Search NASA⌕ Search

SEARCH · Search NASA

Results for “MAGNETRON SPUTTERING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

Influence of RF power on magnetron sputtered AZO films

Al-doped Zinc Oxide (AZO) transparent conducting films are prepared on glass substrate by RF magnetron sputtering under different RF power with a 3 inch diameter target of 2 wt%Al{sub 2}O{sub 3} in zinc oxide. The effect of RF power on the structural, optical and electrical properties of AZO films was investigated by X-ray Diffraction (XRD), Hall measurement and UV-Visible spectrophotometry. The XRD data indicates a preferential c-axis orientation for all the films. All films exhibit high transmittance (<90%) in visible region. Films deposited at 60 W power exhibit lowest resistivity of 5.7 Multiplication-Sign 10{sup -4}{omega}cm. Such low-resistivity and high-transmittance AZO films when prepared using low RF power at room temperature could find important applications in flexible electronics.

36 MATERIALS SCIENCE↗

Thermoelectric properties of epitaxial ScN films deposited by reactive magnetron sputtering onto MgO(001) substrates

Epitaxial ScN(001) thin films were grown on MgO(001) substrates by dc reactive magnetron sputtering. The deposition was performed in an Ar/N{sub 2} atmosphere at 2 Multiplication-Sign 10{sup -3} Torr at a substrate temperature of 850 Degree-Sign C in a high vacuum chamber with a base pressure of 10{sup -8} Torr. In spite of oxygen contamination of 1.6 {+-} 1 at. %, the electrical resistivity, electron mobility, and carrier concentration obtained from a typical film grown under these conditions by room temperature Hall measurements are 0.22 m{Omega} cm, 106 cm{sup 2} V{sup -1} s{sup -1}, and 2.5 Multiplication-Sign 10{sup 20} cm{sup -3}, respectively. These films exhibit remarkable thermoelectric power factors of 3.3-3.5 Multiplication-Sign 10{sup -3} W/mK{sup 2} in the temperature range of 600 K to 840 K. The cross-plane thermal conductivity is 8.3 W/mK at 800 K yielding an estimated ZT of 0.3. Theoretical modeling of the thermoelectric properties of ScN calculated using a mean-free-path of 23 nm at 300 K is in very good agreement with the experiment. These results also demonstrate that further optimization of the power factor of ScN is possible. First-principles density functional theory combined with the site occupancy disorder technique was used to investigate the effect of oxygen contamination on the electronic structure and thermoelectric properties of ScN. The computational results suggest that oxygen atoms in ScN mix uniformly on the N site forming a homogeneous solid solution alloy. Behaving as an n-type donor, oxygen causes a shift of the Fermi level in ScN into the conduction band without altering the band structure and the density of states.

36 MATERIALS SCIENCE↗

Studies on optoelectronic properties of DC reactive magnetron sputtered chromium doped CdO thin films

Cr doped CdO thin films were deposited on glass substrates by DC reactive magnetron sputtering method and subsequently annealed from 200 °C to 500 °C. X-ray diffraction analysis showed that the films exhibit (1 1 1) preferred orientation. The optical transmittance of the films increases from 64% to 88% with increasing annealing temperature. The optical band gap values were found to be decreased from 2.77 to 2.65 eV with the increase of annealing temperature. The decrease in optical band gap energy with increasing annealing temperature can be attributed to improvement in the crystallinity of the films and may also be due to quantum confinement effect. A minimum resistivity of 2.23 × 10{sup −4} Ω.cm and sheet resistance of 6.3 Ω/sq is obtained for Cr doped CdO film annealed at 500 °C.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Optical and local structural study of Gd doped ZrO{sub 2} thin films deposited by RF magnetron sputtering technique

ZrO{sub 2} samples with 0, 7, 9, 11, 13 % Gd doping have been prepared by RF magnetron sputtering deposition technique for solid oxide fuel cell application. The optical properties of the samples have been studied by transmission spectrophotometry and spectroscopic ellipsometry while the local structure surrounding Zr sites has been characterized by extended x-ray absorption fine structure (EXAFS) measurement at Zr K edge with synchrotron radiation. It has been observed that beyond 11% Gd doping, band gap decreases and refractive index increases significantly and also oxygen and Zr coordinations surrounding Zr sites increase which indicates the formation of Gd clustering in ZrO{sub 2} matrix beyond this doping concentration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Synthesis and characterization of DC magnetron sputtered nano structured molybdenum thin films

Molybdenum (Mo) thin films were deposited on corning glass (#7059) substrates using DC magnetron sputtering system. The effect of substrate temperature on the structural, morphology and topological properties have been investigated. Films were characterized by variety of techniques such as low angle x-ray diffraction (low angle XRD), field emission scanning electron microscopy (FE-SEM), atomic force microscopy (AFM). The low angle XRD analysis revealed that the synthesized Mo films are nanocrystalline having cubic crystal structure with (110) preferential orientation. The microstructure of the deposited Mo thin films observed with FE-SEM images indicated that films are homogeneous and uniform with randomly oriented leaf shape morphology. The AFM analysis shows that with increase in substrate temperature the rms roughness of Mo films increases. The obtained results suggest that the synthesized nanostructured Mo thin films have potential application as a back contact material for high efficiency solar cells like CdTe, CIGS, CZTS etc.

36 MATERIALS SCIENCE↗

Spectroscopy analysis of graphene like deposition using DC unbalanced magnetron sputtering on γ‐Al{sub 2}O{sub 3} buffer layer

In this work, graphene-like deposition using DC unbalanced magnetron-sputtering technique on γ‐Al{sub 2}O{sub 3} layer at low temperature has been systematically studied. The γ‐Al{sub 2}O{sub 3} was growth on silicon substrate using thermal evaporation of Al wire and continuing with dry oxidation of Al at 550 °C. Sputtering process were carried out using Fe-doped carbon pellet as a target by maintain the chamber pressure of 4.6×10{sup −2} Torr at substrate temperature of 300 °C for time deposition range of 1 to 4 hours. The quality of Al{sub 2}O{sub 3} on Si(100) and the characteristic of carbon thin film on γ‐Al{sub 2}O{sub 3} were analized by mean XRD, opctical microscopy, EDAX, FTIR, and Raman spectra. XRD and optical microscopy analysis shows that Al{sub 2}O{sub 3} film is growth uniformly on Si substrate and forming the γ phase of Al{sub 2}O{sub 3}. Raman and FTIR spectra confirm the formation of graphene like carbon layer on Al{sub 2}O{sub 3}. Additionally, thermal annealing for some sample series have been performed to study their structural stability. The change of atomic structure due to thermal annealing were analized by XRD spectra. The quality and the number of graphene layers are investigated by using Raman spectra peaks analysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Synthesis of copper nitride films doped with Fe, Co, or Ni by reactive magnetron sputtering

Copper nitride (Cu{sub 3}N) and Fe-, Co-, and Ni-doped Cu{sub 3}N films were prepared by reactive magnetron sputtering. The films were deposited on silicon substrates at room temperature using pure Cu target and metal chips. The molar ratio of Cu to N atoms in the as-prepared Cu{sub 3}N film was 2.7:1, which is comparable with the stoichiometry ratio 3:1. X-ray diffraction measurements showed that the films were composed of Cu{sub 3}N crystallites with anti-ReO{sub 3} structure and adopted different preferred orientations. The reflectance of the four samples decreased in the wavelength range of 400–830 nm, but increased rapidly within wavelength range of 830–1200 nm. Compared with the Cu{sub 3}N films, the resistivity of the doped Cu{sub 3}N films decreased by three orders of magnitude. These changes have great application potential in optical and electrical devices based on Cu{sub 3}N films.

36 MATERIALS SCIENCE↗

Hydroxyapatite coating on biodegradable AZ31 and Mg-Ca alloys prepared by RF-magnetron sputtering

A thin film of hydroxyapatite (HA) was deposited on AZ31 and Mg-Ca alloys by using radio frequency (RF) magnetron sputtering. The thickness of the HA coating was determined to be 750 nm. The phase composition, microstructure, and surface morphology of the HA coatings were investigated using X-ray diffraction and scanning electron microscopy. In vitro degradation behaviour of the HA coated alloys was evaluated in simulated body fluid (SBF) and 3.5wt.% NaCl solution using electrochemical method. The coatings homogeneously covered the entire surface of the substrates. The coating structure corresponded to a nanostructured HA. The ultrathin coating significantly improved the degradation resistance of the alloy. Nanocrystalline HA coating significantly improved the corrosion resistance of the Mg-Ca and AZ31 magnesium alloys. The polarization resistance (Rp) of the coated Mg-Ca alloy was more than two-order of magnitude higher and the corrosion current density I{sub corr} reduced by ∼ 98% as compared to the base alloy.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of Ti–B–C–N–Si nanocomposite films deposited by unbalanced magnetron sputtering

Quinary Ti–B–C–N–Si nanocomposite thin films were deposited on AISI 304 stainless steel substrates by d.c. unbalanced magnetron sputtering from a TiB{sub 2}–TiC compound target and a pure Si target. The relationship between microstructure and mechanical properties of the films was investigated in terms of the nanosized crystallites/amorphous system. The synthesized Ti–B–C–N–Si films were characterized using x-ray diffraction, x-ray photoelectron spectroscopy, atomic force microscopy, and high resolution transmission electron microscopy. The results showed that the Ti–B–C–N–Si films were nanocomposites composed of nanosized TiB{sub 2}, TiC, and TiSi{sub 2} crystallites (2-3 nm in size) embedded in an amorphous matrix. The addition of Si to the Ti–B–C–N film led to precipitation of nanosized crystalline TiSi{sub 2} and percolation of amorphous SiC phases. The Ti–B–C–N–Si films with up to 7 at. % Si content presented high hardness (≥35 GPa), H/E (≥0.0095), and W{sub e} (>50%) with compressive residual stress (∼0.5 GPa). A systematic investigation on the microstructure and mechanical properties of Ti–B–C–N–Si films containing different Si contents is reported.

36 MATERIALS SCIENCE↗

Deposition of very thick Mo/Al multilayer films using magnetron sputtering

To understand materials at extreme conditions dynamic ramp compression techniques/experiments are critical, and gradient density impactors (GDIs) have the potential to enable high quality experiments. Very thick (i.e., hundreds of μm thick) multilayer films consisting of high z/low z layers with a gradient in z through the stack can serve as a GDI. Surprisingly while there is a large amount of literature on the topic of multilayer films, there is an absence of literature on very thick multilayer films. A number of multilayer film systems deposited by dc magnetron sputtering were evaluated as potential candidates, including Cu/Al, Ta/Al, and Mo/Al. The Mo/Al multilayer system was observed to be the most promising candidate and is the primary focus of this paper. Mo/Al multilayer films up to ∼400 μm thick with reasonable thickness uniformity were deposited.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Comprehensive study of the p-type conductivity formation in radio frequency magnetron sputtered arsenic-doped ZnO film

Arsenic doped ZnO and ZnMgO films were deposited on SiO{sub 2} using radio frequency magnetron sputtering and ZnO-Zn{sub 3}As{sub 2} and ZnO-Zn{sub 3}As{sub 2}-MgO targets, respectively. It was found that thermal activation is required to activate the formation of p-type conductivity. Hall measurements showed that p-type films with a hole concentration of {approx}10{sup 17} cm{sup -3} and mobility of {approx}8 cm{sup 2} V{sup -1} s{sup -1} were obtained at substrate temperatures of 400-500 deg. C The shallow acceptor formation mechanism was investigated using x-ray photoelectron spectroscopy, positron annihilation, low temperature photoluminescence, and nuclear reaction analysis. The authors suggest that the thermal annealing activates the formation of the As{sub Zn}-2V{sub Zn} shallow acceptor complex and removes the compensating hydrogen center.

36 MATERIALS SCIENCE↗

Deposition and characterization of zirconium nitride (ZrN) thin films by reactive magnetron sputtering with linear gas ion source and bias voltage

Zirconium nitride thin films have been prepared on stainless steel substrate (304L grade) by reactive cylindrical magnetron sputtering method with Gas Ion Source (GIS) and bias voltage using optimized coating parameters. The structure and surface morphologies of the ZrN films were characterized using X-ray diffraction, atomic microscopy and scanning electron microscopy. The adhesion property of ZrN thin film has been increased due to the GIS. The coating exhibits better adhesion strength up to 10 N whereas the ZrN thin film with bias voltage exhibits adhesion up to 500 mN.

36 MATERIALS SCIENCE↗

High quality boron carbon nitride/ZnO-nanorods p-n heterojunctions based on magnetron sputtered boron carbon nitride films

Boron carbon nitride (BCN) films were synthesized on Si (100) and fused silica substrates by radio-frequency magnetron sputtering from a B{sub 4}C target in an Ar/N{sub 2} gas mixture. The BCN films were amorphous, and they exhibited an optical band gap of ∼1.0 eV and p-type conductivity. The BCN films were over-coated with ZnO nanorod arrays using hydrothermal synthesis to form BCN/ZnO-nanorods p-n heterojunctions, exhibiting a rectification ratio of 1500 at bias voltages of ±5 V.

36 MATERIALS SCIENCE↗

Effects of growth rate and dynamic substrate tilt on properties of Au-Ta alloy films deposited by high-power impulse magnetron sputtering

Gold-tantalum (Au—Ta) alloys are promising for next-generation hohlraums for magnetically-assisted indirect-drive inertial confinement fusion. Hohlraum fabrication involves sputter deposition of ultrathick coatings on sphero-cylindrical substrates. The control of physical properties of such coatings remains a challenge. Here, in this work, we systematically study effects of the growth rate and dynamic substrate tilt on properties of AuTa 4 films deposited onto rotating planar substrates mounted at different tilt angles to mimic different regions of the sphero-cylindrical surface of a hohlraum. We use high-power impulse magnetron sputtering (HiPIMS) in the constant charge per pulse mode with a pulse duration of 100 μs, a charge per pulse of 190 μC, a peak target current of about 3 A, and the pulse frequency varied in the range of 400–1400 Hz. The Langmuir probe, mass-resolved ion energy spectrometry, and optical emission spectroscopy are used to monitor plasma discharge characteristics in order to isolate and study effects of the growth rate. The deposition rate and the ballistics and energetics of depositing species are estimated by Monte Carlo simulations. Results show that the film microstructure, crystallographic phase, residual stress, and electrical resistivity strongly depend on both the deposition rate and substrate tilt, highlighting their critical role in tailoring properties of Au—Ta films during hohlraum fabrication.

36 MATERIALS SCIENCE↗

Photocatalytic activity of anatase titanium dioxide nanostructures prepared by reactive magnetron sputtering technique

In this work, nanostructured titanium dioxide (TiO{sub 2}) photocatalysts with high optical and structural homogeneity were successfully synthesized by dc reactive magnetron sputtering technique. The TiO{sub 2} thin films were produced with high structural homogeneity without any heat treatment. Analysis of the X-ray diffraction patterns and UV–visible spectroscopy gave an indication that the structure of prepared films is anatase with energy band gap of 3.23 eV. The Fourier-transform infrared spectroscopy has confirmed the formation of Ti–O bond. The average size of TiO{sub 2} particles in the deposited films was ranging in 5–7 nm. These nanostructures are very applicable as photocatalysts as their photocatalytic activity was determined from the degradation rate with UV irradiation time as the first order reaction rate constant was determined to be 2.4 × 10{sup −3} min{sup −1}.

36 MATERIALS SCIENCE↗

Physical properties of RF magnetron sputtered GaN/n-Si thin film: impacts of RF power

GaN thin film was successfully produced on n-Si(100) substrate by RF magnetron sputter under different RF power. Experimental measurement techniques such as UV/Vis spectroscopy, field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), atomic force microscopy (AFM), and Micro-Raman Spectroscopy were used to research effects of Radio Frequency power on physical properties of produced thin film. It has been found that produced thin film was polycrystalline structure with (100) and (110) planes of hexagonal GaN from X-ray diffraction measurement result. It also proved that increasing RF power gives rise to deterioration in crystal quality of GaN thin film. Reason of this deterioration was discussed. It has been achieved that increasing RF power has resulted in decreasing optical band gap energy of GaN thin film. Reasons for these changes in optical band gap energy were explained. It was seen that some thin films were grown as layer-plus-island mode (Stranski–Krastanov growth mode) and others were grown as layer-by-layer growth mode (Frank van der Merwe mode) from AFM analysis. It has been found that increasing RF power has resulted in improvement of surface morphology of thin film from field emission scanning electron microscopy analysis. However, reaching RF power to 125 W leads to start to deteriorate of surface of GaN thin film. The reasons for this have been discussed. E{sub 1}(TO) transverse optical phonon mode of hexagonal GaN with different intensity was detected from Micro-Raman Spectroscopy measurement. The reasons for this difference have been discussed. It was concluded that RF power has played a significant role in growing high quality GaN thin film. Morphological, structural, and optical properties of GaN thin film were enhanced by controlling RF power, making them a potential candidate for LED, solar cell, diode application.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Preparation and Oxidation Performance of a NiCoCrAlYSiHf + NiAl Composite Coating Deposited by Arc Ion Plating and Magnetron Sputtering Techniques

A NiCoCrAlYSiHf+NiAl composite coating was deposited onto a second-generation single-crystal superalloy René N5 by methods of arc ion plating and magnetron sputtering. After vacuum annealing, the composite coating exhibited a gradient distribution of elements, in which Al was enriched in outer layer and Cr was enriched in inner layer. Compared with conventional NiCoCrAlYSiHf and β-NiAl coatings, the composite coating was evaluated in isothermal and cyclic oxidation tests at 1100 °C in ambient air. The results showed that the oxidation rate of the composite coating was lower than that of NiCoCrAlYSiHf coating. Meanwhile, the extent of interdiffusion between coating and substrate in the composite coating was slighter compared with that in the β-NiAl coating. Microstructure evolutions of the composite coating after annealing and further oxidation test are investigated.

36 MATERIALS SCIENCE↗

Structural and electrical characteristics of high quality (100) orientated-Zn{sub 3}N{sub 2} thin films grown by radio-frequency magnetron sputtering

We report on highly crystalline zinc nitride (Zn{sub 3}N{sub 2}) thin films which were grown by rf magnetron sputtering on quartz substrates. The substrate temperature during growth is found to strongly affect the crystal quality of the thin films. The chemical bonding states were determined by x-ray photoelectron spectroscopy. Large chemical shifts in core-level N 1s peaks with binding energy of 396.4 eV were observed as compared to N 1s of free amine (398.8 eV), indicating Zn-N bond formation. Two N 1s states were found: one is N{sub 1} formed by Zn-N bonds and another is (N{sub 2}) produced by substitution of N molecules at N ion sites, which leads to larger lattice constants, consistent with x-ray diffraction results. Temperature-dependent Hall effect measurements of our Zn{sub 3}N{sub 2} films exhibited distinct conduction mechanisms at specific different temperature ranges.

36 MATERIALS SCIENCE↗