Search NASA⌕ Search

SEARCH · Search NASA

Results for “Lifting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Aeroelastic Trim Drag Optimization of Mach 0.8 Transonic Truss-Braced Wing Aircraft using High-Lift Devices and Control Surfaces

This paper presents an aeroelastic trim drag optimization study of the Mach 0.8 Transonic Truss-Braced Wing (TTBW) aircraft using the High-lift devices and control surfaces. An aero-structural analysis solver VSPAERO with transonic small disturbance, integral boundary-layer, and wing-strut interference corrections coupled to mode shapes computed by NASTRAN using the Galerkin method is developed to provide a rapid aircraft aeroelastic performance evaluation. Three different flight conditions corresponding to Mach 0.8 are selected for the aeroelastic trim drag optimization at the design and off-design cruise lift coefficients. The preliminary optimization results show that the TTBW aircraft with the optimized deflection of the high-lift devices and control surfaces achieves a drag reduction of about 8.2 counts, 6.5 counts, and 9.7 counts corresponding to the lift coefficients 0.661, 0.695, and 0.729, respectively. A high-fidelity CFD solver FUN3D is used to verify the aeroelastic trim drag optimization.

TTBW↗
NASA NTRS2022

Semispan Test Results of a Conventional High-Lift Common Research Model in Landing Configuration

A 10%-scale high-lift version of the Common Research Model (CRM-HL) was tested in the 14- by 22-Foot Subsonic Tunnel at the NASA Langley Research Center. This research was aimed at providing a representative reference case for comparison with an Active Flow Control (AFC) enabled version of the CRM-HL and to increase the existing experimental database for CFD high-lift prediction. The test was conducted mostly at a freestream Mach number of 0.20. The effects of the engine nacelle, nacelle chine, tufts, small variations in Mach number, hysteresis-associated increasing/decreasing angle of attack, and incoming floor boundary-layer thickness (i.e., thinning by activation of the floor boundary layer removal system) were examined. A prestall lift performance degradation for the CRM-HL configuration was resolved with a properly placed nacelle chine. Surface pressure results are presented in detail for three key variants of CRM-HL — baseline (nacelle on), nacelle off, and nacelle with the most effective chine installation. The presented aerodynamic forces and surface pressures include both with and without the wall correction using the Transonic Wall Interference Correction System (TWICS) method. A limited set of photogrammetry results is also presented to document the model deformation under test conditions.

high-lift↗
NASA NTRS1970

Background and current status of the lifting body program

The lifting body concept was originally conceived by the Ames Research Center, and the design was developed over a period of years, from 1957 to 1964. By using a cone as a basic entry shape and modifying it to obtain lift and control, the M-2 shape evolved. In a cooperative venture with the NASA Ames Research Center to determine if a pilot could maneuver, flare, and land this class of vehicle, the Flight Research Center constructed a lightweight version of the lifting body, the M2-F1 vehicle. This vehicle was constructed during the fall of 1962 and spring of 1963 and extensively flight tested during the summer of 1963. Because of the success of the M2-F1 flight program, the research program was extended to include vehicles that would be representative of mission weight and wing loading. Figure 1 shows the three vehicles in the present lifting body program. On the left is the X-24A vehicle, which evolved from the U. S. Air Force's SV-5 PRIME vehicle; in the center is the M2-F3 vehicle, which is a modified version of the M2-F2 vehicle; and on the right is the HL-10 vehicle, which evolved from work at the NASA Langley Research Center.

John G McTigue↗
NASA NTRS1970

Performance characteristics of the lifting body vehicle

Designers have relied heavily upon aerodynamic theory and wind-tunnel testing of large and small models to obtain accurate estimates of the performance characteristics for a new configuration and to provide a realistic simulation of the vehicle’s flying characteristics before its first flight, However, the highly unusual shapes of the lifting body vehicles have raised some questions of how accurately their lift and drag characteristics could be defined with these prediction techniques. Thus it is pertinent to com- pare the lift and drag data obtained in flight for three lifting body vehicles (ref. 1 and unpublished results) with wind-tunnel measurements obtained on the actual flight vehicles (refs. 2 and 3 and unpublished results) and on small-scale models of the flight vehicles (ref. 4 and unpublished results). These comparisons, together with discussions of separated flow problems and the effects of ablated surfaces, should be useful to the designers of space shuttlecraft.

Jon S Pyle↗
NASA NTRS1972

Wind tunnel study of slot spoilers for direct lift control

An investigation was conducted in a 300-mph 7- by 10- foot tunnel to obtain data for a slot spoiler direct lift control system. Slot spoilers are believed to have advantages over flap-type direct lift control (DLC) systems because of the small amount of power required for actuation. These tests, run at a Reynolds number of 1,400,000 showed that up to 78 percent of the lift due to flap deflection could be spoiled by opening several spanwise slots within the flaps. For a given lift change the drag change was significantly less than that which would be obtained by a variable flap DLC system. A nozzle-shaped slot was the most effective of the slot shapes tested.

Andrisani, D., II↗
NASA NTRS1972

A prediction model for lift-fan simulator performance

The performance characteristics of a model VTOL lift-fan simulator installed in a two-dimensional wing are presented. The lift-fan simulator consisted of a 15-inch diameter fan driven by a turbine contained in the fan hub. The performance of the lift-fan simulator was measured in two ways: (1) the calculated momentum thrust of the fan and turbine (total thrust loading), and (2) the axial-force measured on a load cell force balance (axial-force loading). Tests were conducted over a wide range of crossflow velocities, corrected tip speeds, and wing angle of attack. A prediction modeling technique was developed to help in analyzing the performance characteristics of lift-fan simulators. A multiple linear regression analysis technique is presented which calculates prediction model equations for the dependent variables.

Yuska, J. A.↗
NASA NTRS1973

Low speed wind tunnel investigation of a large scale lift fan STOL transport model

The low-speed aerodynamic characteristics of large scale V/STOL transport models with lift fan and lift-cruise fan propulsion systems are discussed. The model of this investigation had two fans mounted side by side in the nose section of the fuselage. This permitted a reasonably deep inlet on the inboard side of each fan while the outboard side had a fairly shallow inlet. Lift-cruise fans were installed on the aft section of the fuselage. Hood-type deflection ducts were used to turn the fan flow from the cruise direction to the lift direction for STOL performance. Fan performance is shown for all four fans both statically and with crossflow. Longitudinal force and moment results are shown for a representative tip speed (forward speed) range through wing supported flight. Lateral-directional characteristics are also presented. The results are presented without analysis.

Atencio, A., Jr.↗
NASA NTRS1973

Control of turbofan lift engines for VTOL aircraft.

This paper presents the results of an analytical study of the dynamics and control of turbofan lift engines, and proposes methods of meeting the response requirements imposed by the VTOL aircraft application. Two types of lift fan engines are discussed: the integral and remote. The integral engine is a conventional two-spool, high bypass ratio turbofan designed for low noise and short length. The remote engine employs a gas generator and a lift fan which are separated by a duct, and which need not be coaxial. For the integral engine, a control system design is presented which satisfies the VTOL response requirements. For the remote engine, two unconventional methods of control involving flow transfer between lift units are discussed.

Sellers, J. F.↗
NASA NTRS1975

High-lift aerodynamics: Trends, trades, and options

The trend toward the utilization of higher maximum lift coefficient with increased aircraft size and cruise velocities is discussed. The impact of this trend on the need for tradeoffs between cruise performance and takeoff, climb, and landing performance is examined. Theoretical methods for the analysis of the two-dimensional characteristics of flap systems are described and compared with experimental data. Four powered-lift concepts are described to outline some of the options currently being developed. Two jet-flap theories are described which provide analytical methods for estimation of the three-dimensional aerodynamic high-lift performance characteristics of powered lift systems.

Margason, R. J.↗
NASA NTRS1975

Factors affecting handling qualities of a lift-fan aircraft during steep terminal area approaches

The XV-5B lift-fan aircraft was used to explore the factors affecting handling qualities in the terminal area. A 10 deg ILS approach task was selected to explore these problems. Interception of the glide slope at 457.2 m, glide slope tracking, deceleration along the glide slope to a spot hover were considered. Variations in airplane deck angle, deceleration schedule, and powered-lift management were studied. The overall descent performance envelope was identified on the basis of fan stall, maximum comfortable descent rate, and controllability restrictions. The collective-lift stick provided precise glide slope tracking capability. The pilot preferred a deck-parallel attitude for which he used powered lift to control glide slope and pitch attitude to keep the angle of attack near zero. Workload was reduced when the deceleration schedule was delayed until the aircraft was well established on the glide slope, since thrust vector changes induced flight path disturbances.

Gerdes, R. M.↗
NASA NTRS1975

Analysis of transonic flow about lifting wing-body configurations

An analytical solution was obtained for the perturbation velocity potential for transonic flow about lifting wing-body configurations with order-one span-length ratios and small reduced-span-length ratios and equivalent-thickness-length ratios. The analysis is performed with the method of matched asymptotic expansions. The angles of attack which are considered are small but are large enough to insure that the effects of lift in the region far from the configuration are either dominant or comparable with the effects of thickness. The modification to the equivalence rule which accounts for these lift effects is determined. An analysis of transonic flow about lifting wings with large aspect ratios is also presented.

Barnwell, R. W.↗
NASA NTRS1975

Summary of model VTOL lift fan tests conducted at NASA Lewis Research Center

The purpose of the tests was to obtain overall performance and influencing factors as well as detailed measurements of the internal flow characteristics. The first experiment consisted of crossflow tests of a 15-inch diameter fan installed in a two-dimensional wing. Tests were run with and without exit louvers over a range of tunnel speeds, fan speeds, and wing angle of attack. The wing was used for a study of installation effects on lift fan performance. The model tested consisted of three 5.5-inch diameter tip-turbine driven model VTOL lift fans mounted chord-wise in the two-dimensional wing to simulate a pod-type array. Several inlet and exit cover door configurations and an adjacent fuselage panel were tested. For the third program, a pod was attached to the wing, and an investigation was conducted of the effect of design tip speed on the aerodynamic performance and noise of a 15-inch diameter lift fan-in-pod under static and crossflow conditions. Three single VTOL lift fan stages were designed for the same overall total pressure ratio but at three different rotor tip speeds.

Diedrich, J. H.↗
NASA NTRS1975

Effects of spanwise blowing on the pressure field and vortex-lift characteristics of a 44 deg swept trapezoidal wing

Wind-tunnel data were obtained at a free-stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and jet location. Results of this study show that the sectional effects to spanwise blowing are strongly dependent on angle of attack, jet thrust coefficient, and span location; the largest effects occur at the highest angles of attack and thrust coefficients and on the inboard portion of the wing. Full vortex lift was achieved at the inboard span station with a small blowing rate, but successively higher blowing rates were necessary to achieve full vortex lift at increased span distances. It is shown that spanwise blowing increases lift throughout the angle-of-attack range, delays wing stall to higher angles of attack, and improves the induced-drag polars. The leading-edge suction analogy can be used to estimate the section and total lifts resulting from spanwise blowing.

Campbell, J. F.↗
NASA NTRS1975

Aerodynamic lift effect on satellite orbits

Numerical quadrature is employed to obtain orbit perturbation results from the general perturbation equations. Both aerodynamic lift and drag forces are included in the analysis of the satellite orbit. An exponential atmosphere with and without atmospheric rotation is used. A comparison is made of the perturbations which are caused by atmospheric rotation with those caused by satellite aerodynamic effects. Results indicate that aerodynamic lift effects on the semi-major axis and orbit inclination can be of the same order as the effects of atmosphere rotation depending upon the orientation of the lift vector. The results reveal the importance of including aerodynamic lift effects in orbit perturbation analysis.

Karr, G. R.↗
NASA NTRS1975

Augmentation of vortex lift by spanwise blowing

An investigation has been conducted to evaluate the aerodynamic effects associated with blowing a jet spanwise over a wing's upper surface in a direction parallel to the leading edge. Experimental pressure and force data were obtained on wings with sweep angles of 30 and 45 degrees and showed that spanwise blowing aids in the formation and control of the leading-edge vortex and, hence, significantly improves the aerodynamic characteristics at high angles of attack. Full vortex section lift is achieved at the inboard span station with a small blowing rate, but successively higher blowing rates are necessary to attain the full vortex-lift level at increased span distances. Spanwise blowing generates large increases in lift at high angles of attack, improves the drag polars, and extends the linear pitching moment to high lifts.

Campbell, J. F.↗
NASA NTRS1975

Summary of model VTOL lift fan tests conducted at NASA Lewis Research Center

Early in this decade three model VTOL lift fan studies were conducted in the NASA Lewis Research Center's 9- by 15-foot V/STOL wind tunnel. The first experiment consisted of crossflow tests of a 15-inch diameter fan installed in a two-dimensional wing. The wing was then used for a study of installation effects on lift fan performance. The model tested consisted of three 5.5-inch diameter tip-turbine driven model VTOL lift fans mounted chord-wise in the two-dimensional wing to simulate a pod-type array. For the third program, a pod was attached to the wing, and an investigation was conducted of the effect of design tip speed on the aerodynamic performance and noise of a 15-inch diameter lift fan-in-pod under static and crossflow conditions.

Diedrich, J. H.↗
NASA NTRS1975

Ultra-heavy vertical lift system: The Heli-Stat

A hybrid VTOL airship which is combined with helicopters is evaluated. The static lift of the airship supports approximately the full empty weight of the entire assembly. The helicopter rotors furnish the lift to support the payload as well as the propulsion and control about all axes. Thus existing helicopters, with no new technology required, can be made to lift payloads of ten times the capacity of each one alone, and considerably more than that of any airship built so far. A vehicle is described which has a 75-ton payload, based on four existing CH-53D helicopters and an airship of 3,600,000 cu. ft. The method of interconnection is described along with discussion of control, instrumentation, drive system and critical design conditions. The vertical lift and positioning capabilities of this vehicle far exceed any other means available today, yet can be built with a minimum of risk, development cost and time.

Piasecki, F. N.↗
NASA NTRS1975

Shear flow aerodynamics - Lifting surface theory

A lifting surface theory based on a parallel shear flow model is presented for steady, incompressible flows. The theory is intended to account approximately for the presence of a boundary layer. The method of Fourier transforms is used to calculate the pressure on a surface of infinite extent and arbitrary contour. Immediately above the surface is a region of sheared flow (the boundary layer), outside of which the flow velocity is constant. The Fourier transform of the pressure on this surface is used to derive the shear flow equivalent to the kernel function of classical potential flow lifting surface theory. The kernel function provides an integral relation between the upwash at a given point on the surface and the pressure everywhere on the surface. This relation is treated as an integral equation for the pressure, and is solved numerically. Computations are presented for the lift and pitching moment on a flat plate in two-dimensional flow, and for flat, rectangular wings of aspect ratio 1, 2, and 5. As expected, the shear layer decreases the lift curve slope; however, the shear layer (whose thickness is constant along the wing chord) has little effect on the center of pressure.

Ventres, C. S.↗