SEARCH · Search NASA

Results for “Flight test measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1983

Space Shuttle Orbiter Venting: Lessons Learned

The orbiter vent system provides dedicated vent areas to permit the gases trapped inside the vehicle to escape during accent. The same vent system also repressurizes the vehicle during entry. The vent system is one of six systems that constitutes the purge, vent and drain subsystem. The orbiter active vent system has been very adaptable to the changing requirements that have occurred during the development of the Space Shuttle orbiter. Good correlation has been obtained between predicted and measured compartment pressures during the orbital flight test (OFT) program. An investigation of the flight data showed that the difference between preflight prediction and the measured values were primarily due to the difference between the baseline external pressures, which was based on subscale wind tunnel test data, and the actual vehicle local external pressures measured during the flight. The current predictions are based on flight derived vent port pressure coefficients since the wind tunnel data does not adequately define the orbiter ascent pressure environment.

H S Lutfi↗

NASA NTRS1996

Helicopter Rotor Blade Computation in Unsteady Flows Using Moving Overset Grids

An overset grid thin-layer Navier-Stokes code has been extended to include dynamic motion of helicopter rotor blades through relative grid motion. The unsteady flowfield and airloads on an AH-IG rotor in forward flight were computed to verify the methodology and to demonstrate the method's potential usefulness towards comprehensive helicopter codes. In addition, the method uses the blade's first harmonics measured in the flight test to prescribe the blade motion. The solution was impulsively started and became periodic in less than three rotor revolutions. Detailed unsteady numerical flow visualization techniques were applied to the entire unsteady data set of five rotor revolutions and exhibited flowfield features such as blade vortex interaction and wake roll-up. The unsteady blade loads and surface pressures compare well against those from flight measurements. Details of the method, a discussion of the resulting predicted flowfield, and requirements for future work are presented. Overall, given the proper blade dynamics, this method can compute the unsteady flowfield of a general helicopter rotor in forward flight.

Ahmad, Jasim↗

NASA NTRS1983

Balloon film strain measurement

A discussion is presented of the results of a flight test program in which scientific research balloon material strain was measured in order to determine stress levels. Attention is given to material strain characteristics during the inflation, launch, ascent, and flight of a natural shape, zero-pressure scientific balloon. Measurements were conducted with a simple thin film strain transducer. Thermal, meridional and circumferential strain history data for the test flight are given.

Rand, J. L.↗

NASA NTRS2001

Analysis of Measured and Predicted Acoustics from an XV-15 Flight Test

Flight acoustic and vehicle state data from an XV-15 acoustic flight test are examined. Flight predictions using TRAC are performed for a level flight (repeated) and four descent conditions (including a BVI). The assumptions and procedures used for TRAC flight predictions as well as the variability in flight measurements, which are used for input and comparison to predictions, are investigated in detail. Differences were found in the measured vehicle airspeed, altitude, glideslope, and vehicle orientation (yaw, pitch and roll angle) between each of the repeat runs. These differences violate some of the prediction assumptions and significantly impacted the resulting acoustic predictions. Multiple acoustic pulses, with a variable time between the pulses, were found in the measured acoustic time histories for the repeat runs. These differences could be attributed in part to the variability in vehicle orientation. Acoustic predictions that used the measured vehicle orientation for the repeat runs captured this multiple pulse variability. Thickness noise was found to be dominant on approach for all the cases, except the BVI condition. After the aircraft passed overhead, broadband noise and low frequency loading noise were dominant. The predicted LowSPL time histories compared well with measurement on approach to the array for the non-BVI conditions and poorly for the BVI condition. Accurate prediction of the lift share between the rotor and fuselage must be known in order to improve predictions. At a minimum, measurements of the rotor thrust and tip-path-plane angle are critical to further develop accurate flight acoustic prediction capabilities.

Boyd, D. Douglas, Jr.↗

NASA NTRS1975

The application of measurement techniques to track flutter testing

The application is discussed of measurement techniques to captive flight flutter tests at the Supersonic Naval Ordnance Research Track (SNORT), U. S. Naval Ordnance Test Station, China Lake, California. The high-speed track, by its ability to prove the validity of design and to accurately determine the actual margin of safety, offers a unique method of flutter testing for the aircraft design engineer.

Roglin, H. R.↗

NASA NTRS2001

Analysis of Measured and Predicted Acoustics From an XV-15 Flight Test

Flight acoustic and vehicle state data from an XV-15 acoustic flight test are examined. Flight predictions using TiltRotor Aeroacoustic Code (TRAC) are performed for a level flight (repeated) and four descent conditions (including a blade vortex interaction (BVI)). The assumptions and procedures used for TRAC flight predictions as well as the variability in flight measurements, which are used for input and comparison to predictions, are investigated in detail. Differences were found in the measured vehicle airspeed, altitude, glideslope, and vehicle orientation (yaw, pitch, and roll angle) between each of the repeat runs. These differences violate some of the prediction assumptions and significantly impacted the resulting acoustic predictions. Multiple acoustic pulses, with a variable time between the pulses, were found in the measured acoustic time histories for the repeat runs. These differences could be attributed in part to the variability in vehicle orientation. Acoustic predictions that used the measured vehicle orientation for the repeat runs captured this multiple pulse variability. Thickness noise was found to be dominant on approach for all the cases, except the BVI condition. After the aircraft passed overhead, broadband noise and low frequency loading noise were dominant. The predicted LowSPL time histories compared well with measurement on approach to the array for the non-BVI conditions and poorly for the BVI condition. Accurate prediction of the lift share between the rotor and fuselage must be known in order to improve predictions. At a minimum, measurements of the rotor thrust and tip-path-plane angle are critical to further develop accurate flight acoustic prediction capabilities.

Boyd, D. Douglas, Jr.↗

NASA NTRS1974

Transducers

The use of transducers in the measuring channels of flight test instrumentation systems is discussed. Emphasis is placed on transducers with an electrical output. The physical effects used for producing the electrical outputs are defined. Diagrams of the various types of transducers are included to show the operating principles.

Weirather, L. H.↗

NASA NTRS1985

Orbiter entry aerothermodynamics

The challenge in the definition of the entry aerothermodynamic environment arising from the challenge of a reliable and reusable Orbiter is reviewed in light of the existing technology. Select problems pertinent to the orbiter development are discussed with reference to comprehensive treatments. These problems include boundary layer transition, leeward-side heating, shock/shock interaction scaling, tile gap heating, and nonequilibrium effects such as surface catalysis. Sample measurements obtained from test flights of the Orbiter are presented with comparison to preflight expectations. Numerical and wind tunnel simulations gave efficient information for defining the entry environment and an adequate level of preflight confidence. The high quality flight data provide an opportunity to refine the operational capability of the orbiter and serve as a benchmark both for the development of aerothermodynamic technology and for use in meeting future entry heating challenges.

Ried, R. C.↗

NASA NTRS1985

An airborne multiple-beam 1.4 GHz pushbroom microwave radiometer

A method is described for providing soil moisture measurements from satellites by performing simultaneous measurements across track (the pushbroom approach). The method has the advantage of obtaining the required swath width without sacrificing sensitivity. A prototype Pushbroom Microwave Radiometer developed at NASA's Langley Research Center is described. It is a multibeam L-Band (1413 MHz) radiometer system providing simultaneous cross track measurements. Results of flight tests onboard a P-3 aircraft are discussed.

Harrington, R. F.↗

NASA NTRS1987

Flight and analytical investigations of a structural mode excitation system on the YF-12A airplane

A structural excitation system, using an oscillating canard vane to generate force, was mounted on the forebody of the YF-12A airplane. The canard vane was used to excite the airframe structural modes during flight in the subsonic, transonic, and supersonic regimes. Structural modal responses generated by the canard vane forces were measured at the flight test conditions by airframe-mounted accelerometers. Correlations of analytical and experimental aeroelastic results were made. Doublet lattice, steady state double lattice with uniform lag, Mach box, and piston theory all produced acceptable analytical aerodynamic results within the restrictions that apply to each. In general, the aerodynamic theory methods, carefully applied, were found to predict the dynamic behavior of the YF-12A aircraft adequately.

Goforth, E. A.↗

NASA NTRS1987

The Phase II ROTONET system

The improvements introduced in Phase II of ROTONET, a comprehensive computer program developed at NASA Langley for predicting helicopter noise, are reviewed and demonstrated. The ROTONET functional modules for lifting-rotor performance, lifting-rotor noise, rotor loads, rotor inflow, rotor rigid dynamics, rotor wake geometry, rotor tone noise, and rotor broadband noise are briefly characterized; the construction of an acoustics data base from measurements taken in flight tests of a NASA/MDHC 500E helicopter is described; and the validation tests are summarized. Good agreement between flight-test data and ROTONET predictions is obtained.

Golub, Robert A.↗

NASA NTRS1990

Noise measurements of turboprop airplanes at different overflight elevations

In order to establish criteria for the regulation of propfan aircraft engine noise emissions, measurement tests of overhead flights of a METRO-3 and a FOKKER-50 aircraft were performed. The decibel levels captured by the ground car microphone are tabulated according to the height of the microphone from the ground as the recording vehicle followed the aircraft through the test flight patterns. Microphone heights of 1.5 and 10 meters from the ground are recorded and correlated to the flight altitudes of the aircraft, which ranged from 5182-6401 meters.

Mueller, K.↗

NASA NTRS2011

Measured Sonic Boom Signatures Above and Below the XB-70 Airplane Flying at Mach 1.5 and 37,000 Feet

During the 1966-67 Edwards Air Force Base (EAFB) National Sonic Boom Evaluation Program, a series of in-flight flow-field measurements were made above and below the USAF XB-70 using an instrumented NASA F-104 aircraft with a specially designed nose probe. These were accomplished in the three XB-70 flights at about Mach 1.5 at about 37,000 ft. and gross weights of about 350,000 lbs. Six supersonic passes with the F-104 probe aircraft were made through the XB-70 shock flow-field; one above and five below the XB-70. Separation distances ranged from about 3000 ft. above and 7000 ft. to the side of the XB-70 and about 2000 ft. and 5000 ft. below the XB-70. Complex near-field "sawtooth-type" signatures were observed in all cases. At ground level, the XB-70 shock waves had not coalesced into the two-shock classical sonic boom N-wave signature, but contained three shocks. Included in this report is a description of the generating and probe airplanes, the in-flight and ground pressure measuring instrumentation, the flight test procedure and aircraft positioning, surface and upper air weather observations, and the six in-flight pressure signatures from the three flights.

Maglieri, Domenic J.↗

NASA NTRS2017

Sound Diffraction Modeling of Rotorcraft Noise Around Terrain

A new computational technique, Wave Confinement (WC), is extended here to account for sound diffraction around arbitrary terrain. While diffraction around elementary scattering objects, such as a knife edge, single slit, disc, sphere, etc. has been studied for several decades, realistic environments still pose significant problems. This new technique is first validated against Sommerfeld's classical problem of diffraction due to a knife edge. This is followed by comparisons with diffraction over three-dimensional smooth obstacles, such as a disc and Gaussian hill. Finally, comparisons with flight test acoustics data measured behind a hill are also shown. Comparison between experiment and Wave Confinement prediction demonstrates that a Poisson spot occurred behind the isolated hill, resulting in significantly increased sound intensity near the center of the shadowed region.

Stephenson, James H.↗

NASA NTRS2002

Power Measurement Errors on a Utility Aircraft

Extensive flight test data obtained from two recent performance tests of a UH 60A aircraft are reviewed. A power difference is calculated from the power balance equation and is used to examine power measurement errors. It is shown that the baseline measurement errors are highly non-Gaussian in their frequency distribution and are therefore influenced by additional, unquantified variables. Linear regression is used to examine the influence of other variables and it is shown that a substantial portion of the variance depends upon measurements of atmospheric parameters. Correcting for temperature dependence, although reducing the variance in the measurement errors, still leaves unquantified effects. Examination of the power difference over individual test runs indicates significant errors from drift, although it is unclear how these may be corrected. In an idealized case, where the drift is correctable, it is shown that the power measurement errors are significantly reduced and the error distribution is Gaussian. A new flight test program is recommended that will quantify the thermal environment for all torque measurements on the UH 60. Subsequently, the torque measurement systems will be recalibrated based on the measured thermal environment and a new power measurement assessment performed.

Bousman, William G.↗

NASA NTRS1998

Full Flight Envelope Direct Thrust Measurement on a Supersonic Aircraft

Direct thrust measurement using strain gages offers advantages over analytically-based thrust calculation methods. For flight test applications, the direct measurement method typically uses a simpler sensor arrangement and minimal data processing compared to analytical techniques, which normally require costly engine modeling and multisensor arrangements throughout the engine. Conversely, direct thrust measurement has historically produced less than desirable accuracy because of difficulty in mounting and calibrating the strain gages and the inability to account for secondary forces that influence the thrust reading at the engine mounts. Consequently, the strain-gage technique has normally been used for simple engine arrangements and primarily in the subsonic speed range. This paper presents the results of a strain gage-based direct thrust-measurement technique developed by the NASA Dryden Flight Research Center and successfully applied to the full flight envelope of an F-15 aircraft powered by two F100-PW-229 turbofan engines. Measurements have been obtained at quasi-steady-state operating conditions at maximum non-augmented and maximum augmented power throughout the altitude range of the vehicle and to a maximum speed of Mach 2.0 and are compared against results from two analytically-based thrust calculation methods. The strain-gage installation and calibration processes are also described.

Conners, Timothy R.↗

NASA NTRS1981

In-flight jet engine noise measurement system

An instrumentation system in flight tests for noise research is described which utilizes miniature transducers to measure low-amplitude, high-frequency fluctuating pressures in a jet engine mounted under the wing of a turboprop aircraft. The system employs a rotor-mounted FM telemeter to acquire data from eight fan-blade-mounted transducers which are subjected to up to 75,000 g's of loading. Data is transmitted from the rotor to an antenna mounted in the inlet-duct wall using a low-power, close-coupled RF link. The blade pressures and other inlet and stator-vane fluctuating pressures are recorded on airborne, magnetic-tape recorders. The flight instrumentation described also includes PCM techniques to encode and record a variety of quasi-static measurements to provide engine and aircraft performance data. The instrumentation and experimental measurements are of value to an improved understanding of noise sources in jet engines and for the advancement of jet-engine ground noise testing techniques.

Knight, V. H., Jr.↗

NASA NTRS2017

Control and Non-Payload Communications (CNPC) Prototype Radio Validation Flight Test Report

This report provides an overview and results from the unmanned aircraft (UA) Control and Non-Payload Communications (CNPC) Generation 5 prototype radio validation flight test campaign. The radios used in the test campaign were developed under cooperative agreement NNC11AA01A between the NASA Glenn Research Center and Rockwell Collins, Inc., of Cedar Rapids, Iowa. Measurement results are presented for flight tests over hilly terrain, open water, and urban landscape, utilizing radio sets installed into a NASA aircraft and ground stations. Signal strength and frame loss measurement data are analyzed relative to time and aircraft position, specifically addressing the impact of line-of-sight terrain obstructions on CNPC data flow. Both the radio and flight test system are described.

Shalkhauser, Kurt A.↗