SEARCH · Search NASA

Results for “Level Control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

All sources NASA NTRS DOE OSTI

NASA NTRS1973

Solid state power controllers

The rationale, analysis, design, breadboarding and testing of the incremental functional requirements are reported that led to the development of prototype 1 and 5 Amp dc and 1 Amp ac solid state power controllers (SSPC's). The SSPC's are to be considered for use as a replacement of electro-mechanical relays and circuit breakers in future spacecraft and aircraft. They satisfy the combined function of both the relay and circuit breaker and can be remotely controlled by small signals, typically 10 mA, 5 to 28 Vdc. They have the advantage over conventional relay/circuit breaker systems in that they can be located near utilization equipment and the primary ac or dc bus. The low level control, trip indication and status signals can be circuited by small guage wire for control, computer interface, logic, electrical multiplexing, unboard testing, and power management and distribution purposes. This results in increased system versatility at appreciable weight saving and increased reliability.

Gibbs, R. S.↗

NASA NTRS1994

Experiment K-7-29: Connective Tissue Studies: Changes in Muscle Serine Proteases, Serpins and Matrix Molecules - Part 2

In zero or micro-gravity, type 1 muscle fibers atrophy and lose predominance, especially in slow-twitch muscles. No increase in mononuclear cells has been observed, just as in simple denervation, where both types 1 and 2 fibers atrophy, again without infiltration of cells, but with clear satellite cell proliferation. However, extracellular matrix (ECM) degradation takes place after denervation and if re-innervation is encouraged, functional recovery to near control levels may be achieved. No information is available concerning the ECM milieu, the activation of serine proteases, their efficacy in degrading ECM components and the production of locally-derived natural protease inhibitors (serpins) in effecting surface proteolytic control. In addition, no studies are available concerning the activation of these enzymes in micro- or zero gravity or their response to muscle injury on the ground and what alterations, if any, occur in space. These studies were the basis for the experiments in Cosmos 2044.

Festoff, B. W.↗

NASA NTRS1995

Exercise Training During Bed Rest Attenuates Deconditioning

A 30-day 6 deg. head-down bed rest study was conducted to evaluate high-intensity, short-duration, alternating isotonic cycle ergometer exercise (ITE) training and high-intensity intermittent isokinetic exercise (IKE) training regiments designed to maintain peak VO2 and muscle mass, strength, and endurance at ambulatory control levels throughout prolonged bed rest. Other elements of the deconditioning (acclimation) syndrome, such as proprioception, psychological performance, hypovolemia, water balance, body composition, and orthostatic tolerance, were also measured. Compared with response during bed rest of the no exercise (NOE) control group: the ITE training regimen (a) maintained work capacity (peak VO2), (b) maintained plasma and red cell volume, (c) induced positive body water balance, (d) decreased quality of sleep and mental concentration, and (e) had no effect on the decrease in orthostatic tolerance; the IKE training regimen (a) attenuated the decrease in peak VO2 by 50%, (b) attenuated loss of red cell volume by 40%, but had no effect on loss of plasma volume, (c) induced positive body water balance, (d) had no adverse effect on quality of sleep or concentration, and (e) had no effect on the decrease in orthostatic tolerance. These findings suggest that various elements of the deconditioning syndrome can be manipulated by duration and intensity of ITE or IKE training regiments, and that several different training protocols will be required to maintain or restore physiological and psychological performance of individuals confined to prolonged bed rest.

Greenleaf, J. E.↗

NASA NTRS1974

Solid state power controllers

Solid state power controllers (SSPC's) are to be considered for use as replacements of electromechanical relays and circuit breakers in future spacecraft and aircraft. They satisfy the combined function of both the relay and circuit breaker and can be remotely controlled by small signals, typically 10 mA, 5 to 28 v(dc). They have the advantage over conventional relay/circuit breaker systems in that they can be located near the utilization equipment and the primary ac or dc bus. The low level control, trip indication and status signals can be circuited by small gauge wire for control, computer interface, logic, electrical multiplexing, onboard testing, power management, and distribution purposes. This results in increased system versatility at appreciable weight saving and increased reliability. Conventional systems require the heavy gage load wiring and the control wiring to be routed from the bus to the load to other remote relay contacts, switches, sensors, etc. and to the circuit breaker located in the flight engineer's compartment for purposes of manual reset.

Gibbs, R. S.↗

DOE OSTI2024

Adaptive Laboratory Evolution for Enhanced Performance of Cupriavidus Necator on Formic Acid

The threat of global warming, driven by rising carbon emissions, highlights the need to decarbonize our economy. This requires innovative solutions for managing carbon waste and its effective utilization. One promising method for CO2 capture and sequestration is the electrochemical reduction of CO2 to formic acid, a soluble C1 molecule that can be used to store carbon and energy, and as a feedstock for biological conversion. Cupriavidus necator H16, a soil bacterium capable of consuming and growing on formic acid as its sole carbon and energy source, is well positioned to upgrade CO2-derived formic acid into platform chemicals and fuel precursors. To improve the performance of C. necator on formic acid, adaptive laboratory evolution (ALE), a proven tool for improving microbial fitness, has been conducted using continuous pH-stat bioreactors. The system works on the basis that consumption of formic acid raises the pH and triggers the addition of more formic acid to maintain the pH (in this case 6.7), such that formic acid is provided at the same rate as it is consumed. This system has been coupled with level control to achieve continuous fermentation where cells acquiring mutations that improve growth on formic acid become more abundant in the population, from which they can be isolated and characterized. During developmental experiments it was discovered that formic acid accumulated to inhibitory levels. It was determined that the nitrogen source, ammonium hydroxide, must be tailored to the carbon consumption to avoid formic acid accumulation. The ALE ran in three lineages for approximately 3000 hours and more than 500 generations. Evolved isolates obtained from each lineage demonstrated an increase in growth rate in conjunction with improve formate utilization compared to the parental strain when evaluated in pH-stat bioreactors. The isolates with improved performance were then subjected to whole genome sequencing to identify potentially causative mutations. Mutations in several key genes across different lineages have been found and will be evaluated individually and in combination to identify those that improve growth on formic acid. Incorporating these mutations into production strains has the potential to greatly improve formic acid conversion and further industrial decarbonization.

adaptive laboratory evolution↗

DOE OSTI2025

Design Principles in Engineering of Multigrain Nanocatalysts via Multiscale Electronic Structure Characterization

Engineering grain boundary (GB) strain provides a promising pathway to tune the catalytic properties of nanocrystals. However, structural heterogeneity from random grain orientation and geometry has limited clear structure–property correlations. Here, we utilize a multigrain Co3O4/Mn3O4 core/shell nanocrystal platform as a model system to systematically investigate how geometric misfit strain at GBs serves as catalytically active sites for the oxygen reduction reaction. Through precise subnanometer-level control over grain morphology and by integrating multiscale electronic structure characterization, we identify the electronic structural signature of GB defects and establish a direct correlation between localized strain fields and modified electronic states. Strain modulation at GBs alters the eg orbital energy levels, with elongation along the z-axis combined with shear strain stabilizing the eg states, in contrast to the destabilization observed under pure shear strain. This stabilization mechanism enhances the electrocatalytic activity and selectivity of strained GBs compared with strain-relaxed grain surfaces. Furthermore, we reveal that GBs exhibit a radial strain gradient, producing a spatial energy shift that further modulates local electronic structures, as resolved through the classification of electron energy loss spectroscopy data. Together, these findings demonstrate that geometric misfit strain enables precise tuning of grain geometry and the resulting electronic structures, offering a robust strategy for engineering next-generation nanocatalysts.

Cho, Min Gee↗

DOE OSTI2023

Strengthening Cybersecurity for Industrial Control Systems: Innovations in Protecting PLC-Based Infrastructure

In this paper, we propose two new approaches aimed at enhancing the security of industrial control systems (ICS) that utilize programmable logic controllers (PLCs) for the control of critical processes. The first approach involves the addition of a unique digital watermark to the PWM control that adjusts the motor speed to control the critical process. This enables efficient detection and identification of any unauthorized modifications to the sensor signals responsible for controlling the plant. The second approach focuses on monitoring the input current (i.e power) drawn by the PLC during the execution of critical process control tasks. Malicious intrusions to change the PLC parameters and/or unauthorized firmware updates can be rapidly detected. Both approaches demonstrate a substantial improvement in the security of ICS, effectively safeguarding against potential cyber-attacks. Experimental results from a laboratory scale water tank level controlled via PLC showcases rapid intrusion detection capabilities.

Huang, Peng-Hao↗

NASA NTRS1975

Hematologic changes in mice during and after exposure to severe hypobaric hypoxia

Exposing mice to an atmospheric pressure of 300 mm Hg for 16 d caused a variety of hematologic effects. Hematocrit increased rapidly in the first 8 d of exposure and slowly in the second 8 d. Reticulocyte counts rose above normal, peaked on day 8, and then fell rapidly toward the control level. Macrocytic erythrocytes, formed during exposure, remained macrocytic after the termination of exposure and after the loss of their reticulum. The posthypoxic mice proved sensitive for erythropoietin bioassay. Mice injected with normal dog serum showed a significantly higher incorporation of Fe-59 than control mice injected with physiologic saline. A reduction of the duration of exposure to 10 d resulted in only a slight decrease in the sensitivity of the mouse bioassay system. However, a 16-d exposure at a pressure of 360 mm Hg resulted in considerably less sensitive bioassay animals.

Huff, J. E.↗

NASA NTRS1997

Intensive Exercise Training During Bed Rest Attenuates Deconditioning

Intensive exercise training during bed rest attenuates deconditioning. Med. Sci. Sports Exerc., Vol. 29, No. 2, pp. 207-215, 1997. A 30-d 6 deg head-down bed rest project was conducted to evaluate variable high-intensity, short-duration, isotonic cycle ergometer exercise (ITE) training and high-intensity intermittent resistive isokinetic exercise (IKE) training regimens designed to maintain peak VO2 and muscle mass, strength, and endurance at ambulatory control levels throughout prolonged bed rest. Other elements of the deconditioning (adaptive) syndrome, such as proprioception, psychological performance, hypovolemia, water balance, body composition, and orthostatic tolerance, were also measured. Major findings are summarized in this paper. Compared with response during bed rest of the no exercise (NOE) control group: the ITE training regimen (a) maintained work capacity (peak VO2), (b) maintained plasma and red cell volumes, (c) induced positive body water balance, (d) decreased quality of sleep and mental concentration, and (e) had no effect on the decrease in orthostatic tolerance; the IKE training regimen (f) attenuated the decrease in peak VO2 by 50%, (g) attenuated loss of red cell volume by 40% but had no effect on loss of plasma volume, (b) induced positive body water balance, (i) had no adverse effect on quality of sleep or concentration, and 0) had no effect on the decrease in orthostatic tolerance. These findings suggest that various elements of the deconditioning syndrome can be manipulated by duration and intensity of ITE or IKE training regimens and that several different training protocols will be required to maintain or restore physiological and psychological performance of individuals confined to prolonged bed rest.

Greenleaf, John E.↗

NASA NTRS1992

Adaptation of Cancellous Bone to Aging and Immobilization in Growing Rats

Two-and-a half month-old female rats were subjected to right hindlimb immobilization or served as controls for 0, 1, 2, 8, 14, and 20 weeks. The right hindlimb was immobilized by bandaging it against the abdomen, thus unloading it. Cancellous bone histomorphometry was performed on microradiographs and double-fluorescent labeled 20 micron sections of the distal femoral metaphyses. Primary spongiosa bone loss occurred rapidly by 2 weeks, and secondary spongiosa bone loss occurred rapidly by 8 weeks of immobilization, and then equilibrated at 60% less bone mass than age-related controls. The negative bone balance induced by immobilization was caused by transient increase in bone resorption, decrease in bone formation, and longitudinal bone growth. The dynamic data of secondary spongiosa cancellous bone showed that percent eroded perimeter was transiently elevated by 55% to 82% between 1 and 8 weeks, percent labeled perimeter was transiently depressed by 32% to 50% between 1 and 14 weeks, mineral apposition rate was depressed by 23% and 19% at 1 and 2 weeks, and bone formation rate-bone area referent was transiently depressed by 35% and 59%c at 1 and 2 weeks. All the above parameters were at age-related control levels by 20 weeks of immobilization. However, bone formation rate-tissue area referent was depressed (-65%) throughout the study. Immobilization depressed completely longitudinal bone growth by 2 weeks and remained so. Only 0.65 mm of new metaphysis was generated in the immobilized versus 2.1 mm in controls during the study period. The immobilization induced an early cancellous bone loss which equilibrated at a new steady state with less bone and a normal (age-related control) bone turnover rate. When these findings were compared to an earlier study of 9 month-old virgin females subjected to right hindlimb immobilization up to 26 weeks, we found the adaptive responses of the cancellous bone were identical except that they occurred earlier and equilibrated sooner in younger rats.

Chen, Meng Meng↗

NASA NTRS2017

Generating Real-Time Robotics Control Software from SysML

In this paper, we outline an approach for autogenerating real-time robotics control code from hierarchical state machines and hardware configurations encoded in Systems Modeling Language (SysML). We propose a software architecture that provides an abstract SysML layer with access to device state information and a set of primitive device commands, such as move actuator and release brake, allowing a user to build up a complete functional state machine directly in SysML. The SysML diagram is then exported to a standard SCXML file format and subsequently used to auto-generate hardware control code. Once this architecture is in place, the only explicit code elements that need to be written are the primitive device commands, which can be easily unit tested and reused across different systems. The motivation for this work was the need for a test bed that enables the rapid prototyping of mechanisms and control algorithms for a spacecraft that could ultimately be used for preparing Martian rock samples for their return to Earth. To this end, our software system was also designed to allow for the run-time specification of the hardware layout in SysML, with the hardware-level control functions kept agnostic to the specific parameters or communication bus of any particular device. Further, we outline a system for specifying both the state machine and hardware configuration in the MagicDraw IDE in such a way that the system can be simulated before any code is generated. The resultant software system is easy to debug, understand, and allows users to choose how much information is encoded as a visual or text-based representation.

Godart, Peter↗

NASA NTRS1995

Robust integrated neurocontroller for complex dynamic systems

The goal of this research effort is to develop an integrated control software environment for the purpose of creating an intelligent neurocontrol system. The system will be capable of estimating states, identifying parameters, diagnosing conditions, planning control strategies, and producing intelligent control actions. The distinct features of such control system are adaptability and on-line learning capability. The proposed system will be flexible to allow structure adaptability to account for changes in the dynamic system such as sensory failures and/or component degradations. The developed system should learn system uncertainties and changes, as they occur, while maintaining minimal control level on the dynamic system. The research activities set to achieve the research objective are summarized by the following general items: (1) Development of a system identifier or diagnostic system; (2) Development of a robust neurocontroller system, and; (3) Integration of above systems to create a robust Integration Control system (RIC-system). Two contrary approaches are investigated in this research: classical (traditional) design approach, and the simultaneous design approach. However, in both approaches neural network is the base for the development of different functions of the system. The two resulting designs will be tested and simulation results will be compared for better possible implementation.

Zein-Sabbato, S.↗

NASA NTRS1996

Robust Integrated Neurocontroller for Complex Dynamic Systems

The goal of this research effort is to develop an integrated control software environment for the purpose of creating an intelligent neurocontrol system. The system will be capable of estimating states, identifying parameters, diagnosing conditions, planning control strategies, and producing intelligent control actions. The distinct features of such control system are: adaptability and on-line learning capability. The proposed system will be flexible to allow structure adaptability to account for changes in the dynamic system such as: sensory failures and/or component degradations. The developed system should learn system uncertainties and changes, as they occur, while maintaining minimal control level on the dynamic system. The research activities set to achieve the research objective are summarized by the following general items: (1) Development of a system identifier or diagnostic system, (2) Development of a robust neurocontroller system, and 3. Integration of above systems to create a Robust Integrated Control system (RIC-system). Two contrary approaches are investigated in this research: classical (traditional) design approach, and the simultaneous design approach. However, in both approaches neural network is the base for the development of different functions of the system. The two resulting designs will be tested and simulation results will be compared for better possible implementation.

Zein-Sabatto, S.↗

NASA NTRS1992

Adaptation of Cancellous Bone to Aging and Immobilization in Growing Rats

Two-and-half-month-old female rats were subjected to right hindlimb immobilization or served as controls for 0, 1, 2, 8, 14, and 20 weeks. The right hindlimb was immobilized by bandaging it against the abdomen, thus unloading it. Cancellous bone histomorphometry was performed on microradiographs and double-fluorescent labeled 20 tLm sections of the distal femoral metaphyses. Primary spongiosa bone loss occurred rapidly by 2 weeks, and secondary spongiosa bone loss occurred rapidly by 8 weeks of immobilization, and then equilibrated at 60% less bone mass than age-related controls. The negative bone balance induced by immobilization was caused by transient increase in bone resorption, decrease in bone formation, and longitudinal bone growth. The dynamic data of secondary spongiosa cancellous bone showed that percent eroded perimeter was transiently elevated by 55 to 82% between 1 and 8 weeks, percent labeled perimeter was transiently depressed by 32% to 50% between 1 and 14 weeks, mineral apposition rate was depressed by 23% and 19% at I and 2 weeks, and bone formation rate-bone area referent was transiently depressed by 35% and 59% at 1 and 2 weeks. All the above parameters were at age-related control levels by 20 weeks of immobiliza- tion. However, bone formation rate-tissue area referent was depressed (-65%) throughout the study. Immobilization depressed completely longitudinal bone growth by 2 weeks and remained so. Only 0.65 mm of new metaphysis was generated in the immobilized versus 2.1 mm in controls during the study period. The immobilization induced an early cancellous bone loss which equilibrated at a new steady state with less bone and a normal (age-related control) bone turnover rate. When these findings were compared to an earlier study of 9-month-old virgin females subjected to right hindlimb immobilization up to 26 weeks, we found the adaptive responses of the cancellous bone were identical except that they occurred earlier and equilibrated sooner in younger rats.

Chen, Meng-Meng↗

NASA NTRS2006

Model-Unified Planning and Execution for Distributed Autonomous System Control

The Intelligent Distributed Execution Architecture (IDEA) is a real-time architecture that exploits artificial intelligence planning as the core reasoning engine for interacting autonomous agents. Rather than enforcing separate deliberation and execution layers, IDEA unifies them under a single planning technology. Deliberative and reactive planners reason about and act according to a single representation of the past, present and future domain state. The domain state behaves the rules dictated by a declarative model of the subsystem to be controlled, internal processes of the IDEA controller, and interactions with other agents. We present IDEA concepts - modeling, the IDEA core architecture, the unification of deliberation and reaction under planning - and illustrate its use in a simple example. Finally, we present several real-world applications of IDEA, and compare IDEA to other high-level control approaches.

Aschwanden, Pascal↗

NASA NTRS2019

Controls and Automation Research in Space Life Support

A highly controlled and automated life support system has long been a NASA goal. It is usually assumed that life support for future long duration missions will use physical/chemical recycling systems that substantially close the oxygen and water circulation loops. Such a tightly coupled life support system has been thought to require an overall supervisory control system to minimize crew operation and maintenance activities. The International Space Station (ISS) Environmental Control and Life Support System (ECLSS) was at first expected to have supervisory control and automation. After this was found infeasible during the design of the ISS ECLSS in the early 1990's, it was then expected that the ISS or future mission systems would be upgraded to meet the original expectations. Since then NASA has extensively researched life support system controls and automation. Automation and Artificial Intelligence (AI) have gone through several cycles of enthusiasm and neglect before their recent great achievements, and NASA life support interest has similarly varied. Since the ISS ECLSS was launched, its on-board operational problems have led NASA to deemphasize system level controls and automation in favor of improving subsystem reliability and maintainability. Recent work has investigated supervisory control for a system similar to the ISS ECLSS. This paper reviews past planning and work on the supervisory control of closed, integrated physical/chemical life support systems similar to the ISS ECLSS and its precursors dating back to the 1960's.

life support↗

NASA NTRSDate not supplied

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

In support of emission and fuel burn reduction goals, the aviation industry is actively pursuing the advancement of electrified aircraft propulsion (EAP) technology. This includes turboelectric and hybrid electric propulsion designs that combine gas turbine engine and electrical system hardware. Such architectures exhibit a high degree of coupling between subsystems. This drives the need for system-level control strategies to ensure the safe, coordinated, and efficient operation of all subsystems. The design and certification of any aircraft propulsion system requires that all potential subsystem failures are identified, and the hazards posed by these failures are appropriately mitigated. This requirement is particularly challenging for EAP systems due to their integrated nature. One approach to assist in EAP failure mitigation is the inclusion of automated reconfiguration capabilities within the propulsion control system. Such control modes, referred to as reversionary control modes, are designed to automatically detect failures and activate backup control modes upon failure detection. This paper covers the design and evaluation of reversionary control mode logic developed for a partially turboelectric propulsion concept. Test results from a real-time hardware-in-the-loop evaluation of the concept are also presented and discussed. The results show that the developed reversionary control logic can successfully detect and mitigate subsystem failures in a representative environment that includes actual electrical system hardware.

Electrified Aircraft Propulsion↗

NASA NTRSDate not supplied

Reversionary Control Modes for the Mitigation of Failures in a Partially Turboelectric Aircraft Propulsion System

Electrified Aircraft Propulsion↗