Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mechanical Design”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2012

The Transport of Mass, Energy, and Entropy in Cryogenic Support Struts for Engineering Design

Engineers working to understand and reduce cryogenic boil-off must solve a. variety of transport problems. An important class of nonlinear problems involves the thermal and mechanical design of cryogenic struts. These classic problems are scattered about the literature and typically require too many resources to obtain. So, to save time for practicing engineers, the author presents this essay. Herein, a variety of new, old, and revisited analytical and finite difference solutions of the thermal problem are covered in this essay, along with commentary on approach and assumptions, This includes a few thermal radiation and conduction combined mode solution with a discussion on insulation, optimum emissivity, and geometrical phenomenon. Solutions to cooling and heat interception problems are also presented, including a discussion of the entropy generation. And the literature on the combined mechanical and thermal design of cryogenic support struts is reviewed with an introduction to the associated numerical methods.

Elchert, J. P.↗
NASA NTRS1977

Design definition of a mechanical capacitor

A design study and analyses of a 10 kW-hr, 15 kW mechanical capacitor system was studied. It was determined that magnetically supported wheels constructed of advanced composites have the potential for high energy density and high power density. Structural concepts are analyzed that yield the highest energy density of any structural design yet reported. Particular attention was paid to the problem of 'friction' caused by magnetic and I to the second power R losses in the suspension and motor-generator subsystems, and low design friction levels have been achieved. The potentially long shelf life of this system, and the absence of wearing parts, provide superior performance over conventional flywheels supported with mechanical bearings. Costs and economies of energy storage wheels were reviewed briefly.

Michaelis, T. D.↗
NASA NTRS1994

Pip pin reliability and design

Pip pins are used in many engineering applications. Of particular interest to the aerospace industry is their use in various mechanism designs. Many payloads that fly aboard our nation's Space Shuttle have at least one actuated mechanism. Often these mechanisms incorporate pip pins in their design in order to fasten interfacing parts or joints. Pip pins are most often used when an astronaut will have a direct interface with the mechanism. This interfacing can be done during Space Shuttle mission EVA's (ExtraVehicular Activity). The main reason for incorporating pip pins is convenience and their ability to provide a quick release for interfacing parts. However, there are some issues that must be taken into account when using them in a design. These issues include documented failures and quality control problems when using substandard pip pins. A history of pip pins as they relate to the aerospace industry as well as general design features is discussed.

Skyles, Lane P.↗
NASA NTRS1991

Guideline requirements for serviceable spacecraft grasping/berthing/docking interfaces based on simulations and flight experience (survey paper)

As space vehicles and structures become larger and more complex, the development of systems to assist humans in assembling, operating, maintaining, and performing space rescue or retrieval of these vehicles and structures becomes increasingly important. With the diversity of international spacecraft, both manned and unmanned, planned to be in orbit in the future, a set of guidelines for berthing and docking subsystems is mandatory if servicing, resupply, and retrieval is to become practical on an international level. Successful interaction between these space systems and ground and/or space-based humans requires standardized and effective operational interface designs, particularly with respect to space grasping/berthing/docking interface mechanisms. This paper defines the spacecraft mechanical interfaces necessary to create a standard dynamic envelope for joining two free-flying spacecraft in a 'hard' berth or dock with each other in space. A review was made of past space flights and dynamics simulations dating back to 1962 to obtain necessary parameters and their values for successful manually controlled and autonomous spacecraft docking/berthing. The various spacecraft docking/berthing mechanisms and concepts are illustrated along with their dynamic capture and impact tolerances including maximum contact velocity along the approach axis and in the y-z plane; capture linear misalignment tolerances; and maximum capture roll, pitch, and yaw angles. From this data sets of recommended guidelines parameters were developed for autonomous and manual impact docking tolerances, non-impact grasping/berthing tolerances (end effectors), berthing contact conditions, and alignment tolerances after rigidizing. Also, detailed requirements were developed for mechanical design interface features, as well as latching, unlatching, and separation tolerances. This data was drafted in the form of a proposed ANSI Standard guideline, reviewed, and added to by members of the committee representing several spacecraft manufacturers, NASA, and the USAF, and a consensus was reached.

Thompson, Allen B.↗
NASA NTRS2002

Investigation of Space Based Solid State Coherent Lidar

This report describes the work performed over the period of October 1, 1997 through March 31, 2001. Under this contract, UAH/CAO participated in defining and designing the SPAce Readiness Coherent Lidar Experiment (SPARCLE) mission, and developed the instrument's optical subsystem. This work was performed in collaborative fashion with NASA/MSFC engineers at both UAH/CAO and NASA/MSFC facilities. Earlier work by the UAH/CAO had produced a preliminary top-level system design for the Shuttle lidar instrument meeting the proposed mission performance requirements and the Space Shuttle Hitchhiker canister volume constraints. The UAH/CAO system design efforts had concentrated on the optical and mechanical designs of the instrument. The instrument electronics were also addressed, and the major electronic components and their interfaces defined. The instrument design concept was mainly based on the state of the transmitter and local oscillator laser development at NASA Langley Research Center and Jet Propulsion Laboratory, and utilized several lidar-related technologies that were either developed or evaluated by the NASA/MSFC and UAH/CAO scientists. UAH/CAO has developed a comprehensive coherent lidar numerical model capable of analyzing the performance of different instrument and mission concepts. This model uses the instrument configuration, atmospheric conditions and current velocity estimation theory to provide prediction of instrument performance during different phases of operation. This model can also optimize the design parameters of the instrument.

Amzajerdian, Farzin↗
NASA NTRS2004

Deployment Mechanism for the Space Technology 5 Micro Satellite

Space Technology 5 (ST5) is a technology mission that will send three spin-stabilized, 25-kg satellites into a highly elliptical Earth orbit. Each of these satellites must be deployed separately from the same launch vehicle with a spin rate of 3.4 rads (32.4 rpm). Because of the satellite's small size and the requirement to achieve its mission spin rate on deploy, typical spin table, pyrotechnic deployment devices or spin up thrusters could not be used. Instead, this new mechanism design employs a "Frisbee" spin up strategy with a shape memory alloy actuated Pinpuller to deploy each satellite. The mechanism has undergone several design and test iterations and has been successfully qualified for flight.

Rossoni, Peter↗
NASA NTRS2004

Deployment Mechanism for the Space Technology 5 Micro Satellite

Space Technology 5 (ST5) is a technology mission that will send three spin-stabilized, 25-kg satellites into a highly elliptical Earth orbit. Each of these satellites must be deployed separately from the same launch vehicle with a spin rate of 3.4 rad/s (32.4 rpm). Because of the satellite's small size and the requirement to achieve its mission spin rate on deploy, typical spin table, pyrotechnic deployment devices or spin up thrusters could not be used. Instead, this new mechanism design employs a 'Frisbee' spin up strategy with a shape memory alloy actuated Pinpuller to deploy each satellite. The mechanism has undergone several design and test iterations and has been successfully qualified for flight.

Rossoni, Peter↗
NASA NTRS1984

Structural design of a vertical antenna boresight 18.3 by 18.3-m planar near-field antenna measurement system

A large very precise near-field planar scanner was proposed for NASA Lewis Research Center. This scanner would permit near-field measurements over a horizontal scan plane measuring 18.3 m by 18.3 m. Large aperture antennas mounted with antenna boresight vertical could be tested up to 60 GHz. When such a large near field scanner is used for pattern testing, the antenna or antenna system under test does not have to be moved. Hence, such antennas and antenna systems can be positioned and supported to simulate configuration in zero g. Thus, very large and heavy machinery that would be needed to accurately move the antennas are avoided. A preliminary investigation was undertaken to address the mechanical design of such a challenging near-field antenna scanner. The configuration, structural design and results of a parametric NASTRAN structural optimization analysis are contained. Further, the resulting design was dynamically analyzed in order to provide resonant frequency information to the scanner mechanical drive system designers. If other large near field scanners of comparable dimensions are to be constructed, the information can be used for design optimization of these also.

Sharp, G. R.↗
NASA NTRS1973

Space shuttle main engine controller assembly, phase C-D

System design and system analysis and simulation are slightly behind schedule, while design verification testing has improved. Input/output circuit design has improved, but digital computer unit (DCU) and mechanical design continue to lag. Part procurement was impacted by delays in printed circuit board, assembly drawing releases. These are the result of problems in generating suitable printed circuit artwork for the very complex and high density multilayer boards.

Source record↗
NASA NTRS1990

Examples of finite element mesh generation using SDRC IDEAS

IDEAS (Integrated Design Engineering Analysis Software) offers a comprehensive package for mechanical design engineers. Due to its multifaceted capabilities, however, it can be manipulated to serve the needs of electrical engineers, also. IDEAS can be used to perform the following tasks: system modeling, system assembly, kinematics, finite element pre/post processing, finite element solution, system dynamics, drafting, test data analysis, and project relational database.

Zapp, John↗
NASA NTRS1991

Cryogenic mechanisms for scanning and interchange of the Fabry-Perot interferometers in the ISO long wavelength spectrometer

The Infrared Space Observatory (ISO) is an ESA cornerstone mission for infrared astronomy. Schedules for launch in 1993, its four scientific instruments will provide unprecedented sensitivity and spectral resolution at wavelengths which are inaccessible using ground-based techniques. One of these, the Long Wavelength Spectrometer (LWS), will operate in the 45 to 180 micron region (Emery et. al., 1985) and features two Fabry-Perot interferometers mounted on an interchange mechanism. The entire payload module of the spacecraft, comprising the 60 cm telescope and the four focal plane instruments, is maintained at 2 to 4 K by an onboard supply of liquid helium. The mechanical design and testing of the cryogenic interferometer and interchange mechanisms are described.

Davis, G. R.↗
NASA NTRSDate not supplied

NASA Lunabotics Robotic Mining Competition 10th Anniversary (2010-2019): Taxonomy and Technology Review

Space Mining for resources such as water ice, and regolith, which contain many elements in the form of metals, minerals, volatiles and other compounds, is a necessary step for In-Situ Space Resource Utilization (ISRU). One of the primary goals is to extract propellants from the regolith and water ice, such as oxygen and hydrogen which could then be used for in-space transportation. In addition, the space mining system can be used for various construction tasks that can benefit human and robotic exploration as well as scientific investigations based on excavated exposed topography, such as the side walls of trenches. The National Aeronautics & Space Administration (NASA) "Lunabotics" Robotic Mining Competition (RMC) is a university-level competition designed to engage and retain students in science, technology, engineering and mathematics (STEM). NASA has directly benefited from the competition by encouraging the development of innovative lunar excavation concepts from universities which has resulted in clever ideas and solutions which could be applied to an actual lunar excavation device or payload. The challenge is for students to design and build a remote controlled or autonomous excavator, called a "lunabot", which can collect and deposit a minimum of 10 kilograms of lunar simulant within 15 minutes. In recent years the goal has been changed to excavate a minimum of 1 kg of simulated icy regolith which is found under an overburden of regolith simulant. The complexities of the challenge include the abrasive characteristics of the lunar regolith simulant, the weight and size limitations of the lunabot, and the ability to control the lunabot from a remote-control center or operate it autonomously. This paper will present the results of the ten Lunabotics Robotic Mining Competitions held between May 2010 and May 2019. Each year over 50 university teams have attended, resulting in over 500 lunabot designs and subsequent prototypes. Over 6,000 university students have been part of the on-site competition at KSC. Even more students and the public were engaged via internet broadcasting and social networking media. The various designs have been cataloged and categorized here to provide information to future Lunabotics RMC mining robot designers and competitors. Categories will focus on both the mechanical design as well as the autonomy architecture/design. It is also expected to be of value for actual future space missions, as knowledge is gained from testing many innovative prototypes in simulated lunar regolith. A taxonomy of robotic excavator designs has been presented. In addition, the paper will discuss changes in learning paradigms occurring in the current generation of students, and how this competition leverages those changes to challenge students to develop skills in graduate level concepts and apply them. Examples of how this translates to hiring opportunities for commercial sponsors has also been discussed.

Robert P Mueller↗
NASA NTRS1971

Meeting the challenge of a 50000-hour-life-time requirement

Space mission requirements for the 70's have established a 50,000-hour-lifetime challenge for the mechanisms designer. This challenge may be met by two approaches: (1) development of new materials for wear-prone elements, and (2) design innovation of new electromechanical devices that do not include mechanical wear-prone components. Present state-of-the-art materials require restricted operation regarding load, speed, and power for gears, bearings, and brush-slipring components. These restrictions are discussed, and methods of improvement are suggested. The design-innovations approach is discussed and is illustrated by the design of an experimental magnetically suspended motor.

Vest, C. E.↗
NASA NTRS2007

Optomechanical Design and Analysis Considerations on the Lunar Orbiter Laser Altimeter

This paper presents the mechanical design and analysis work completed on the Lunar Orbiter Laser Altimeter (LOLA). LOLA is one of six instruments on the Lunar Reconnaissance Orbiter (LRO), scheduled to launch in 2008. LOLA's main objective is to produce a high-resolution global lunar topographic model to aid in safe landings and enhance surface mobility in future exploration missions. LOLA will also look for evidence of ice water in the permanently shadowed regions around the lunar poles. Beryllium was chosen as the primary material for the LOLA Optical Transmitter Assembly to take advantage of the material's low mass density for light weight optical instrument design and for CTE matching of the refractive optical components. In addition, the thermal conductivity and specific heat of beryllium minimizes thermal gradients and thermal excursions. Special consideration must be made for the planning and preparation to fabricate beryllium components, as well as the preparation and cleaning of the components for gold plating. Assembly challenges include handling, precision cleaning and integration and testing. Structural analysis considerations include following General Environmental Verification Specification (GEVS) guidelines for GSFC payloads. The GEVS random environment for LOLA has an acceptance level of 10.0 Grms, which was analyzed for higher frequency transients. The low frequency transients were analyzed using a Mass Acceleration Curve to obtain an equivalent static loading. In addition, Structural-Thermal-Optical analysis, commonly referred to as STOP analysis, was completed to predict optical performance under the instrument's operational thermal environment. This included stress and distortion analysis on the receiver telescope lens.

Schmidt. Stephen↗
NASA NTRS1989

Computer Aided Design of Computer Generated Holograms for electron beam fabrication

Computer Aided Design (CAD) systems that have been developed for electrical and mechanical design tasks are also effective tools for the process of designing Computer Generated Holograms (CGHs), particularly when these holograms are to be fabricated using electron beam lithography. CAD workstations provide efficient and convenient means of computing, storing, displaying, and preparing for fabrication many of the features that are common to CGH designs. Experience gained in the process of designing CGHs with various types of encoding methods is presented. Suggestions are made so that future workstations may further accommodate the CGH design process.

Urquhart, Kristopher S.↗