SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
The durability of the 490 N AJ10-221 engine is characterized on the basis of data from 93 tests and a total firing life of 6.3 hr. For the three Ir/Re chambers tested, no limiting conditions were encountered in the 43,379 sec and 229 test thermal cycles. A wide range of off nominal operating conditions was successfully demonstrated.
Developing efficient and stable electrocatalysts for the acidic oxygen evolution reaction (OER) is vital for advancing proton exchange membrane water electrolysis (PEMWE) technologies. Here, in this study, we report a flux synthesis of nitrogen-doped Ti–Ru rutile-type solid-solution oxides (M-TiRu 4 ) using molten NaNO 3 as the flux medium. The flux medium promotes the low-temperature conversion of TiN to rutile TiO 2 , while in situ-formed RuO 2 nanoparticles facilitate lattice templating and couple with interfacial ion migration, enabling the formation of homogeneous solid solutions with abundant lattice heterogeneity. Simultaneously, nitrogen atoms are stably incorporated into the lattice of solid solutions, inducing bandgap narrowing, which enhances electronic conductivity. The developed M-TiRu 4 catalyst exhibits exceptional acidic OER performance, delivering a low overpotential of 194 mV at 10 mA cm −2 , superior durability over 600 h, and a Ru mass activity 7.8 times that of commercial RuO 2 . At the device level, M-TiRu 4 enables PEMWE operation at 1.64 V @ 2 A cm −2 and maintains stable performance at 500 mA cm −2 for 200 h with a minimal degradation rate of 20 µV h −1 . This work demonstrates a robust approach for designing high-performance, durable acidic OER catalysts via synergistic lattice and electronic structure engineering, paving the way for next-generation water-splitting technologies.
This paper addresses the challenge of tritium inventory management in ITER and future fusion reactors, highlighting the importance of accurate tritium measurement and its spatial distribution within the vacuum vessel. Given ITER’s operational constraints, especially the limit on tritium retention, precise measurement is essential for both safety and regulatory compliance. To tackle these questions, the paper presents the T-monitor diagnostic system developed by Forschungszentrum Jülich, which uses Laser-Induced Desorption (LID) in combination with Diagnostic Residual Gas Analysis (DRGA) to measure hydrogen isotope concentrations on the surface of divertor tiles. The system integrates a high-power laser, advanced optical components, and a Fast Scanning Mirror Unit (FSMU) for accurate laser spot positioning with rapid response. Designed to measure in situ tritium retention, the diagnostic provides high-resolution spatial mapping, vital for evaluating detritiation strategies. The laser heating process increases the divertor surface temperature to 1600 K within the laser spot, promoting hydrogen isotope desorption. Accurate measurements require the precise control of laser parameters, including pulse duration and spot size, with a target relative accuracy of 20%. The optical design includes both in-vessel and ex-vessel components, such as durable high-reflectivity mirrors made of gold and copper, selected not only for their infrared performance but also for their transmission of visible wavelengths for observation purposes. To protect optical components from contamination, a pneumatic shutter is used.
While NASA Glenn Research Center's "Generation 10" 4H-SiC Junction Field Effect Transistor (JFET) integrated circuits (ICs) have uniquely demonstrated 500 °C electrical operation for durations of over a year, this experimental work has also revealed that physical cracking of chip dielectric passivation layers ultimately limits extreme-environment operating lifetime [1-3]. The prevention of such dielectric passivation cracks should therefore improve IC high temperature durability and yield, leading to more beneficial technology adoption into aerospace, automotive, and energy systems. This report describes Generation 10.2, 11.1, and 11.2 die tested under unbiased and unpackaged accelerated age testing at 500 °C, 600 °C, 720 °C, and 800 °C in air-atmosphere ovens for 100- and 200-hour duration. Additional samples were separately subjected to 10 thermal cycles between the same high temperatures (with 10-hour high-temperature soak each cycle) and 50 °C. It is shown that having two stoichiometric Si3N4 layers in the interconnect dielectric stack substantially decreases the amount of dielectric cracking observed following these oven tests.
As part of ARPA-E’s High Intensity Thermal Exchange through Materials and Manufacturing Processes (HITEMMP) program, this project sought to develop novel heat exchanger (HX) capabilities to enable efficient and power dense power generation cycles. This class of HX comes under the category of ceramic/composite materials with the higher temperature goal in the program of ≥1100 °C inlet temperature operation. The enabling capability of this effort is the use of glass-ceramic matrix composite (GCMC) material which provides the high temperature durability of a ceramic, the flaw tolerance of a composite, a significantly faster and lower cost manufacturing process than conventional matrix CMCs and very low porosity levels < 0.5%. For thin-walled HX structures and the need to minimize leakage, the low porosity differentiator is particularly important. RTRC has prior experience with this material system and in the current project advanced the component design and manufacturing methods into new territory to produce features required for effective heat exchange under high pressures. In this approach, silicon carbide fiber is fabricated into a fiber preform using various textile processes. Graphite tooling is used both during the build-up of the fiber preform (interior tooling) and after the fiber preform has been completed (exterior tooling). This tooling assembly is heated to high temperature in an environment that has been evacuated and backfilled with inert gas. A reservoir of specialty glass is present and once the desired temperature has been reached to achieve the desired glass viscosity, an actuator distributes the glass throughout the fiber preform using passageways which are part of the tooling design in a process known as glass transfer molding. After the tooling has been removed, the composite is heat treated to convert the amorphous glass to a crystalline ceramic, providing improved properties. The project was divided into three phases focusing on the following: 1) 10 kW HX design and coupon-level tube sheet fabrication, 2) 10 kW HX fabrication, 3) 50 kW HX fabrication. During Budget Period 1 (BP1), additional risks were encountered and the need for additional funds was agreed upon by ARPA-E program leadership. Due to a variety of factors, the contract modification required nominally 18 months to execute at which time the HITEMMP program was effectively concluding. Because of this and the time that would be required to perform BP2 tasks, it was decided to conclude the project at the end of BP1. During the design of the 10 kW HX, manufacturing constraints were learned and incorporated, leading to a revised configuration for the fiber preform and HX. Heat exchange and pressure drop predictions also played a role in modifying the original design concept to be a higher aspect ratio shell-and-tube HX, simplifying the manufacturing process and improving the heat exchanger performance. Good gravimetric and volumetric thermal power densities of 11.2 kW/kg and 10,200 kW/m3 for the entire HX were projected that involved thermo-structural Finite Element Analysis to determine the structural mass needed for the high operation pressures of 250 bar cold inlet and 80 bar hot inlet. Fiber preforms using textile processes were produced for multiple headered tube sheets. Additional challenges were encountered during the glass transfer molding step for which solutions were identified, but programmatics did not allow them to be implemented in BP1. While complete HX test articles were not fabricated, the benefits of this GCMC material for a variety of high temperature applications remain.
Clean and sustainable energy is becoming increasingly crucial to tackle the current energy crisis. However, the intermittent nature of renewable energy sources presents a challenge for their effective implementation. Redox flow batteries (RFBs) have emerged as a promising solution to this problem, as they can help enhance the stability of grid networks and promote the use of renewable energy sources. RFBs are highly modular and scalable systems that can be customized to meet the power and energy requirements of different renewable energy plants. Moreover, they offer several advantages over conventional battery technologies, including cost and safety concerns. However, conventional RFBs have limited energy densities due to the low solubility of their active species in electrolyte. To overcome this limitation, semi-solid (SSRFBs) and redox targeting (RTFBs) flow batteries have been proposed. These systems feature high concentrations of active species and impressive energy densities, making them highly attractive for renewable energy applications. LiFePO4 (LFP) is a highly promising active material for semi-solid and targeting flow batteries. One of the key advantages of LFP is its low raw materials cost, as it is composed of Earth-abundant elements such as iron and phosphorus. This makes it an attractive option for large-scale battery production. The recent developments in SSRFBs and RTFBs using LFP as catholyte hold great promise for the future of sustainable energy storage. The combination of LFP's low cost, safety, durability, and high energy density with the modularity and scalability of flow battery systems make for a compelling solution to the challenges of intermittent renewable energy sources. Ongoing research and development in this area will likely yield even further improvements in the performance and efficiency of LFP-based flow batteries, opening exciting new possibilities for sustainable energy storage.
This report covers a portion of an ongoing investigation of the durability of adhesives for the High Speed Civil Transport (HSCT) program. Candidate HSCT adhesives need to possess the high-temperature capability required for supersonic flight. This program was designed to initiate an understanding of the behavior of candidate HSCT materials when subjected to combined mechanical and thermal loads. Two adhesives (K3A and FM57) and two adherends (IM7/K3B polymeric composite and the titanium alloy Ti-6Al-4V) were used to fabricate thick adherend lap shear specimens. Due to processing problems, only the FM57/titanium bonds could be fabricated successfully. These are currently undergoing thermomechanical fatigue (TMF) testing. There is an acute need for an adhesive to secondarily bond polymeric composite adherends or, alternately, polymeric composites that remain stable at the processing temperatures of today's adhesives.
This paper introduces a novel approach to corrosion mitigation using electrodeposited, fractal Ni and NiYSZ coatings. Highly adherent, durable multiscale coatings with fractal dimensions above 1.80 were fabricated. Corrosion characteristics of coated plain and etched surfaces of In800H, SS310, SS316 and SS347, in comparison to Ha230, were studied in molten 60% NaNO 3 + 40% KNO 3 at 600 °C. The corrosion rate of coated Fe-based alloys reduced by up to 68% compared to uncoated alloys and was on par with or lower than the corrosion rate of Ha230. Furthermore, the corrosion-resistant coatings provide for use of low-cost alloys in high temperature corrosive environments.
The inaugural “Molten Salt Technologies – Powering the Future” Workshop marked a significant convergence of minds from diverse industries, each harnessing molten-salt technologies in innovative ways. Participants from sectors such as solar, geothermal, and advanced nuclear energy, as well as those involved in cutting-edge applications like thermal transport and rare-earth metals extraction, gathered to discuss their shared technical challenges and opportunities. Industry leaders in metal extraction and recycling, alongside experts in high-temperature sensor technology and advanced material manufacturing, also brought their unique perspectives to the table. This workshop served as a crucial platform for these varied industries to delve into the engineering intricacies that molten salt technologies entail. Common challenges such as understanding the thermophysical properties of salts, tackling corrosion mechanisms in harsh environments, and enhancing material resilience under extreme conditions were at the forefront of discussions. These technical sessions highlighted the critical need for cross-industry collaboration to address issues like salt life-cycle process engineering, impurity mitigation, and the development of durable, high-performance materials. By bringing together academia, industry, and representatives from national laboratories and the U.S. Department of Energy (DOE), the workshop facilitated a rich exchange of knowledge and experiences. This interaction not only fostered new partnerships but also strengthened the network among existing collaborators, setting the stage for joint solutions to the complex problems faced by all sectors using molten salt technologies. The event underscored the importance of collaborative efforts in overcoming common engineering challenges and advancing the application of molten-salt technologies across various industries. The workshop not only provided an essential forum for networking and idea exchange but also highlighted the collective drive towards innovative solutions that could benefit multiple fields.
The inaugural “Molten Salt Technologies – Powering the Future” Workshop marked a significant convergence of minds from diverse industries, each harnessing molten-salt technologies in innovative ways. Participants from sectors such as solar, geothermal, and advanced nuclear energy, as well as those involved in cutting-edge applications like thermal transport and rare-earth metals extraction, gathered to discuss their shared technical challenges and opportunities. Industry leaders in metal extraction and recycling, alongside experts in high-temperature sensor technology and advanced material manufacturing, also brought their unique perspectives to the table. This workshop served as a crucial platform for these varied industries to delve into the engineering intricacies that molten salt technologies entail. Common challenges such as understanding the thermophysical properties of salts, tackling corrosion mechanisms in harsh environments, and enhancing material resilience under extreme conditions were at the forefront of discussions. These technical sessions highlighted the critical need for cross-industry collaboration to address issues like salt life-cycle process engineering, impurity mitigation, and the development of durable, high-performance materials. By bringing together academia, industry, and representatives from national laboratories and the U.S. Department of Energy (DOE), the workshop facilitated a rich exchange of knowledge and experiences. This interaction not only fostered new partnerships but also strengthened the network among existing collaborators, setting the stage for joint solutions to the complex problems faced by all sectors using molten salt technologies. The event underscored the importance of collaborative efforts in overcoming common engineering challenges and advancing the application of molten-salt technologies across various industries. The workshop not only provided an essential forum for networking and idea exchange but also highlighted the collective drive towards innovative solutions that could benefit multiple fields.
As the power conversion efficiency (PCE) of perovskite solar cells (PSCs) have reached above 25.5%, the commercialization of PSCs appears to be imminent due to its lower fabrication cost, simpler manufacturing processes, and larger processing area over Si-based solar cells that dominate the current photovoltaic (PV) market. While many efforts have focused on tackling the stability and scalability issues with promising advances, the potential lead (Pb) toxicity issue has remained a concern of PSCs. Unlike the metallic Pb, the Pb 2+ in perovskite generally exhibit high solubility in water. However, Pb 2+ has so far appeared to be a necessary component in all high-efficiency PSCs. Handful methods have been explored to mitigate the potential Pb2+ leaking issue, which can be generally categorized as physical encapsulation and our pioneering chemical absorption method, which was extended by others later. Since device damage is inevitable in outdoor conditions, physical encapsulation alone is not sufficient to mitigate the long-term risk of leakage of soluble Pb 2+ to the environment under severe weather conditions. As a result, the chemical absorption approach has recently attracted significant attention as a more effective solution to confine the potential lead leakage. Hence, it is of great value to develop durable and highly efficient Pb-absorbing components that can be conveniently mounted onto the standard PSC stack as an add-on accessory in line with the encapsulation of PSCs instead of modifying the standard device fabrication and/or device configuration.
Thermal barrier coatings (TBC's) have been used in high thrust aircraft engines for many years, and have proved to be very effective in providing thermal protection and increasing engine efficiencies. TBC life requirements for aircraft engines are typically less than those required for industrial gas turbines. This paper describes current and future applications of TBC's in industrial gas turbine engines. Early testing and applications of TBC's is reviewed. Areas of concern from the engine designer's and materials engineer's perspective are identified and evaluated. This paper focuses on the key factors that are expected to influence utilization of TBC's in advanced industrial gas turbine engines. It is anticipated that reliable, durable and highly effective coating systems will be produced that will ultimately improve engine efficiency and performance.
High-entropy oxides (HEOs) have garnered significant interest as next-generation anode materials for lithium-ion batteries (LIBs) due to their high theoretical specific capacity and excellent structural stability. This study successfully synthesized spinel-structured (Al 0.2 Mn 0.2 Co 0.2 Ni 0.2 Zn 0.2 ) 3 O 4 HEO via a sol–gel method. The material was characterized by XRD, Raman and TEM, confirming a homogeneous single-phase spinel structure, with uniformly distributed elements-a hallmark of HEOs. Electrochemical tests demonstrated a stable cycling performance (438 mAh g −1 at 100 mA g −1 after 100 cycles and 350 mAh g −1 at 1 A g −1 after 1000 cycles) and rate capacity of 159 mAh g −1 at 2 A g −1 , The remarkable long-term cyclability and good rate capability highlight the potential of this HEO for practical applications in durable, high-power lithium-ion batteries. This work underscores the advantage of incorporating structurally stabilizing elements in HEOs for advanced energy storage.
The NASA Glenn Research Center (GRC) has been working to advance the technology necessary for a flywheel energy storage system for the past several years. Flywheels offer high efficiency, durability, and near-complete discharge capabilities not produced by typical chemical batteries. These characteristics show flywheels to be an attractive alternative to the more typical energy storage solutions. Flywheels also offer the possibility of combining what are now two separate systems in space applications into one: energy storage, which is currently provided by batteries, and attitude control, which is currently provided by control moment gyroscopes (CMGs) or reaction wheels. To date, NASA Glenn research effort has produced the control algorithms necessary to demonstrate flywheel operation up to a rated speed of 60,000 RPM and the combined operation of two flywheel machines to simultaneously provide energy storage and single axis attitude control. Two position-sensorless algorithms are used to control the motor/generator, one for low (0 to 1200 RPM) speeds and one for high speeds. The algorithm allows the transition from the low speed method to the high speed method, but the transition from the high to low speed method was not originally included. This leads to a limitation in the existing motor/generator control code that does not allow the flywheels to be commanded to zero speed (and back in the negative speed direction) after the initial startup. In a multi-flywheel system providing both energy storage and attitude control to a spacecraft, speed reversal may be necessary.
Tungsten and tungsten heavy alloys (WHAs), known for their remarkably high hardness, durability, and corrosion resistance, play a critical role in the thriving development of nuclear fusion reactors in recent years. However, the exploration in tungsten alloys for the nuclear-related applications has been limited by the difficulty of manufacturing and the complexity of experiments to reproduce the environment of nuclear reaction. Therefore, this project aims to utilize nanoscale simulation methods such as density functional theory (DFT) and molecular dynamics (MD) with the help of machine learning techniques to not only understand the mechanisms of tungsten alloys but also allow us to computationally predict their mechanical behaviors under extreme environments. One critical problem of the application of WHAs in nuclear reactors is the surface melting. In the current design of the SPARC reactor, the WHA, W97Ni2.1Fe0.9 or W97NiFe, is chosen to be the first wall components to confine the plasma where the particles are fiercely moving and colliding into each other to create nuclear fusion reaction. This process will generate extremely high heat flux onto these WHA tiles, leaving high surface temperature that could possibly melt the surface of the WHA tiles, As illustrated in Fig. 1(a). a laser experiment previously done illustrates that a rough surface damage would be made after the surface melting where the matrix area mainly composed of nickel and iron as shown in Fig. 1(b), will first melt and then leave vacancies between these tungsten grains. Unfortunately, these kinds of roughness on the first-wall components could be deadly to the plasma inside a Tokmak reactor because the heat that is supposed to dissipate at a designed ratio through the tiles may in turn be excessively absorbed and accumulated on any uneven area of the surface, which will eventually make the whole nuclear reaction fail. In this project, we will introduce a machine learning potential, Allegro, based on DFT calculation and then build a MD model for W-Ni-Fe alloys.
Photovoltaic (PV) module qualification standards, IEC 61215 and IEC 61730, were designed to apply to “general open-air climates” and IEC 61730 specifically indicated applicability of ambient air temperature of 40°C. Additionally, these standards provided allowances for so-called “open rack mounted PV modules” without a clear definition of “open-rack.” These implied restrictions and allowances meant that hotter climates or thermally restrictive installation methods may not be covered by these often customer-mandated certification standards. This is particularly salient for the significant growth regions of the Middle East and India that would be expected to operate at significantly higher temperatures. The applicability of these documents raised issues over the definition of “open rack” and the fact that the geographic location is just as important as the mounting configuration in assessing the impact of the micro-environment of a PV module. This work summarizes the scientific background for IEC Technical Specification 63126:2020 ED1, titled “Guidelines for qualifying PV modules components and materials for operation at high temperatures.” This standard was recently published by the IEC and is the first step in a systematic effort to rework these standards to address the question of temperature more directly. Instead of specifying a mounting condition, we specify different suites of tests suitable for a system (PV module, mounting style, and location) defined by the 98th percentile cell temperature. With a defined temperature regime to work from, this allowed us to use existing literature research combined with additional modeling work to determine, which tests would need to be modified. This resulted in suggested changes to material thermal indices, thermal cycling temperatures, hot spot testing, ultraviolet testing, and bypass diode testing among other tests and characteristics described in this study.
The long-term stability of protonic ceramic electrolysis cell (PCEC) materials under high-steam operating conditions remains a critical barrier to device commercialization. Here, we investigate the fundamental degradation mechanisms of dense BaCe 0.7 Zr 0.1 Y 0.1 Yb 0.1 O 3-δ (BCZYYb) electrolytes operated at 550 °C, 50% H 2 O in air. Over 1,000 h, the total electrolyte conductivity decreases by 11.1%, driven primarily by a >130% increase in grain-boundary resistivity. Post-mortem analyses reveal that damage is localized to near-surface grain boundaries extending ∼50 μm into the dense electrolyte pellet. This surface localization indicates that degradation is likely to be severe in thin, device-level electrolytes. Degradation is primarily attributed to chemo-mechanical grain-boundary weakening arising from hydration-induced chemical expansion, culminating in the formation of intergranular cracks oriented parallel to the pellet surface. These internal cracks subsequently react with steam and/or CO 2 , leading to the formation of nanoscale insulating phases, including Ba(OH) 2 , nanocrystalline BaCO 3 , and amorphous Ce/Zr/Y/Yb-containing oxides or hydroxycarbonates. After an initial degradation period of approximately 200 h, the overall conductivity stabilizes. Incorporating NiO sintering aids reduces grain-boundary density by an order of magnitude under identical sintering conditions. Although addition of NiO increases the initial resistivity by >160% at 550 °C, it substantially suppresses grain-boundary instability and mitigates chemical degradation. These findings underscore the urgent need for chemical and/or physical stabilization of BCZYYb electrolytes and offer design guidelines to enable durable, high-performance PCECs.
An electromotive force (emf) can be generated along a temperature gradient between the cold end and hot end of a thermoelectric material, termed the Seebeck effect. Based on the Seebeck effect, metallic alloys have been extensively employed to detect temperatures for centuries, named thermocouples. However, commercially available thermocouple alloys suffer from limitations, such as oxidation, chemical degradation, and poor long-term stability under high-temperature harsh environments. This DOE-funded project aimed to develop high-temperature, chemically tolerant thermocouples suitable for operation in extreme environments relevant to semiconducting thermoelectric materials. The research focused on boride-based semiconducting thermoelectric compounds as candidates for next-generation thermocouples with enhanced oxidation resistance, chemical stability, and thermal robustness under conditions representative of charcoal-fired electricity facilities. During the funded years, boride materials were synthesized using an arc-plasma technique under ambient air and argon atmospheres, enabling scalable and cost-effective production compared with conventional boride fabrication methods. The synthesized borides were processed into nanostructured powders, followed by consolidation into dense bulk materials using a spark plasma sintering (SPS) bottom-up approach. Comprehensive characterization was performed, including microstructural analysis, electrical transport measurements, and optical and thermal property evaluation. Both p-type and n-type boride electric legs were fabricated and integrated into boride-based thermocouples. The thermal and irradiation stabilities of the boride nanomaterials and bulk thermoelectric materials were systematically evaluated to assess suitability for long-term operation in harsh environments. Additionally, 12 students were broadly hands-on trained spanning the full research workflow, including word processing and technical editing (e.g., LATEX for manuscript and poster preparation), data collection and analysis (using Python and related libraries and hardware interfaces), sample preparation (including arc-plasma synthesis and spark plasma sintering), and advanced characterization techniques (such as X-ray diffraction, UV–vis spectroscopy, electron microscopy, differential thermal analysis (DTA), and Seebeck coefficient measurements, etc). Overall, this project demonstrated the feasibility of boride-based thermoelectric materials as durable high-temperature thermocouples, providing a promising pathway toward robust temperature sensing technologies aligned with DOE energy infrastructure and extreme-environment monitoring needs.