Search NASA⌕ Search

SEARCH · Search NASA

Results for “Ignition kinetics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

An Experimental and Numerical Investigation to Characterize the Low-Temperature Heat Release in Stoichiometric and Lean Combustion

This work reports on an experimental and modeling study on the low-temperature heat release (LTHR) characteristics for three RON 90 binary blends (n-heptane blended with isooctane, toluene and ethanol) in a Cooperative Fuel Research (CFR) engine at lean and stoichiometric conditions that are representative of homogeneous charge compression ignition (HCCI) and spark-ignition (SI) end-gas combustion conditions, respectively. An analysis of the end-gas temperature-pressure (T-P) trajectories was performed to identify the intake conditions leading to similar T-P trajectories between the two lambdas for each fuel blend. A heat release analysis was then conducted for the identified cases, where fuel-to-fuel differences in LTHR were identified and found to be sensitive to the operating condition. Simulations were conducted for these cases using a recently updated chemical kinetic model and a 0-D engine model, where good qualitative and reasonable quantitative agreements in LTHR were obtained. Sensitivity analysis was also performed directly on the rates of LTHR, to understand the controlling chemical reactions of LTHR, providing further insights into the fuel-to-fuel differences. The results demonstrate the significant promoting effect of n-heptane on LTHR rates, while inhibiting effects were seen for ethanol and toluene. Also highlighted was the importance of H atom abstraction reactions from the chemistry of each fuel component, which could lead to contradictory fuel behavior depending on the locations of the H site of the abstraction reaction due to the different ensuing pathways for the primary fuel radicals.

LTHR, RON 90 binary blends, sensitivity analysis↗
DOE OSTI2023

Fast correlation heating in moderately coupled electron–ion plasmas

If the electrons in a plasma are suddenly heated, the resulting change in Debye shielding causes the ion kinetic energy to quickly increase. For the first time, this correlation heating , which is much faster than collisional energy exchange, is rigorously derived for a moderately coupled, electron–ion plasma. The electron–ion mass ratio is taken to be the smallest parameter in the Bogoliubov–Born–Green–Kirkwood–Yvon hierarchy, smaller even than the reciprocal of the plasma parameter. This ordering differs from conventional kinetic theory by making the electron collision rates faster than the ion plasma frequency, which allows stronger coupling and makes the ion heating a function only of the total energy supplied to the electrons. The calculation uses known formulae for correlations in a two-temperature plasma, for which a new, elementary derivation is presented. Suprathermal ions may be created more rapidly by this mechanism than by ion–electron Coulomb collisions. This means that the use of a femtosecond laser pulse could potentially help to achieve ignition in certain fast ignition approaches to inertial confinement fusion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Unveiling the thermite-driven lithium fire ignition in solid-state batteries

Here, this study challenges the assumption of the non-flammability of lithium metal all-solid-state batteries (LiSSBs) and other lithium metal batteries without flammable electrolytes. Through thermodynamic calculations and ex situ experiments, we reveal for the first time the risk of thermite reactions between lithium metal and LiFePO 4 in both charged and discharged states. Reactivity is worsened by excess lithium metal in the cell, reaching final maximum adiabatic temperatures of 2,500°C in the charged state, which is hot enough to boil lithium. The thermite reaction triggers spontaneously at 500°C, with poor surface contact, while increasing surface contact through mixing initiates the reaction at room temperature in an inert environment. Despite its fast kinetics, this reaction is transport limited due to lithium passivation, leading to long burn times and reignition risks. Given the risk of lithium metal contacting the cathode during failure, understanding these reactions is crucial for ensuring the safe deployment of LiSSBs.

LiFePO4↗
DOE OSTI2021

Investigation of post-injection strategies for diesel engine Catalyst Heating Operation using a vapor-liquid-equilibrium-based spray model

Most multidimensional engine simulations spend much time solving for non-equilibrium spray dynamics (atomization, collision, vaporization). However, their accuracy is limited by significant grid dependency, and the need for extensive calibration. This is critical for modeling cold-start diesel fuel post injections, which occur at low temperatures and pressures, far from typical model validation ranges. At the same time, resolving micron-scale spray phenomena would render full Eulerian multiphase calculations prohibitive. In this study, an improved phase equilibrium based approach was implemented and assessed for simulating diesel catalyst heating operation strategies. A phase equilibrium solver based on the model by Yue and Reitz [1] was implemented: a fully multiphase CFD solver is employed with an engineering-size engine grid, and fuel injection is modeled using the standard Lagrangian parcels approach. Mass and energy from the liquid parcels are released to the Eulerian multiphase mixture according to an equilibrium-based liquid jet model. An improved phase equilibrium solver was developed to handle large real-gas mixtures such as those from accurate chemical kinetics mechanisms. The liquid-jet model was improved such that momentum transfer to the Eulerian solver better reproduces the physical spray jet structure. Validation of liquid/vapor penetration predictions showed that the model yields accurate results with very limited tuning and low sensitivity to the few calibration constants. In-cylinder simulations of diesel catalyst heating operation strategies showed that capturing spray structure is paramount when short, transient injection pulses and low temperatures are present. Furthermore, the EP model provides improved predictions of post-injection spray structure and ignitability, while conventional spray modeling does not capture the increase of liquid penetration during the expansion stroke. Finally, the only important EP model calibration constant, Cliq, does not affect momentum transfer, but it changes the local charge cooling distribution through the local energy transfer, which makes it candidate to additional research. The results confirm that non-equilibrium spray processes do not need to be resolved in engineering simulations of high-pressure diesel sprays.

42 ENGINEERING↗
DOE OSTI2021

Three dimensional low-mode areal-density non-uniformities in indirect-drive implosions at the National Ignition Facility

To achieve hotspot ignition, an inertial confinement fusion implosion must achieve high hotspot pressure that is inertially confined by a dense shell of DT fuel. This requires a symmetric implosion having high in-flight shell velocity and high areal density at stagnation. The size of the driver and scale of the capsule required can be minimized by maintaining a high efficiency of energy coupling from the imploding shell to the hotspot. Significant 3D low mode asymmetries, however, are commonly observed in indirect-drive implosions and reduce the coupling of shell kinetic energy to the hotspot. To better quantify the magnitudes and impacts of shell density asymmetries, we have developed new analysis techniques and analytic models [Hurricane et al., Phys. Plasmas 27(6), 062704 (2020)]. To build confidence in the underlying data, we have also developed an analytic neutron transport model to cross-compare two independent measurements of asymmetry, which shows excellent agreement across shots for mode-1 (ℓ = 1). This work also demonstrates that asymmetry can introduce potential sampling bias into down-scattered ratio measurements causing the solid-angle-average and uncertainty-weighted-average down-scattered ratios to differ significantly. Diagnosing asymmetries beyond mode-1 (ℓ > 1) presents significant challenges. Using new diagnostic instruments and analysis techniques, however, evidence of significant Legendre mode P2 (ℓ = 2, m = 0) and additional 3D asymmetries (ℓ > 1, m ≠ 0) are beginning to emerge from the high precision activation diagnostic data (real-time nuclear activation detectors) and down-scattered neutron imaging data.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A Rapid Compression Machine Study of 2-Phenylethanol Autoignition at Low-To-Intermediate Temperatures

To meet the increasing anti-knocking quality demand of boosted spark-ignition engines, fuel additives are considered an effective approach to tailor fuel properties for satisfying the performance requirements. Thus, screening/developing bio-derived fuel additives that are best-suited for advanced spark-ignition engines has become a significant task. 2-Phenylethanol (2-PE) is an attractive candidate that features high research octane number, high octane sensitivity, low vapor pressure, and high energy density. Recognizing that the low temperature autoignition chemistry of 2-PE is not well understood and the need for fundamental experimental data at engine-relevant conditions, rapid compression machine (RCM) experiments are therefore conducted herein to measure ignition delay times (IDTs) of 2-PE in air over a wide range of conditions to fill this fundamental void. These newly acquired IDT data at low-to-intermediated temperatures, equivalence ratios of 0.35–1.5, and compressed pressures of 10–40 bar are then used to validate the 2-PE model developed by Shankar et al. (2017). It is found that this literature model greatly overpredicts the current RCM data. The comparison of experimental and simulated results also provides insights into 2-PE autoignition behaviors at varying conditions. Further chemical kinetic analyses demonstrate that the absence of the O2-addition pathway of β-R. radical in the 2-PE model of Shankar et al. (2017) could account for the model discrepancies observed at low-to-intermediated temperatures.

Fang, Ruozhou (ORCID:0000000348315100)↗
DOE OSTI2025

First indirectly driven liquid-DT filled double shell implosions at the National Ignition Facility

Double shell implosions aim to explore material mixing under fusion conditions in a volume burn geometry using high-Z metal pushers. High-Z pushers are more compressible than low-Z pushers enabling high stagnation pressure which reduces the required implosion speed while maintaining a low pusher adiabat despite strong shock heating. Additionally, the use of a small fuel mass reduces the fuel internal energy required for ignition, thus achieving stable platforms with reasonable fusion output to conduct controlled experiments. These factors make volume burn in a double shell implosion highly promising. Recently, a series of liquid-DT filled, indirectly driven, double shell implosions were conducted at the National Ignition Facility with laser drives reaching up to 1.5 MJ. These experiments achieved a maximum DT neutron yield of 1.67 × 10 14 (yield—479 J), DT ion temperature of 2.6 keV, fuel areal density (ρR) of 0.15 g/cm 2 , and stagnation pressure of 79 Gbar. Over the course of these shots, the DT neutron yield has increased by an order of magnitude largely from improved mitigation of outer shell assembly joint driven instability growth using thicker gold plating at the assembly joint. Further performance improvements are expected by enhancing outer-to-inner shell kinetic energy transfer and refined mitigation of degradations from engineering features such as the outer shell joint, fill tube, and surface roughness.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Simulation and flow physics of a shocked and reshocked high-energy-density mixing layer

This work describes a computational investigation of multimode instability growth and multimaterial mixing induced by multiple shock waves in a high-energy-density (HED) environment, where pressures exceed 1 Mbar. The simulations are based on a series of experiments performed at the National Ignition Facility (NIF) and designed as an HED analogue of non-HED shock-tube studies of the Richtmyer–Meshkov instability and turbulent mixing. A three-dimensional computational modelling framework is presented. It treats many complications absent from canonical non-HED shock-tube flows, including distinct ion and free-electron internal energies, non-ideal equations of state, radiation transport and plasma-state mass diffusivities, viscosities and thermal conductivities. The simulations are tuned to the available NIF data, and traditional statistical quantities of turbulence are analysed. Integrated measures of turbulent kinetic energy and enstrophy both increase by over an order of magnitude due to reshock. Large contributions to enstrophy production during reshock are seen from both the baroclinic source and enstrophy–dilatation terms, highlighting the significance of fluid compressibility in the HED regime. Dimensional analysis reveals that Reynolds numbers and diffusive Péclet numbers in the HED flow are similar to those in a canonical non-HED analogue, but conductive Péclet numbers are much smaller in the HED flow due to efficient thermal conduction by free electrons. It is shown that the mechanism of electron thermal conduction significantly softens local spanwise gradients of both temperature and density, which causes a minor but non-negligible decrease in enstrophy production and small-scale mixing relative to a flow without this mechanism.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Time resolved X-ray diffraction using the FIDDLE diagnostic at NIF: Preliminary assessment of diffraction precision

The Flexible Imaging Diffraction Diagnostic for Laser Experiments (FIDDLE) is a new diagnostic at the National Ignition Facility (NIF) designed to observe in situ solid-solid phase changes at high pressures using time resolved X-ray diffraction. FIDDLE currently incorporates five Icarus Ultrafast X-ray Imager sensors that take 2 ns snapshots and can be tuned to collect X-rays for tens of ns. The platform utilizes the laser power at NIF for both the laser drive and the generation of 10 keV X-rays for ~10 ns using a Ge backlighter foil. We aim to use FIDDLE to observe diffraction at different times during compression to probe the kinetics of phase changes. Pb undergoes two solid-solid phase transitions during ramp compression: from FCC to HCP and HCP to BCC. Results will be reported on some of the first shots using the FIDDLE diagnostic at NIF on ramp compressed Pb to a peak pressure of ~110 GPa and a single undriven CeO2 calibration shot. A discussion of the uncertainties in the observed diffraction is included.

Vennari, C. E.↗
DOE OSTI2026

Effects of Gasoline Composition and Operating Parameters on the Response of End-Gas Autoignition to Nitric Oxide in a Lean-Burn DI-SI Engine

Lean operation of spark-ignition engines can lead to engine thermal efficiency gains and lower NOx emissions due to reduced combustion temperatures. Yet, lean operation could still face challenges in end-gas autoignition and knock generation due to higher intake pressures and trapped NO in the residual gas. Here, this study evaluates the impact of NO on end-gas autoignition for two gasoline fuels with similar octane rating but different composition: high cycloalkane fuel (HCA) and high olefin fuel (HO). Experiments were performed at stoichiometric and lean (λ = 2) conditions and at two engine speeds of 1400 rpm and 2000 rpm. Accompanying chemical kinetics simulations in CHEMKIN revealed that the mechanisms controlling the effect of NO on autoignition are similar λ = 2 and λ = 1, with NO + HO 2 = NO 2 + OH being the main pathway for enhancing reactivity by promoting low-temperature heat release (LTHR). The compositionally different fuels reacted differently to NO seeding and engine speed, and differences were augmented at λ = 2 compared to λ = 1 as the end-gas autoignition shifted to the low temperature regime. HO, which has inherent low temperature chemistry, was strongly impacted by engine speed at low NO seeding levels, with no noticeable peak of LTHR detected at 2000 rpm. On the other hand, LTHR of HCA was marginally affected by shortened residence time at higher engine speed as NO + HO 2 reaction was not greatly affected by shorter time scales, since HO 2 production was sustained even at 2000 rpm to support OH generation from NO + HO 2 . Contrary to HO, HCA exhibited greater sensitivity to NO seeding, as the increased OH production at higher NO concentrations offset the OH-quenching effect of cyclopentane, which accounts for 28.6% of HCA’s composition. Consequently, a sensitivity analysis revealed that fuels with weak inherent low-temperature chemistry, like HCA, are likely to be more sensitive to variations in NO concentration and charge temperature, whereas fuels with strong low temperature chemistry are more sensitive to variations in end-gas λ and intake pressure.

Energy↗
DOE OSTI2021

Influence of NOx Chemistry on the Prediction of Natural Gas End-Gas Autoignition

Research on the influence of NOx (NO/NO2) chemistry on HC oxidation has shown that NOx plays an important role in the promotion/inhibition of HC autoignition [1-6]. Current data for n-heptane, iso-octane, ethanol, and toluene [3, 4] have shown that NO chemistry inhibits autoignition at low temperatures and concentrations. However, at medium and high temperatures and low concentrations, autoignition is promoted, decreasing the Negative Temperature Coefficient (NTC) effect. This autoignition promotion, however, becomes weaker as NO concentrations are increased. Additionally, fundamental kinetics studies have suggested that NOx chemistry also promotes the autoignition of smaller HC, such as CH4 [7-10], C2H6 [11-14], and C3H8 [15]. Additionally to the chemical kinetics studies, a growing body of evidence supports the importance of NOx chemistry on SI engine simulations [16, 17]. Foong et al. [18] suggested that the addition of NO in their models significantly improved the agreement between simulations and experiments where the onset of knock was advanced due to the presence of NO, and Morganti et al. [19] showed that NO addition in the residual-gas was necessary for their models to obtain good agreement with experimental data. Lastly, Mohr et al. [20, 21] investigated the effect of Natural Gas (NG) reactivity and EGR substitution rate and composition on homogeneous ignition delay, flame speeds, and EGAI for stoichiometric NG/oxidizer/EGR blends. They observed that the addition of EGR composed of only inert species (CO2 and Ar) suppressed homogeneous autoignition in all NG fuels tested under all conditions. However, for all NG fuels tested, increasing EGR rates with reactive species (Ar, CO2, CO, and NO) promoted homogeneous autoignition under all conditions, thus reproducing the same trends for various NG fuel compositions that were observed in other studies and fuels. For this reason, a study is being conducted to analyze the effects of NOx chemistry on the prediction of NG/air/EGR homogeneous autoignition. This study has been divided into two tasks. First, the addition of NOx chemistry to the ARIES82 mechanism [20] is being validated using homogeneous ignition delay data collected by Mohr [20, 21]. Second, once the new modified mechanism with NOx reactions has been validated, it will be employed on engine multi-dimensional modeling presented in [22, 23] to analyze the influence of NOx chemistry on NG EGAI. Results thus far have shown that homogeneous ignition delay calculations are sensitive to NOx chemistry, where the modified mechanisms captured well all trends and closely matched the homogeneous ignition delays observed by Mohr et al. Also, the results in this work suggest that NOx chemistry is necessary to correctly capture the trends in NG homogeneous autoignition when EGR with reactive species is used since the opposite behavior is observed when only inert species are considered for the EGR composition.

03 NATURAL GAS↗
DOE OSTI2023

n-Propylbenzene Droplet Combustion: Experiments and Numerical Modeling

n-Propylbenzene (PB, C9H12, 432K boiling point) is important as a constituent in surrogates for some transportation fuels but little is understood about its droplet burning characteristics. We present an experimental and numerical study of a fuel droplet burning under conditions where the sole means of gas transport is fuel evaporation at the droplet surface thereby creating a one-dimensional gas transport that is amenable to detailed numerical modeling. The one-dimensional gas transport that results is amenable to detailed numerical modeling. Initial droplet diameters (Do) ranged from 0.3 mm to about 5 mm to better understand the mechanisms that control burning over such a wide range of Do. For Do < 1 mm droplets were burned while anchored to 14 m SiC fibers within a sealed container in free-fall during which time the droplets were ignited by spark discharge and the burning process recorded by video cameras. Larger and free-floating droplets were studied in the spaced-based platform of the orbiting International Space Station for Do > 1.0 mm which provided unlimited times for experimental observation. Measurements of droplet, flame and soot shell diameters were made and are discussed in the presentation. The experimental results showed formation of optically thick soot clouds developing during burning that required a robust image analysis algorithm to enable measurement of droplet diameter. The measured droplet diameters were well predicted by a numerical model that included soot formation, a PB kinetic mechanism comprising 576 species and 27369 reactions, unsteady gas and liquid transport, variable properties and radiative transport. Flame diameters showed more variability compared to the simulations, depending on how the flame was defined (peak gas temperature and OH concentration). Droplets burned slower as Do was increased and the PB sooting propensity increased with Do. Flame extinction was observed for Do > 3.3 mm indicating a strong effect of radiation as Do was increased compared to the smaller droplet diameters examined where extinction was not experimentally observed. For the largest droplets examined the possibility that the observed extinction is indicative of a transition to cool flame burning is still under investigation.

Guo, Songtao↗
DOE OSTI2021

Numerical Analysis of Fuel Effects on Advanced Compression Ignition Using a Cooperative Fuel Research Engine Computational Fluid Dynamics Model

Growing environmental concerns and demand for a better fuel economy are driving forces that motivate the research for more advanced engines. Multi-mode combustion strategies have gained attention for their potential to provide high thermal efficiency and low emissions for light-duty applications. These strategies target optimizing the engine performance by correlating different combustion modes to load operating conditions. The extension from boosted spark ignition (SI) mode at high loads to advanced compression ignition (ACI) mode at low loads can be achieved by increasing the compression ratio and utilizing intake air heating. Further, in order to enable an accurate control of intake charge condition for ACI mode and rapid mode-switches, it is essential to gain fundamental insights into the autoignition process. Within the scope of ACI, homogeneous charge compression ignition (HCCI) mode is of significant interest. It is known for its potential benefits, operation at low fuel consumption, low NOx, and particulate matter (PM) emissions. In the present work, a virtual Cooperative Fuel Research (CFR) engine model is used to analyze fuel effects on ACI combustion. In particular, the effect of fuel octane sensitivity (S) (at constant Research Octane Number (RON)) on autoignition propensity is assessed under beyond-RON (BRON) and beyond-MON (BMON) ACI conditions. The three-dimensional CFR engine computational fluid dynamics (CFD) model employs a finite-rate chemistry approach with a multi-zone binning strategy to capture autoignition. Two binary blends with Research Octane Number (RON) of 90 are chosen for this study: primary reference fuel (PRF) with S = 0 and toluene–heptane (TH) blend with S = 10.8, representing paraffinic and aromatic gasoline surrogates. Reduced mechanisms for these blends are generated from a detailed gasoline surrogate kinetic mechanism. Simulation results with the reduced mechanisms are validated against experimental data from an in-house CFR engine, with respect to in-cylinder pressure, heat release rate, and combustion phasing. Thereafter, the sensitivity of combustion behavior to ACI operating condition (BRON versus BMON), air-fuel ratio (λ = 2 and 3), and engine speed (600 and 900 rpm) is analyzed for both fuels. It is shown that the sensitivity of a fuel’s autoignition characteristics to λ and engine speed significantly differs at BRON and BMON conditions. Moreover, this sensitivity is found to vary among fuels, despite the same RON. It is also observed that the presence of low-temperature heat release (LTHR) under BRON condition leads to more sequential autoignition and longer combustion duration than BMON condition. Finally, the study indicates that the octane index (OI) fails to capture the trend in the variation of autoignition propensity with S under the BMON condition.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2026

Examining experimental nitrogen-based emissions trends from ammonia/diesel and ammonia/hydrogen/diesel combustion

Ammonia has garnered interest as an alternative fuel for power sectors with heavy payload and distance requirements, such as shipping. In this study, ammonia was used in a dual-fuel compression-ignition combustion strategy to overcome some of its technical barriers, using a diesel pilot to ignite a premixed mixture of ammonia and air. Mixtures of premixed ammonia and hydrogen were also explored to evaluate whether the inclusion of hydrogen improves nitrogen-based emissions from the combustion process. A single-cylinder version of a Cummins ISB 6.7 L engine platform was used to experimentally study these effects at various global air/fuel ratios and hydrogen energy fractions. Hydrogen inclusion produced pronounced NOx and N2O emissions, while inclusion of trapped residuals increased N2O but reduced NOx. The two most recent and relevant mechanisms available in the literature—those from Xu and Zhang-Ren-Kokjohn—were used in a chemical kinetics analysis to examine the observed differences in the NOx trends from two dual-fuel ammonia/diesel datasets: (1) in which a portion of the premixed ammonia was substituted with hydrogen and (2) in which the effect of hot trapped residuals was evaluated with only ammonia/air premixed mixtures. The analysis with both mechanisms showed agreement with experimental trends; however, contributions from thermal vs. fuel-borne NOx pathways showed disagreement. A reaction pathway analysis showed that the HNO to NO pathway was the key to NO formation in the mixture.

Tyrewala, Daanish [ORNL] (ORCID:0000000208599324)↗
DOE OSTI2022

Flame acceleration and transition to detonation in a pre-/main-chamber combustion system

Numerical simulations are performed to study the mechanism of deflagration to detonation transition (DDT) in a pre-/main-chamber combustion system with a stoichiometric ethylene–oxygen mixture. A Godunov algorithm, fifth-order in space, and third-order in time, is used to solve the fully compressible Navier–Stokes equations on a dynamically adapting mesh. A single-step, calibrated chemical diffusive model described by Arrhenius kinetics is used for energy release and conservation between the fuel and the product. The two-dimensional simulation shows that a laminar flame grows in the pre-chamber and then develops into a jet flame as it passes through the orifice. A strong shock forms immediately ahead of the flame, reflecting off the walls and interacting with the flame front. The shock–flame interactions are crucial for the development of flame instabilities, which trigger the subsequent flame development. The DDT arises due to a shock-focusing mechanism, where multiple shocks collide at the flame front. A chemical explosive mode analysis (CEMA) criterion is developed to study the DDT ignition mode. Preliminary one-dimensional computations for a laminar propagating flame, a fast flame deflagration, and a Chapman–Jouguet detonation are conducted to demonstrate the validity of CEMA on the chemical-diffusive model, as well as to determine the proper conditioning value for CEMA diagnostic. The two-dimensional analysis with CEMA indicates that the DDT initiated by the shock-focusing mechanism can form a strong thermal expansion region at the flame front that features large positive eigenvalues for the chemical explosive mode and dominance of the local autoignition mode. Thus, the CEMA criterion proposed in this study provides a robust diagnostic for identifying autoignition-supported DDT, of which the emergence of excessive local autoignition mode is found to be a precursor. The effect of grid size, initial temperature, and orifice size are then evaluated, and results show that although the close-chamber DDT is highly stochastic, the detonation initiation mechanism remains robust.

42 ENGINEERING↗
DOE OSTI2023

SAF Combustion & Soot Processes [Slides]

The atomization, mixing, combustion and emissions characteristics of aviation fuels were measured using a novel approach based on a non-continuous injection scheme called the single-hole atomizer (SHA). High-speed microscopy revealed differences between fuels in terms of evaporation and mixing regimes over conditions relevant to modern and next generation aero-engine combustors. Measurements of liquid and vapor penetration, mixing fields, combustion and emissions metrics (ignition delay, lift-off length, PAH formation, soot mass) highlighted the effects of fuels and combustor conditions. The experimental results are being leveraged to adjust and validate chemical and CFD models. Detailed analysis of sampled soot showed subtle differences in soot morphology between fuels. The results revealed the presence of contaminants potentially affecting surface chemistry and the nucleation propensity of water droplets on particles. Chemical mechanisms for NJFCP A-2, C-1 and C-4 showed good performance over a large parameter space. Spray breakup at relight conditions is vastly different from the atomization observed at high pressure. CFD simulations of the SHA target conditions confirmed the good behavior of the C-1 kinetic mechanism. The simulations support the strong relationship between low and high temperature reactions. New altitude chamber facility to enable detailed characterization of the heterogeneous nucleation process of water on aerosol particles.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

What next: Further implosion space exploration on the path to NIF extended yield capability

We present quantitative motivations and assessments of various proposed and ongoing directions to further improving yields and target gain of igniting indirect-drive implosions at the National Ignition Facility (NIF). These include increasing compression and confinement time, improving hohlraum and ablator efficiency, and further increasing peak power and laser energy. 1D hydroscaled simulations, augmented by analytic 1D theory, have been used to project yield improvements for each of these implosion optimization tracks, normalized to the best current performing 4 MJ shot. At current NIF capabilities of 2.2 MJ, 450 TW, we project several paths could reach 15 MJ yield levels. We also expect several key implosion physics questions will be addressed in attempting to reach this yield level. These include demonstrating to what extent lower adiabat designs leading to higher compression will increase gain and efficiency, and whether we can reduce residual kinetic energy and ablator-fuel mix that is probably limiting the current burn-up fraction. For an envisaged NIF upgrade to EL = 3 MJ at fixed 450 TW peak power, scaling capsule size and fuel thicknesses faster than pure hydroscaling should allow for yields that could reach up to 60–80 MJ, depending on the efficiency gains realized in increasing deuterium-tritium fuel thickness, reducing hohlraum losses, and switching to lower Z ablators. The laser-plasma instability and beam transmission scaling in these larger hohlraums is shown to be favorable if the spot size is increased with hohlraum scale.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

1D modeling of plasma streamers at ammonia-air flame conditions

Abstract Self-consistent 1D modeling of streamers in ammonia-oxygen-nitrogen-water mixtures has been performed in this work. A fluid model that includes species transport, electrostatic potential, and detailed chemistry was developed and verified. This model is then used to simulate the avalanche, streamer formation and propagation phases, driven by a nanosecond voltage pulse, at different thermochemical conditions derived from a 1D laminar premixed ammonia-air flame. The applicability of the Meek’s criterion in predicting the streamer inception location was successfully confirmed. Streamer formation and propagation duration were found to vary significantly with different thermochemical conditions, due to the difference in ionization rates. The thermochemical state also affected the breakdown characteristics which was tested by maintaining the background reduced electric field constant. Detailed kinetic analyses revealed the importance of O ( 1 D ) in the production of key radicals, such as O, OH, and NH 2 . Furthermore, the contributions of the dissociative electronic excitation of NH 3 towards the production of H and NH 2 radicals have also been reported. Spatial and temporal evolution of the electron energy loss fractions for various inelastic collision processes at different thermochemical states uncovered the input plasma energy spent of fuel dissociation and the large variability in the dominant processes during the avalanche and streamer propagation phases. The methodology and analyses reported in this work are key towards developing effective strategies for controlled nanosecond-pulsed non-equilibrium plasma sources used for ammonia ignition and flame stabilization.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗