Search NASA⌕ Search

SEARCH · Search NASA

Results for “DETONATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2016

A Case for Basic Rotating Detonation Engine Research

A brief review is provided covering the benefits to air breathing and chemical rocket propulsion found from pressure gain combustion in general, and rotating detonation in particular. Challenges are also identified.

propulsion↗
NASA NTRSDate not supplied

Rotating Detonation Rocket Engine (RDRE)

This poster is a general description of Rotating Detonation Rocket Engine task under the GCD project. It includes a brief summary of accomplishments for FY20. The scope of this work is to develop computational tools and design rules for RDRE’s.

Computational Fluid Dynamics↗
NASA NTRSDate not supplied

Experimental and Computational Analysis of a Rotating Detonation Combustor

Rotating detonation combustor (RDC) research has progressed along parallel experimental and computational paths with limited opportunities for validation. Validation is a crucial step to ensure RDC simulations provide an accurate representation of the physical phenomena, and thus, can be used with confidence for design optimization in different applications. In this study, data from a quasi-two-dimensional computational fluid dynamic simulation in an annular RDC are compared with experimental measurements including particle image velocimetry at 100 kHz. Results show good agreement between measured and simulated dynamic pressures, Chapman-Jouguet speeds, and static pressure distributions. Velocity measurements at the annulus exit show good temporal and quantitative agreement with simulations including spikes from the passing shock.

Detonation↗
NASA NTRSDate not supplied

Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle

A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.

detonation↗
NASA NTRSDate not supplied

Computational Fluid Dynamic Optimization of an Experimental Rotating Detonation Rocket Engine Nozzle

A parametric optimization study is performed on the nozzle of a laboratory rotating detonation rocket engine (RDRE) using a three-dimensional computational fluid dynamic simulation. The primary optimization objective is maximum nozzle thrust. The basic nozzle configuration is a shrouded, truncated plug. The fluid in the RDRE chamber leading to the nozzle is choked at its exit so that its cyclic behavior is unaffected by any changes to the nozzle design. Optimization is performed for a single operating point. Parameters varied are the overall nozzle area expansion ratio and the fraction of the expansion area that is provided by the shroud. These two parameters indirectly affect the angle of the plug nozzle cone, and the bluff body area associated with its truncation. Nozzle thrust is evaluated as the difference between the thrust of the RDRE chamber-plus-nozzle combination and that of the chamber alone. The nozzle produces approximately 20% of the total engine thrust. The baseline nozzle is found to perform well, yielding 58.1% of the thrust calculated for a notional ideal RDRE nozzle which can instantaneously change shape to allow isentropic expansion of every fluid element. Optimization improves the performance, bringing the nozzle thrust to 70.0% of the notional ideal, and total engine thrust (chamber-plus-nozzle) to 94% of the ideal.

detonation↗
NASA NTRSDate not supplied

Rotating Detonation Research at NASA

An invited presentation on the scope and content of NASA research and investments in Rotating Detonation Engine concepts for both airbreathing and rocket applications.

Detonation↗
NASA NTRS2025

Rotating Detonation Rocket Engine Concept Development

Programmatic overview of rotating detonation rocket engine (RDRE) research at NASA GRC for Scientific American for reference for Scientific American article. This is a compilation of previously released slides. This material will NOT be published as part of the article, but are being provided for background information.

Propulsion↗
NASA NTRSDate not supplied

Analysis of Integrated Spacecraft Performance Using A Rotating Detonation Rocket Engine

For spacecraft with especially stringent mass fraction constraints, the use of a rotating detonation rocket engine (RDRE) may yield potentially significant system mass savings. The pressure gain combustion inherent to RDREs provides higher thrust than traditional rocket engines for a given supply pressure and throat area. This opens multiple avenues for reducing system mass via higher specific impulse, reduced gravity losses, and reduced feed pressures. To highlight the potentially weight-saving characteristics of RDRE systems, the integrated performance of representative spacecraft designs using either a conventional rocket engine or an RDRE was assessed. This paper details the assumptions, methods, and results of this trade study. Two representative spacecraft were assessed. The first is a Liquid Mars Ascent Vehicle (MAV). This spacecraft was designed by NASA in 2011 for the Mars Sample Return Campaign but was not selected for flight due in part to it exceeding the mass requirements by 119 lbm. The second is MIURA-1, a kerolox sounding rocket developed by Payload Aerospace S.L.. The Liquid MAV assessment showed that an RDRE powered design met the mass requirements with a total vehicle mass 46 lbm below the limit. The MIURA-1 assessment showed that wall heat transfer and regenerative cooling are significant challenges for kerolox RDREs, but these challenges may be mitigated by reducing mixture ratio and using both propellants to cool the chamber. The assessment showed that an RDRE powered sounding rocket could achieve 12% more microgravity time than a conventional sounding rocket with the same payload and total vehicle mass. Alternately, if the payload mass and target apogee are held constant, then an RDRE powered sounding rocket can be 8% shorter and 11% lighter than a conventional sounding rocket. These results suggest that the advent of RDREs for in-space propulsion may unlock new missions for which conventional propulsion is not feasible.

Rotating Detonation Rocket Engine↗
NASA NTRSDate not supplied

Analysis of Integrated Spacecraft Performance Using Rotating Detonation Rocket Engine

For spacecraft with especially stringent mass fraction constraints, the use of a rotating detonation rocket engine (RDRE) may yield potentially significant system mass savings. The pressure gain combustion inherent to RDREs provides higher thrust than traditional rocket engines for a given supply pressure and throat area. This opens multiple avenues for reducing system mass via higher specific impulse, reduced gravity losses, and reduced feed pressures. To highlight the potentially weight-saving characteristics of RDRE systems, the integrated performance of representative spacecraft designs using either a conventional rocket engine or an RDRE was assessed. This paper details the assumptions, methods, and results of this trade study. Two representative spacecraft were assessed. The first is a Liquid Mars Ascent Vehicle (MAV). This spacecraft was designed by NASA in 2011 for the Mars Sample Return Campaign but was not selected for flight due in part to it exceeding the mass requirements by 119 lbm. The second is MIURA-1, a kerolox sounding rocket developed by Payload Aerospace S.L.. The Liquid MAV assessment showed that an RDRE powered design met the mass requirements with a total vehicle mass 46 lbm below the limit. The MIURA-1 assessment showed that wall heat transfer and regenerative cooling are significant challenges for kerolox RDREs, but these challenges may be mitigated by reducing mixture ratio and using both propellants to cool the chamber. The assessment showed that an RDRE powered sounding rocket could achieve 12% more microgravity time than a conventional sounding rocket with the same payload and total vehicle mass. Alternately, if the payload mass and target apogee are held constant, then an RDRE powered sounding rocket can be 8% short and 11% lighter than a conventional sounding rocket. These results suggest that the advent of RDREs for in-space propulsion may unlock new missions for which conventional propulsion is not feasible.

Rotating Detonation Rocket Engine↗
NASA NTRSDate not supplied

Parameterized Study of Heat Load Trends in a Subscale Rotating Detonation Rocket Engine

NASA has developed a subscale rotating detonation rocket engine platform, enabling rapid parameterization of components and their associated performances. A major performance metric of interest for RDREs is the total heat absorbed at a given operating condition and wave mode operation. To investigate this, several sets of hardware were produced to have variation of the contraction ratio, injector geometry, and length. A wide range of total mass flow rates and mixture ratios were also explored using gaseous methane/oxygen. All hardware was produced using laser powder bed fusion GRCop-42, GRX-810, or C-103 alloys depending on the component cooling requirements. Outer and inner body hardware were made from GRCop-42 where heat fluxes were expected to be high and were water cooled through integrated coolant channels. Nozzles were made from C-103 which are radiatively cooled. Finally, the injectors were produced using GRCop-42 or GRX-810 as passive cooling via propellant injection has previously found to be sufficient given the small gap width of exposed injection surface. Total heat load and bulk heat flux measurements to the hot walls are reported. Trends in heat load and heat flux are shown with relation to parameters such as chamber pressure, area ratio, and wave mode. Heat loads between the inner and outer bodies and the chamber and shroud section are compared.

Heat Flux↗
NASA NTRSDate not supplied

Parameterized Study of Heat Load Trends in a Subscale Rotating Detonation Rocket Engine

NASA has developed a subscale rotating detonation rocket engine platform, enabling rapid parameterization of components and their associated performances. A major performance metric of interest for RDREs is the total heat absorbed at a given operating condition and wave mode operation. To investigate this, several sets of hardware were produced to have variation of the contraction ratio, injector geometry, and length. A wide range of total mass flow rates and mixture ratios were also explored using gaseous methane/oxygen. All hardware was produced using laser powder bed fusion GRCop-42, GRX-810, or C-103 alloys depending on the component cooling requirements. Outer and inner body hardware were made from GRCop-42 where heat fluxes were expected to be high and were water cooled through integrated coolant channels. Nozzles were made from C-103 which are radiatively cooled. Finally, the injectors were produced using GRCop-42 or GRX-810 as passive cooling via propellant injection has previously found to be sufficient given the small gap width of exposed injection surface. Total heat load and bulk heat flux measurements to the hot walls are reported. Trends in heat load and heat flux are shown with relation to parameters such as chamber pressure, area ratio, and wave mode. Heat loads between the inner and outer bodies and the chamber and shroud section are compared.

Heat Loads↗
DOE OSTI2025

Z Machine Detonator Holder Testing

Current packaging for the detonators used on the Z Machine is dirty, not well suited for reusability, and labor intensive to use. A new packaging design is developed, explosively tested, and approved by the numerous stakeholders resulting in more efficient operations and lowered costs.

42 ENGINEERING↗
DOE OSTI2025

Modeling detonation with CartaBlanca simulations

The accurate modeling of high explosive (HE) detonation and the con- sequent large solid deformation, failure, plastic flow, porosity growth, and shock wave propagation is important because simulations can capture spatial and temporal features that experimental diagnostics cannot capture. However, the simulation of the explosive event poses challenges to a computational scientist. These include the accurate modeling of ductile damage, crack formation, plastic deformation, as well as physical and nu- merical instabilities. The material response can be history-dependent and subject to large material deformation. Our research simulates the impact of a high explosive (Detasheet) onto a tantulum metal plate. We performed the simulations using CartaBlanca at different mesh resolutions. We decided the study would be impactful if we perform the simulations with the Material Point Method. Differences were observed at the different mesh resolutions in velocity and nodal stress magnitude, so increased mesh resolutions may be required. In addition, the Discontinuous Galerkin method would be needed to account for the large gas expansion.

97 MATHEMATICS AND COMPUTING↗