Search NASA⌕ Search

SEARCH · Search NASA

Results for “Low Creep”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

High-temperature fatigue in metals - A brief review of life prediction methods developed at the Lewis Research Center of NASA

The presentation focuses primarily on the progress we at NASA Lewis Research Center have made. The understanding of the phenomenological processes of high temperature fatigue of metals for the purpose of calculating lives of turbine engine hot section components is discussed. Improved understanding resulted in the development of accurate and physically correct life prediction methods such as Strain-Range partitioning for calculating creep fatigue interactions and the Double Linear Damage Rule for predicting potentially severe interactions between high and low cycle fatigue. Examples of other life prediction methods are also discussed. Previously announced in STAR as A83-12159

Halford, G. R.↗

Exposure time considerations in high temperature low cycle fatigue

The Conventional Strainrange Partitioning (CSRP) method for High-Temperature, Low-Cycle Fatigue (HTLCF) life prediction has its origins in the modeling of first-order, creep-fatigue waveform effects while treating as second-order effects, the influence of metallurgical or environmental time dependencies. Procedures are proposed to include the latter explicitly in the inelastic strainrange--life relations. For brevity, only the CP life relation will be presented in detail. The exposure-time effect within the CP inelastic strainrange (tensile creep reversed by compressive plasticity) was determined by tensile stresshold-time experiments for 316 SS at 816 C. Reductions in CP cyclic life of a factor of about two were observed with an increase in exposure time or a corresponding decrease in creep rate by a factor of about 100. The CP life relation has been modified to be expressed in terms of either Steady State Creep Rate (SSCR) or Exposure Time (ET). The applicability and accuracy of the time-dependent CP life relations is demonstrated by conducting verification experiments involving complex hysteresis loops. Metallographic examination revealed time-dependent degradation attributable to oxide formation and precipitation of carbides along grain boundaries.

Kalluri, S.↗

Exposure time considerations in high temperature low cycle fatigue

The Conventional Strainrange Partitioning (CSRP) method for High-Temperature, Low-Cycle Fatigue (HTLCF) life prediction has its origins in the modeling of first-order, creep-fatigue waveform effects while treating as second-order effects, the influence of metallurgical or environmental time dependencies. Procedures are proposed to include the latter explicitly in the inelastic strainrange-life relations. For brevity, only the CP life relation will be presented in detail. The exposure-time effect within the CP inelastic strainrange (tensile creep reversed by compressive plasticity) was determined by tensile stresshold-time experiments for 316 SS at 816 C. Reductions in CP cyclic life of a factor of about two were observed with an increase in exposure time or a corresponding decrease in creep rate by a factor of about 100. The CP life relation has been modified to be expressed in terms of either Steady State Creep Rate (SSCR) or Exposure Time (ET). The applicability and accuracy of the time-dependent CP life relations is demonstrated by conducting verification experiments involving complex hysteresis loops. Metallographic examination revealed time-dependent degradation attributable to oxide formation and precipitation of carbides along grain boundaries.

Kalluri, S.↗

Accelerated Near-Threshold Fatigue Crack Growth Behavior of an Aluminum Powder Metallurgy Alloy

Fatigue crack growth (FCG) research conducted in the near threshold regime has identified a room temperature creep crack growth damage mechanism for a fine grain powder metallurgy (PM) aluminum alloy (8009). At very low DK, an abrupt acceleration in room temperature FCG rate occurs at high stress ratio (R = Kmin/Kmax). The near threshold accelerated FCG rates are exacerbated by increased levels of Kmax (Kmax less than 0.4 KIC). Detailed fractographic analysis correlates accelerated FCG with the formation of crack-tip process zone micro-void damage. Experimental results show that the near threshold and Kmax influenced accelerated crack growth is time and temperature dependent.

Piascik, Robert S.↗

Accelerated Threshold Fatigue Crack Growth Effect-Powder Metallurgy Aluminum Alloy

Fatigue crack growth (FCG) research conducted in the near threshold regime has identified a room temperature creep crack growth damage mechanism for a fine grain powder metallurgy (PM) aluminum alloy (8009). At very low (Delta) K, an abrupt acceleration in room temperature FCG rate occurs at high stress ratio (R = K(sub min)/K(sub max)). The near threshold accelerated FCG rates are exacerbated by increased levels of K(sub max) (K(sub max) = 0.4 K(sub IC)). Detailed fractographic analysis correlates accelerated FCG with the formation of crack-tip process zone micro-void damage. Experimental results show that the near threshold and K(sub max) influenced accelerated crack growth is time and temperature dependent.

Piascik, R. S.↗

Influence of Constituents on Creep Properties of SiC/SiC Composites

SiC-SiC composites are being considered as potential candidate materials for next generation turbine components such as combustor liners, nozzle vanes and blades because of their low density, high temperature capability, and tailorable mechanical properties. These composites are essentially fabricated by infiltrating matrix into a stacked array of fibers or fiber preform by one or a combination of manufacturing methods such as, Melt Infiltration (MI) of molten silicon metal, Chemical Vapor Infiltration (CVI), Polymer Infiltration and Pyrolysis (PIP). To understand the influence of constituents, the SiC-SiC composites fabricated by MI, CVI, and PIP methods were creep tested in air between 12000 and 14500 degrees Centigrade for up to 500 hours. The failed specimens were analyzed under a scanning electron microscope to assess damage mechanisms. Also, knowing the creep deformation parameters of the fiber and the matrix under the testing conditions, the creep behavior of the composites was modeled and compared with the measured data. The implications of the results on the long term durability of these composites will be discussed.

modeling↗

Porosity and the ecology of icy satellites

The case for a significant role for porosity in the structure and evolution of icy bodies in the Solar System has been difficult to establish. We present a relevant new data set and a series of structure models including a mechanical compression, not thermal creep, model for porosity that accounts satisfactorily for observed densities, moments of inertia, geologic activity, and sizes of tectonic features on icy satellites. Several types of observational data sets have been used to infer significant porosity, but until recently, alternative explanations have been preferred. Our first area of concern is the occurrence of cryovolcanism as a function of satellite radius; simple radiogenic heating models of icy satellites suggest minimum radii for melting and surface cryovolcanism to be 400 to 500 km, yet inferred melt deposits are seen on satellites half that size. One possible explanation is a deep, low conductivity regolith which lowers conductivity and raises internal temperatures, but other possibilities include tidal heating or crustal compositions of low conductivity. Our second area of concern is the occurrence and magnitude of tectonic strain; tectonic structures have been seen on icy satellites as small as Mimas and Proteus. The structures are almost exclusively extensional, with only a few possible compression Al features, and inferred global strains are on the order of 1 percent expansion. Expansions of this order in small bodies like Mimas and prevention of late compressional tectonics due to formation of ice mantles in larger bodies like Rhea are attained only in structure models including low-conductivity, and thus possibly high porosity, crusts. Thirdly, inferred moments of inertia less than 0.4 in Mimas and Tethys can be explained by high-porosity crusts, but also by differentiation of a high density core. Finally, the relatively low densities of smaller satellites like Mimas and Miranda relative to larger neighbors can be explained by deep porosity, but also by bulk compositional differences. Recent work has strengthened the case for significant porosity. Halley's nucleus was found to have a density near 0.6 g/cu cm, Janus and Epimethus were proposed to have densities near 0.7 g/cu cm, densities almost certainly due to high porosity. The irregular-spherical shape transition of icy satellites was quantitatively explained by low conductivity regoliths. A creative structure/thermal history model for Mimas simultaneously accounts quantitatively for Mimas' low density and moment of inertia by invoking initial high-porosity and subsequent compaction in the deep interior by thermal creep. The main problem with this promising model is that approximately 7 percent predicts a reduction in Mimas' radius, implying significant compressional failure and prevention of extensional tectonics, in contradiction to the observed extensional features and inferred 1 percent expansion in radius.

Croft, Steven K.↗

Versatile Turbine Disk Alloy Designed and Processed for Higher Temperature Applications

Advanced turbine engine configurations using higher temperature combustor and airfoil concepts require compressor and turbine disks that can withstand temperatures higher than the 650 C typical of current engines. This requires disk alloy and processing improvements. A versatile disk alloy was needed that could be given either fine grain heat treatments for high strength and fatigue and creep resistance up to 704 C or given coarse grain heat treatments for high strength and creep and dwell crack-growth resistance at higher temperatures. This alloy could produce disks with uniform microstructures and properties, as well as with varied, optimized microstructures at disk bore and rim sections. A series of experimental disk alloys were designed and processed to give subscale disks about 13 cm in diameter and 4 cm thick. These alloys had varying levels of key elements to affect mechanical properties and change the "solvus" solution heat-treatment temperature necessary to produce coarse grain microstructures. Disks were given coarse grain heat treatments followed by rapid oil quenching and slower fan air quenching. These heat treatments were intended to simulate the cooling paths of rapidly cooled full-scale disks at the outermost rim and interior bore locations, respectively. Preliminary quench tests of tensile specimens and coin-size minidisks had indicated that alloys having high solvus temperatures were more prone to cracking during rapid quenching from coarse grain heat treatments. These findings were confirmed in the subscale disks, where such alloys did form undesirable quench cracks. Mechanical tests were performed on specimens from subscale disks given these coarse grain heat treatments, as well as on specimens given a fine grain heat treatment. Tensile, creep, and crack growth tests were performed at 704 C and higher temperatures. A versatile alloy was identified that had a low solvus temperature for resistance to quench cracking as well as an optimal combination of high levels of strengthening refractory elements that produced balanced high mechanical properties for both fine grain and coarse grain microstructures. This low-solvus, high-refractory (LSHR) alloy has been scaled-up to produce prototype full-scale turbine disks typical of regional jet turbofan engines. Disks were successfully heat treated to give uniform coarse grain and uniform fine grain microstructures. Additional disks were given a NASA dual microstructure heat treatment (DMHT) that intentionally varied the solution heat-treatment temperatures between the disk rim and bore (re f. 1). The disk rim was heated to a high enough temperature to produce a coarse grain microstructure, while the bore was maintained at a lower temperature to produce a fine grain microstructure (see the figure). This DMHT can produce optimal high strength, fatigue, and creep resistance up to 704 C in the cooler running disk bore, and high strength, creep resistance, and dwell crack growth resistance at higher temperatures for the hotter disk rim. Extensive mechanical testing is being initiated to compare the mechanical properties of the uniform and DMHT disks.

Gabb, TImothy P.↗

A New Approach of Designing Superalloys for Low Density

New low-density single-crystal (LDS) alloy, have bee. developed for turbine blade applications, which have the potential for significant improvements in the thrust-to-weight ratio over current production superalloys. An innovative alloying strategy was wed to achieve alloy density reductions, high-temperature creep resistance, microstructural stability, and cyclic oxidation resistance. The alloy design relies on molybdenum as a potent. lower-density solid-solution strengthener in the nickel-based superalloy. Low alloy density was also achieved with modest rhenium levels tmd the absence of tungsten. Microstructural, physical mechanical, and environmental testing demonstrated the feasibility of this new LDS superalloy design.

MacKay, Rebecca A.↗

Creep-rupture performance of superalloys in high-pressure hydrogen environment

The advantages of the automotive Stirling engine presented, which employs high-pressure hydrogen as a working fluid, include (in addition to a 50-percent improvement in efficiency over internal combustion engines) multiple-fuel capability, low pollution, and low noise. The severe service conditions associated with the 870 C operation and 15 MPa hydrogen working fluid have prompted the present suitability testing of six tube and four cast Fe-base alloys. While stress-rupture life and minimum creep rates were not affected, both tube and cast alloy types underwent creep ductility degradation.

Bhattacharyya, S.↗

Thermal barrier coating life prediction model

This is the first report of the first phase of a 3-year program. Its objectives are to determine the predominant modes of degradation of a plasma sprayed thermal barrier coating system, then to develop and verify life prediction models accounting for these degradation modes. The first task (Task I) is to determine the major failure mechanisms. Presently, bond coat oxidation and bond coat creep are being evaluated as potential TBC failure mechanisms. The baseline TBC system consists of an air plasma sprayed ZrO2-Y2O3 top coat, a low pressure plasma sprayed NiCrAlY bond coat, and a Rene'80 substrate. Pre-exposures in air and argon combined with thermal cycle tests in air and argon are being utilized to evaluate bond coat oxidation as a failure mechanism. Unexpectedly, the specimens pre-exposed in argon failed before the specimens pre-exposed in air in subsequent thermal cycles testing in air. Four bond coats with different creep strengths are being utilized to evaluate the effect of bond coat creep on TBC degradation. These bond coats received an aluminide overcoat prior to application of the top coat to reduce the differences in bond coat oxidation behavior. Thermal cycle testing has been initiated. Methods have been selected for measuring tensile strength, Poisson's ratio, dynamic modulus and coefficient of thermal expansion both of the bond coat and top coat layers.

Hillery, R. V.↗

Bayonet for superfluid helium transfer in space

A prototype superfluid helium bayonet for potential space applications has been developed and evaluated with a low heat leak test apparatus. Measured heat leak of the 13 mm (1/2 inch) bayonet pair is 0.21 W at 1.8 K with an uncertainty of +0.09/-0.05 W. Bayonets are fabricated with thin, electron beam (EB) welded tubes which are EB welded to machined nose and flange pieces. Low heat leak structural integrity is provided by a 0.9 mm thickness of filament wound fiberglass-epoxy. Superfluid creep is restricted by KEL-F nose seals which form vacuum-tight extensions to the bayonet cold end pieces.

Mcintosh, G. E.↗

Overview of High Temperature Material Needs for Space Nuclear Propulsion Reactors

Space nuclear propulsion systems are capable of enabling future crewed missions to Mars. Two primary options of these systems exist: nuclear thermal propulsion (NTP) and nuclear electric propulsion (NEP). NTP systems use a reactor as a heat exchanger to heat a hydrogen propellant to produce high specific impulse (≥ 900 s) and thrust (10 - 100 klbf). A NTP materials challenge is development of nuclear fuel capable of operating for short durations (hours) under high power densities (≥ 5 MW/L) and temperatures (> 2700 K) in a corrosive hydrogen environment. In NEP systems, the reactor heats a working fluid which transfers heat to a power conversion system to power electric thrusters. NEP is capable of higher specific impulse (≥ 2000 s) but limited to low thrust (10s lbf). Light weight vessel and in-core structural materials that are radiation-resistant, creep-resistant, and dimensionally stable while operating at ~1500 K over mission times up to several years are needed for NEP. Both systems can benefit from high temperature neutron moderators. Through the Space Nuclear Propulsion project, NASA, supported by the DOE, is developing NTP and NEP systems. Technology maturation planning and risk reduction activities related to fabrication and testing of reactor material candidates is ongoing. This presentation overviews NTP and NEP materials needs and current ceramic and composite development activities.

nuclear thermal propulsion↗

Mechanical properties of modified low cobalt powder metallurgy Udimet 700 type alloys

Eight superalloys derived from Udimet 700 were prepared by powder metallurgy, hot isostatically pressed, heat treated and their tensile and creep rupture properties determined. Several of these alloys displayed properties superior to those of Udimet 700 similarly prepared, in one case exceeding the creep rupture life tenfold. Filter clogging by extracted gamma prime, its measurement and significance are discussed in an appendix.

Harf, Fredric H.↗

Experimental and theoretical investigation of fatigue life in reusable rocket thrust chambers

During a test program to investigate low-cycle thermal fatigue, 13 rocket combustion chambers were fabricated and cyclically test fired to failure. Six oxygen-free, high-conductivity (OFHC) copper and seven Amzirc chambers were tested. The failures in the OFHC copper chambers were not typical fatigue failures but are described as creep rupture enhanced by ratcheting. The coolant channels bulged toward the chamber centerline, resulting in progressive thinning of the wall during each cycle. The failures in the Amzirc alloy chambers were caused by low-cycle thermal fatigue. The zirconium in this alloy was not evenly distributed in the chamber materials. The life that was achieved was nominally the same as would have been predicted from OFHC copper isothermal test data.

Hannum, N. P.↗

Compatibility of potential reinforcing ceramics with Ni and Fe aluminides

There is a great deal of interest in the possible utilization of intermetallic compounds in advanced high temperature gas turbine engines. These compounds exhibit a variety of promising properties, including reasonable strength, high melting points, relatively low densities, and good corrosion resistance. However, in general, they also show limited ductilities and toughness, and less than optimum creep strengths at elevated temperatures. In addition, in applications involving advanced gas turbine engines, it is often necessary for candidate materials to have large elastic moduli. The present study is part of a program whose objective is to identify a high temperature fiber reinforced composite. The approach adopted was to fabricate laboratory samples of the combinations of materials considered by Misra, in order to determine the extent to which the thermodynamic calculations can predict phase stability. As many of the ceramic phases considered are not currently available in fiber form, they were added as particulates to the alloy matrices. The ways in which the materials were produced and evaluated are described.

Clark, William A. T.↗

Forging of Advanced Disk Alloy LSHR

The powder metallurgy disk alloy LSHR was designed with a relatively low gamma precipitate solvus temperature and high refractory element content to allow versatile heat treatment processing combined with high tensile, creep and fatigue properties. Grain size can be chiefly controlled through proper selection of solution heat treatment temperatures relative to the gamma precipitate solvus temperature. However, forging process conditions can also significantly influence solution heat treatment-grain size response. Therefore, it is necessary to understand the relationships between forging process conditions and the eventual grain size of solution heat treated material. A series of forging experiments were performed with subsequent subsolvus and supersolvus heat treatments, in search of suitable forging conditions for producing uniform fine grain and coarse grain microstructures. Subsolvus, supersolvus, and combined subsolvus plus supersolvus heat treatments were then applied. Forging and subsequent heat treatment conditions were identified allowing uniform fine and coarse grain microstructures.

Gabb, Timothy P.↗

Development and Performance Evaluations of HfO2-Si and Rare Earth-Si Based Environmental Barrier Bond Coat Systems for SiC/SiC Ceramic Matrix Composites

Ceramic environmental barrier coatings (EBC) and SiCSiC ceramic matrix composites (CMCs) will play a crucial role in future aircraft propulsion systems because of their ability to significantly increase engine operating temperatures, improve component durability, reduce engine weight and cooling requirements. Advanced EBC systems for SiCSiC CMC turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant material development challenges for the high temperature CMC components is to develop prime-reliant, high strength and high temperature capable environmental barrier coating bond coat systems, since the current silicon bond coat cannot meet the advanced EBC-CMC temperature and stability requirements. In this paper, advanced NASA HfO2-Si based EBC bond coat systems for SiCSiC CMC combustor and turbine airfoil applications are investigated. The coating design approach and stability requirements are specifically emphasized, with the development and implementation focusing on Plasma Sprayed (PS) and Electron Beam-Physic Vapor Deposited (EB-PVD) coating systems and the composition optimizations. High temperature properties of the HfO2-Si based bond coat systems, including the strength, fracture toughness, creep resistance, and oxidation resistance were evaluated in the temperature range of 1200 to 1500 C. Thermal gradient heat flux low cycle fatigue and furnace cyclic oxidation durability tests were also performed at temperatures up to 1500 C. The coating strength improvements, degradation and failure modes of the environmental barrier coating bond coat systems on SiCSiC CMCs tested in simulated stress-environment interactions are briefly discussed and supported by modeling. The performance enhancements of the HfO2-Si bond coat systems with rare earth element dopants and rare earth-silicon based bond coats are also highlighted. The advanced bond coat systems, when integrated with advanced EBC top coats, showed promise to achieve 1500 C temperature capability, helping enable next generation turbine engines with significantly improved engine component temperature capability and long-term durability.

HfO2-Si bond coat↗