Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel Cycle Modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

AGR-5/6/7 Capsule 1 Temperature Re-analysis_Grant Hawkes_Final

Slides for Gas-Cooled Reactor AGR-5/6/7 Thermal Model with Non-Uniform Gas Gaps. Includes investigation of offset through modeling and experimental results, ABAQUS finite element model created for the entire test train, Capsule 1 information, Three irradiation dates to compare the thermal model with the working thermocouples (TCs), Offset distances and direction of offset for the top and bottom of the graphite holder with computer runs, determination of offset by the root mean square error (RMSE) between the TCs and model predtictions, and the results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Coupled Experimental and Simulation Approach to Investigate the Impact of Grain Growth, Amorphization, and Grain Subdivision in Accident Tolerant U 3 Si 2 Light Water Reactor Fuel

Triuranium disilicide (U 3 Si 2 ) is being considered as an alternative accident tolerant fuel (ATF) due to its higher thermal conductivity. However, there is uncertainty in its use due to a lack of irradiation data at light water reactor (LWR) conditions. In this project, we used an integrated experimental and simulation approach to answer two significant questions pertaining to U 3 Si 2 that were not investigated by the Fuel Cycle Research and Development (FCRD) and Nuclear Energy Advanced Modeling and Simulation (NEAMS) programs: (1) Will grain growth in the hotter portions of the fuel significantly impact U 3 Si 2 LWR fuel behavior? (2) Under what conditions do grain subdivision and amorphization occur in U 3 Si 2 and will either occur at LWR conditions? Our approach to answer these questions used in situ ion irradiation and annealing to investigate grain growth, grain subdivision, and amorphization, along with mesoscale simulations using the MARMOT tool. We found that while the grain boundary mobility of U 3 Si 2 is larger than that of UO 2 , grain growth in U 3 Si 2 fuel pellets will be less than in UO 2 and may be neglected due to the lower thermal conductivity and thus lower centerline temperature. We also found that amorphization will not occur in U 3 Si 2 above 600 K, such that it is not likely to occur at typical LWR operating conditions. Grain subdivision will occur at LWR conditions and will likely occur at lower burnups than in UO 2 .

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Fuel Performance Modeling Status Update and Potential Model Improvements

Fuel performance modeling status update and potential model improvements overview of TRISO fuel performance modeling codes PARFUME/BISON, AGR experiment support, potential modeling improvements, BISON smeared cracking model, BISON fission product source term, and AGR-3/4 reirradiation heating test.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Model-Based Analysis of Electric Drive Options for Medium-Duty Parcel Delivery Vehicles: Preprint

Medium-duty vehicles are used in a broad array of fleet applications, including parcel delivery. These vehicles are excellent candidates for electric drive applications due to their transient-intensive duty cycles, operation in densely populated areas, and relatively high fuel consumption and emissions. The National Renewable Energy Laboratory (NREL) conducted a robust assessment of parceldelivery routes and completed a model-based techno-economic analysis of hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle configurations. First, NREL characterized parcel delivery vehicle usage patterns, most notably daily distance driven and drive cycle intensity. Second, drive-cycle analysis results framed the selection of drive cycles used to test a parcel delivery HEV on achassis dynamometer. Next, measured fuel consumption results were used to validate simulated fuel consumption values derived from a dynamic model of the parcel delivery vehicle. Finally, NREL swept a matrix of 120 component size, usage, and cost combinations to assess impacts on fuel consumption and vehicle cost. The results illustrated the dependency of component sizing on drive-cycle intensityand daily distance driven and may allow parcel delivery fleets to match the most appropriate electric drive vehicle to their fleet usage profile.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Comparison Between Pin-by-Pin Subchannel and System Level Thermal Hydraulic Results for High Burnup Loss-of-Coolant Applications

This milestone report summarizes recent work to investigate higher fidelity modeling and simulation practices for large-break loss-of-coolant accident (LBLOCA) analysis in high-burnup pressurized water reactor (PWR) cores. Because of current industry interest in extending fuel cycle lengths ranging from 18 to 24-months, the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program has been investigating the susceptibility of high-burnup core designs to fuel fragmentation, release, and dispersal (FFRD) during accident conditions such as LBLOCA. This work has prioritized developing and demonstrating a methodology for calculating core-wide susceptibility to FFRD and addressing uncertainties identified in the analysis and the US Nuclear Regulatory Commission (NRC) Research Information Letter on FFRD. Part of this investigation seeks to quantify differences between system-level thermal hydraulic behavior and higher fidelity subchannel modeling methods to identify potential safety concerns or opportunities to minimize FFRD susceptibility. To this end, the NEAMS subchannel code, CTF, is being used, along with the NRC system analysis code TRACE, for analysis of LBLOCA in a core containing high-burnup fuel. This project includes two thrusts: (1) improving on the existing TRACE model for a 4-loop PWR for LBLOCA so that the model is higher fidelity and consistent with current USNRC best practices, and (2) using CTF to perform pin-resolved modeling of the core region of the reflood phase of a LBLOCA in a high-burnup PWR.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Material Protection, Accounting, and Control Technologies (MPACT): Modeling and Simulation Roadmap

The development of sustainable advanced nuclear fuel cycles is a long-term goal of the Office of Nuclear Energy’s (DOE-NE) Fuel Cycle Technologies program. The Material Protection, Accounting, and Control Technologies (MPACT) campaign is supporting research and development (R&D) of advanced instrumentation, analysis tools, and integration methodologies to meet this goal. This advanced R&D is intended to facilitate safeguards and security by design of fuel cycle facilities. The lab-scale demonstration of a virtual facility, distributed test bed, that connects the individual tools being developed at National Laboratories and university research establishments, is a key program milestone for 2020. These tools will consist of instrumentation and devices as well as computer software for modeling. To aid in framing its long-term goal, during FY16, a modeling and simulation roadmap is being developed for three major areas of investigation: (1) radiation transport and sensors, (2) process and chemical models, and (3) shock physics and assessments. For each area, current modeling approaches are described, and gaps and needs are identified.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Developing a Validation Methodology for Expert-Informed Bayesian Network Models Supporting Nuclear Nonproliferation Analysis

Under the auspices of Pacific Northwest National Laboratory’s Signature Discovery Initiative (SDI), the research team developed a series of Bayesian Network models to assess multi-source signatures of nuclear programs. A Bayesian network is a mathematical model that can be used to marshal evidence to assess competing hypotheses. The purpose of the models was to allow non-expert analysts to benefit from the use of expert-informed mathematical models to assess nuclear programs, because such assessments require significant technical expertise ranging from the nuclear fuel cycle, construction and engineering, imagery analysis, and so forth. One such model developed under this research was aimed at assessing the consistency of open-source information about a nuclear facility with the facility’s declared use. The model incorporates factors such as location, security and safety features among others identified by subject matter experts as crucial to their assessments. The model includes key features, observables and their relationships. The model also provides documentation, which serves as training materials for the non-experts.

White, Amanda M.↗

Limit cycle vibrations in turbomachinery

The focus is on an examination of rotordynamic systems which are simultaneously susceptible to limit cycle instability and subharmonic response. Characteristics of each phenomenon are determined as well as their interrelationship. A normalized, single mass rotor model is examined as well as a complex model of the high pressure fuel turbopump and the Space Shuttle Main Engine. Entrainment of limit cycle instability by subharmonic response is demonstrated for both models. The nonuniqueness of the solution is also demonstrated.

Ryan, S. G.↗

Single-size and cluster dynamics modeling of intra-granular fission gas bubbles in UO 2

For this work, we perform simulations of intra-granular fission gas bubble evolution in UO 2 using both a relatively simple, computationally inexpensive single-size model and a detailed cluster dynamics model. Simulations encompass 36 experimental cases from 4 different databases, covering various temperature and burnup levels. We systematically compare results from the two models to each other and to post-irradiation experimental data of bubble average size and number density. Overall, the model-to-model comparisons reveal an excellent agreement across the set of simulations. This outcome indicates that, in spite of the underlying assumptions, the single-size model provides a good approximation of the complex physical behavior that is more rigorously described by the cluster dynamics model. Qualitatively, both models reproduce the trends of the experimental data with temperature and burnup correctly. Quantitatively, calculated results are either in good agreement with the data or within errors that appear consistent with the inherent uncertainties. Moreover, for the single-size model, we demonstrate and assess a multiscale approach whereby values for the fission gas atom diffusion coefficient from separate atomistic calculations are used. Systematic comparisons to experimental data point out a credible accuracy of the multiscale model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Gamma and Neutron Measurement and Modeling of Irradiated TRISO Fuel

Given the unique characteristics of the PBR fuel cycle, both gamma and neutron measurements are expected to play important roles in performing and maintaining nuclear material control and accounting for spent pebbles to safeguard the fuel cycle. Given the lack of irradiated pebbles in the US, a variety of irradiated TRISO fuel samples with wide ranges of burnups and cooling times available at ORNL were used in this work. A large number of gamma and neutron measurements have been performed on these samples to collect data to test the various detectors and to benchmark the computer models to simulate the depletion and decay of the fuel and the measurements themselves. Two neutron detectors, including a custom-made detector and the Very High-Performance Neutron Multiplicity Counting, were used to measure the neutrons emitted by these TRISO samples. Three gamma spectrometry detectors, including an HPGe and the M400 CZT detector, were used to measure gamma-ray emissions from these samples. The M400 was recently adopted by the IAEA for fresh uranium measurements, but it was tested for spent fuel measurements prior to this project. Detailed MCNP models were developed to simulate these neutron and gamma measurements. Some GADRAS models were also developed to cross check the MCNP models for the gamma measurements. It was found challenging to perform neutron measurements in the hot cell due to the high background counts. Close agreements were observed between the simulated and measured neutron count rates in both detectors’ measurements of californium calibration sources. Both the HPGe and M400 detectors were able to measure the 604 and 662 keV peaks from these samples, which are the two most important peaks used to infer fuel burnup. Although the M400 detector did not have nearly good energy resolution and did not detect some of the minor peaks as the HPGe detector, it was found to be capable of handling significantly higher dose rates than HPGe. Given the complexities in the TRISO samples (e.g., different samples sizes) and uncertainties in the alignments between the detector and the TRISO fuel inside the containers, large scatters were found between the peak area rates and the samples’ burnups. However, the 604/662 peak ratios were found to trend well with the samples’ burnups among most samples in both measured and simulated results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Updated estimation of energy efficiencies of U.S. petroleum refineries.

Evaluation of life-cycle (or well-to-wheels, WTW) energy and emission impacts of vehicle/fuel systems requires energy use (or energy efficiencies) of energy processing or conversion activities. In most such studies, petroleum fuels are included. Thus, determination of energy efficiencies of petroleum refineries becomes a necessary step for life-cycle analyses of vehicle/fuel systems. Petroleum refinery energy efficiencies can then be used to determine the total amount of process energy use for refinery operation. Furthermore, since refineries produce multiple products, allocation of energy use and emissions associated with petroleum refineries to various petroleum products is needed for WTW analysis of individual fuels such as gasoline and diesel. In particular, GREET, the life-cycle model developed at Argonne National Laboratory with DOE sponsorship, compares energy use and emissions of various transportation fuels including gasoline and diesel. Energy use in petroleum refineries is key components of well-to-pump (WTP) energy use and emissions of gasoline and diesel. In GREET, petroleum refinery overall energy efficiencies are used to determine petroleum product specific energy efficiencies. Argonne has developed petroleum refining efficiencies from LP simulations of petroleum refineries and EIA survey data of petroleum refineries up to 2006 (see Wang, 2008). This memo documents Argonne's most recent update of petroleum refining efficiencies.

02 PETROLEUM↗

Numerical Model of Thermoelectric Topping Cycle of Coal-Fired Power Plant

Traditional fossil fuel power generation process typically has low efficiency. Large amount of the energy loss in Rankine cycle steam turbines (ST) is due to the temperature difference between the combustion flame temperature ~2250 K (adiabatic) and the high pressure steam temperature up to 900 K. However, some of this energy can be harvested using solid-state thermoelectric (TE) power generators which are placed into the gap between the flame temperature and the steam temperature that produce additional electrical power. This study investigates the potential placement of TE on water tube wall inside a boiler at a coal-fired power plant. Three-dimensional (3D) numerical model of a simplified TE module is developed, and hot gas temperature and steam temperature from the boiler are used as boundary conditions at the hot side and cold side of the TE. The numerical results are compared with analytical calculations. The 3D effects of the thermal spreading in the TE module are investigated. Parameters such as TE leg cross section area and TE fill factor are examined in order to maximize the electrical power production of the TE without sacrificing the boiler efficiency (i.e., reducing the steam temperature). The study also looks into the various locations inside the boiler that have good potential for TE installation.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

TREAT Transient Test Reactor Restart Status

Transient testing involves placing nuclear fuel or material into the core of a nuclear reactor designed to operate at high power for a short time, and subjecting the nuclear fuel or material to short bursts of intense, high power radiation. After the experiment is completed, the fuel or material is analyzed to determine the effects of the radiation. The results are then used in fuel or material design and/or qualification. Transient testing is required for essentially all nuclear fuel design and qualification efforts to learn how nuclear fuel will respond during accidents involving transient overpower and/or under cooling events. For example, nuclear fuel may fragment when exposed to higher than normal power. This fragmentation can cause unacceptable performance. Transient testing is also needed to validate performance models for nuclear fuel and materials. These models, when validated, will dramatically shorten the development and qualification life cycle for nuclear fuels, supporting rapid development of low emissions, reliable power generation. In the past, transient testing was primarily done in facilities that no longer exist. The U.S. Department of Energy evaluated how to provide the required transient testing capability and, following completion of the National Environmental Policy Act process, they selected the Transient Reactor Test (TREAT) facility to resume transient testing. TREAT is located at Idaho National Laboratory (INL). The TREAT reactor was used from 1959 to 1994 to conduct more than 2,500 nuclear fuel transient tests, and was placed in standby in 1994. TREAT is capable of transients in excess of 19 GW. The paper describes the progress towards restart. The restart efforts have revealed that the plant fuel and equipment is acceptable for future operations. The safety basis development, procedures, and training are well under way. Experiment capability preparations are in progress. Reactor startup is anticipated no later than 2018. (author)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Design and modeling for hydrogen fuel cell conversion of parcel delivery trucks

With an emphasis on reducing fossil fuel consumption and emissions, major delivery service corporations have begun deploying and operating Class 6 zero emissions delivery vans. Battery electric delivery vans are currently available, but their range is a limitation and doesn’t offer flexibility in assigning vehicles to delivery routes. Fuel cell hybrid delivery vans offer a zero emissions solution with extended range and route planning flexibility. In a competitive market, a delivery van design that trades the fuel cell and battery size, performance, and cost is critical to the success and adoption of these zero emissions trucks. This paper outlines a systematic approach using real world operational data and duty cycles to properly size the fuel cell and battery for a zero emissions hybrid delivery van. The approach uses real world GPS data to define routes and duty cycles, along with vehicle powertrain models to assess performance capabilities. Furthermore, the study suggests that a 32 kW fuel cell power system paired with a 49 kWh battery energy storage system and 15 kg of hydrogen storage is a desired option to complete the most demanding parcel and delivery duty cycles.

08 HYDROGEN↗

Reactor physics benchmark of Westinghouse PWR core design suite for high burnup/high enrichment fuel - Part 2: 2D and 3D core simulations

Westinghouse has performed a comprehensive set of code-to-code benchmark comparisons to corroborate application of its state-of-the-art NEXUS-based code suite to high burnup and high enrichment (HB/HE) fueled PWR core design and reload analysis. The benchmark consisted of a progression in complexity from modeling single 2D pin cells, through 2D lattices and finally to whole core 2D and then 3D scenarios. The accompanying paper (Part 1) presented the results for a variety of pin cell and lattices representative of high energy cores and established the ability of the MPACT code to accurately match the predictions of the Monte-Carlo code SERPENT2 such that the former may be used as a surrogate reference code in spatially complex whole core modeling applications where using Monte-Carlo methods is somewhat impractical. This paper focuses on comparisons at the whole core level using a representative high power density 3-loop Westinghouse NSSS core operating for 24 month cycles employing high enriched fuel with use of combined burnable absorbers to hold down excess reactivity. The evolution of the core reactivity and power distribution characteristics throughout the cycle are calculated using the Westinghouse NEXUS-based code suite and compared to the results using MPACT. The results of this whole core benchmark confirm the conclusions that the Westinghouse code suite accurately models HB/HE fuel designs, with very good prediction of core reactivity and power distribution throughout the cycle. The industry can be confident that the NEXUS code system can be deployed to support PWR reload safety and operational analyses for cores featuring HB/HE fuel and 24-month cycle operation. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Report on Assessment of Advanced Reactor Fuel Performance

Three activities have been performed in FY 2019 to support the Advanced Fuel Cycle Campaign, which include assessment of annular fuel performance in an ultra-high burnup sodium-cooled reactor (SFR), modeling of annular fuel behavior during a transient scenario, and feasibility of a sustainable closed fuel cycle utilizing melt-refining process. Annular fuel performance parameters, including temperature profile, swelling strain, and cumulative damage fraction (CDF), in a 3000 MWt Sustainable Sodium-cooled Fast Reactor (SSFR) were assessed using the BISON fuel performance code. The SSFR is once-through ultra-long-life core based on a 34-batch fuel management scheme with 1.5-year cycle length. The fuel residence time in the SSFR is 51 years and the average discharged burnup is about 30%. Annular fuel has potential to irradiate for ultra-high burnup without major fuel-cladding mechanical interaction. This feature is achieved by using a low smeared density (~55%). In the SSFR design, however, 75% smeared density and a thick fuel pin were preferred to maintain criticality for 51 years. Due to the high smeared density and thick fuel pin configuration, the annular fuel was predicted to suffer premature cladding failure before reaching the discharge burnup of the SSFR. The current fuel creep model predicts a prominent creep strain due to gravity over the half-century irradiation, which may significantly affect the evolution of CDF. Thus, in order to use the annular fuel in an ultra-high burnup core such as the SSFR, a low smeared density and thin annular fuel is strongly recommended.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Model of Hydrogen Solubility in Palladium-Silver Alloys

Fusion fuel cycle designs depend on palladium and palladium-silver alloys. The selective permeability of these is used to separate hydrogen isotopes from other elements. Predicting the solubility of hydrogen isotopes in palladium-silver alloys is important for the design of key unit operations for tritium processing. This paper presents a model of hydrogen isotope solubility in palladium and palladium-silver alloys based on Guggenheim’s quasichemical lattice theory. The model parameters were determined as functions of isotope molecular weight and the silver content of the alloy. The model predicts reasonable values for the solubility of protium, deuterium, and tritium over a wide range of temperatures, pressures, and alloy compositions.

08 HYDROGEN↗