SEARCH · Search NASA

Results for “Failure behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS2018

An Abrupt Transition to an Intergranular Failure Mode in the Near-Threshold Fatigue Crack Growth Regime in Ni-Based Superalloys

Cyclic near-threshold fatigue crack growth (FCG) behavior of two disk superalloys was evaluated and was shown to exhibit an unexpected sudden failure mode transition from a mostly transgranular failure mode at higher stress intensity factor ranges to an almost completely intergranular failure mode in the threshold regime. The change in failure modes was associated with a crossover of FCG resistance curves in which the conditions that produced higher FCG rates in the Paris regime resulted in lower FCG rates and increased Kth values in the threshold region. High-resolution scanning and transmission electron microscopy were used to carefully characterize the crack tips at these near-threshold conditions. Formation of stable Al-oxide followed by Cr-oxide and Ti-oxides was found to occur at the crack tip prior to formation of unstable oxides. To contrast with the threshold failure mode regime, a quantitative assessment of the role that the intergranular failure mode has on cyclic FCG behavior in the Paris regime was also performed. It was demonstrated that even a very limited intergranular failure content dominates the FCG response under mixed mode failure conditions.

Telesman, J.↗

NASA NTRS1984

The characterization of Mode I delamination failure in non-woven, multidirectional laminates

The uniform double cantilever beam test and SEM are presently used for the characterization of Mode I delamination behavior in fiber-reinforced epoxy laminates. Delamination failure assumes forms that depend on ply orientation, test specimen geometry, and matrix toughness, but the calculated fracture energy is noted to be heavily dependent on fracture surface morphology. A material property concept that is independent of both test specimen geometry and the orientation of the plies constituting the delaminating interface is elucidated, through the definition of interlaminar fracture solely in terms of an interlaminar separation that includes no fiber breakage or pull-out. This value, which dissipates the lowest possible amount of energy during crack growth, is the controlling factor for laminate toughness.

Chai, H.↗

NASA NTRS1992

Thermostructural responses of carbon phenolics in a restrained thermal growth test

The thermostructural response of carbon phenolic components in a solid rocket motor (SRM) is a complex process. It involves simultaneous heat and mass transfer along with chemical reactions in a multiphase system with time-dependent material properties and boundary conditions. In contrast to metals, the fracture of fiber-reinforced composites is characterized by the initiation and progression of multiple failures of different modes such as matrix cracks, interfacial debonding, fiber breaks, and delamination. The investigation of thermostructural responses of SRM carbon phenolics is further complicated by different failure modes under static and dynamic load applications. Historically, there have been several types of post-firing anomalies found in the carbon phenolic composites of the Space Shuttle SRM nozzle. Three major failure modes which have been observed on SRM nozzles are pocketing (spallation), ply-lift, and wedge-out. In order to efficiently control these anomalous phenomena, an investigation of fracture mechanisms under NASA/MSFC RSRM (Redesigned Solid Rocket Motor) and SPIP (Solid Propulsion Integrity Program) programs have been conducted following each anomaly. This report reviews the current progress in understanding the effects of the thermostructural behavior of carbon phenolics on the failure mechanisms of the SRM nozzle. A literature search was conducted and a technical bibliography was developed to support consolidation and assimilation of learning from the RSRM and SPIP investigation efforts. Another important objective of this report is to present a knowledge-based design basis for carbon phenolics that combines the analyses of thermochemical decomposition, pore pressure stresses, and thermostructural properties. Possible areas of application of the knowledge-based design include critical material properties development, nozzle component design, and SRM materials control.

Wang, C. Jeff↗

NASA NTRS1988

Composite materials: Testing and design

The present conference discusses topics in the analysis of composite structures, composite materials' impact and compression behavior, composite materials characterization methods, composite failure mechanisms, NDE methods for composites, and filament-wound and woven composite materials' fabrication. Attention is given to the automated design of a composite plate for damage tolerance, the effects of adhesive layers on composite laminate impact damage, instability-related delamination growth in thermoset and thermoplastic composites, a simple shear fatigue test for unidirectional E-glass epoxy, the growth of elliptic delaminations in laminates under cyclic transverse shear, and the mechanical behavior of braided composite materials.

Whitcomb, John D.↗

NASA NTRS1986

The role of damage-softened material behavior in the fracture of composites and adhesives

Failure mechanisms of materials under very high strains experienced at and ahead of the crack tip such as formation, growth, and interaction of microvoids in ductile materials, microcracks in brittle solids or crazes in polymers and adhesives are represented by one-dimensional, nonlinear stress-strain relations possessing different ways by which the material loses capacity to carry load up to fracture or total separation. A double cantilever beam (DCB) type specimen is considered. The nonlinear material is confined to a thin strip between the two elastic beams loaded by a wedge. The problem is first modeled as a beam on a nonlinear foundation. The pertinent equation is solved numerically as a two-point boundary value problem for both the stationary and the quasi-stationay propagating crack. A finite element model is then used to model the problem in more detail in order to assess the adequacy of the beam model for the reduction of experimental data to determine in-situ properties of the thin interlayer.

Ungsuwarungsri, T.↗

NASA NTRS2015

Creep Behavior and Durability of Cracked CMC

To understand failure mechanisms and durability of cracked Ceramic matrix composites (CMCs), Melt Infiltration (MI) SiCSiC composites with Sylramic-iBN fibers and full Chemical vapour infiltration SiCSiC composites with Sylramic-ion bombarded BN (iBN) and Hi-Nicalon -S fibers were pre-cracked between 150 to 200 megapascal and then creep and Sustained Peak Low Cycle Fatigue (SPLCF) tested at 13150 C at stress levels from 35 to 103 megapascal for up to 200 hours under furnace and burner rig conditions. In addition creep testing was also conducted on pre-cracked full Chemical vapour infiltration SiCSiC composites at 14500 C between 35 and 103 megapascal for up to 200 hours under furnace conditions. If the specimens survived the 200 hour durability tests, then they were tensile tested at room temperature to determine their residual tensile properties. The failed specimens were examined by Scanning electron microscope (SEM) to determine the failure modes and mechanisms. The influence of crack healing matrix, fiber types, crack density, testing modes and interface oxidation on durability of cracked Ceramic matrix composites (CMCs) will be discussed.

Creep↗

NASA NTRS1989

Incorporation of a progressive failure analysis method in the CSM testbed software system

Analysis of the postbuckling behavior of composite shell structures pose many difficult and challenging problems in the field of structural mechanics. Current analysis methods perform well for most cases in predicting the postbuckling response of undamaged components. To predict component behavior accurately at higher load levels, the analysis must include the effects of local material failures. The CSM testbed software system is a highly modular structural analysis system currently under development at Langley Research Center. One of the primary goals of the CSM testbed is to provide a software environment for the development of advanced structural analysis methods and modern numerical methods which will exploit advanced computer architecture such as parallel-vector processors. Development of a progressive failure analysis method consists of the design and implementation of a processor which will perform the ply-level progressive failure analysis and the development of a geometrically nonlinear analysis procedure which incorporates the progressive failure processor. Regarding the development of the progressive failure processor, two components are required: failure criteria and a degradation model. For the initial implementation, the failure criteria of Hashin will be used. For a matrix failure which typically indicates the development of transverse matrix cracks, the ply properties will be degraded. Work to date includes the design of the progressive failure analysis processor and initial plans for the controlling geometrically nonlinear analysis procedure. The implementation of the progressive failure analysis has begun. Access to the model database and the Hashin failure criteria are completed. Work is in progress on the input/output operations for the processor related data and the finite element model updating procedures. In total the progressive failure processor is approximately one-third complete.

Arenburg, Robert T.↗

NASA NTRSDate not supplied

Progressive Damage Failure Analysis of a Multi-Stringer Post-Buckled Panel

Validation of a progressive damage finite element analysis model using the CompDam material model was performed on a large multi-stringer panel subjected to compressive loading. The panel had a Teflon insert embedded between the skin panel and stiffener to cause an ultimate failure mode of stiffener separation. The compressive loading of the panel caused the skin between the stiffeners to locally buckle before any damage began to occur. The post-buckled behavior of the panel was the driving mechanism to the onset of damage and the damage growth that led to skin-stiffener separation. An integrated global-local modeling approach was used to validate several aspects the overall behavior of the panel from start to failure. The global region captured the pre-buckled stiffness of the test panel within 10% and the buckling load of the skin panel at the critical location within 2%. The skin’s five half-wave buckled mode shape was accurately predicted by the model. The integrated local model captured the load corresponding to the onset of damage within 5% of the average test data. Comparisons are made for key aspects of the damage morphology, such as a growth pattern that included a significant matrix split in the first ply of the skin and a migration of the delamination from the skin-stiffener interface to the skin’sply1-ply2 interface. The ultimate failure mode was shown to be an unstable growth of delamination damage under the stiffeners which led to a peak load of the analysis that was approximately 5% above the average peak load of the testing. The validated global-local modeling approach used on the multi-stringer post-buckled panel with a Teflon insert used a methodology and lessons learned using smaller specimens applied to a subcomponent that captured several aspects of a modern aircraft design.

Jason Action↗

NASA NTRS1994

Mechanical Properties of Shock-Damaged Rocks

Stress-strain tests were performed both on shock-damaged gabbro and limestone. The effective Young's modulus decreases with increasing initial damage parameter value, and an apparent work-softening process occurs prior to failure. To further characterize shock-induced microcracks, the longitudinal elastic wave velocity behavior of shock-damaged gabbro in the direction of compression up to failure was measured using an acoustic transmission technique under uniaxial loading. A dramatic increase in velocity was observed for the static compressive stress range of 0-50 MPa. Above that stress range, the velocity behavior of lightly damaged (D(sub 0) less than 0.1) gabbro is almost equal to unshocked gabbro. The failure strength of heavily-damaged (D(sub 0) greater than 0.1) gabbro is approx. 100-150 MPa, much lower than that of lightly damaged and unshocked gabbros (approx. 230-260 MPa). Following Nur's theory, the crack shape distribution was analyzed. The shock-induced cracks in gabbro appear to be largely thin penny-shaped cracks with c/a values below 5 x 10(exp -4). Moreover, the applicability of Ashby and Sammis's theory relating failure strength and damage parameter of shock-damaged rocks was examined and was found to yield a good estimate of the relation of shock-induced deficit in elastic modulus with the deficit in compressive strength.

He, Hongliang↗

NASA NTRSDate not supplied

Applying the System Complexity Metric (SCM)

A fundamental cause of difficulty in larger engineering projects is their inherent complexity. An impression of complexity occurs if a system is simply difficult to understand, so that there is no obvious mental model that correctly predicts its behavior. Higher complexity is usually associated with higher cost and higher failure rate. Complexity is indicated by a system having more and diverse components, multiple interactions and feedback loops, transients and dynamic behavior, and often the emergence of unanticipated failure modes. Identifying and removing these signs of complexity should reduce complexity and improve performance. Here we limit complexity measurement to the number of components and their interactions. A System Complexity Metric (SCM) is defined as equal to the sum of the number of parts in a system, N, plus the sum of the one-way interconnections between them, I. SCM = N + I. The SCM is easily determined by direct inspection of system block diagrams. Previous work found that life support system cost was directly proportional to SCM and that failure rate increased faster than SCM squared. SCM can be used to compare systems or to guide their redesign to reduce cost and failure rate. Carbon dioxide removal systems will be analyzed using SCM, cost, and failure rate.

Harry W Jones↗

NASA NTRS1983

Failure during thermal cycling of plasma-sprayed thermal barrier coatings

The thermal cycling behavior of plasma-sprayed ZrO2-12 wt pct Y2O3 coatings was studied. Coatings were produced with and without bond coats of Ni-Cr-Al-Zr and in some cases the substrates were heated to above the optimum temperature prior to spraying. The coatings (attached to the substrate) were thermal cycled to 1200 C and their cracking behavior was followed by acoustic emission (AE) techniques. It was possible to examine the failure mechanisms by statistical analysis of the AE data and to evaluate the influence of preheating and bond coating. It is shown that the AE spectrum changes when a bond coat is used because of the presence of microcracks which, in turn, dissipate energy and improve the coating integrity. The preheating effect is reflected by a decrease in the peak count rate and an increase in the temperature at which AE activity is initiated.

Berndt, C. C.↗

NASA NTRS1979

Influence of interface on composite failure

The influence of the interface on the composite system behavior is investigated by analytical modeling. The stress analysis is based on the two-dimensional finite element procedure in which twelve-node isoparametric elements with cubic shape functions are used. The location of possible failure sites is predicted by the strain energy density (SED) failure theory which assumes failure to coincide with locations of minimum SED while the locations of maximum SED correspond to regions of excessive distortion or yielding. The results of the analysis show that the way in which the modulus of elasticity varies within the interface is as important in modeling as the average interface modulus.

Sih, G. C.↗

NASA NTRS1987

The role of damage-softened material behavior in the fracture of composites and adhesives

The failure mechanism of polymer composites and adhesives with high strain in the zone near and ahead of the crack tip is investigated analytically, summarizing the findings of Ungsuwarungsri (1986). A double-cantilever-beam specimen with the nonlinear material confined to a thin strip between two wedge-loaded elastic beams is modeled as a beam on a nonlinear foundation; the two-point boundary-value problem for stationary and propagating cracks is solved numerically; and an FEM approach is applied to study the behavior of the nonlinear strip in detail. Typical results are presented in extensive graphs, and the accuracy and efficiency of the present method are shown to be superior to those of the Berry (1963) procedure.

Ungsuwarungsri, T.↗

NASA NTRS2000

The Effect of Boron on the Low Cycle Fatigue Behavior of Disk Alloy KM4

The durability of powder metallurgy nickel base superalloys employed as compressor and turbine disks is often limited by low cycle fatigue (LCF) crack initiation and crack growth from highly stressed surface locations (corners, holes, etc.). Crack growth induced by dwells at high stresses during aerospace engine operation can be particularly severe. Supersolvus solution heat treatments can be used to produce coarse grain sizes approaching ASTM 6 for improved resistance to dwell fatigue crack growth. However, the coarse grain sizes reduce yield strength, which can lower LCF initiation life. These high temperature heat treatments also can encourage pores to form. In the advanced General Electric disk superalloy KM4, such pores can initiate fatigue cracks that limit LCF initiation life. Hot isostatic pressing (HIP) during the supersolvus solution heat treatment has been shown to improve LCF initiation life in KM4, as the HIP pressure minimizes formation of the pores. Reduction of boron levels in KM4 has also been shown to increase LCF initiation life after a conventional supersolvus heat treatment, again possibly due to effects on the formation tendencies of these pores. However, the effects of reduced boron levels on microstructure, pore characteristics, and LCF failure modes in KM4 still need to be fully quantified. The objective of this study was to determine the effect of boron level on the microstructure, porosity, LCF behavior, and failure modes of supersolvus heat treated KM4.

Gabb, Timothy↗

NASA NTRS2001

C-Coupon Studies of CMCS: Fracture Behavior and Microstructural Characterization

A curved beam 'C-coupon' was used to assess fracture behavior in a Sylramic(tm)/melt infiltration (MI) SiC matrix composite. Failure stresses and fracture mechanisms, as determined by optical and scanning electron microstructural analysis, are compared with finite element stress calculations to analyze failure modes. Material microstructure was found to have a strong influence on mechanical behavior. Fracture occurs in interlaminar tension (ILT), provided that the ratio of ILT to tensile strength for the material is less than the ratio of radial to hoop stresses for the C-coupon geometry. Utilization of 3D architectures to improve interlaminar strength requires significant development efforts to incorporate through thickness fibers in regions with high curvatures while maintaining uniform thickness, radius, and microstructure.

Hurwitz, Frances I.↗

NASA NTRS1978

Extended Development of Variable Conductance Heat Pipes

A high-capacity vapor-modulated heat pipe was designed and tested. In 1977, a program was undertaken to use the aforementioned heat pipe to study protection from freezing-point failure, increase control sensitivity, and transient behavior under a wide range of operating conditions in order to determine the full performance potential of the heat pipe. A new concept, based on the vapor-induced-dry-out principle, was developed for passive feedback temperature control as a heat pipe diode. This report documents this work and describes: (1) the experimental and theoretical investigation of the performance of the vapor-modulated heat pipe; and (2) the design, fabrication and test of the heat pipe diode.

Antoniuk, D.↗

NASA NTRS1984

Mental Models of Invisible Logical Networks

Subjects were required to discover the structure of a logical network whose links were invisible. Network structure had to be inferred from the behavior of the components after a failure. It was hypothesized that since such failure diagnosis tasks often draw on spatial processes, a good deal of spatial complexity in the network should affect network discovery. Results show that the ability to discover the linkages in the network is directly related to the spatial complexity of the pathway described by the linkages. This effect was generally independent of the amount of evidence available to subjects about the existence of the link. These results raise the question of whether inferences about spatially complex pathways were simply not made, or whether they were made but not retained because of a high load on memory resources.

Sanderson, P.↗

NASA NTRS1984

Some methods of computing platform transmitter terminal location estimates

A position estimation algorithm was developed to track a humpback whale tagged with an ARGOS platform after a transmitter deployment failure and the whale's diving behavior precluded standard methods. The algorithm is especially useful where a transmitter location program exists; it determines the classical keplarian elements from the ARGOS spacecraft position vectors included with the probationary file messages. A minimum of three distinct messages are required. Once the spacecraft orbit is determined, the whale is located using standard least squares regression techniques. Experience suggests that in instances where circumstances inherent in the experiment yield message data unsuitable for the standard ARGOS reduction, (message data may be too sparse, span an insufficient period, or include variable-length messages). System ARGOS can still provide much valuable location information if the user is willing to accept the increased location uncertainties.

Hoisington, C. M.↗