SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This presentation is an overview of the following, Spalling on 211 oriented wafers produces flat surface without faceting: 1) Demonstrated spall on entire 2" wafer; 2) GaAs and GaInP grown on 211 wafers by HVPE; and 3) Promising cell with VOC=1.02 V and IQE-1. Next steps: 1) Grow cell on spalled wafer and 2) Growth studies to improve material and cell on 211 substrates.
The endurance life and the friction coefficient of ceramic-bonded calcium fluoride (CaF2) coatings on nickel-base alloys were determined at temperatures from 75° to 1900° F. The specimen configuration consisted of a hemispherical rider (3/16-in. rad.) sliding against the flat surface of a rotating disk. Increasing the ambient temperature (up to 1500° F) or the sliding velocity generally reduced the friction coefficient and improved coating life. Base-metal selection was critical above 1500° F. For instance, cast Inconel sliding against coated Inconel X was lubricated effectively to 1500° F, but at 1600° F severe blistering of the coatings occurred. However, good lubrication and adherence were obtained for René 41 sliding against coated René 41 at temperatures up to 1900° F; no blisters developed, coating wear life was fairly good, and the rider wear rate was significantly lower than for the unlubricated metals . Friction coefficients were 0.12 at 1500° F, 0.15 at 1700° F, and 0.17 at 1800° and 1900° F. Because of its ready availability, Inconel X appears to be the preferred substrate alloy for applications in which the temperature does not exceed 1500° F. René 41 would have to be used in applications involving higher temperatures. Improved coating life was derived by either preoxidizing the substrate metals prior to the coating application or by applying a very thin (<0.0002 in.) burnished and sintered overlay to the surface of the coating. Preoxidation did not affect the friction coefficient. The overlay generally resulted i n a higher friction coefficient than that obtained without the overlay. The combination of both modifications resulted in longer coating life and in friction coefficients intermediate between those obtained with either modification alone.
Sensor incorporating a circular spirit level, electrical lamp and two pairs of photocells, provides an electrical indication of flat surface level deviation.
Metallurgical microsamples are held in a fixture which rotates the sample across a rotating grinding wheel. The dual rotation results in a level, flat surface on the sample.
Lubricating materials for use in a vacuum environment have been the subject of a series of experimental investigations. Evaporation properties were evaluated for solid polymeric compositions. Friction and wear studies explored the behavior during sliding contact for series of polymeric compositions, binary alloys containing soft film-forming phases, complex alloys with film-forming materials, and a burnished MoS2 film. Friction and wear experiments were conducted at 10(exp-9)mm Hg with a 3/16-inch-radius-hemisphere rider specimen sliding on the flat surface of a rotating 2-1/2-inch-diameter disk specimen with materials that had low rates of evaporation. The influence of fillers in polytetrafluoroethylene (PTFE) on decomposition during vacuum friction studies was determined with a mass spectrometer. A real advantage in reducing decomposition and improving friction wear properties is gained by adding fillers (e.g., copper) that improve thermal conductivity through the composite materials. A polyimide and an epoxy-MoS2 composition material were found to have better friction and wear properties than PTFE compositions. A series of alloys (cast binary as well as more complex alloys) that contained microinclusions of potential film-forming material was studied. These materials replaced the normal surface oxides as they were worn away on sliding contact. Iron sulfide, nickel oxide, and tin are typical film-forming materials employed and were demonstrated to be effective in inhibiting surface welding and reducing friction. A burnished MoS2 film applied to type 440-C stainless steel in argon with a rotating soft wire brush had good endurance properties but somewhat higher friction than commercially available bonded films. An oil film applied to the burnished MoS2 markedly reduced its endurance life.
Granular aluminum oxide is used as filler in serpentine tubing while welding the tubing to a flat surface. The filler eliminates obstructions in the tubes formed by molten weld nuggets and is porous enough to allow gases to escape from the welding area.
Identification breakdown chart that lists the component parts required for any specific end item is used to identify rapidly and accurately, from numerous drawings, all the component parts of a complex design assembly. Cylindrical and complex configurations are depicted as continuous flat surfaces for ready identification.
Shapes of liquid drops resting on flat surfaces determined by Runge-Kutta solution of Laplace capillary equation
Pin locking technique for flush fasteners retains a screw under dynamic conditions when self-locking or lock wiring devices are not practical. Spring pin is counter sunk through one side of the screw head into the component to form a flat surface.
Method of bonding materials to a flat surface eliminates the use of bolts to hold the pieces together. Two adhesives are used, the primary or permanent bonding material and a quick setting adhesive. No permanent after effects are left on the surfaces to which the materials are bonded.
Reflection of plane waves from stress free flat surface of micropolar elastic half space, presenting reflection laws and amplitude ratios
Electromechanical hand incorporates touch sensors, concealed fingers, and a structure that allows the hand to hold a tool on a flat surface. The hands can be mounted on most types of existing manipulators either directly or by means of modified mounting brackets.
Film condensation and heat transfer of low pressure metal vapor on flat surfaces
Seven superalloy models were tested in a plasma arc tunnel facility. The test models were 3 in. (7.62cm) square flat surfaces (nominally 0.01 to 0.02 in. (0.0254 to 0.0508 cm) thick) held in a water-cooled wedge holder at a 60 deg (1.05 rad) angle of attack. The models were cycled 25 times (two were cycled 50 times) for 10 min each cycle in a Mach 4.6 test stream with the model leading edge temperature maintained at 2200 F (1478 K) (one at 2000 F (1367 K)). Backface temperatures were measured with four platinum-platinum 10% rhodium thermocouples and the front surface temperatures with an optical pyrometer. Four different nickel base alloy materials and one cobalt material were evaluated.
Heat transfer characteristics of single and multiple turbulent air jets impinging on flat surfaces have been studied by many investigators. Results of many of these studies are summarized. Suggested correlations for use in the design of cooled turbine blades are noted, and areas where further research would be advisable are identified.
Using scanning electron microscopy, Si epitaxial growth from solution in solid Al onto crystal Si substrates was studied. Growth in reentrant corners of the substrate was found to be favored over growth onto a flat surface. These preferred locations for growth appear to be the result of a force not present in conventional crystal growth from fluid media, namely, the nonuniform stress field present in solids.
Magnetometer is simple to operate and has fast response. Transducer is rugged and flat and can measure magnetic fields as close as 0.08 mm from any relatively flat surface. Magnetometer has active region of approximately 0.64 by 0.76 mm and is capable of good spatial resolution of magnetic fields as low as 0.02 Oe (1.6 A/m).
Device provides low-cost unit for efficiently transferring heat between, either to or from, flat surface and central point or region. It is based upon vapor heat transfer principle and therefore, extends applicability of heat pipe.