SEARCH · Search NASA

Results for “Exploratory Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Estimation of sea surface temperature from remote sensing in the 11to 13-micron window region

The Nimbus 3 and 4 Iris spectral data in the 11- to 13-micron water vapor window region are analyzed to determine the sea surface temperature (SST). The high spectral resolution data of Iris are averaged over approximately 1-micron-wide intervals to simulate channels of a radiometer to measure the SST. In the present exploratory study, three such channels in the 775- to 960-per cm (12.9-10.5 micron) region are utilized to measure the SST over cloud-free oceans. However, two of these channels are sufficient in routine SST determination. The differential absorption properties of water vapor in the two channels make it possible to determine the water vapor absorption correction without detailed knowledge of the vertical profiles of temperature and water vapor. The feasibility of determining the SST is demonstrated globally with Nimbus 3 data, where cloud-free areas can be selected with the help of albedo data from the medium-resolution infrared radiometer experiment on board the same satellite. The SST derived from this technique agrees with the measurements made by ships to about 1 C.-

Prabhakara, C.↗

NASA NTRS1976

Optimal periodic proof test based on cost-effective and reliability criteria

An exploratory study for the optimization of periodic proof tests for fatigue-critical structures is presented. The optimal proof load level and the optimal number of periodic proof tests are determined by minimizing the total expected (statistical average) cost, while the constraint on the allowable level of structural reliability is satisfied. The total expected cost consists of the expected cost of proof tests, the expected cost of structures destroyed by proof tests, and the expected cost of structural failure in service. It is demonstrated by numerical examples that significant cost saving and reliability improvement for fatigue-critical structures can be achieved by the application of the optimal periodic proof test. The present study is relevant to the establishment of optimal maintenance procedures for fatigue-critical structures.

Yang, J.-N.↗

NASA NTRS1977

On the role of minicomputers in structural design

Results are presented of exploratory studies on the use of a minicomputer in conjunction with large-scale computers to perform structural design tasks, including data and program management, use of interactive graphics, and computations for structural analysis and design. An assessment is made of minicomputer use for the structural model definition and checking and for interpreting results. Included are results of computational experiments demonstrating the advantages of using both a minicomputer and a large computer to solve a large aircraft structural design problem.

Storaasli, O. O.↗

NASA NTRS1977

Ultraviolet spectrometer experiment for the Voyager mission

An objective grating spectrometer covering the wavelength range of 500 to 1700 A with a 10-A resolution is employed for the Voyager ultraviolet spectrometer experiment. In determining the composition and structure of the atmospheres of Saturn, Jupiter and several satellites, the ultraviolet spectrometer will rely on airglow mode observations to measure radiation from the atmospheres due to resonant scattering of solar flux, and the occultation mode for assessments of the atmospheric extinction of solar or stellar radiation as the spacecraft enters shadow zones. Since it is capable of prolonged stellar observations in the 500 to 1000 A wavelength range, the spectrometer is expected to make important contributions to exploratory studies of UV sources.

Broadfoot, A. L.↗

NASA NTRS1978

A methodology for selecting optimum organizations for space communities

This paper suggests that a methodology exists for selecting optimum organizations for future space communities of various sizes and purposes. Results of an exploratory study to identify an optimum hypothetical organizational structure for a large earth-orbiting multidisciplinary research and applications (R&A) Space Base manned by a mixed crew of technologists are presented. Since such a facility does not presently exist, in situ empirical testing was not possible. Study activity was, therefore, concerned with the identification of a desired organizational structural model rather than the empirical testing of it. The principal finding of this research was that a four-level project type 'total matrix' model will optimize the effectiveness of Space Base technologists. An overall conclusion which can be reached from the research is that application of this methodology, or portions of it, may provide planning insights for the formal organizations which will be needed during the Space Industrialization Age.

Ragusa, J. M.↗

NASA NTRS1978

Controlled vapor growth of small particles of Pd and Fe on thin Al2O3 substrates

An exploratory study, dealing with the preparation of well-defined particulate metal deposits that can be used in model studies of catalytic reactions, was performed. Small metal particles of Fe and Pd were grown in situ in an electron microscope by vapor deposition onto different phase of electron transparent alumina substrates. The results show that characteristic properties of the deposits, such as particle density, size distribution, habit, and orientation, are strongly dependent on the cleanliness, phase, and crystallographic orientation of the alumina substrate; also, the deposition conditions can be chosen in such a way as to reproducibly manipulate the overall deposit structure.

Poppa, H.↗

NASA NTRS1979

A simplified rotor system mathematical model for piloted flight dynamics simulation

The model was developed for real-time pilot-in-the-loop investigation of helicopter flying qualities. The mathematical model included the tip-path plane dynamics and several primary rotor design parameters, such as flapping hinge restraint, flapping hinge offset, blade Lock number, and pitch-flap coupling. The model was used in several exploratory studies of the flying qualities of helicopters with a variety of rotor systems. The basic assumptions used and the major steps involved in the development of the set of equations listed are described. The equations consisted of the tip-path plane dynamic equation, the equations for the main rotor forces and moments, and the equation for control phasing required to achieve decoupling in pitch and roll due to cyclic inputs.

Chen, R. T. N.↗

NASA NTRS1979

The infrared spectra of Uranus, Neptune, and Titan from 0.8 to 2.5 microns

The paper combines the results of two projects that significantly augment previous studies: exploratory IR spectroscopic observations of Uranus, Neptune, and Titan using a 4-m telescope; and new long-path laboratory comparison spectra of methane at abundances appropriate for these planetary spectra. The observations of these previously unexplored spectral regimes provide new insights into the composition and structures of these atmospheres. The spectra of Uranus, Neptune, and Titan are discussed and analyzed from several complementary points of view. A number of specific topics are discussed in detail: methane abundance determinations, limitations in using the 3nu3 CH4 band at high abundances, upper limits to a number of molecules, implications from the pressure-induced spectrum of H2, and consequences of Rayleigh scattering in Uranus's upper atmosphere.

Fink, U.↗

NASA NTRS1981

Transonic flutter and gust-response tests and analyses of a wind-tunnel model of a torsion free wing airplane

An exploratory study of a 1/5.5 size, complete airplane version of a torsion free wing (TFW) fighter aircraft was conducted. The TFW consisted of a wing/boom/canard assembly on each fuselage side that was interconnected by a common pivot shaft so that the TFW could rotate freely in pitch. The effect of the TFW was evaluated by comparing data obtained with the TFW free and the TFW locked to the fuselage. With the model mounted on cables to simulate an airplane free flying condition, flutter boundaries were measured at Mach number (M) from 0.85 to 1.0 and gust responses at M = 0.65 and 0.90. The critical flutter mode for the TFW free configuration was found experimentally to occur at M = 0.95 and had the rigid TFW pitch mode as its apparent aerodynamic driver.

Ruhlin, C. L.↗

NASA NTRS1980

Numerical solutions of transonic flows by parametric differentiation and integral equation techniques

The paper discusses results of an exploratory study of the advantages obtained by combining integral equation methods with the method of parametric differentiation in the treatment of transonic flow problems. In the proposed method, the nonlinear unsteady transonic flow equation for small perturbations is transformed into a linear equation by the use of the method of parametric differentiation. The linear equation is split into a pair of weakly coupled partial differential equations by writing the transformed perturbation potential as the sum of a steady component and an unsteady component. The solution of the steady equation as an integral equation is based on Ogana's treatment (1978). As a test case, the formulation is applied to predict the steady transonic flow over a nonlifting parabolic-arc airfoil.

Sivaneri, N. T.↗

NASA NTRS1984

PAN AIR prediction of NASA Ames 12-foot pressure wind-tunnel interference on a fighter configuration

Models tested in the NASA Ames 12-Foot Pressure Wind Tunnel over an angle of attack range from 0 deg to 90 deg are mounted on a floor strut that protrudes from a fairly large support bump. In high-angle-of-attack tests (angle of attack = 40 deg to 90 deg), for which the floor support was originally designed, the effects of the flow angularities produced by the bump are often negligible. This is not so for low-angle-of-attack tests (0 deg to 40 deg). Since there are no standard means for correcting test data for this bump effect, low-angle-of-attack testing with the bump is not recommended by the Ames wind-tunnel staff. This paper presents an exploratory study of a technique for correcting balance forces and experimental pressures for combined wall and bump effects. This is done by modeling the aircraft, wind-tunngl walls, and bump, with PAN AIR. The wall-and-bump-induced increments in the lift coefficient and pitching-moment coefficient predicted by PAN AIR are compared with increments obtained from the Ames 12-foot tunnel with the bump and an 8 x 12 low speed wind tunnel which has no bump.

Snyder, L. D.↗

NASA NTRS1985

The Moist Available Energy of a Conditionally Unstable Atmosphere

Two simple methods for computing the moist available energy for cases in which the total number of parcels is fairly small are discussed. The first is a swapping routine that finds the reference state by exchanging parcels whenever the swap reduces the total enthalpy. However, it can be proved by contrived example that the swapping algorithm does not always find the true reference state. A second brute force routine actually examines all possible arrangements of the parcels and chooses the one with the smallest moist enthalpy. At present, both routines allow only horizontally homogeneous reference states. In an exploratory study, the swapping routine was used to find MAE and reference state for a time sequence of GATE soundings, all of which are conditionally unstable. In spot checks, the brute force routine always agreed with the swapper. Results show that in passing from the given state of the reference state the lowest three hundred mb of the atmosphere typically exchanges places with the 300 mb above it. The reference state then contains a dry warm layer near the surface, but a supersaturated but cool layer in the middle troposphere. The upper portion of the sounding is not modified in passing from the given state to the reference state.

Randall, D.↗

NASA NTRS1984

Space Station accommodation engineering for Life Sciences Research Facilities

Exploratory studies conducted by NASA Marshall Space Flight Center and several contractors in connection with defining the design requirements, parameters, and tradeoffs of the Life Sciences Research Facilities for nonhuman test subjects aboard the Space Station are reviewed. The major system discriminators which determine the size of the accommodation system are identified, along with a number of mission options. Moreover, characteristics of several vivarium concepts are summarized, focusing on the cost, size, variable-g capability, and the number of specimens accommodated. Finally, the objectives of the phase B studies of the Space Station Laboratory, which are planned for FY85, are described.

Hilchey, J.↗

NASA NTRS1985

Matrix resin development at NASA Langley Research Center

The polymer program at NASA Langley Research Center involves exploratory studies in polymer science. These include the synthesis of novel polymers and their characterization. Polymer synthesis programs involve the development of novel thermoplastics, pseudothermoplastics, and thermosets. Recent investigations have led to the development of more easily processable polyimides, solvent-resistant polysulfones and polyphenylquinoxalines, and tougher high and intermediate-temperature polymers. Characterization efforts have included high-pressure liquid chromatography methodology, the development of toughness tests for fiber-reinforced composites, a study of electrical properties of metal-ion-filled polyimides, and a study of the mutagenicity of aromatic diamines. Also the mechanism of cure/degradation of experimental polymers has been studied by rheology, mechanical behavior, separation techniques and spectroscopy. Some of these programs have involved the degradation crosslinking of alkyl-containing polyimides, the separation and identification of crosslinked phenylquinoxalines, the rheological behavior of hot-melt polyimides, and the elucidation of the cure of norbornene endcapped imides.

St.clair, T. L.↗

NASA NTRS1985

Analysis of atomic thermospheric nitrogen density

A NASA grant provided support for a research project at Augsbury College, Minneapolis, Minnesota for the analysis of atomic nitrogen density data obtained by the Neutral Atmospheric Composition Spectrometer (NACS) on board the Dynamics Explorer-2 satellite. Initial funding was for an exploratory study of the feasibility of obtaining ambient densities of N from source densities of NO. Funding was continued under the Dynamics Explorer Guest Investigator Program when initial studies indicated probable success in obtaining such ambient densities. The major scientific focus of the later work was to be to characterize the behavior of N densities at high latitudes.

Engebretson, M. J.↗

NASA NTRS1986

Modified Petri net model sensitivity to workload manipulations

Modified Petri Nets (MPNs) are investigated as a workload modeling tool. The results of an exploratory study of the sensitivity of MPNs to work load manipulations in a dual task are described. Petri nets have been used to represent systems with asynchronous, concurrent and parallel activities (Peterson, 1981). These characteristics led some researchers to suggest the use of Petri nets in workload modeling where concurrent and parallel activities are common. Petri nets are represented by places and transitions. In the workload application, places represent operator activities and transitions represent events. MPNs have been used to formally represent task events and activities of a human operator in a man-machine system. Some descriptive applications demonstrate the usefulness of MPNs in the formal representation of systems. It is the general hypothesis herein that in addition to descriptive applications, MPNs may be useful for workload estimation and prediction. The results are reported of the first of a series of experiments designed to develop and test a MPN system of workload estimation and prediction. This first experiment is a screening test of MPN model general sensitivity to changes in workload. Positive results from this experiment will justify the more complicated analyses and techniques necessary for developing a workload prediction system.

White, S. A.↗

NASA NTRS1990

An engineering approach to automatic programming

An exploratory study of the automatic generation and optimization of symbolic programs using DECOM - a prototypical requirement specification model implemented in pure LISP was undertaken. It was concluded, on the basis of this study, that symbolic processing languages such as LISP can support a style of programming based upon formal transformation and dependent upon the expression of constraints in an object-oriented environment. Such languages can represent all aspects of the software generation process (including heuristic algorithms for effecting parallel search) as dynamic processes since data and program are represented in a uniform format.

Rubin, Stuart H.↗

NASA NTRS1990

Identification challenges for large space structures

The paper examines the on-orbit modal identification of large space structures, stressing the importance of planning and experience, in preparation for the Space Station Structural Characterization Experiment (SSSCE) for the Space Station Freedom. The necessary information to foresee and overcome practical difficulties is considered in connection with seven key factors, including test objectives, dynamic complexity of the structure, data quality, extent of exploratory studies, availability and understanding of software tools, experience with similar problems, and pretest analytical conditions. These factors affect identification success in ground tests. Comparisons with similar ground tests of assembled systems are discussed, showing that the constraints of space tests make these factors more significant. The absence of data and experiences relating to on-orbit modal identification testing is shown to make identification a uniquely mathematical problem, although all spacecraft are constructed and verified by proven engineering methods.

Pappa, Richard S.↗