Search NASA⌕ Search

SEARCH · Search NASA

Results for “MACH NUMBER EFFECTS - PROPELLERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Aerodynamics of spheres for Mach numbers from 0.6 to 10.5 including some effects of test conditions

Wind tunnel tests were made for spheres of various sizes over a range of Mach numbers and Reynolds numbers. The results indicated some conditions where the drag was affected by changes in the afterbody pressure due to a shock reflection from the tunnel wall. This effect disappeared when the Mach number was increased for a given sphere size or when the sphere size was decreased for a given Mach number. Drag measurements and Schlieren photographs show the possibility of obtaining inaccurate data when tests are made with a sphere too large for the test section size and Mach number. Tests were also made of an oblate spheroid. The results indicated a region at high Mach numbers where inherent positive static stability might occur with the oblate-face forward. The drag results are compared with those for a sphere and those for various other shapes. The drag results for the oblate spheriod and the sphere are also compared with some calculated results.

Spearman, M. Leroy↗
NASA NTRS1960

Measurements of Skin Friction of the Compressible Turbulent Boundary Layer on a Cone with Foreign Gas Injection

Measurements of average skin friction of the turbulent boundary layer have been made on a 15deg total included angle cone with foreign gas injection. Measurements of total skin-friction drag were obtained at free-stream Mach numbers of 0.3, 0.7, 3.5, and 4.7 and within a Reynolds number range from 0.9 x 10(exp 6) to 5.9 x 10(exp 6) with injection of helium, air, and Freon-12 (CCl2F2) through the porous wall. Substantial reductions in skin friction are realized with gas injection within the range of Mach numbers of this test. The relative reduction in skin friction is in accordance with theory-that is, the light gases are most effective when compared on a mass flow basis. There is a marked effect of Mach number on the reduction of average skin friction; this effect is not shown by the available theories. Limited transition location measurements indicate that the boundary layer does not fully trip with gas injection but that the transition point approaches a forward limit with increasing injection. The variation of the skin-friction coefficient, for the lower injection rates with natural transition, is dependent on the flow Reynolds number and type of injected gas; and at the high injection rates the skin friction is in fair agreement with the turbulent boundary layer results.

Pappas, Constantine C.↗
NASA NTRSDate not supplied

Wall-modeled LES of Flow Over a Gaussian Bump

We perform wall-modeled large eddy simulations (WMLES) of turbulent flow over a Gaussian-shaped bump geometry, to assess its performance in the accelerating and separation regions of the flow. The flow conditions are based on the ongoing CFD validation experiments of Slotnick [NATO STO-MP-AVT-307, 2019]. The oncoming flow Mach number is 0.176, and two Reynolds numbers are simulated that are about 10000 and 36000 based on boundary layer thickness upstream of the bump. Preliminary Reynolds-averaged Navier-Stokes simulations are first performed to assess the effects of Mach number, Reynolds number, tunnel top and sidewall effects. Finally, WMLES results with an equilibrium wall model will be presented at two Reynolds numbers to assess their performance for this flow by making detailed comparisons with available experimental and higher-fidelity numerical data.

turbulence, wall model, large eddy simulation↗
NASA NTRS1993

Aerodynamics of a sphere and an oblate spheroid for Mach numbers from 0.6 to 10.5 including some effects of test conditions

Wind-tunnel tests were made for spheres of various sizes over a range of Mach numbers and Reynolds numbers. The results indicated some conditions where the drag was affected by changes in the afterbody pressure due to a shock reflection from the tunnel wall. This effect disappeared when the Mach number was increased for a given sphere size or when the sphere size was decreased for a given Mach number. Drag measurements and Schlieren photographs are presented that show the possibility of obtaining inaccurate data when tests are made with a sphere too large for the test section size and Mach number. Tests were also made of an oblate spheroid. The results indicated a region at high Mach numbers where inherent positive static stability might occur with the oblate-face forward. The drag results are compared with those for a sphere as well as those for various other shapes. The drag results for the oblate spheroid and the sphere are also compared with some calculated results.

Spearman, M. Leroy↗
NASA NTRS1973

Sonic boom analysis for high altitude flight at high Mach number

Numerical programs are presented which take into account the nonlinear effects of high Mach number, the entropy change across the shock, the entropy and enthalpy variations in the atmospheric layer and the gravitational effect. Extension of the programs for the axisymmetric problems to handle nonaxisymmetric terms is described. The asymmetry can be caused by the geometry of the body, the lift and also the fact that the variations in the atmospheric layer are two-dimensional. Numerical results demonstrating the influences of these effects and comparison with existing approximate theories are presented.

Ferri, A.↗
NASA NTRS1951

Aerodynamic characteristics of four bodies of revolution showing some effects of afterbody shape and fineness ratio at free-stream Mach numbers from 1.50 to 1.99

The effects of fineness ratio (14.2 and 12.2) and boattailing on aerodynamic characteristics of four bodies of revolution at Mach numbers from 1.50 to 1.99 within a range of angles of attack from 0 degrees 10 degrees at an approximate Reynolds number of 35x10(superscript)6 based on body length were investigated. A comparison of experimental data with available theory is included. At zero angle of attack, fineness ratio has no appreciable effect on model characteristics while boattailing and boattail convergence significantly affect fore drag and base drag. At angle of attack the effects are singular. The theory presented by H. J. Allen is a significant improvement over linearized potential theory in predicting aerodynamic characteristics.

BODIES - FITNESS RATIO↗
NASA NTRS1975

Update on an investigation of flight buffeting of a variable-sweep aircraft

A detailed investigation of flight buffeting response of an F-111A aircraft was performed. AIAA Paper No. 74-358 presented results of an initial study of wing and fuselage responses measured at subsonic speeds and wing leading-edge sweep of 26 degrees. The present paper gives additional results for wing sweeps of 26, 50 and 72.5 degrees at Mach numbers up to 1.2 including horizontal tail responses. Power spectra, response time histories, variations of rms response with angle of attack, and effects of Mach number and wing sweep angle are discussed.

Benepe, D. B.↗
NASA NTRS1972

Impact probe displacement in a supersonic turbulent boundary layer.

The experiment was performed on the test section sidewall in a supersonic pressure tunnel. The boundary layer at the test station was surveyed in turn by each of 8 impact probes ranging in size from about 1.3 to 48 mm. The impact pressures measured by these probes were combined with the test section static pressure to calculate Mach numbers. Probe displacement effects were evaluated in terms of these Mach number values.

Allen, J. M.↗
NASA NTRS1985

Flight measurements of surface pressures on a flexible supercritical research wing

A flexible supercritical research wing, designated as ARW-1, was flight-tested as part of the NASA Drones for Aerodynamic and Structural Testing Program. Aerodynamic loads, in the form of wing surface pressure measurements, were obtained during flights at altitudes of 15,000, 20,000, and 25,000 feet at Mach numbers from 0.70 to 0.91. Surface pressure coefficients determined from pressure measurements at 80 orifice locations are presented individually as nearly continuous functions of angle of attack for constant values of Mach number. The surface pressure coefficients are also presented individually as a function of Mach number for an angle of attack of 2.0 deg. The nearly continuous values of the pressure coefficient clearly show details of the pressure gradient, which occurred in a rather narrow Mach number range. The effects of changes in angle of attack, Mach number, and dynamic pressure are also shown by chordwise pressure distributions for the range of test conditions experienced. Reynolds numbers for the tests ranged from 5.7 to 8.4 x 1,000,000.

Eckstrom, C. V.↗
NASA NTRS1991

Aeroacoustic flow sensor

A theoretical analysis of standing waves in a pipe with flow was conducted aimed toward the development of a flowmeter based on a measurement of phase difference between two points on the circumference of a pipe separated axially by an integral multiple of half sound wavelength. Effects of nonzero Mach number, variable ratios of upstream and downstream running waves, choice of location of the sensing pressure taps, and the incorrect spacings were examined numerically. Calculations were also made for steam flow where the maximum Mach number is much smaller than in cold air flows. For an industrial application where steam flow velocities are below 50 m/s, a very accurate sensor is shown to be possible. Experimental data were obtained by using an active aeroacoustic source over the range of 50 m/s to zero in an air flow. Experimental phase plots obtained from several coast-down tests have been compared with analytical results. The agreement with theory is excellent when the spacings are near N(lambda)/2 and the sensing locations are near the pressure antinodes. Otherwise, some zero shifts are introduced. Theory predicts that for steam flow much better results can be expected because the maximum Mach number is much smaller. Effects due to the (1-M-squared) factor would be imperceptible for steam flow.

Shakkottai, P.↗
NASA NTRS1948

Effects of sweep on controls

An analysis of the principal results of recent control-surface research pertinent to transonic flight has been made. An indication of the nature of the changes in control-surface characteristics above the critical speed of the wing and a preliminary design procedure for estimating the effectiveness of flap-type controls on swept wings are presented.

CONTROLS, FLAP TYPE - COMPLETE WINGS↗
NASA NTRS1996

Shock Tunnel Studies of Scramjet Phenomena

Work focussed on a large number of preliminary studies of supersonic combustion in a simple combustion duct - thrust nozzle combination, investigating effects of Mach number, equivalence ratio, combustor divergence, fuel injecting angle and other parameters with an influence on the combustion process. This phase lasted for some three or four years, during which strongest emphasis was placed on responding to the request for preliminary experimental information on high enthalpy effects, to support the technology maturation activities of the NASP program. As the need for preliminary data became less urgent, it was possible to conduct more systematic studies of high enthalpy combustion phenomena, and to initiate other projects aimed at improving the facilities and instrumentation used for studying scramjet phenomena at high enthalpies. The combustion studies were particularly directed towards hypersonic combustion, and to the effects of injecting fuel along the combustion chamber wall. A substantial effort was directed towards a study of the effect of scale on the supersonic combustion process. The influence of wave phenomena (both compression waves and expansion waves) on the realization of thrust from a supersonic combustion process was also investigated. The effect of chemical kinetics was looked into, particularly as it affected the composition of the test flow provided by a ground facility. The effect of injection of the fuel through wall orifices was compared with injection from a strut spanning the stream, and the effect of heating the fuel prior to injection was investigated. Studies of fuel-air mixing by shock impingement were also done, as well as mass spectrometer surveys of a combustion wake. The use of hypersonic nozzles with an expansion tube was investigated. A new method was developed for measuring the forces acting of a model in less than one millisecond. Also included in this report are listings of published journal papers and conference presentations.

Stalker, R. J.↗
NASA NTRS1957

Interference Effects of Fuselage-Stored Missiles on Inlet Duct Model of an Interceptor-Type Aircraft at Mach Numbers 1.5 to 1.9

The effect of missile armament on the performance of an interceptor-type aircraft model has been determined at Mach numbers 1.5, 1.7, and 1.9 and at angles of attack to 19 deg. With this configuration missiles were carried in a bay located on the bottom of the aircraft fuselage and mounted to a rotatable missile door. Rotation of the door then brought the missiles into the external or firing position. The aircraft model was characterized by triangular-shaped normal-shock inlets located at the wing roots. Relatively short and curved subsonic diffusers fed simulated twin side-by-side turbojet engines. Inasmuch as the missile bay extended considerably ahead of the inlet station, rotation of the missile door created considerable disturbance of the flow entering the inlets. In comparison with the internal missile arrangement, the external missile configurations increased the model lift, drag, and pitching moment. While the diffuser-exit flow distortion and static-pressure fluctuations were not greatly affected, diffuser total-pressure recovery was reduced as much as 0.058 at Mach number 1.9 for one missile configuration. The most detrimental effect of missile-door rotation occurred at the transient door positions, or with the door halfwzy between the missiles-in and -out conditions. At this door position the flow into the inlets was highly asymmetrical. Although the performance of both left and right ducts was generally reduced, the inlet duct on the cavity side of the missile door was most severely penalized, becoming unstable recovery losses and increases in flow distortion. The installation of fuselage fences along the missile bay was only partially effective in reducing these losses.

Piercy, T. G.↗
NASA NTRS1989

A transition detection study at Mach 1.5, 2.0, and 2.5 using a micro-thin hot-film system

A boundary-layer transition detection study was conducted in the NASA Langley unitary plan wind tunnel with an array of microthin hot films on a flat plate at Mach numbers 1.5, 2.0, and 2.5 and Reynolds numbers (1.0-4.5) x 10 to the 6th/ft. Transition locations were obtained online from the variation of normalized rms voltages from an array of hot-film sensors for both natural transition and a grit-induced wedge of turbulence. The effects of Mach number and Reynolds number on the location and length of the transition region for the two types of transition are presented from the online data. Also shown are the unit Reynolds number effects on transition Reynolds number, voltage-versus-time traces, spectra, and the data-acquisition system.

Johnson, Charles B.↗
NASA NTRS1973

Investigation of noise suppression by sonic inlets for turbofan engines. Volume 1: Program summary

Results of a program for sonic inlet technology development are presented. This program includes configuration and mechanical design selection of concepts, aerodynamic design description of the models, and results of test evaluation. Several sonic inlet concepts were tested and compared for aerodynamic and acoustic performance. Results of these comparative evaluations are presented. Near-field measurements were taken inside several of the inlet models. Results of these tests are discussed with respect to the effect of Mach number gradients on noise attenuation and rotor shock wave attenuation, and boundary layer effects on noise propagation. The test facilities and experimental techniques employed are described briefly.

Klujber, F.↗
NASA NTRS1973

Results of an experimental program for the development of sonic inlets for turbofan engines.

Results of a current program for sonic inlet technology development are presented. This program includes configuration and mechanical design selection of concepts, aerodynamic design description of the models, and results of test evaluation. In the test program several sonic inlet concepts were tested and compared for aerodynamic and acoustic performance. Results of these comparative evaluations are presented. Near-field measurements were taken inside the sonic inlet on several inlet models. Results of these tests are discussed with respect to the effect of Mach number gradients on noise attenuation and rotor shock wave attenuation, and boundary layer effects on noise propagation. The test facilities and experimental techniques employed are described briefly.

Klujber, F.↗
NASA NTRS1985

Calculation of water drop trajectories to and about arbitrary three-dimensional lifting and nonlifting bodies in potential airflow

Subsonic, external flow about nonlifting bodies, lifting bodies or combinations of lifting and nonlifting bodies is calculated by a modified version of the Hess lifting code. Trajectory calculations can be performed for any atmospheric conditions and for all water drop sizes, from the smallest cloud droplet to large raindrops. Experimental water drop drag relations are used in the water drop equations of motion and effects of gravity settling are included. Inlet flow can be accommodated, and high Mach number compressibility effects are corrected for approximately. Seven codes are described: (1) a code used to debug and plot body surface description data; (2) a code that processes the body surface data to yield the potential flow field; (3) a code that computes flow velocities at arrays of points in space; (4) a code that computes water drop trajectories from an array of points in space; (5) a code that computes water drop trajectories and fluxes to arbitrary target points; (6) a code that computes water drop trajectories tangent to the body; and (7) a code that produces stereo pair plots which include both the body and trajectories. Accuracy of the calculations is discussed, and trajectory calculation results are compared with prior calculations and with experimental data.

Norment, H. G.↗