SEARCH · Search NASA

Results for “FUSELAGES - BENDING MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1995

Airfoil modification effects on subsonic and transonic pressure distributions and performance for the EA-6B airplane

Longitudinal characteristics and wing-section pressure distributions are compared for the EA-6B airplane with and without airfoil modifications. The airfoil modifications were designed to increase low-speed maximum lift for maneuvering, while having a minimal effect on transonic performance. Section contour changes were confined to the leading-edge slat and trailing-edge flap regions of the wing. Experimental data are analyzed from tests in the Langley 16-Foot Transonic Tunnel on the baseline and two modified wing-fuselage configurations with the slats and flaps in their retracted positions. Wing modification effects on subsonic and transonic performance are seen in wing-section pressure distributions of the various configurations at similar lift coefficients. The modified-wing configurations produced maximum lift coefficients which exceeded those of the baseline configuration at low-speed Mach numbers (0.300 and 0.400). This benefit was related to the behavior of the wing upper surface leading-edge suction peak and the behavior of the trailing-edge pressure. At transonic Mach numbers (0.725 to 0.900), the wing modifications produced a somewhat stronger nose-down pitching moment, a slightly higher drag at low-lift levels, and a lower drag at higher lift levels.

Allison, Dennis O.↗

NASA NTRS1957

A Fuselage Addition to Delay Drag-Rise Mach Number of Subsonic Airplanes at Lifting Conditions

The addition of fuselage volume, concentrated on top of the forward portion of the fuselage, for the purpose of delaying the drag-rise Mach number of subsonic airplanes at lifting conditions is investigated. The additions have been designed on the basis of the area rule and other important considerations to provide greater practicability of application compared with shapings previously investigated. The addition delayed the drag-rise Mach number by an increment of approximately 0.03 for a configuration having a wing with moderate thickness and 35 deg of sweepback at a lift coefficient of 0.3. A lesser delay was obtained for a configuration with a thicker wing. The additions increase the nonlinearities of the variations of pitching moment with lift,

Whitcomb, Richard T.↗

NASA NTRS1984

Results of the first complete static calibration of the RSRA rotor-load-measurement system

The compound Rotor System Research Aircraft (RSRA) is designed to make high-accuracy, simultaneous measurements of all rotor forces and moments in flight. Physical calibration of the rotor force- and moment-measurement system when installed in the aircraft is required to account for known errors and to ensure that measurement-system accuracy is traceable to the National Bureau of Standards. The first static calibration and associated analysis have been completed with good results. Hysteresis was a potential cause of static calibration errors, but was found to be negligible in flight compared to full-scale loads, and analytical methods have been devised to eliminate hysteresis effects on calibration data. Flight tests confirmed that the calibrated rotor-load-measurement system performs as expected in flight and that it can dependably make direct measurements of fuselage vertical drag in hover.

Acree, C. W., Jr.↗

NASA NTRS1990

Transonic wind tunnel test of a 14 percent thick oblique wing

An experimental investigation was conducted at the ARC 11- by 11-Foot Transonic Wind Tunnel as part of the Oblique Wing Research Aircraft Program to study the aerodynamic performance and stability characteristics of a 0.087-scale model of an F-8 airplane fitted with an oblique wing designed by Rockwell International. The 10.3 aspect ratio, straight-tapered wing of 0.14 thickness/chord ratio was tested at two different mounting heights above the fuselage. Additional tests were conducted to assess low-speed behavior with and without flaps, aileron effectiveness at representative flight conditions, and transonic drag divergence with 0 degree wing sweep. Longitudinal stability data were obtained at sweep angles of 0, 30, 45, 60, and 65 degrees, at Mach numbers ranging from 0.25 to 1.40. Test Reynolds numbers varied from 3.2 to 6.6 x 10 exp 6/ft. and angle of attack ranged from -5 to +18 degrees. Most data were taken at zero sideslip, but a few runs were at sideslip angles of +/- 5 degrees. The raised wing position proved detrimental overall, although side force and yawing moment were reduced at some conditions. Maximum lift coefficient with the flaps deflected was found to fall short of the value predicted in the preliminary design document. The performance and trim characteristics of the present wing are generally inferior to those obtained for a previously tested wing designed at ARC.

Kennelly, Robert A., Jr.↗

NASA NTRS2000

Electromagnetic Field Penetration Studies

A numerical method is presented to determine electromagnetic shielding effectiveness of rectangular enclosure with apertures on its wall used for input and output connections, control panels, visual-access windows, ventilation panels, etc. Expressing EM fields in terms of cavity Green's function inside the enclosure and the free space Green's function outside the enclosure, integral equations with aperture tangential electric fields as unknown variables are obtained by enforcing the continuity of tangential electric and magnetic fields across the apertures. Using the Method of Moments, the integral equations are solved for unknown aperture fields. From these aperture fields, the EM field inside a rectangular enclosure due to external electromagnetic sources are determined. Numerical results on electric field shielding of a rectangular cavity with a thin rectangular slot obtained using the present method are compared with the results obtained using simple transmission line technique for code validation. The present technique is applied to determine field penetration inside a Boeing-757 by approximating its passenger cabin as a rectangular cavity filled with a homogeneous medium and its passenger windows by rectangular apertures. Preliminary results for, two windows, one on each side of fuselage were considered. Numerical results for Boeing-757 at frequencies 26 MHz, 171-175 MHz, and 428-432 MHz are presented.

Deshpande, M.D.↗

NASA NTRS1957

Effect of Ground Proximity on Aerodynamic Characteristics of Two Horizontal-Attitude Jet Vertical-Take-Off-and-Landing Airplane Models

An investigation has been made to study the effect of ground proximity on the aerodynamic characteristics of two jet vertical-take-off-and-landing airplane models in which the fuselage remains in a horizontal attitude for the take-off and landing. The first model (called the tilt-wing model) had a tilting wing-engine assembly which was set at 90 degree incidence for the take-off and landing. The second model (called the deflected-jet model) had a cascade of retractable turning vanes to deflect the exhaust of the horizontally mounted Jet engines downward for vertical take-off and landing while the entire model remained in a horizontal attitude. With the models at various heights above the ground in the take-off and landing configuration, the llft, drag, and pitching moment were measured and tuft surveys were made to determine the flow field caused by the Jet exhaust. The tilt-wing model experienced a loss of lift of less than 3 percent near the ground. The deflected-Jet model, however, suffered losses in lift as high as 45 percent near the ground because of a low pressure region under the model caused by the entrainment of air by the jet exhaust as it spread out along the ground. This loss in lift for the deflected Jet configuration could probably be reduced to less than 5 percent by the use of a longer landing gear and a high wing location.

Newsom, William A , Jr↗

NASA NTRS1960

Effect of Ground Proximity on Aerodynamic Characteristics of Two Horizontal-Attitude Jet Vertical-Take-Off-and-Landing Airplane Models

An investigation has been made to study the effect of ground proximity on the aerodynamic characteristics of two jet vertical-take-off-and-landing airplane models in which the fuselage remains in a horizontal attitude for the take-off and landing. The first model (called the tilt-wing model) had a tilting wing-engine assembly which was set at 90 deg incidence for the take-off and landing. The second model, called the deflected-jet model) had a cascade of retractable turning vanes to deflect the exhaust of the horizontally mounted jet engines downward for vertical take-off and landing while the entire model remained in a horizontal attitude. With the models at various heights above the ground in the take-off and landing configuration, the lift, drag, and pitching moment were measured and tuft surveys were made to determine the flow field caused by the jet exhaust. The tilt-wing model experienced a loss of lift of less than 3 percent near the ground. The deflected-jet model, however, suffered losses in lift as high as 45 percent near the ground because of a low pressure region under the model caused by the entrainment of air by the jet exhaust as it spread out along the ground. This loss in lift for the deflected-jet configuration could probably be reduced to less than 5 percent by the use of a longer landing gear and a high wing location.

Newsom, William A., Jr.↗

NASA NTRS1959

Subsonic Aerodynamic Characteristics of an Airplane Configuration with a 63 deg Sweptback Wing and Twin-Boom Tails

A wind-tunnel investigation has been conducted to determine the effects of an unconventional tail arrangement on the subsonic static longitudinal and lateral stability characteristics of a model having a 63 deg sweptback wing of aspect ratio 3.5 and a fuselage. Tail booms, extending rearward from approximately the midsemispan of each wing panel, supported independent tail assemblies well outboard of the usual position at the rear of the fuselage. The horizontal-tail surfaces had the leading edge swept back 45 deg and an aspect ratio of 2.4. The vertical tail surfaces were geometrically similar to one panel of the horizontal tail. For comparative purposes, the wing-body combination was also tested with conventional fuselage-mounted tail surfaces. The wind-tunnel tests were conducted at Mach numbers from 0.25 to 0.95 with a Reynolds number of 2,000,000, at a Mach number of 0.46 with a Reynolds number of 3,500,000, and at a Mach number of 0.20 with a Reynolds number of 7,000,000. The results of the investigation indicate that longitudinal stability existed to considerably higher lift coefficients for the outboard tail configuration than for the configuration with conventional tail. Wing fences were necessary with both configurations for the elimination of sudden changes in longitudinal stability at lift coefficients between 0.3 and 0.5. Sideslip angles up to 15 deg had only small effects upon the pitching-moment characteristics of the outboard tail configuration. There was an increase in the directional stability for the outboard tail configuration at the higher angles of attack as opposed to a decrease for the conventional tail configuration at most of the Mach numbers and Reynolds numbers of this investigation. The dihedral effect increased rapidly with increasing angle of attack for both the outboard and the conventional tail configurations but the increase was greater for the outboard tail configuration. The data indicate that the outboard tail is an effective roll control.

Savage, Howard F.↗

NASA NTRS1950

Aerodynamic Characteristics of NACA RM-10 Missile in 8- by 6-foot Supersonic Wind Tunnel at Mach Numbers from 1.49 to 1.98 II : Presentation and Analysis of Force Measurements

Experimental investigation of aerodynamic forces acting on body of revolution (NACA RM-10 missile) with and without stabilizing fins was conducted at Mach numbers from 1.49 to 1.98 at angles of attack from 0 to 9 degrees and at Reynolds number of approximately 30,000,000. Comparison of experimental lift, drag, and pitching-moment coefficients and center of pressure location for body alone is made with linearized potential theory and a semiempirical method. Results indicate that aerodynamic characteristics were predicted more accurately by semiempirical method than by potential theory. Breakdown of measured drag coefficients into components of friction, pressure, and base-pressure drag is presented for body alone at zero angle of attack.

TAIL-BODY COMBINATIONS - MISSILES↗

NASA NTRS1972

Wind tunnel investigation of a large scale 35 deg swept wing jet transport model with an external blowing triple slotted flap

An investigation was conducted to determine the aerodynamic characteristics of a large-scale subsonic jet transport model with an externally jet-augmented flap system that would augment lift and provide direct-lift control. The model had a 35 deg swept wing of aspect ratio 7.82 and two side-by-side engines mounted on a single pylon under each wing close to the fuselage. The lift of the flap system was augmented by jet engine exhaust impingement on the triple-slotted flap surfaces. The rearmost flap provided direct lift control. Results were obtained for several combinations of flap deflections at gross thrust coefficients from 0 to 2.0. Three-component longitudinal data are presented with four engines operating. Limited longitudinal and lateral data are presented for asymmetric and symmetric thrust conditions with three engines operating. For the same overall flap deflection, lift coefficient and maximum lift coefficient were improved 13 and 7 percent compared to coefficients obtained with a double-slotted flap configuration. A maximum lift coefficient of 6.3 was obtained at a gross thrust coefficient of 2.0. At the same flap deflection lateral and directional trim moment requirements with an engine inoperative were reduced 55 and 33 percent, respectively, compared to those with the engines located farther outboard on the wing. Trim moment requirements in pitch were also reduced significantly. However, pitching-moment instability occurred and increased with gross thrust coefficient.

Aoyagi, K.↗

NASA NTRS1993

Subsonic aerodynamic characteristics of a proposed advanced manned launch system orbiter configuration

The Advanced Manned Launch System is a proposed near-term technology, two-stage, fully reusable launch system that consists of an unmanned glide-back booster and a manned orbiter. An orbiter model that featured a large fuselage and an aft delta wing with tip fins was tested in the Langley 7- by 10-Foot High-Speed Tunnel. A crew cabin, large payload fairing, and crew access tunnel were mounted on the upper body. The results of the investigation indicated that the configuration was longitudinally stable to an angle of attack of about 6 deg about a center-of-gravity position of 0.7 body length. The model had an untrimmed lift-drag ratio of 6.6, but could not be trimmed at positive lift. The orbiter model was also directionally unstable. The payload fairing was responsible for about half the instability. The tip-fin controllers, which are designed as active controls to produce artificial directional stability, were effective in producing yawing moment, but sizable adverse rolling moment occurred at angles of attack above 6 deg. Differential deflection of the elevon surfaces was effective in producing rolling moment with only small values of adverse yawing moment.

Ware, George M.↗

NASA NTRS1962

Jet Interference Effects on a Model of a Single-Engine Four Jet V/STOL Airplane at Mach Numbers from 0.60 to 1.00

An investigation was conducted in the Langley 16-foot transonic tunnel to determine the interference from four exhaust jets on the aerodynamic characteristics of a model of a V/STOL airplane. The single- engine four-jet turbofan power plant of the airplane was simulated by inducing tunnel airflow through two large side inlets and injecting the decomposition products of hydrogen peroxide into the internal flow. The heated gas mixture was exhausted through four nozzles located on the sides of the fuselage under the wing, two near the wing leading edge and two forward of the trailing edge; the nozzles were deflected downward 1.5 deg and outward 5.0 deg to simulate cruise conditions. The wing of the model was a clipped delta with leading-edge sweep of 40 deg, aspect ratio of 3.06, taper ratio of 0.218, thickness-chord ratio of 0.09 at the root and 0.07 at the tip, and 10 deg negative dihedral. Aerodynamic and longitudinal stability coefficients were obtained for the model with the tail removed, and for horizontal-tail incidences of 0 deg and -5 deg. Data were obtained at Mach numbers from 0.60 to 1.00, angles of attack from 0 deg to 12 deg, and with jet total-pressure ratios up to 3.1. Jet operation generally caused a decrease in lift, an increase in pitching-moment coefficient, and a decrease in longitudinal stability at subsonic speeds. The jet interference effects on drag were detrimental at a Mach number of 0.60 and favorable at higher speeds for cruising-flight attitudes.

Schmeer, James W.↗

NASA NTRS2024

Computational Analysis of the X-57 Maxwell Airplane, the Landing Configuration with High-Lift Blowing and Aileron Deflections (Preliminary Fuselage)

The X-57 Maxwell is an all-electric airplane with a distributed electric propulsion system used for a high-lift system at takeoff and landing conditions. The Kestrel and USM3D flow solvers were used at NASA Langley to investigate the performance of the X-57 Maxwell in the development of an aerodynamic database. The configuration investigated in this paper had a 30° flap deflection, and in addition the pilot’s right aileron were deflected and undeflected in different cases. The solutions were computed at an airspeed of 58 KEAS, for an altitude of 6000 feet, and a flight Reynolds number of 0.588e+06 per foot. To evaluate the high-lift distributed electric propulsion system without aileron deflections, the solutions were computed for an angle-of-attack sweep from −2° to 20°, with the high-lift propellers blowing and the cruise propellers excluded from the simulation. To investigate the aileron effectiveness, the solutions were computed at angles of attack of −2° and 14°, for aileron deflections from −25° to 18° with the high-lift propellers blowing and the cruise propellers windmilling at idle-power. The high-lift propellers and the idle-power cruise propellers were modeled with an actuator disk. Results show negligible differences in lift, drag and pitching moment whether the idle-powered cruise propellers were included or excluded from the simulation. In general, the Kestrel and USM3D codes compared well for lift, drag and pitching moment for the landing configuration with no aileron control. The Kestrel code, using the Spalart-Allmaras turbulence model with the rotation corrections terms, predicted an increasing lift coefficient up to maximum lift coefficient of 4.65 at a 15° angle of attack. The USM3D code, using the Spalart-Allmaras turbulence model turbulence model with the Quadratic Constitutive Relation predicted an increasing lift coefficient up to maximum lift coefficient of 4.5 at a 12° angle of attack, with the lift remaining constant through a 14◦ angle of attack. A possible difference in lift coefficient between the codes for high angles of attack may result from the different available options used with the standard Spalart-Allmaras turbulence model. The Kestrel code predicted more drag across the range of angle of attack than the USM3D code. The codes compared well for pitching moment coefficient across the range of angle of attack. The Kestrel and USM3D codes compared well for aileron effectiveness at a 2° angle of attack. The Kestrel code predicts better aileron effectiveness than USM3D at a 14° angle of attack. There is more flow separation in the region outboard of the last high-lift nacelle for the USM3D solutions at a 14° angle of attack, which diminishes the ability of the aileron to be effective.

X-57 Maxwell Airplane↗

NASA NTRS1945

Wind-Tunnel Tests of a 1/6-Scale Model of Republic XF-12 Vertical Tail with Stub Fuselage and Stub Horizontal Tail

A 1/6-scale model of the Republic XF-12 vertical tail with stub fuselage and stub horizontal tail was tested in the Langley stability tunnel to determine the aerodynamic characteristics of the model, The investigation included a study of the effects of boundarylayer thickness, rudder area, and cover-plate alinement on the aerodynamic characteristics. Tuft studies were made in the vicinity of the junction of the vertical and stub horizontal tails. The results of the investigation indicated that the flow in the vicinity of the junction of the vertical and stub horizontal tails was only slightly improved by the addition of a fillet. An increase in boundary-layer thickness produced a slight decrease in rudder effectiveness. The increase in lift of the combined rudders over that of the upper rudder alone was not proportional at low deflections and was approximately proportional at high deflections to the increase in rudder area. When the balance-chamber cover plates were bowed out, the change in rudder hinge moment with rudder angle was less negative. The variation of the lift coefficient with angle of attack and the variation, at small values of angle of attack, of rudder hinge-noment coefficient with angle of attack was approximately the same for all model configurations tested. The upper rudder used in conjunction with a tab was found to satisfy the Army specifications regarding asymmetric power on a multiengine airplane.

MacLachlan, Robert↗

NASA NTRS2002

Progress Toward Generation of a Navier-Stokes Database for a Harrier in Ground Effect

The Harrier YAV-8B aircraft is capable of vertical and short-field take-off and landing (V/STOL) by directing its four exhaust nozzles toward the ground, or conventional flight by rotating its nozzles into a horizontal position. The British Royal Air Force and the United States Marine Corps have used this aircraft for more than 30 years to provide a quick reaction time for troop support, and reduce the need for long runways. The success of this powered-lift (PL) vehicle has also prompted the more recent design of the Joint Strike Fighter (JSF). However there are significant safety issues that must be addressed when operating a PL vehicle in close proximity to the ground. Hot Gas Ingestion (HGI) by the inlets can result in a rapid loss of powered lift; and high-speed jet flows along the ground plane can induce low pressures underneath the vehicle, causing a 'suck-down' effect. Under these conditions, departure from controlled flight may occur. Moreover, unsteady ground vortices and jet fountains can affect the aircraft,s controllability and its proximity to ground troops. The viscous, time-dependent flow fields of PL vehicles are difficult to accurately and efficiently predict using Computational Fluid Dynamics (CFD). A number of researchers have used the time-dependent Reynolds-averaged Navier-Stokes (RANS) equations to compute flows for single and multiple jets in a cross-flow. A few have added some geometric complexity to the problem by computing flows for jet-augmented delta wings near a ground plane. Smith et.al. computed for the first time a single RANS solution about a simplified Harrier. This geometry included a fuselage, wing, leading edge root extension (LERX), inlets, and exhaust nozzles. All of these investigations cite two practical problems with computing these flows: 1) the need for improved solution accuracy; and, 2) the need for faster solution methods. We view the need for faster solution methods as key to improving the solution accuracy and making this class of computation more routine. One can hardly refine grids, explore the use of advanced turbulence models, and generate databases when it takes weeks of dedicated computer time for a single solution. Chaderjian, Ahmad, Pandya, and Murman have focused on reducing the time-to-solution for this very difficult and complex problem through process automation and exploitation of parallel computing. They began with the Harrier geometry reported, and added a deflected wing flap and empennage for greater realism. To date more than 80 solutions have been carried out. This paper will describe this process and progress made in reducing the time required to generate a simple longitudinal force and moment database for a Harrier in ground effect. It shows a typical snap-shot from an unsteady streakline animation, where fluid particles are colored by temperature. The ground vortex and a jet-fountain vortex are highlighted. It also shows a similar streakline image, where HGI occurs due to the vehicle in close proximity to the ground. It is show the mean lift coefficient as a function of angle of attack and height. The angle of attack range was 4 deg less than or = alpha less than or = 10 deg with an increment of 1 degree, and the height range was 10 ft less than or = h less than or = 30ft with an increment of 5 feet. This 35 solution database was extended to over 2500 cases using a monotone cubic-spline interpolation procedure. The suck-down effect (reduction of lift near the ground) is highlighted in the figure. The "cushion effect," the conventional reduction of lift as the vehicle moves out of ground effect, is also indicated. All 35 RANS solutions were obtained using 952 Silicon Graphics Origin 2000 and 3000 processors in dedicated mode for one week. Typically, 112 processors were assigned to each case. Some other cases used fewer processors to utilize all available CPUS. The final paper will report on the automation of the solution process, including: grid generation, job monitoring, solution completion criteria, and post processing. Moreover, improvements in parallel efficiency for a dual time-step algorithm for the RANS equations will also be presented. Results will be discussed in detail using unsteady streakline flow visualization to correlate unsteady flow structures with dominant aerodynamic frequencies. The stability derivatives, CL, and CL, will also be presented.

Chaderjian, Neal M.↗

NASA NTRS2014

Observations on CFD Verification and Validation from the AIAA Drag Prediction Workshops

The authors provide observations from the AIAA Drag Prediction Workshops that have spanned over a decade and from a recent validation experiment at NASA Langley. These workshops provide an assessment of the predictive capability of forces and moments, focused on drag, for transonic transports. It is very difficult to manage the consistency of results in a workshop setting to perform verification and validation at the scientific level, but it may be sufficient to assess it at the level of practice. Observations thus far: 1) due to simplifications in the workshop test cases, wind tunnel data are not necessarily the “correct” results that CFD should match, 2) an average of core CFD data are not necessarily a better estimate of the true solution as it is merely an average of other solutions and has many coupled sources of variation, 3) outlier solutions should be investigated and understood, and 4) the DPW series does not have the systematic build up and definition on both the computational and experimental side that is required for detailed verification and validation. Several observations regarding the importance of the grid, effects of physical modeling, benefits of open forums, and guidance for validation experiments are discussed. The increased variation in results when predicting regions of flow separation and increased variation due to interaction effects, e.g., fuselage and horizontal tail, point out the need for validation data sets for these important flow phenomena. Experiences with a recent validation experiment at NASA Langley are included to provide guidance on validation experiments.

Computational Fluid Dynamics↗

NASA NTRS1946

Wind-tunnel Investigation of End-plate Effects of Horizontal Tails on a Vertical Tail Compared with Available Theory

A vertical-tail model with stub fuselage was tested in combination with various simulated horizontal tails to determine the effect of horizontal-tail span and location on the aerodynamic characteristics of the vertical tail. Available theoretical data on end-plate effects were collected and presented in the form most suitable for design purposes. Reasonable agreement was obtained between the measured and theoretical end-plate effects of horizontal tails on vertical tails, and the data indicated that the end-plate effect was determined more by the location of the horizontal tail than by the span of the horizontal tail. The horizontal tail gave most end-plate effect when located near either tip of the vertical tail and, when located near the base of the vertical tail, the end-plate effect was increased by moving the horizontal tail rearward.

TAIL SURFACES - HINGE MOMENTS↗

NASA NTRS1986

Experimental study of effects of forebody geometry on high angle of attack static and dynamic stability and control

A series of low-speed wind tunnel tests on a generic airplane model with a cylindrical fuselage were made to investigate the effects of forebody shape and fitness ratio, and fuselage/wing proximity on static and dynamic lateral/directional stability. In addition, some preliminary testing to determine the effectiveness of deflectable forebody strakes for high angle of attack yaw control was conducted. During the stability investigation, 11 forebodies were tested including three different cross-sectional shapes with fineness ratios of 2, 3, and 4. In addition, the wing was tested at two longitudinal positions to provide a substantial variation in forebody/wing proximity. Conventional force tests were conducted to determine static stability characteristics, and single-degree-of-freedom free-to-roll tests were conducted to study the wing rock characteristics of the model with the various forebodies. Flow visualization data were obtained to aid in the analysis of the complex flow phenomena involved. The results show that the forebody cross-sectional shape and fineness ratio and forebody/wing proximity can strongly affect both static and dynamic (roll) stability at high angles of attack. These characteristics result from the impact of these factors on forebody vortex development, the behavior of the vortices in sideslip, and their interaction with the wing flow field. Preliminary results from the deflectable strake investigation indicated that forebody flow control using this concept can provide very large yaw control moments at stall and post-stall angles of attack.

Brandon, J. M.↗