Compilation of flight data from Titan III VEHICLES
Vibration, acoustic, and shock data for Titan III flight vehicle
ACOUSTIC VIBRATION↗
SEARCH · Search NASA
Results for “Flight data”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Identification of a STOL propulsion plant model from flight data
Accurate dynamic models for propulsion system behavior are critical to successful synthesis of STOL autothrottle/autoland control systems. This paper describes the development of a nonlinear dynamic model for the response of a STOL aircraft in the landing/approach configuration. The model is based upon an analysis of the throttle, governor, and turbofan engine components. Model parameters are directly identified from data acquired during a flight of the NASA Augmentor Wing Jet STOL research aircraft. The accuracy of the model and a comparison of results for two engines are described. Various approaches to modeling propulsion system response for complex systems representative of current and near-term aircraft are discussed.
De Hoff, R. L.↗
Obtaining consistent models of helicopter flight-data measurement errors using kinematic-compatibility and state-reconstruction methods
A new method was developed for application of Kalman Filter/Smoothers to post-flight processing of helicopter flight test dynamic measurements. This processing includes checking for kinematic compatibility among the measurements, identification of a measurement error model, and reconstruction of both measured and unmeasured time histories. Emphasis is placed on identification of a parametric measurement error model which is valid for a set of flight test data. This is facilitated through a new method of concatenating several maneuver time histories. The method also includes a model structure determination step which ensures that a physically realistic parameterization has been achieved. Application of the method to a set of BO-105 flight test data is illustrated. The resulting minimally parameterized error model is shown to characterize the measurement errors of the entire data set with very little variation in the parameter values. Reconstructed time histories are shown to have increased bandwidths and signal to noise ratios.
Fletcher, Jay W.↗
Flight data for the Cryogenic Heat Pipe (CRYOHP) Experiment
This paper presents the flight test results and data correlation for the Cryogenic Heat Pipe Flight Experiment (CRYOHP). CRYOHP is a Hitchhiker Canister experiment that was flown aboard the shuttle Discovery (STS-53) in December of 1992. Two different axially grooved oxygen heat pipes were tested to determine their startup behavior and transport capability in micro-gravity. Three startup cycles were conducted with each heat pipe and transport data was obtained over the range of 60 K to 140 K. Startup in flight was repeatable but slower than observed in ground tests. The transport data shows good agreement with the theoretical model. The CRYOHP test bed, which incorporates five Stifling cycle refrigerators to provide the cryo-cooling, performed as predicted and offers a good micro-gravity test bed for cryogenic thermal devices.
Brennan, Patrick J.↗
Comparison of Fluka-2006 Monte Carlo Simulation and Flight Data for the ATIC Detector
We have performed a detailed Monte Carlo (MC) simulation for the Advanced Thin Ionization Calorimeter (ATIC) detector using the MC code FLUKA-2006 which is capable of simulating particles up to 10 PeV. The ATIC detector has completed two successful balloon flights from McMurdo, Antarctica lasting a total of more than 35 days. ATIC is designed as a multiple, long duration balloon flight, investigation of the cosmic ray spectra from below 50 GeV to near 100 TeV total energy; using a fully active Bismuth Germanate(BGO) calorimeter. It is equipped with a large mosaic of.silicon detector pixels capable of charge identification, and, for particle tracking, three projective layers of x-y scintillator hodoscopes, located above, in the middle and below a 0.75 nuclear interaction length graphite target. Our simulations are part of an analysis package of both nuclear (A) and energy dependences for different nuclei interacting in the ATIC detector. The MC simulates the response of different components of the detector such as the Si-matrix, the scintillator hodoscopes and the BGO calorimeter to various nuclei. We present comparisons of the FLUKA-2006 MC calculations with GEANT calculations and with the ATIC CERN data and ATIC flight data.
Gunasingha, R.M.↗
Ares I-X Launch Abort System, Crew Module, and Upper Stage Simulator Vibroacoustic Flight Data Evaluation, Comparison to Predictions, and Recommendations for Adjustments to Prediction Methodology and Assumptions
The National Aeronautics and Space Administration (NASA) Constellation Program (CxP) has identified a series of tests to provide insight into the design and development of the Crew Launch Vehicle (CLV) and Crew Exploration Vehicle (CEV). Ares I-X was selected as the first suborbital development flight test to help meet CxP objectives. The Ares I-X flight test vehicle (FTV) is an early operational model of CLV, with specific emphasis on CLV and ground operation characteristics necessary to meet Ares I-X flight test objectives. The in-flight part of the test includes a trajectory to simulate maximum dynamic pressure during flight and perform a stage separation of the Upper Stage Simulator (USS) from the First Stage (FS). The in-flight test also includes recovery of the FS. The random vibration response from the ARES 1-X flight will be reconstructed for a few specific locations that were instrumented with accelerometers. This recorded data will be helpful in validating and refining vibration prediction tools and methodology. Measured vibroacoustic environments associated with lift off and ascent phases of the Ares I-X mission will be compared with pre-flight vibration predictions. The measured flight data was given as time histories which will be converted into power spectral density plots for comparison with the maximum predicted environments. The maximum predicted environments are documented in the Vibroacoustics and Shock Environment Data Book, AI1-SYS-ACOv4.10 Vibration predictions made using statistical energy analysis (SEA) VAOne computer program will also be incorporated in the comparisons. Ascent and lift off measured acoustics will also be compared to predictions to assess whether any discrepancies between the predicted vibration levels and measured vibration levels are attributable to inaccurate acoustic predictions. These comparisons will also be helpful in assessing whether adjustments to prediction methodologies are needed to improve agreement between the predicted and measured flight data. Future assessment will incorporate hybrid methods in VAOne analysis (i.e., boundary element methods, BEM and finite element methods, FEM). These hybrid methods will enable the ability to import NASTRAN models providing much more detailed modeling of the underlying beams and support structure of the ARES 1-X test vehicle. Measured acoustic data will be incorporated into these analyses to improve correlation for additional post flight analysis.
Smith, Andrew↗
A technique for determining powered-lift STOL aircraft performance at sea level from flight data taken at altitude
State-of-the-technology powered-lift STOL aircraft can develop very high lift coefficients. The determination of how this high lift capability can be utilized for landing approaches is accomplished by evaluating aircraft velocity versus flightpath performance. This paper briefly discusses upper-surface-blowing power-lift technology and some of the significant features of the velocity versus flightpath plot that are used in evaluating the performance of powered-lift aircraft. A procedure for deriving the velocity versus flightpath plot for a powered-lift aircraft at any specified weight at sea level, based on flight-test data obtained at various weights and altitudes, is discussed in detail. Actual flight-test data obtained with NASA's Quiet Short-Haul Research Aircraft (QSRA) are used to illustrate this procedure and to evaluate the results.
Stevens, V. C.↗
Inference of the neutron down-scatter ratio using neutron time-of-flight data for DT-layered implosions on the OMEGA laser
First analysis of the neutron time of flight (nTOF) data is presented to infer the areal density using the neutron down-scatter ratio (DSR) for OMEGA deuterium–tritium (DT)-layered (cryogenic) implosions. The required very-high-dynamic range (nTOF) signal is constructed using an nTOF detector [Forrest et al., Rev. Sci. Ins. 83, 10D919 (2012)] with multiple time-gated photomultiplier tubes. The nTOF data are analyzed using a forward-fit technique to account for the detector responses and infer the DSR and areal density for DT-layered implosions. The areal densities inferred using this analysis are found to be in agreement with the areal densities measured using the magnetic recoil spectrometer detector that is located in a similar line-of-sight. This work establishes the feasibility of the DSR measurement using nTOF data on OMEGA and provides an additional areal-density measurement that will benefit the assessment of the implosion performance and 3D reconstruction of the imploded core.
47 OTHER INSTRUMENTATION↗
Analytical redundancy management mechanization and flight data analysis for the F-8 digital fly-by-wire aircraft flight control sensors
The details are presented of an onboard digital computer algorithm designed to reliably detect and isolate the first failure in a duplex set of flight control sensors aboard the NASA F-8 digital fly-by-wire aircraft. The algorithm's successful flight test program is summarized, and specific examples are presented of algorithm behavior in response to software-induced signal faults, both with and without aircraft parameter modeling errors.
Deckert, J. C.↗
Flight data identification of six degree-of-freedom stability and control derivatives of a large crane type helicopter
Flight test data from a large 'crane' type helicopter were collected and processed for the purpose of identifying vehicle rigid body stability and control derivatives. The process consisted of using digital and Kalman filtering techniques for state estimation and Extended Kalman filtering for parameter identification, utilizing a least squares algorithm for initial derivative and variance estimates. Data were processed for indicated airspeeds from 0 m/sec to 152 m/sec. Pulse, doublet and step control inputs were investigated. Digital filter frequency did not have a major effect on the identification process, while the initial derivative estimates and the estimated variances had an appreciable effect on many derivative estimates. The major derivatives identified agreed fairly well with analytical predictions and engineering experience. Doublet control inputs provided better results than pulse or step inputs.
Tomaine, R. L.↗
Titan/Centaur D-1T TC-2, Helios A flight data report
Background data of spacecraft launching and flight are presented. A system analysis of the space vehicles is included, specifically on: (1) electronic equipment, (2) hydraulic equipment, (3) telemetry, (4) propulsion systems, (5) software (computers), and (6) guidance. Spacecraft and launch vehicle configurations are shown and described.
Source record↗
Modeling correlation with flight data
The molecular contamination flow model (space 2 program) predicts the induced environment of the space shuttle orbiter/payload on orbit as well as the induced gas flow between the orbiter and payload surfaces. This computer program relates the input parameters which characterize the time dependent status of the orbiter/payload to the required output parameters. An application of the model to data from space transportation system flights 1, 2, and 3 shows that the model correlates well for direct flow and for return flux (STS-2/H2O). Correlation for return flux from other molecular sources/species appears to be within expectations but more analysis is required. The space 2 model seems to be an adequate predictive tool.
Ehlers, H. K. F.↗
Application of flight data to Space Shuttle CCD star tracker catalog design
The new Shuttle Solid-State Tracker (SSST) is an improved but transparent replacement for the analog version which has flown on every Shuttle mission. This paper will examine the data collected from four Shuttle flights to establish parameters for selection of acceptable navigation stars, and apply those parameters to establish a star catalog which will be sufficient to ensure the ability of the SSST to perform attitude updates while docked to the Space Station.
Barry, Karen↗
Space shuttle wing leading edge heating environment prediction derived from development flight data
An analytical program is in progress at Rockwell International to revise wing leading edge heating predictions in order to improve correlation with STS-1 to -5 flight radiometer data. This paper discusses the methods that have been used to improve agreement between prediction and flight and summarizes the aerodynamic correlations which, when updated, will be used to analyze future orbiter missions.
Cunningham, J. A.↗
Analysis of STS-3 Get Away Special (GAS) flight data and vibration specification for gas payloads
During the Space Transportation System (STS)-3 mission, a Get Away Special (GAS) canister was flown. In order to determine the flight environment for GAS payloads, triaxial accelerometers and a microphone were installed inside the GAS canister. Data from these accelerometers and the microphone were analyzed. The microphone data is presented as overall sound pressure level (SPL) and one-third octave band time history plots. And the accelerometer data is provided in the forms of instantaneous time history, RMS time history and power spectral density plots. Also based on this flight data, vibration test specification for GAS payloads was developed and the recommended specification is presented here.
Talapatra, D. C.↗
JT15D simulated flight data evaluation
The noise characteristics of the JT15D turbofan engine was analyzed with the objectives of: (1) assessing the state-of-art ability to simulate flight acoustic data using test results acquired in wind tunnel and outdoor (turbulence controlled) environments; and (2) predicting the farfield noise directivity of the blade passage frequency (BPF) tonal components using results from rotor blade mounted dynamic pressure instrumentation. Engine rotor tip speeds at subsonic, transonic, and supersonic conditions were evaluated. The ability to simulate flight results was generally within 2-3 dB for both outdoor and wind tunnel acoustic results. Some differences did occur in the broadband noise level and in the multiple-pure-tone harmonics at supersonic tip speeds. The prediction of blade passage frequency tone directivity from dynamic pressure measurements was accomplished for the three tip speed conditions. Predictions were made of the random and periodic components of the tone directivity. The technique for estimating the random tone component used hot wire data to establish a correlation between dynamic pressure and turbulence intensity. This prediction overestimated the tone level by typically 10 dB with the greatest overestimates occurring at supersonic conditions.
Holm, R. G.↗
Approximate method of predicting heating on the windward side of Space Shuttle Orbiter and comparisons with flight data
An approximate method is developed for predicting laminar and turbulent heating rates on the windward side of the Space Shuttle Orbiter for both the wind-tunnel and flight environments. The method is based on a 'local infinite swept cylinder' analysis and includes both equilibrium-air chemistry and variable boundary-layer-edge entropy. The method is validated by comparing with data from wind-tunnel experiments and from the first and second Space Shuttle flights both along the windward-symmetry plane and in a lateral direction off the symmetry plane. Agreement with the flight data is good from approximately 67 km (peak heating) downward.
Hamilton, H. H., II↗
Radiative Viscous Shock Layer Analysis of Fire, Apollo, and PAET Flight Data
Equilibrium, radiating viscous shock layer solutions are obtained for a number of trajectory points of the Fire II, Apollo 4, and PAET experimental flight vehicles. Convective heating rates calculated by a benchmark code agree well with two engineering correlations, except at high altitudes corresponding to low densities. Calculated radiation intensities are compared with the flight radiometer data and with inviscid flow results. Differences as great as 70% are observed between measured data and the viscous calculations. Because of boundary-layer absorption, viscous effects reduce the intensity to the wall by as much as 30% compared with inviscid intensities. Preliminary chemical and thermal nonequilibrium flow calculations along a stagnation streamline for a PAET trajectory predict an enhancement to the radiation owing to the chemical relaxation. Stagnation point solutions are also presented for future aeroassisted orbital transfer vehicle geometries with nose radii of 0.3-15 m.
Balakrishnan, A.↗