Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fuel cladding”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Correlation between Interface Microstructure and Bond Strength of Al6061/Al6061 HIP-Bonded Plates for Fuel Cladding Application

The effects of hot isostatic pressing (HIP) processing parameters on microstructure and bond strength of Al6061/Al6061 plate interfaces were systemically investigated at the micro- and nanoscale. The HIP bonding of the two aluminum plates was performed at four temperatures: 350°C, 400°C, 450°C, and 560°C. The results reveal the formation of micron scaled Mg 2 Si precipitate and uniform nano scaled Mg 2 Al 2 O 5 oxide at the interface. The formation of Mg 2 Al 2 O 5 is closely associated with the fast bulk diffusion of Mg from the Al matrix to the amorphous Al 2 O 3 /Al interface and subsequent reaction between Mg and Al 2 O 3 . Finally, the highest and lowest bond strengths were observed in samples HIP bonded at 450°C and 350°C, respectively.

36 MATERIALS SCIENCE↗

Continuum model for hydrogen pickup in zirconium alloys of LWR fuel cladding

A continuum model for calculating the time-dependent hydrogen pickup fractions in various Zirconium alloys under steam and pressured water oxidation has been developed in this paper. Using only one fitting parameter, the effective hydrogen gas partial pressure at the oxide surface, a qualitative agreement is obtained between the predicted and previously measured hydrogen pickup fractions. The calculation results therefore demonstrate that H diffusion through the dense oxide layer plays an important role in the hydrogen pickup process. Finally, the limitations and possible improvement of the model are also discussed.

36 MATERIALS SCIENCE↗

Thermochemical Compatibility and Oxidation Resistance of Advanced LWR Fuel Cladding

We assessed the thermochemical compatibility of potential replacement cladding materials for zirconium alloys in light water reactors. Considered were FeCrAl steel (similar to Kanthal APMT), Nb-1%Zr (similar to PWC-11), and a hybrid SiC-composite with a metallic barrier layer. The niobium alloy was also seen as requiring an oxidation protective layer, and a diffusion silicide was investigated. Metallic barrier layers for the SiC-composite reviewed included a FeCrAl alloy, Nb-1%Zr, and chromium. Thermochemical calculations were performed to determine oxidation behavior of the materials in steam, and for hybrid SiC-composites possible interactions between the metallic layer and SiC. Additionally, experimental exposures of SiC-alloy reaction couples at 673K, 1073K, and 1273K for 168 h in an inert atmosphere were made and microanalysis performed. Whereas all materials were determined to oxidize under higher oxygen partial pressures in the steam environment, these varied by material with expected protective oxides forming. Finally, the computed and experimental results indicate the formation of liquid phase eutectic in the FeCrAl-SiC system at the higher temperatures.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Understanding corrosion and hydrogen pickup of zirconium fuel cladding alloys: The role of oxide microstructure, porosity, sub-oxides, and second-phase particles - 2016-0071

We used a range of advanced microscopy techniques to study the microstructure, nanoscale chemistry, and porosity in zirconium alloys at different stages of oxidation. Samples from both autoclave and in-reactor conditions were available, including ZIRLO{sup TM}, Zr-1.0Nb, and Zr-2.5Nb samples with different heat treatments. Scanning transmission electron microscopy (STEM), transmission Kikuchi diffraction (TKD), and automated crystal orientation mapping with TEM were used to study the grain structure and phase distribution. Significant differences in grain morphology were observed between samples oxidized in the autoclave and in-reactor, with shorter, less well-aligned monoclinic grains and more tetragonal grains in the neutron-irradiated samples. A combination of energy-dispersive X-ray mapping in STEM and atom probe tomography analysis of second-phase particles (SPPs) can reveal the main and minor element distributions respectively. Neutron irradiation seems to have little effect on promoting fast oxidation or dissolution of β-niobium precipitates but encourages the dissolution of iron from Laves-phase precipitates. An electron energy-loss spectroscopy (EELS) analysis of the oxidation state of niobium in β-niobium SPPs in the oxide revealed the fully oxidized Nb{sup 5+} state in SPPs deep into the oxide but Nb{sup 2+} in crystalline SPPs near the metal-oxide interface. EELS analysis and automated crystal orientation mapping with TEM revealed Widmanstatten-type suboxide layers in some samples with the hexagonal ZrO structure predicted by ab initio modeling. The combined thickness of the ZrO suboxide and oxygen-saturated layers at the metal-oxide interface correlated well to the instantaneous oxidation rate, suggesting that this oxygen-rich zone is part of the protective oxide that is rate limiting in the transport processes involved in oxidation. Porosity in the oxide had a major influence on the overall rate of oxidation, and there was more porosity in the rapidly oxidizing annealed Zr-1.0Nb alloy than in either the recrystallized alloy or the similar alloy exposed to neutron irradiation. (authors)

36 MATERIALS SCIENCE↗

High Temperature and Pressure Steam-H 2 Interaction with Candidate Advanced LWR Fuel Claddings

This report summarizes the work completed to evaluate cladding materials that could serve as improvements to Zircaloy in terms of accident tolerance. This testing involved oxidation resistance to steam or H 2 -50% steam environments at 800-1350°C at 1-20 bar for short times. A selection of conventional alloys, SiC-based ceramics and model alloys were used to explore a wide range of materials options and provide guidance for future materials development work. Typically, the SiC-based ceramic materials, alumina-forming alloys and Fe-Cr alloys with ≥25% Cr showed the best potential for oxidation resistance at ≥1200°C. At 1350°C, FeCrAl alloys and SiC remained oxidation resistant in steam. Conventional austenitic steels do not have sufficient oxidation resistance with only ≈18Cr-10Ni. Higher alloyed type 310 stainless steel is protective but Ni is not a desirable alloy addition for this application and high Cr contents raise concern about α' formation. Higher pressures (up to 20.7 bar) and H 2 additions appeared to have a limited effect on the oxidation behavior of the most oxidation resistant alloys but higher pressures accelerated the maximum metal loss for less oxidation resistant steels and less metal loss was observed in a H 2 -50%H 2 O environment at 10.3 bar. As some of the results regarding low-alloyed FeCrAl and Fe-Cr alloys were unexpected, further work is needed to fundamentally understand the minimum Cr and Al alloy contents needed for protective behavior in these environments in order to assist in alloy selection and guide alloy development.

36 MATERIALS SCIENCE↗

Deformation Behavior in Neutron Irradiated Generation II FeCrAl Alloys for Accident Tolerant Fuel Cladding

Preliminary work has been completed to evaluate the deformation behavior of the Generation II FeCrAl alloy class. The Generation II alloy, C35M, was neutron irradiated within the High Flux Isotop e Reactor followed by post-irradiation examination to evaluate the mechanical properties, irradiated microstructure, deformation modes, and deformation microstructure. Complementary characterization techniques were used in this evaluation. It was found tha t aft er irradiation to1.8 dpa at 364 °C that the C35M specimen failed in a ductile manner. The observed deformation microstructure showed a high density of line dislocations, dislocation networks, and dislocation pile-ups. The observed performance and stru cture s are consistent with literature studies on high-Cr FeCr alloys that were thermally aged at 500°C. The observed results suggest that Generation II FeCrAl alloys retain ductility under low-dose, prototypical LWR irradiation conditions.

36 MATERIALS SCIENCE↗