SEARCH · Search NASA

Results for “Data Characterization”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

DOE OSTI2019

Abstract for CRADA between the National Energy Technology Laboratory and Strategic Power Systems, Inc. (AGMT-0884)

This project will utilize field data, available through the Operational Reliability Analysis Program (ORAP®), to assess the operation of natural gas combined cycle (NGCC) and coal fired plants in cyclic duty. The emphasis will be on Heat Recovery Steam Generator (HRSG) and coal-fired boiler operating conditions and failure experience related to tube failures. The project will be based on high-fidelity data available in ORAP through the collection of near real time process data characterizing the operating environment and dynamic conditions, from start up to shut-down, that affect the HRSG and coal-fired boiler (i.e. the boiler tubes). It is important to understand the operating environment to assess the influence of the cyclic start-stop cycles, time at temperature, and other operating conditions that can be seen in the data, with their possible impact on the life and reparability of the boiler tubes. This knowledge is important to influence/develop a predictive operations and maintenance strategy to improve performance, increase life, and reduce cost.

20 FOSSIL-FUELED POWER PLANTS↗

DOE OSTI2020

Sediment Mineralogy Data Review for the Hanford Central Plateau

The compendium of Hanford site sediment mineralogy data provided in this report was initiated in 2012 to support flux mitigation technologies and real-time monitoring that could limit contaminant fluxes to the groundwater in the Central Plateau. Recent efforts in advancing spectral induced polarization as a method for monitoring contaminant transformations for active biogeochemical remedies have underscored the need for a published compendium of sediment characterization data. Although the data are primarily focused on the mineralogical composition of Hanford sediments, other soil measurements such as particle size distribution such as particle size distribution and carbon content are provided. The data have been reproduced from the original reports and are provided here for information only (FIO).

58 GEOSCIENCES↗

DOE OSTI2020

CACTI Radar b1 Processing: Corrections, Calibrations, and Processing Report

The U.S. Department of Energy’s (DOE) Atmospheric Radiation Measurement (ARM) user facility deployed a large number of instruments to a region nearby the Sierra de Córdobas mountains in Argentina as part of the Cloud, Aerosol, and Complex Terrain Interactions (CACTI) field campaign (1). During this campaign, four radars were installed at a site outside of Villa Yacanto as shown in Figure 1. As part of a post-campaign effort to improve the usability of these data, a significant activity was undertaken towards the calibration, correction, and improvement of the data quality of these radar datastreams. This process in ARM nomenclature is referred to as generating a “b1” datastream. While these “b1” standards may imply different corrections or standards for various ARM instruments, for radars it refers to a datastream that has been calibrated (and cross-calibrated), including a serious effort to deliver the highest-quality (well-characterized) data possible. This report details (i) the status/quality of the original “a1” (raw) data, (ii) the corrections and calibrations that are applied to generate these b1 datastreams, (iii) the details of the applied algorithms and how radar offset/calibration numbers were determined for the eventual corrections, and (iv) the new and flexible plug-in-based processing system designed during CACTI for radar b1 activities (current, future) that interfaces with ARM’s Data Integrator (ADI) and high-performance computing (HPC) system.

47 OTHER INSTRUMENTATION↗

DOE OSTI2023

Utah FORGE: Powder X-ray Diffraction Data from Well 16A(78)-32 Core

This dataset from Lawrence Livermore National Laboratory (LLNL) consists of four raw X-ray diffraction (XRD) scans and preliminary results of quantitative XRD analysis. The scanned samples were prepared from four subcores, which came from various depths of the FORGE well 16A(78)-32 core. Desired core lengths were selected from available core photos (on GDR), provided by FORGE personnel, and subcored at LLNL. The XRD scans were collected in May 2023 at LLNL as pre-experimental characterization data for these subcores, which will be used in core-flooding experiments at LLNL and in triaxial direct shear experiments at Los Alamos National Laboratory as part of DOE Project 5-2428. XRD scans are in RAW file format (e.g., FORGE-5477-full.raw) and are suitable for viewing and analysis using open-source quantitative XRD software (e.g., Profex; www.profex-xrd.org ) and/or other proprietary instrument software.

15 GEOTHERMAL ENERGY↗

DOE OSTI2020

(Oxy)hydroxides Formed on Aluminum Fuel Materials After Irradiation and Long-Term Wet Storage - 20354

The aluminum cladding of research-reactor fuel experiences general corrosion when in contact with water during in-reactor service and post-discharge wet storage, resulting in the formation of adherent aluminum (oxy)hydroxide films. These (oxy)hydroxides contain chemically-bound water that poses challenges for extended dry storage due to the risk of thermal or radiolytic decomposition releasing free water and/or hydrogen and oxygen gases. This study describes characterization of the (oxy)hydroxides present on several aluminum materials used in reactor operation and subsequently stored wet in the L-Basin storage facility at the Savannah River Site (SRS) for an extended period. Characterization data providing insight into the loading, composition, and morphology of (oxy)hydroxides to be expected on service-exposed aluminum cladding provides valuable benchmarks for designing adequate drying and dry-storage approaches. This work is part of a broader investigation to address knowledge gaps and technical data needs for dry storage of aluminum-clad spent nuclear fuel (ASNF), which included in-lab growth of (oxy)hydroxide films on aluminum alloy substrates to investigate formation behavior, investigation of drying methods to remove existing (oxy)hydroxides from ASNF cladding, and measurement of radiolytic yield of hydrogen from (oxy)hydroxide powders and films. In this study, (oxy)hydroxide films were characterized for three aluminum-alloy materials used in reactors and subsequently stored wet for up to approximately 40 years in L-Basin at SRS: one cropping from a Missouri University Research Reactor (MURR) fuel element (Al-6061 alloy), one cropping from a Universal Sleeve Housing (USH) (Al-6063 alloy), and one Mark-16B fuel assembly (either Al-6061 or Al- 6063). The USH and Mark-16B were used in SRS production reactors. Characterization of the as-received (oxy)hydroxides included scanning electron microscopy (SEM) in both plan-view and cross-section to characterize the (oxy)hydroxide layer's morphology, thickness, and structure. X-ray diffraction (XRD) was used to identify the chemical composition and distinguish between the various aluminum (oxy)hydroxides known to form under reactor and storage conditions. XRD analysis revealed both bayerite (Al(OH)3) and boehmite (AlOOH) on the surface of the MURR and USH samples, as well as bayerite, boehmite, and gibbsite (another Al(OH)3 polymorph) on the surface of the Mark-16B sample. The aluminum trihydroxides, bayerite and gibbsite, are typically associated with corrosion in low-temperature (<80 deg. C) water, while boehmite is expected to form at higher water temperature (>80 deg. C). The presence of bayerite on the USH, which is believed to have operated close to 90 deg. C, suggests that boehmite formed during in-reactor exposure was not protective against further hydroxide growth in low-temperature wet storage. Cross-section scanning electron microscopy (SEM) showed total (oxy)hydroxide layer thicknesses of ∼5- 10 μm for the MURR and ∼5-15 μm for the Mark-16B. The thickness of the USH's (oxy)hydroxide layer was indiscernible by the current mounting and imaging method, despite plan-view SEM and XRD confirming the presence of an (oxy)hydroxide layer. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2014

Visualization of the operational space of edge-localized modes through low-dimensional embedding of probability distributions

Information visualization aimed at facilitating human perception is an important tool for the interpretation of experiments on the basis of complex multidimensional data characterizing the operational space of fusion devices. This work describes a method for visualizing the operational space on a two-dimensional map and applies it to the discrimination of type I and type III edge-localized modes (ELMs) from a series of carbon-wall ELMy discharges at JET. The approach accounts for stochastic uncertainties that play an important role in fusion data sets, by modeling measurements with probability distributions in a metric space. The method is aimed at contributing to physical understanding of ELMs as well as their control. Furthermore, it is a general method that can be applied to the modeling of various other plasma phenomena as well.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

DOE OSTI2018

Evaluation of the Impacts of Heat Exchanger Operation on Quality of Water Used as Heat Source and Sink

To help inform future decisions about the subsequent uses of water that has served as a heat source and sink in the heat exchanger component of a geothermal heat pump system, ORNL performed an independent assessment of data characterizing the quality of water that had passed through a heat exchanger supporting a geothermal heat pump in a school building. Water supply to the heat exchanger is treated drinking water from a public water supply system that derives its water from a groundwater source. Water analyses and bacteriological measurements collected from heat exchanger and inflow and outflow lines were supplied to ORNL for review. Data were compared with regulatory standards and inflow and outflow data were compared to identify changes occurring in the water resulting from its passage through the heat exchanger. Review of the data identified no conditions that would prevent the use of heat exchange outflow water for water supply. Water quality conforms with applicable regulatory standards. There were no discernible differences between inflow and outflow water quality for any parameters other than water temperature and formation of heterotrophic bacterial biofilms. Changes in water temperature are an expected result of the operation of the heat exchanger system and do not by themselves affect the suitability of the water for human consumption. Bacterial biofilm formation can be affected by water temperature, but the data did not show a consistent or statistically significant relationship between temperature parameters and biofilm formation, and the observations of biofilms formed in the heat exchanger water lines do not affect the suitability of the outflow water for water supply. Legionella, a bacterial genus that has been associated with outbreaks of waterborne pathogenic disease, was detected in one biofilm sample, and the water company is performing follow-up testing to assess the significance of this detection.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

An expanded registry of candidate cis -regulatory elements

Mammalian genomes contain millions of regulatory elements that control the complex patterns of gene expression. Previously, the ENCODE consortium mapped biochemical signals across hundreds of cell types and tissues and integrated these data to develop a registry containing 0.9 million human and 300,000 mouse candidate cis-regulatory elements (cCREs) annotated with potential functions. Here we have expanded the registry to include 2.37 million human and 967,000 mouse cCREs, leveraging new ENCODE datasets and enhanced computational methods. This expanded registry covers hundreds of unique cell and tissue types, providing a comprehensive understanding of gene regulation. Functional characterization data from assays such as STARR-seq, massively parallel reporter assay, CRISPR perturbation and transgenic mouse assays have profiled more than 90% of human cCREs, revealing complex regulatory functions. We identified thousands of novel silencer cCREs and demonstrated their dual enhancer and silencer roles in different cellular contexts. Integrating the registry with other ENCODE annotations facilitates genetic variation interpretation and trait-associated gene identification, exemplified by the identification of KLF1 as a novel causal gene for red blood cell traits. This expanded registry is a valuable resource for studying the regulatory genome and its impact on health and disease.

Moore, Jill E. [Univ. of Massachusetts, Worchester↗

NASA NTRS2011

Airborne Remote Observations of L-Band Radio Frequency Interference and Implications for Satellite Missions

Passive remote sensing of the Earth s surface and atmosphere from space has significant importance in operational and research environmental studies, in particular for the scientific understanding, monitoring and prediction of climate change and its impacts. Passive remote sensing requires the measurement of naturally occurring radiations, usually of very low power levels, which contain essential information on the physical process under investigation. As such, these sensed radio frequency bands are a unique natural resource enabling space borne passive sensing of the atmosphere and the Earth s surface that deserves adequate allocation to the Earth Exploration Satellite Service and absolute protection from interference. Unfortunately, radio frequency interference (RFI) is an increasing problem for Earth remote sensing, particularly for passive observations of natural emissions. Because these natural signals tend to be very weak, even low levels of interference received by a passive sensor may degrade the fidelity of scientific data. The characteristics of RFI (low-level interference and radar-pulse noise) are not well known because there has been no systematic surveillance, spectrum inventory or mapping of RFI. While conducting a flight experiment over central Tennessee in May 2010, RFI, a concern for any instrument operating in the passive L band frequency, was observed across 16 subbands between 1402-1427 MHz. Such a survey provides rare characterization data from which to further develop mitigation technologies as well as to identify bandwidths to avoid in future sensor formulation.

Laymon, Charles↗

DOE OSTI2024

Simulant Development of Potential 200 West Area Waste Feeds

Preliminary planning for retrieval, qualification, and pretreatment of waste in Hanford’s 200 West Area (200W) has begun as part of the West Area Risk Management project. Experimental studies to technically mature pretreatment process operations will likely be needed because of the uniqueness of 200W waste. Pacific Northwest National Laboratory formulated five simulants to represent 200W-qualified feed based on the preliminary flowsheet provided by Washington River Protection Solutions, LLC. The simulant recipes were devised using applicable historical information as a reference point to support the use of the flowsheet waste vectors, which were combined into five distinct groups. These five groups formed the basis for the liquid composition targets that were adapted into recipes using charged-balanced salt species. The liquid phase recipes were batched in 1-L quantities and analyzed at Pacific Northwest National Laboratory. Once confirmed to be stable, the liquid solutions were tested for compatibility with candidate solid components. Specific solid components were recommended based on cross-examining the proposed solid phases in the flowsheet with relevant data from the literature. Mixtures of solid components were added to aliquots of the liquid batches and sub-sampled to measure particle size distribution. The measured distribution was compared to independently created benchmark distributions appropriate for each simulant. This process was iterated until a solid phase composition that resulted in a representative particle size distribution was found. After the final compositions were confirmed, a suite of chemical and physical characterization data was collected. This report describes the simulant basis, formulation methodology, laboratory measurements, and data collected for the recipes recommended to represent 200W waste feeds.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

CryoTARPOS Vibration Mitigation System for Layered Experiments

The goal of this project is to implement a system that can eliminate or mitigate vibration so that clear images can be taken without bypassing the cryocooler. By allowing for layer characterization and cryocooler operation at the same time, cooling capacity and thermal stability of the target would be improved, and more layer characterization data could be taken. Increased cooling capacity and thermal stability could allow for layering during occasional off normal conditions that would typically result in a loss of temperature control and NIF operational delays ranging from several hours to several days per month. The increased cooling capacity and thermal stability could also allow for layering of new target platforms that have less cooling margin. Additional layer images could be used for better characterization of defects and non-uniformities in the layer and would reduce the likelihood of layer seed loss, which typically adds ~12 hours per week in layering time. Motion blur from vibration due to off normal activity in the NIF Target Bay could also be mitigated that would usually result in NIF operational delays of several hours every month.

42 ENGINEERING↗

DOE OSTI2016

S-Layer Nanosheet Binding of Zn and Gd

This data characterizes binding of Zn2+ and Gd3+ to engineered nanosheets at 40C and in a brine solution. The engineered nanosheets are composed of surface-layer (S-layer) proteins which form 2 D crystalline sheets and display Zn2+- or Gd3+-binding domains on these sheets. Their ability to bind Zn2+ is compared to S-layer nanosheets that do not contain Zn2+-binding domains. We found that the purification method of these nanosheets was a critical determinant of their function and thus have provided data on the binding from two different purification methods. A key distinction of this dataset from other datasets is that the engineered nanosheets were expressed and purified from E. coli grown at 37C as described in (Kinns, 2010; Howorka, 2000), References: Kinns, H., et al. Identifying assembly-inhibiting and assembly-tolerant sites in the SbsB S-layer protein from Geobacillus stearothermophilus. Journal of Molecular Biology, 2010. 395(4): p. 742-753. Howorka, S., et al. Surface-accessible residues in the monomeric and assembled forms of a bacterial surface layer protein. Journal of Biological Chemistry, 2000. 275(48): p. 37876-37886.

15 GEOTHERMAL ENERGY↗

NASA NTRS2010

Mode II Interlaminar Fracture Toughness and Fatigue Characterization of a Graphite Epoxy Composite Material

Mode II interlaminar fracture toughness and delamination onset and growth characterization data were generated for IM7/8552 graphite epoxy composite materials from two suppliers for use in fracture mechanics analyses. Both the fracture toughness testing and the fatigue testing were conducted using the End-notched Flexure (ENF) test. The ENF test for mode II fracture toughness is currently under review by ASTM as a potential standard test method. This current draft ASTM protocol was used as a guide to conduct the tests on the IM7/8552 material. This report summarizes the test approach, methods, procedures and results of this characterization effort.

O'Brien, T. Kevin↗

NASA NTRS1982

Characterization of an Experimental Referee Broadened Specification (ERBS) aviation turbine fuel and ERBS fuel blends

Characterization data and comparisons of these data are presented for three individual lots of a research test fuel designated as an Experimental Referee Broadened Specification (ERBS) aviation turbine fuel. This research fuel, which is a blend of kerosene and hydrotreated catalytic gas oil, is a representation of a kerojet fuel with broadened properties. To lower the hydrogen content of the ERBS fuel, a blending stock, composed of xylene bottoms and hydrotreated catalytic gas oil, was developed and employed to produce two different ERBS fuel blends. The ERBS fuel blends and the blending stock were also characterized and the results for the blends are compared to those of the original ERBS fuel. The characterization results indicate that with the exception of the freezing point for ERBS lot 2, which was slightly high, the three lots, produced over a 2 year period, met all general fuel requirements. However, although the properties of the fuels were found to be fairly consistent, there were differences in composition. Similarly, all major requirements for the ERBS fuel blends were met or closely approached, and the properties of the blended fuels were found to generally reflect those expected for the proportions of ERBS fuel and blending stock used in their production.

Seng, G. T.↗

NASA NTRS2003

Water Impact Test and Simulation of a Composite Energy Absorbing Fuselage Section

In March 2002, a 25-ft/s vertical drop test of a composite fuselage section was conducted onto water. The purpose of the test was to obtain experimental data characterizing the structural response of the fuselage section during water impact for comparison with two previous drop tests that were performed onto a rigid surface and soft soil. For the drop test, the fuselage section was configured with ten 100-lb. lead masses, five per side, that were attached to seat rails mounted to the floor. The fuselage section was raised to a height of 10-ft. and dropped vertically into a 15-ft. diameter pool filled to a depth of 3.5-ft. with water. Approximately 70 channels of data were collected during the drop test at a 10-kHz sampling rate. The test data were used to validate crash simulations of the water impact that were developed using the nonlinear, explicit transient dynamic codes, MSC.Dytran and LS-DYNA. The fuselage structure was modeled using shell and solid elements with a Lagrangian mesh, and the water was modeled with both Eulerian and Lagrangian techniques. The fluid-structure interactions were executed using the fast general coupling in MSC.Dytran and the Arbitrary Lagrange-Euler (ALE) coupling in LS-DYNA. Additionally, the smooth particle hydrodynamics (SPH) meshless Lagrangian technique was used in LS-DYNA to represent the fluid. The simulation results were correlated with the test data to validate the modeling approach. Additional simulation studies were performed to determine how changes in mesh density, mesh uniformity, fluid viscosity, and failure strain influence the test-analysis correlation.

Fasanella, Edwin L.↗

NASA NTRS2016

Airborne Mission Concept for Coastal Ocean Color and Ecosystems Research

NASA airborne missions in 2011 and 2013 over Monterey Bay, CA, demonstrated novel above- and in-water calibration and validation measurements supporting a combined airborne sensor approach (imaging spectrometer, microradiometers, and a sun photometer). The resultant airborne data characterize contemporaneous coastal atmospheric and aquatic properties plus sea-truth observations from state-of-the-art instrument systems spanning a next-generation spectral domain (320-875 nm). This airborne instrument suite for calibration, validation, and research flew at the lowest safe altitude (ca. 100 ft or 30 m) as well as higher altitudes (e.g., 6,000 ft or 1,800 m) above the sea surface covering a larger area in a single synoptic sortie than ship-based measurements at a few stations during the same sampling period. Data collection of coincident atmospheric and aquatic properties near the sea surface and at altitude allows the input of relevant variables into atmospheric correction schemes to improve the output of corrected imaging spectrometer data. Specific channels support legacy and next-generation satellite capabilities, and flights are planned to within 30 min of satellite overpass. This concept supports calibration and validation activities of ocean color phenomena (e.g., river plumes, algal blooms) and studies of water quality and coastal ecosystems. The 2011 COAST mission flew at 100 and 6,000 ft on a Twin Otter platform with flight plans accommodating the competing requirements of the sensor suite, which included the Coastal-Airborne In-situ Radiometers (C-AIR) for the first time. C-AIR (Biospherical Instruments Inc.) also flew in the 2013 OCEANIA mission at 100 and 1,000 ft on the Twin Otter below the California airborne simulation of the proposed NASA HyspIRI satellite system comprised of an imaging spectrometer and thermal infrared multispectral imager on the ER-2 at 65,000 ft (20,000 m). For both missions, the Compact-Optical Profiling System (Biospherical Instruments, Inc.), an in-water system with microradiometers matching C-AIR, was deployed to compare sea-truth measurements and low-altitude Twin Otter flights within Monterey Bay red tide events. This novel airborne and in-water sensor capability advances the science of coastal measurements and enables rapid response for coastal events.

Oceans↗

NASA NTRSDate not supplied

Analysis of Ice Mass Growth Over Time on the CRM65 Midspan Hybrid Model

The Aeronautics Research Mission Directorate at NASA is developing and applying tools to enable future technologies towards sustainable flight. Aircraft icing has been identified as a potential barrier to entry into service for innovative designs necessitating improvements to computational ice accretion tools. NASA is developing the Glenn Icing Computational Environment (GlennICE) to address deficiencies in the computational modeling capabilities of previously developed ice accretion solvers. To benchmark and improve the ability to model highly three-dimensional ice accretion, high quality validation data against experimental data is required. The CRM65 Midspan Hybrid geometry was previously tested at the NASA Icing Research Tunnel to generate experimental data for swept wing geometries typical for commercial transport aircraft. As a part of a 2018 icing test campaign, experimental data characterizing the relationship between ice accretion time and ice mass growth was obtained and can be leveraged for use in validation of computational tools. The desire for computational ice accretion solvers to predict ice shapes profiles accreted experimentally has often overshadowed the comparison to the mass and bulk volume of ice accreted. To address this deficiency, an analysis is presented in which GlennICE is applied to simulations of the CRM65 Midspan Hybrid model tested in the NASA Icing Research Tunnel. Results from the computational fluid dynamics simulations compared favorably to the experimental pressure coefficient data, thus validating the modeling setup. The experimental data showed excellent repeatability for the 15.0 minute accretion time. The comparisons between the experimental and computational ice mass over time showed good agreement up to 10.0 minutes after which the ice mass was underpredicted. The experimental ice mass was largely linear with some nonlinear data. The bulk volume of ice accreted experimentally compared well to GlennICE for the scanned ice shapes and mean combined cross section ice shapes, but was underpredicted for the maximum combined cross section ice shapes at longer accretion times. The experimental minimum combined cross section, mean combined cross section, and maximum combined cross section profiles when compared to GlennICE show good agreement for the mean combined cross section up to 15.0 minutes. The analyses show that with a single-shot method, GlennICE currently underpredicts the ice mass for longer accretion times, is not able to match the bulk volume of the maximum combined cross section due to dominating scallop features, and future work is required to generate a more generalized ice bulk density model.

Icing↗

NASA NTRSDate not supplied

Analysis of Ice Mass Growth Over Time on the CRM65 Midspan Hybrid Model

Icing↗