Results for “Equation learning” — Page 14

DOE OSTI2025

JAX-CanVeg: A Differentiable Land Surface Model

Land surface models consider the exchange of water, energy, and carbon along the soil-canopy-atmosphere continuum, which is challenging to model due to their complex interdependency and associated challenges in representing and parameterizing them. Differentiable modeling provides a new opportunity to capture these complex interactions by seamlessly hybridizing process-based models with deep neural networks (DNNs), benefiting both worlds, that is, the physical interpretation of process-based models and the learning power of DNNs. Here, we developed a differentiable land model, JAX-CanVeg. The new model builds on the legacy CanVeg by incorporating advanced functionalities through JAX in the graphic processing unit support, automatic differentiation, and integration with DNNs. We demonstrated JAX-CanVeg's hybrid modeling capability by applying the model at four flux tower sites with varying aridity. To this end, we developed a hybrid version of the Ball-Berry equation that emulates the water stress impact on stomatal closure to explore the capability of the hybrid model in (a) improving the simulations of latent heat fluxes (LE) and net ecosystem exchange (NEE), (b) improving the optimization trade-off when learning observations of both LE and NEE, and (c) benefiting a multi-layer canopy model setup. Our results show that the proposed hybrid model improved the simulations of LE and NEE at all sites, with an improved optimization trade-off over the process-based model. Additionally, the multi-layer canopy set benefited hybrid modeling at some sites. Anchored in differentiable modeling, our study provides a new avenue for modeling land-atmosphere interactions by leveraging the benefits of both data-driven learning and process-based modeling.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Classifying photonic topology using the spectral localizer and numerical K -theory

Recently, the spectral localizer framework has emerged as an efficient approach for classifying topology in photonic systems featuring local nonlinearities and radiative environments. In nonlinear systems, this framework provides rigorous definitions for concepts such as topological solitons and topological dynamics, where a system’s occupation induces a local change in its topology due to nonlinearity. For systems embedded in radiative environments that do not possess a shared bulk spectral gap, this framework enables the identification of local topology and shows that local topological protection is preserved despite the lack of a common gap. However, as the spectral localizer framework is rooted in the mathematics of C*-algebras, and not vector bundles, understanding and using this framework requires developing intuition for a somewhat different set of underlying concepts than those that appear in traditional approaches for classifying material topology. In this tutorial, we introduce the spectral localizer framework from a ground-up perspective and provide physically motivated arguments for understanding its local topological markers and associated local measure of topological protection. In doing so, we provide numerous examples of the framework’s application to a variety of topological classes, including crystalline and higher-order topology. We then show how Maxwell’s equations can be reformulated to be compatible with the spectral localizer framework, including the possibility of radiative boundary conditions. To aid in this introduction, we also provide a physics-oriented introduction to multi-operator pseudospectral methods and numerical K-theory, two mathematical concepts that form the foundation for the spectral localizer framework. Finally, we provide some mathematically oriented comments on the C*-algebraic origins of this framework, including a discussion of real C*-algebras and graded C*-algebras that are necessary for incorporating physical symmetries. Looking forward, we hope that this tutorial will serve as an approachable starting point for learning the foundations of the spectral localizer framework.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2026

Discovery of Probabilistic Dirichlet-to-Neumann Maps on Graphs

Dirichlet-to-Neumann maps enable the coupling of multiphysics simulations across computational subdomains by ensuring continuity of state variables and fluxes at artificial interfaces. We present a novel method for learning Dirichlet-to-Neumann maps on graphs using Gaussian processes, specifically for problems where the data obey a conservation law arising from an underlying partial differential equation. Our approach combines discrete exterior calculus and nonlinear optimal recovery to infer relationships between vertex and edge values. This framework yields data-driven predictions with uncertainty quantification across the entire graph, even when observations are limited to a subset of vertices and edges. By minimizing the reproducing kernel Hilbert space norm while penalizing kernel complexity through maximum likelihood estimation, our method ensures that the resulting surrogate strictly enforces conservation laws without overfitting. We demonstrate our method on two representative applications: subsurface flow in fracture networks and arterial blood flow. Finally, the results demonstrate that the method maintains high accuracy and well-calibrated uncertainty estimates even under severe data scarcity, highlighting its potential for scientific applications where limited data and reliable uncertainty quantification are critical.

Dirichlet-to-Neumann map↗

NASA NTRS1992

Neurodynamical model of collective brain

A dynamical system which mimics collective purposeful activities of a set of units of intelligence is introduced and discussed. A global control of the unit activities is replaced by the probabilistic correlations between them. These correlations are learned during a long term period of performing collective tasks, and are stored in the synaptic interconnections. The model is represented by a system of ordinary differential equations with terminal attractors and repellers, and does not contain any man-made digital devices.

Zak, Michail↗

NASA NTRS1993

MEDUSA - An overset grid flow solver for network-based parallel computer systems

Continuing improvement in processing speed has made it feasible to solve the Reynolds-Averaged Navier-Stokes equations for simple three-dimensional flows on advanced workstations. Combining multiple workstations into a network-based heterogeneous parallel computer allows the application of programming principles learned on MIMD (Multiple Instruction Multiple Data) distributed memory parallel computers to the solution of larger problems. An overset-grid flow solution code has been developed which uses a cluster of workstations as a network-based parallel computer. Inter-process communication is provided by the Parallel Virtual Machine (PVM) software. Solution speed equivalent to one-third of a Cray-YMP processor has been achieved from a cluster of nine commonly used engineering workstation processors. Load imbalance and communication overhead are the principal impediments to parallel efficiency in this application.

Smith, Merritt H.↗

NASA NTRS1989

Evolution of the solar nebula. I - Nonaxisymmetric structure during nebula formation

Numerical solutions of the equations of hydrodynamics, gravitation, and radiative transfer in three spatial dimensions are used to model the formation and time evolution of the early solar nebula in order to learn whether or not gravitational torques between nonaxisymmetric structures in the solar nebula can transport angular momentum rapidly enough to produce nebula clearing on astronomically indicated (10 to the 5 to 10 to the 7 yr) time scales. The models involve solutions for the collapse of spherical clouds with assumed initial density and rotation profiles onto protosuns of variable mass. Most of the models assume uniform initial density and rotation, and have variations in the initial parameters of cloud mass, cloud rotation rate, and protosun mass which are chosen to simulate a range of possible phases of early solar nebula evolution. The models show little tendency for directly forming small numbers of giant gaseous protoplanets through gaseous gravitational instability.

Boss, Alan P.↗

NASA NTRS2008

Sensing a Changing Chemical Mixture Using an Electronic Nose

A method of using an electronic nose to detect an airborne mixture of known chemical compounds and measure the temporally varying concentrations of the individual compounds is undergoing development. In a typical intended application, the method would be used to monitor the air in an inhabited space (e.g., the interior of a building) for the release of solvents, toxic fumes, and other compounds that are regarded as contaminants. At the present state of development, the method affords a capability for identifying and quantitating one or two compounds that are members of a set of some number (typically of the order of a dozen) known compounds. In principle, the method could be extended to enable monitoring of more than two compounds. An electronic nose consists of an array of sensors, typically made from polymer carbon composites, the electrical resistances of which change upon exposure to a variety of chemicals. By design, each sensor is unique in its responses to these chemicals: some or all of the sensitivities of a given sensor to the various vapors differ from the corresponding sensitivities of other sensors. In general, the responses of the sensors are nonlinear functions of the concentrations of the chemicals. Hence, mathematically, the monitoring problem is to solve the set of time-dependent nonlinear equations for the sensor responses to obtain the time dependent concentrations of individual compounds. In the present developmental method, successive approximations of the solution are generated by a learning algorithm based on independent-component analysis (ICA) an established information theoretic approach for transforming a vector of observed interdependent signals into a set of signals that are as nearly statistically independent as possible.

Duong, Tuan↗

NASA NTRS2014

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Gorazd Medic↗

NASA NTRS2014

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Gorazd Medic↗

NASA NTRS2017

High Efficiency Centrifugal Compressor for Rotorcraft Applications

The report "High Efficiency Centrifugal Compressor for Rotorcraft Applications" documents the work conducted at UTRC under the NRA Contract NNC08CB03C, with cost share 2/3 NASA, and 1/3 UTRC, that has been extended to 4.5 years. The purpose of this effort was to identify key technical barriers to advancing the state-of-the-art of small centrifugal compressor stages; to delineate the measurements required to provide insight into the flow physics of the technical barriers; to design, fabricate, install, and test a state-of-the-art research compressor that is representative of the rear stage of an axial-centrifugal aero-engine; and to acquire detailed aerodynamic performance and research quality data to clarify flow physics and to establish detailed data sets for future application. The design activity centered on meeting the goal set outlined in the NASA solicitation-the design target was to increase efficiency at higher work factor, while also reducing the maximum diameter of the stage. To fit within the existing Small Engine Components Test Facility at NASA Glenn Research Center (GRC) and to facilitate component re-use, certain key design parameters were fixed by UTRC, including impeller tip diameter, impeller rotational speed, and impeller inlet hub and shroud radii. This report describes the design effort of the High Efficiency Centrifugal Compressor stage (HECC) and delineation of measurements, fabrication of the compressor, and the initial tests that were performed. A new High-Efficiency Centrifugal Compressor stage with a very challenging reduction in radius ratio was successfully designed, fabricated and installed at GRC. The testing was successful, with no mechanical problems and the running clearances were achieved without impeller rubs. Overall, measured pressure ratio of 4.68, work factor of 0.81, and at design exit corrected flow rate of 3 lbm/s met the target requirements. Polytropic efficiency of 85.5 percent and stall margin of 7.5 percent were measured at design flow rate and speed. The measured efficiency and stall margin were lower than pre-test CFD predictions by 2.4 percentage points (pt) and 4.5 pt, respectively. Initial impressions from the experimental data indicated that the loss in the efficiency and stall margin can be attributed to a design shortfall in the impeller. However, detailed investigation of experimental data and post-test CFD simulations of higher fidelity than pre-test CFD, and in particular the unsteady CFD simulations and the assessment with a wider range of turbulence models, have indicated that the loss in efficiency is most likely due to the impact of unfavorable unsteady impeller/diffuser interactions induced by diffuser vanes, an impeller/diffuser corrected flow-rate mismatch (and associated incidence levels), and, potentially, flow separation in the radial-to-axial bend. An experimental program with a vaneless diffuser is recommended to evaluate this observation. A subsequent redesign of the diffuser (and the radial-to-axial bend) is also recommended. The diffuser needs to be redesigned to eliminate the mismatching of the impeller and the diffuser, targeting a slightly higher flow capacity. Furthermore, diffuser vanes need to be adjusted to align the incidence angles, to optimize the splitter vane location (both radially and circumferentially), and to minimize the unsteady interactions with the impeller. The radial-to-axial bend needs to be redesigned to eliminate, or at least minimize, the flow separation at the inner wall, and its impact on the flow in the diffuser upstream. Lessons were also learned in terms of CFD methodology and the importance of unsteady CFD simulations for centrifugal compressors was highlighted. Inconsistencies in the implementation of a widely used two-equation turbulence model were identified and corrections are recommended. It was also observed that unsteady simulations for centrifugal compressors require significantly longer integration times than what is current practice in industry.

Centrifugal compressor↗

NASA NTRSDate not supplied

Clifford Neural Operators on Atmospheric Data Influenced Partial Differential Equations

Mathematical representations of the atmosphere are key to forecasting and research tasks across Earth science. Numerically solving the underlying partial differential equations(PDEs) of the atmosphere, however, can be difficult and computationally expensive with numerous trade-offs between computing efficiency and accuracy. Utilizing neural net-works to learn approximations of the PDE solutions from the data can help us model complex phenomena more efficiently than traditional numerical schemes. Here, we have applied Clifford algebra-based neural operators for predicting atmospheric variables. Clifford Fourier neural operators are used with two different backbone architectures, ResNet and UNet, on custom data of U10, V10 and surface pressure as well as U500, V500 and Z500. Clifford Fourier neural operators, coupled with ResNet and UNet architectures, are applied to a key reanalysis dataset. Model performance is initially strong, but we observe increasing errors, resulting in the model becoming highly unstable.

Sujit Roy↗

DOE OSTI2025

DS-TIDE: Harnessing Dynamical Systems for Efficient Time-Independent Differential Equation Solving

Time-Independent Differential Equations (TIDEs) are central to modeling equilibrium behavior across a wide range of scientific and engineering domains, from electrostatics to porous media flow. Conventional numerical solvers offer reliable solutions but incur significant computational costs due to fine-grained discretization and iterative procedures. Machine learning-based approaches address this by replacing iterative solving processes with one-time inference; however, their sophisticated models require extensive training resources that often exceed those of traditional solvers. Consequently, designing a TIDE solver that achieves high accuracy, broad applicability, and exceptional computational efficiency remains a fundamental challenge. In this paper, we propose DS-TIDE, a novel hardware solver that is inspired by, and subsequently leverages, the intrinsic connection between Dynamical Systems (DS) and Differential Equations (DEs) to efficiently and accurately solve TIDEs. DS-TIDE employs a CMOS-compatible DS-based processor, whose physical states evolve under carefully designed DE-driven dynamics and naturally converge to equilibrium -- the solution of the target TIDE -- within ~1µs on a ~1-watt DS-TIDE processor. To enhance expressivity, DS-TIDE incorporates Heterogeneous Dynamics with Temporal Layering (HDTL), which solves TIDEs through a three-stage DS evolution -- conditioning, solving, and decoding -- each governed by specialized dynamics. The entire evolution process is analogous to an infinitely deep neural network temporally unrolled, offering the system the capability of representing complex equations. Furthermore, DS-TIDE is equipped with an on-device DS-DE Auto-Alignment mechanism that dynamically adapts intrinsic hardware dynamics within milliseconds, effectively aligning the system’s dynamics to diverse target DEs. Experimental results across TIDEs from a wide range of scientific and engineering domains demonstrate that DS-TIDE achieves ~10^3× speedup, ~10^5× energy savings, and competitive or superior accuracy compared to state-of-the-art numerical and ML-based solvers.

Liu, Chuan↗

DOE OSTI2024

Physics-Informed Active Learning With Simultaneous Weak-Form Latent Space Dynamics Identification

The parametric greedy latent space dynamics identification (gLaSDI) framework has demonstrated promising potential for accurate and efficient modeling of high-dimensional nonlinear physical systems. However, it remains challenging to handle noisy data. Here, to enhance robustness against noise, we incorporate the weak-form estimation of nonlinear dynamics (WENDy) into gLaSDI. In the proposed weak-form gLaSDI (WgLaSDI) framework, an autoencoder and WENDy are trained simultaneously to discover intrinsic nonlinear latent-space dynamics of high-dimensional data. Compared with the standard sparse identification of nonlinear dynamics (SINDy) employed in gLaSDI, WENDy enables variance reduction and robust latent space discovery, therefore leading to more accurate and efficient reduced-order modeling. Furthermore, the greedy physics-informed active learning in WgLaSDI enables adaptive sampling of optimal training data on the fly for enhanced modeling accuracy. The effectiveness of the proposed framework is demonstrated by modeling various nonlinear dynamical problems, including viscous and inviscid Burgers' equations, time-dependent radial advection, and the Vlasov equation for plasma physics. With data that contains 5%–10% Gaussian white noise, WgLaSDI outperforms gLaSDI by orders of magnitude, achieving 1%–7% relative errors. Compared with the high-fidelity models, WgLaSDI achieves 121 to 1779x speed-up.

97 MATHEMATICS AND COMPUTING↗

DOE OSTI2024

Differentiable vertex fitting for jet flavor tagging

This work explores the use of differentiable programming to integrate domain knowledge, in the form of domain specific software, into neural networks to develop scientific machine learning systems. We propose a differentiable vertex fitting algorithm that estimates the crossing point of multiple curves. In the high energy physics setting, these curves are defined by particle equations of motion and the crossing point represents the origin of particle production. This differentiable vertex fitting algorithm can be seamlessly integrated into neural networks, and we show its utility and efficacy in the high energy physics application of the classification of jets, i.e., collimated streams of particles in particle detectors whose originating parent particle we aim to classify. We demonstrate how differentiable vertex fitting can be integrated into larger transformer-based models for jet flavor tagging and show improvements in heavy flavor jet classification when compared to baseline models. Published by the American Physical Society 2024

Smith, Rachel E. C. (ORCID:0000000335851262)↗

NASA NTRSDate not supplied

Open-source Numerical Modeling of Solidification Cracking Susceptibility: Application to Refractory Alloy Systems

Introduction. Alloys such as aluminum, nickel-base, and austenitic stainless steels are susceptible to solidification cracking during welding and 3D printing. Compositional optimization is one method used to effectively mitigate solidification cracking of those alloy systems. With the surge in hypersonic and in-space propulsion activities, refractory metals (Nb, Mo, Ta, W, and Re) and their alloy derivatives are increasing in importance due to their extreme high melting point and retention of high-temperature strength; however, their chemistry was most typically optimized to promote ductility during mechanical operations such as drawing and forming. Welding of such alloys has been a challenge due to a number of issues including solidification cracking, atmospheric contamination (O, C, and N), as well as a shift in ductile-to-brittle transition to higher temperature following grain growth induced by welding. Compositional optimization of refractory alloys for solidification cracking resistance in particular is desirable as their usage increases with the advent of advanced manufacturing methods such as 3D printing. This work evaluates the effect of compositional variation in refractory metal systems on the solidification cracking susceptibility with the goals of optimizing existing alloys and joining process techniques, and formulating new alloys with increased solidification cracking resistance. Experimental Procedures. A python code was developed in a Jupyter notebook environment (Michael and Sowards, 2023) to facilitate the calculation of crack susceptibility index proposed by Kou (2015). Composition is entered as a single point, or as a 1-D or 2-D array. The notebook calls pycalphad (Otis and Liu, 2017 and Bocklund et al, 2020) to calculate the evolution of fraction solid as a function of temperature (under either Scheil or equilibrium assumptions) and then evaluates steepness of the fraction solid curve near the terminal stage of solidification to predict solidification cracking resistance. Open source thermodynamic databases available at online repositories are used (van de Walle). The process is setup in an automated fashion to generate plots that show variation in solidification cracking susceptibility according to composition on 1-D line plots or 2-D contour plots. The Jupyter notebook and crack susceptibility algorithm was also integrated with a widely used commercial CALPHAD code for validation and alloy exploration. Results and Discussion. The crack susceptibility model was first validated against a series of refractory alloy compositions evaluated in past work which utilized a specialized Varestraint test built inside a vacuum chamber environment (Lessman and Gold, 1971). The alloys tested in the Varestraint apparatus included T-111 (Ta-8W-2Hf), ASTAR-811C (Ta-8W-1Re-0.7Hf-0.025C), FS-85 (Nb-27Ta-10W-1Zr), T-222 (Ta-9.6W-2.4Hf-0.01C), Ta-10W, B-66 (Nb-5Mo-5V-1Zr), and SCb-291 (Nb-10W-10Ta). The initial test of the model showed a strong correlation with empirical Varestraint data, i.e., a Spearman rank correlation between model predictions and hot cracking measurements was observed to be greater than 0.8. Following the validation, a set of refractory metal binary mixtures was investigated to evaluate sensitivity of Nb, Mo, W, and Ta to C, N, and O content. A series of plots were produced that suggest ppmw ranges of C, N, and O where solidification cracking increases significantly and reaches a maximum. Also comparative ranking of each primary refractory metal to each interstitial was produced. For example C produces greater cracking response in Mo whereas O produces greater cracking response in Ta and Nb. Such compositional values have utility in setting limits on pickup of these interstitial elements during welding and printing rather than using a one-size-fits-all approach. Furthermore, the results have use in determining additive powder recycling requirements, which is especially pertinent for refractory metal powders due to their high cost compared to conventional alloys. Another application created thousands of hypothetical alloys within the nominal specified composition range of two widely used refractory alloys C103 (Nb-10Hf-1Ti) and TZM (Mo-0.5Ti-0.1Zr). The cracking index was calculated for the alloys and results were fed into machine learning regression techniques including Multiple Linear Regression, Ridge Regression, and Lasso Regression to determine relative potency each alloying element had on computed solidification cracking index. A series of linear equations were produced that relate composition of C103 and TZM to solidification cracking index. The crack susceptibility of C103 for example is described by an equation of the form: cracking index ~ O + 0.667*C + 0.635*N + 0.00037*Ta – 0.0008*Hf (in wt.%) From that equation, it is clear that O has strong propensity to induce solidification cracking. Interestingly, Hf is shown to reduce calculated cracking response. Finally, realizing the potential of this method to discover new refractory alloy formulations across the period table that have low solidification cracking sensitivity, the code was applied to new untested alloy systems including W-Zr-C, W-Ta-C, and others. Conclusions. In summary, an open source numerical method has been developed using Python code to calculate Kou’s crack susceptibility index. The method was applied to refractory metals which are inherently difficult to study from a weldability testing standpoint since inert shielding gas is not sufficient and welding is typically done in vacuum, especially in light of findings presented here where oxygen has profound influence on solidification cracking. This work revealed the effect of compositional variations on a series of refractory metals and showed the framework defined here will be useful in 1) the development of new alloys that have improved weldability and 3D printability, 2) placing compositional limits on existing alloys, and 3) ensuring adequate controls of manufacturing processes such as 3D printing where powder reuse is critical. Keywords. pycalphad; Python; refractory metals; solidification cracking. References. B. Bocklund et. al. (2020) http://doi.org/10.5281/zenodo.3630657. S. Kou. (2015) https://doi.org/10.1016/j.actamat.2015.01.034. G.G. Lessmann and R.E. Gold. Welding Journal, issue 1, pp. 1-s – 8-s (1971). F.N. Michael and J.W. Sowards. NASA/TM-20230002218 (2023). R. Otis and Z.-K. Liu. (2017) http://doi.org/10.5334/jors.140. A. Van de Wallle et. al. (2018) https://doi.org/10.1016/j.calphad.2018.04.003.

pycalphad↗

DOE OSTI2025

Kinetic Deep Learning v0.1

Here, we present a method that uses protein levels to predict times series of metabolite concentrations. Understanding this type of pathway dynamics is important in order to predict the behavior of the pathway and, more pragmatically, to be able to design biological systems (such as strains bioengineered to produce chemical products) reliably. Typically, for this purpose, kinetic models consisting of differential equations based on the Michaelis-Menten dynamics have been used in the past. However, these methods can rarely produce good fits to measured data time series. Possibly, this happens because the kinetic constants are unknown or are different from the ones measured in vivo, or perhaps because Michaelis-Menten dynamics is not a satisfactory description. In order to improve the predictive nature of these kinetic models we have eliminated the Michaelis-Menten description of pathway dynamics and we have substituted it by algorithms that automatically learn these dynamics from previously obtained metabolomics and proteomics data using machine learning approaches. Specifically, kinetic deep learning uses deep learning to map proteomics time series to metabolite concentration time series, instead of learning the first metabolite derivative and integrating in (as in the first version of kinetic learning). This approach is shown to provide good to excellent results with a data set specifically collected for this purpose.

Garcia Martin, Hector [Joint BioEnergy Institute (↗

DOE OSTI2026

Machine Learning Approach to Modeling of Neutral Particles Transport in Plasma

A propagator‐based approach is investigated for Monte‐Carlo (MC) modeling of neutral particle transport in fusion boundary plasmas. The propagator is based on a Green's function for the neutral kinetic equation, which depends on the plasma profiles. A neural network (NN)‐based model for the propagator provides a fast and accurate solution for the neutral distribution function in plasma. Preliminary results from a small 1D test problem look encouraging. The proposed approach, a propagator‐based NN model for neutral transport in plasma, has potential for generalization to higher dimensions and efficient coupling with plasma models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2026

Leveraging machine learning to enhance aerosol classification using Single-Particle Mass Spectrometry

Advancing automated classification of atmospheric aerosols from Single-Particle Mass Spectrometry (SPMS) data remains challenging due to overlapping ion signatures, compositional diversity, and limited labeled data. This study evaluates supervised and semi-supervised learning frameworks to enhance aerosol identification by jointly leveraging labeled and unlabeled spectra. Four models were compared: a supervised Support Vector Machine (SVM), a self-training SVM, a stacked autoencoder classifier, and a stacked autoencoder trained using a temporal-ensembling Mean Teacher approach. All models achieved high and stable accuracies (90.0 %–91.1 %), surpassing previous results on the same dataset (87 %) and matching the performance of state-of-the-art deep learning methods. Despite small global metric differences (≤ 1 %), semi-supervised variants yielded up to 5 %–10 % improvements for compositionally rare particle types – such as soot (0.77 % of spectra, F1-score: 0.93–0.97) and hazelnut pollen (0.98 % of spectra, F1-score: 0.97–1.00) – equating to roughly ∼ 187 additional correctly classified spectra. These gains are scientifically significant, as such rare particles exert disproportionate influence on radiative absorption and ice nucleation processes; their improved detection reduces modeled uncertainties in aerosol absorption optical depth and mixed-phase cloud ice nucleation rates. The models' residual misclassifications (≈ 9 %) largely arise from true spectral overlap among chemically adjacent species (e.g., Na- vs. K-feldspar, coated vs. uncoated feldspars), reflecting physical compositional continuity rather than algorithmic error. Collectively, these findings demonstrate that leveraging unlabeled data to learn robust spectral representations and refine classification enhances both fidelity and interpretability, bridging data-driven analysis with aerosol–climate process understanding.

54 ENVIRONMENTAL SCIENCES↗