during Return to Flight testing of the RCC panels. An inspection of the payload bay door exterior insulation (FRSI) revealed a 5.8 mm x 4.5 mm defect that was caused by an MMOD particle with unknown composition, as the sample obtained was contaminated. Figure 5 provides a summary of the exterior surface survey that was conducted following the STS-114 mission. Two windows were removed and replaced due to hypervelocity impact. Nineteen impacts were recorded on the payload bay door radiators, with one face sheet penetration. Three impact sites were identified on the FRSI. There were four hypervelocity impact sites detected on the wing leading edge RCC panels. One impact was detected on the top cover of the TPS sample box (TSB) payload that was mounted on a carrier in the aft portion of the payload bay.

Hyde, J.↗

NASA NTRS2014

Integration of the Total Lightning Jump Algorithm into Current Operational Warning Environment Conceptual Models

The presence and rates of total lightning are both correlated to and physically dependent upon storm updraft strength, mixed phase precipitation volume and the size of the charging zone. The updraft modulates the ingredients necessary for electrification within a thunderstorm, while the updraft also plays a critical role in the development of severe and hazardous weather. Therefore utilizing this relationship, the monitoring of lightning rates and jumps provides an additional piece of information on the evolution of a thunderstorm, more often than not, at higher temporal resolution than current operational radar systems. This correlation is the basis for the total lightning jump algorithm that has been developed in recent years. Currently, the lightning jump algorithm is being tested in two separate but important efforts. Schultz et al. (2014; AMS 10th Satellite Symposium) is exploring the transition of the algorithm from its research based formulation to a fully objective algorithm that includes storm tracking, Geostationary Lightning Mapper (GLM) Proxy data and the lightning jump algorithm. Chronis et al. (2014; this conference) provides context for the transition to current operational forecasting using lightning mapping array based products. However, what remains is an end to end physical and dynamical basis for relating lightning rates to severe storm manifestation, so the forecaster has a reason beyond simple correlation to utilize the lightning jump algorithm within their severe storm conceptual models. Therefore, the physical basis for the lightning jump algorithm in relation to severe storm dynamics and microphysics is a key component that must be further explored. Many radar studies have examined flash rates and their relation to updraft strength, updraft volume, precipitation‐sized ice mass, etc.; however, relation specifically to lightning jumps is fragmented within the literature. Thus the goal of this study is to use multiple Doppler techniques to resolve the physical and dynamical storm characteristics specifically around the time of the lightning jump. This information will help forecasters anticipate lightning jump occurrence, or even be of use to determine future characteristics of a given storm (e.g., development of a mesocyclone, downdraft, or hail signature on radar), providing additional lead time/confidence in the severe storm warning paradigm.

Shultz, Christopher J.↗

NASA NTRS2014

Physical and Dynamical Linkages between Lightning Jumps and Storm Conceptual Models

The presence and rates of total lightning are both correlated to and physically dependent upon storm updraft strength, mixed phase precipitation volume and the size of the charging zone. The updraft modulates the ingredients necessary for electrification within a thunderstorm, while the updraft also plays a critical role in the development of severe and hazardous weather. Therefore utilizing this relationship, the monitoring of lightning rates and jumps provides an additional piece of information on the evolution of a thunderstorm, more often than not, at higher temporal resolution than current operational radar systems. This correlation is the basis for the total lightning jump algorithm that has been developed in recent years. Currently, the lightning jump algorithm is being tested in two separate but important efforts. Schultz et al. (2014; this conference) is exploring the transition of the algorithm from its research based formulation to a fully objective algorithm that includes storm tracking, Geostationary Lightning Mapper (GLM) Proxy data and the lightning jump algorithm. Chronis et al. (2014; this conference) provides context for the transition to current operational forecasting using lightning mapping array based products. However, what remains is an end-to-end physical and dynamical basis for coupling total lightning flash rates to severe storm manifestation, so the forecaster has a reason beyond simple correlation to utilize the lightning jump algorithm within their severe storm conceptual models. Therefore, the physical basis for the lightning jump algorithm in relation to severe storm dynamics and microphysics is a key component that must be further explored. Many radar studies have examined flash rates and their relationship to updraft strength, updraft volume, precipitation-sized ice mass, etc.; however, their relationship specifically to lightning jumps is fragmented within the literature. Thus the goal of this study is to use multiple Doppler and polarimetric radar techniques to resolve the physical and dynamical storm characteristics specifically around the time of the lightning jump. This information will help forecasters anticipate lightning jump occurrence, or even be of use to determine future characteristics of a given storm (e.g., development of a mesocyclone, downdraft, or hail signature on radar), providing additional lead time/confidence in the severe storm warning paradigm.

Schultz, Christopher J.↗

NASA NTRS2014

Physical and Dynamical Linkages Between Lightning Jumps and Storm Conceptual Models

The presence and rates of total lightning are both correlated to and physically dependent upon storm updraft strength, mixed phase precipitation volume and the size of the charging zone. The updraft modulates the ingredients necessary for electrification within a thunderstorm, while the updraft also plays a critical role in the development of severe and hazardous weather. Therefore utilizing this relationship, the monitoring of lightning rates and jumps provides an additional piece of information on the evolution of a thunderstorm, more often than not, at higher temporal resolution than current operational radar systems. This correlation is the basis for the total lightning jump algorithm that has been developed in recent years. Currently, the lightning jump algorithm is being tested in two separate but important efforts. Schultz et al. (2014; this conference) is exploring the transition of the algorithm from its research based formulation to a fully objective algorithm that includes storm tracking, Geostationary Lightning Mapper (GLM) Proxy data and the lightning jump algorithm. Chronis et al. (2014) provides context for the transition to current operational forecasting using lightning mapping array based products. However, what remains is an end-to-end physical and dynamical basis for coupling total lightning flash rates to severe storm manifestation, so the forecaster has a reason beyond simple correlation to utilize the lightning jump algorithm within their severe storm conceptual models. Therefore, the physical basis for the lightning jump algorithm in relation to severe storm dynamics and microphysics is a key component that must be further explored. Many radar studies have examined flash rates and their relationship to updraft strength, updraft volume, precipitation-sized ice mass, etc.; however, their relationship specifically to lightning jumps is fragmented within the literature. Thus the goal of this study is to use multiple Doppler and polarimetric radar techniques to resolve the physical and dynamical storm characteristics specifically around the time of the lightning jump. This information will help forecasters anticipate lightning jump occurrence, or even be of use to determine future characteristics of a given storm (e.g., development of a mesocyclone, downdraft, or hail signature on radar), providing additional lead time/confidence in the severe storm warning paradigm.

Schultz, Christopher J.↗

DOE OSTI2026

Coupled CVD and Float Zone Reactor for Lower Cost, Higher Efficiency Si Boules (Final Technical Report)

This project modeled a new type of photovoltaic (PV) Si production reactor with the promise to reduce the cost, increase the efficiency, and reduce the energy required to manufacture Si wafers. The production of photovoltaic (PV) grade Si is well established, based on the pulling of single crystalline Si boules from polycrystalline Si created from trichlorosilane using the Siemens process. However, these processes are very energy intensive, and manufacturing of PV Si occurs almost entirely in China. To disrupt this paradigm and on-shore production of this critical material and provide benefits to the public, a substantial technological leap is required to move past incumbent technology. This study evaluated a new float zone chemical vapor deposition (Fz-CVD) concept in which trichlorosilane (TCS), the feedstock for polysilicon in the Siemens process, is injected directly into a float zone crystallizer to continuously deposit the feed rod for the boule pulling process through a combination of multiphysics modeling and technoeconomic analysis.

14 SOLAR ENERGY↗

DOE OSTI2023

Growth interface study of CdTeSe crystals grown by the THM technique

The Traveling Heater Method (THM) is a widely accepted technique to grow high-quality detector grade CdTe and CdZnTe ingots, especially for X-ray and gamma-ray detector applications. Unlike melt-growth techniques, the growth interface for ingots produced by the THM technique consists of two different compounds, viz. the solidified region (just below the interface) consists of the compound to be grown (e.g., CdZnTe for CdZnTe growth), while the molten zone just above the growth interface consists of Te-rich CdZnTe. Thus, optimization of the growth parameters is critical to obtain a clean growth interface with the required shape and presence of minimal Te-rich inclusions. Here, in this study, CdTeSe ingots were grown employing the THM technique to investigate the growth interface. Both macroscopic and microscopic behavior of the interface were studied. The study revealed that a microscopically smooth growth interface can be achieved by optimizing the growth parameters, which is essential for obtaining high-quality, inclusion-free ingots.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

NASA NTRS1974

Vibration response of spacecraft shrouds to in-flight fluctuating pressures

Results are presented for the vibration response of a spacecraft shroud to a range of in-flight fluctuation pressures. An Atlas-Agena 15 degree cone-cylinder shroud was analyzed during the present study, and three critical flight Mach numbers were considered. At transonic Mach numbers, the aerodynamic flow over the shroud is complex, involving zones of regular attached flow, separated flow, shock wave oscillation, and modified attached flows induced by local thickening of the boundary layer. The overall shroud vibration levels for a particular Mach number were determined by initially calculating the mean square acceleration levels induced by the fluctuating pressures distributed over an individual zone, and then summing mean square acceleration levels in one-third octave bands over all zones.

Cockburn, J. A.↗

NASA NTRS2019

Boundary Condition Controls on the High-Sand-Flux Regions of Mars

Wind has been an enduring geologic agent throughout the history of Mars, but it is often unclear where and why sediment is mobile in the current epoch. We investigated whether eolian bed-form (dune and ripple) transport rates are depressed or enhanced in some areas by local or regional boundary conditions (e.g., topography, sand supply/availability). Bedform heights, migration rates, and sand fluxes all span two to three orders of magnitude across Mars, but we found that areas with the highest sand fluxes are concentrated in three regions: Syrtis Major, Hellespontus Montes, and the north polar erg. All regions are located near prominent transition zones of topography (e.g., basins, polar caps) and thermophysical properties (e.g., albedo variations); these are not known to be critical terrestrial boundary conditions. The two regions adjacent to major impact basins (Hellas and Isidis Planitia) showed radially outward upslope winds driving sand movement, although seasonally reversing wind regimes were also observed. The northern polar dunes yielded the highest known fluxes on the planet, driven by summer katabatic winds modulated by the seasonal CO2 cap retreat—processes not known to affect terrestrial dunes. In contrast, southern dune fields (<45°S) were less mobile, likely as a result of seasonal frost and ground ice suppressing sand availability. Results suggest that, unlike on Earth, large-scale topographic and thermophysical variabilities play a leading role in driving sand fluxes on Mars.

Matthew Chojnacki↗