2m interference filters for the ultraviolet.
Fabry-Perot narrow band transmission filter using multilayer containing semitransmitting aluminum films
Maier, R. L.↗
SEARCH · Search NASA
Results for “Multilayer films”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Rocket flight of a multilayer coated high-density EUV toroidal grating
A multilayer coated high density toroidal grating was flown on a sounding rocket experiment in the Solar EUV Rocket Telescope and Spectrograph (SERTS) instrument. To our knowledge this is the first space flight of a multilayer coated grating. Pre-flight performance evaluation showed that the application of a 10-layer Ir/Si multilayer coating to the 3600 l/mm blazed toroidal replica grating produced a factor of 9 enhancement in peak efficiency near the design wavelength around 30 nm in first order over the standard gold coating, with a measured EUV efficiency that peaked at 3.3 percent. In addition, the grating's spectral resolution of better than 5000 was maintained. The region of enhanced grating efficiency due to the multilayer coating is clearly evident in the flight data. Within the bandpass of the multilayer coating, the recorded film densities were roughly equivalent to those obtained with a factor of six longer exposure on the previous flight of the SERTS instrument.
Keski-Kuha, Ritva A. M.↗
Nondestructive Detection of Cracks in Ceramics Using Vicinal Illumination
Cracks and other defects in ceramic materials can be difficult or impossible to examine and photograph due to the extreme lack of contrast. A method for inspecting translucent ceramics using scattered light, also known as vicinal illumination, will be described. This method has been known in the ceramics industry for quite some time, but is not well known in the testing and failure analysis community. Electronics applications include substrates, packages, multilayer capacitors, and thin film resistors. Ceramic materials are used in electronic applications as microcircuit packages and substrates which carry signals and power between microcircuits. Fine cracks in ceramic materials can result in mechanical failures, electrical failures, and loss of hermeticity. Often, fine cracks are difficult or impossible to detect using standard nondestructive inspection techniques such as visual inspection, ultrasonic inspection, or vapor crack detection. Dye penetrant inspection is usually effective, but contaminates the part, which is unacceptable for space flight hardware. One effective nondestructive inspection method of detecting cracks involves examining the way in which light scatters through the ceramic material when viewed with a standard bright field reflected light microscope. This method, termed vicinal illumination, has been used for detecting cracks during failure analyses of several part types, and screening of space flight hardware. The technique has proven effective on several different types of ceramic materials as well. A related method for use with dark field equipment has also been used to successfully locate otherwise invisible cracks.
Hull, Scott M.↗
Low Energy Ionizing Radiation and Plasma Contributions to Radiation Dose in Materials at Sun-Earth Lagrange Points
- High energy radiation environments responsible for radiation damage to thick materials are well characterized and modeled: - Galactic cosmic rays — Badhwar-O’Neil 2020, CREME96, Nymmik - Solar particle events — Emission of Solar Protons, SAPPHIRE, JPL, King 1972 - Trapped radiation belts — AE8/AP8, AE9/AP9/IRENE - Low energy radiation environments responsible for radiation damage to thin materials relevant to Lagrange points and interplanetary missions have not been treated as comprehensively to date: - Solar wind - Magnetosheath - Magnetotail - Concern to spacecraft design and operations is radiation damage to surfaces and thin materials with mission critical applications on exterior of spacecraft - Applications: thermal control coatings, sunshields, multilayer insulation, optical thin film coatings, solar sails, thermo-optical properties of space exposed materials - Damage processes: radiation degradation (total dose), light ion sputtering, proton blistering of soft metals, modification of optical properties (α/ε), modification of charging properties (SEY, surface conductivity)
Joseph I. Minow↗
Properties of multilayer filters Interim report, Mar. 1 - Aug. 31, 1965
Theoretical properties of band pass filter consisting of single metal layer surrounded by dielectric films
MULTILAYER STRUCTURE↗
Polyhydroxybutyrate laminated trilayer films with enhanced barrier and mechanical properties for active food packaging
Polysaccharides such as starch and chitosan have been explored for sustainable food packaging films. However, their inherent hydrophilicity and brittleness cause poor water vapor barrier performance and limited mechanical properties. To address these issues, starch was first functionalized with acetoacetate groups and subsequently blended with chitosan. Dynamic cross-linking occurred between the acetoacetate groups and the primary amine groups of chitosan, forming vinylogous urethane linkages that reduced the water solubility of the films while preserving high mechanical strength. With 30 wt% of glycerol as a plasticizer, the resulting films showed a tensile strength of up to 24.68 MPa and an elongation at break of up to 83.96%. To improve the barrier properties, poly(3-hydroxybutyrate) (PHB), plasticized with 5-15 wt% epoxidized vegetable oil, was laminated on top of the chitosan/modified starch films, resulting in a significantly reduced water vapor transmission rate (WVTR) of 66%. Additional components, such as food colors like β-carotene were incorporated into this layer to make UV-protective films. A third layer of PHB without active additives was then coated to further reduce WVTR by 99%. Therefore, this multilayer lamination strategy effectively enhanced the barrier and mechanical properties of the polysaccharide-based packaging films.
Active packaging↗
High laser fluence ITO coatings utilizing a Fabry-Perot thin film filter to reduce effective absorption
Laser-induced damage threshold of transparent conductors, such as Indium Tin Oxide (ITO), is limited by their high optical absorption due to free carriers. However, the effective absorption of a transparent conductor thin film can be reduced by an order of magnitude, without changing the electrical characteristics of the film, when placed in a low electric field section of a multilayer coating. A Fabry-Perot thin film interference filter has both high transmittance and low electric field positions, so it is an ideal thin film structure for this application. Although Fabry-Perot interference filters are not known as particularly high laser-induced damage resistant coatings due to their resonant characteristics, a laser-induced damage threshold (LIDT) improvement of up to 8× was observed with this technique compared to single layer ITO coatings fabricated using either radio frequency magnetron sputtering or electron-beam deposition. Additionally, an approximately 4× LIDT improvement for a Fabry-Perot interference filter has been observed by the addition of ITO into the multilayer structure.
47 OTHER INSTRUMENTATION↗
Fabrication of Nb3Sn by Magnetron Sputtering for Superconducting Radiofrequency Application
Particle accelerators are considered as an important device that has wide applications in cancer treatment, sterilizing waste, preserving foods, ion implantation in semiconductor industry, and in production of isotopes for medical applications. Superconducting radiofrequency (SRF) cavities are the building blocks of a linear particle accelerator. Current particle accelerators use niobium (Nb) superconductors as the sheet material to fabricate a single SRF cavity for particle acceleration. With better superconducting properties (critical temperature Tc ~ 18.3 K, superheating field Hsh~ 400 mT), Nb3Sn is considered a potential candidate in SRF technology. Magnetron sputtering is a promising deposition method to fabricate Nb3Sn thin films inside SRF cavities. Superconducting Nb3Sn films were fabricated on Nb and sapphire substrates by magnetron sputtering from a single stoichiometric Nb3Sn target, by multilayer sputtering of Nb and Sn followed by annealing, and by co-sputtering of Nb and Sn followed by annealing. The variation of morphological and superconducting properties was investigated for different substrate temperatures, annealing temperatures, annealing durations, and thicknesses. The film properties were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM), atomic force microscopy (AFM), and energy dispersive X-ray spectroscopy (EDS). The films had crystalline Nb3Sn structure without any presence of poor superconducting Nb6Sn5 and NbSn2 phases. The highest Tc of the films fabricated from the stoichiometric target, multilayer sputtering and co-sputtering were 17.44, 17.93, and 17.66 K respectively. Finally, a cylindrical sputter coater with two identical magnetrons was designed and commissioned to fabricate Nb3Sn films inside a 2.6 GHz SRF cavity. The magnetrons were installed facing opposite to each other in a custom designed vacuum chamber and multilayers of Nb and Sn films on 1 cm2 Nb substrates replicating the beam tubes and equator locations of the cavity and the coated multilayered films were annealed at 950 °C for 3 h. The XRD of the as?deposited and annealed films confirmed the formation of Nb3Sn after the annealing. The dissertation discusses the fabrication process, characterized results of the fabricated films, the design of the cylindrical sputter coater and the preliminary data obtained from the sputter coater.
Sayeed, Md Nizam↗
Control of work functions of nanophotonic components
Work function is an essential material’s property playing important roles in electronics, photovoltaics, and more recently, in nanophotonics. We have studied effects of organic, and inorganic dielectric materials on work functions of Au films in single layered, and multilayered structures. We found that measured work function of metallic surfaces can be affected by dielectric materials situated 10–100 nm away from the metallic surface. We have found that, (i) the glass underneath ~ 50 nm gold slab reduces the work function of gold, (ii) Rh590:PMMA increases the work function of a gold film deposited on top of the polymer, and (iii) reduces it if Rh590:PMMA is deposited on top of Au. (iv) With increase of the Rh590 concentration in PMMA, n, the work function first decreases (at n < 64 g/l), and then increases (at n > 64 g/l). (v) The work function of a Fabry–Perot cavity or an MIM waveguide is almost the same as that of single Au films of comparable thickness. The experimental results can be qualitatively explained in terms of a simple model taking into account adhesion of charged molecules to a metallic surface, and formation of a double layer of charges accelerating or decelerating electrons exiting the metal and decreasing or increasing the work function.
36 MATERIALS SCIENCE↗
Helium Bubbles and Blistering in a Nanolayered Metal/Hydride Composite
Helium is insoluble in most metals and precipitates out to form nanoscale bubbles when the concentration is greater than 1 at.%, which can alter the material properties. Introducing controlled defects such as multilayer interfaces may offer some level of helium bubble management. This study investigates the effects of multilayered composites on helium behavior in ion-implanted, multilayered ErD 2 /Mo thin film composites. Following in-situ and ex-situ helium implantation, scanning and transmission electron microscopy showed the development of spherical helium bubbles within the matrix, but primarily at the layer interfaces. Bubble linkage and surface blistering is observed after high fluence ex-situ helium implantation. These results show the ability of metallic multilayers to alter helium bubble distributions even in the presence of a hydride layer, increasing the lifetime of materials in helium environments.
36 MATERIALS SCIENCE↗
Reaction of amorphous Ni-W and Ni-N-W films with substrate silicon
Wiley et al. (1982) have studied sputtered amorphous films of Nb-Ni, Mo-Ni, Si-W, and Si-Mo. Kung et al. (1984) have found that amorphous Ni-Mo films as diffusion barriers between multilayer metallizations on silicon demonstrate good electrical and thermal stability. In the present investigation, the Ni-W system was selected because it is similar to the Ni-Mo system. However, W has a higher silicide formation temperature than Mo. Attention is given to aspects of sample preparation, sample characterization, the interaction between amorphous Ni-W films and Si, the crystallization of amorphous Ni(36)W(64) films on SiO2, amorphous Ni-N-W films, silicide formation and phase separation, and the crystallization of amorphous Ni(36)W(64) and Ni(30)N(21)W(49) layers.
Zhu, M. F.↗
3rd harmonic magnetometry assessment of NbTiN-based SIS structures
In the quest for alternative superconducting materials to bring accelerator cavity performance beyond the bulk niobium (Nb) intrinsic limits, a promising concept proposes that superconductor-insulator-superconductor (SIS) thin film structures can delay magnetic flux penetration in accelerator cavities to higher fields [1]. NbTiN is a candidate superconductor for such structures. We have demonstrated high quality NbTiN and AlN deposited by reactive direct current magnetron sputtering (DCMS), both for individual layers and multilayers. Interface quality has been assessed for bi-layer stacks with various NbTiN and AlN thicknesses from 500 and 30 nm down to 3 and 1 nm. These SIS structures show continued sharp interfaces. The Hfp enhancement of the films was examined with 3rd harmonic magnetometry. The system was designed and built in an ongoing collaboration with CEA Saclay. It can measure 1? to 2? samples on a temperature controlled stage. This contribution presents the assessment of the first penetration field enhancement with 3rd harmonic magnetometry for standalone films and multilayer nanostructures.
Valente, Anne-Marie↗
Photostability of Ambient-Processed, Conjugated Polymer Electrochromic Devices Encapsulated by Bioderived Barrier Films
Polymer-based electrochromic devices (ECDs) are a promising technology for enabling low-voltage, disposable displays, yet are currently limited by photo-oxidative bleaching of the active materials. Here, renewable barrier films composed of cellulose and chitin are presented as an alternative to poly(ethylene terephthalate) (PET) for encapsulating ECDs. To assess barrier film effectiveness, lateral ECDs composed of poly(3,4-propylenedioxythiophene-(CH 2 OEtHx) 2 ) (P(ProDOT)) active layers were constructed and encapsulated with a multilayer barrier consisting of chitin nanofibers and cellulose nanocrystals spray cast onto a cellulose acetate substrate (oxygen transmission rate (OTR) = 29 cm 3 m –2 day –1 ), a commercially available PET film (OTR = 8.5 cm 3 m –2 day –1 ), and a high-performance PET-Al 2 O 3 multilayer barrier film (OTR < 1 cm 3 m –2 day –1 ). The photodegradation of the P(ProDOT) active layer was determined by measuring the evolution of the colorimetric contrast (ΔE*) and switching speeds as a function of light exposure (100 mW cm –2 , AM 1.5 G light). Photodegradation was found to proceed at a similar rate for all encapsulated devices (roughly 10 times more slowly than unencapsulated devices), highlighting the opportunity for replacing petroleum packaging with bioderived barrier films. Analysis of the switching kinetics, the shifts in optical absorbance, and evidence of chemical degradation indicate that both photochemical breakdown of the electrolyte and cross-linking of the P(ProDOT) active material are key drivers for loss of device performance when oxygen flux to the active material is limited. Furthermore, pathways toward better understanding photodegradation are then proposed with sustainability in mind for future ECD design.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Development of an improved protective cover/light block for multilayer insulation
The feasibility of using a scrim-reinforced, single metallized, 4-mil Tedlar film as a replacement for the Teflon coated Beta-cloth/single metallized 3-mil Kapton film presently used as the protective cover/light block for multilayer insulation (MLI) on the Orbiter, Spacelab, and other space applications was demonstrated. The proposed Tedlar concept is lighter and potentially lower in cost. Thermal analysis with the proper concept was much simpler than with the present system. Tests have already demonstrated that white Tedlar has low alpha (adsorption) degradation in space from U.V. The proposed concept was 4400 percent cheaper with nominal weight savings of 50 percent.
Thompson, L. M.↗
Thermal energy transport characteristics along the laminations of multilayer insulations.
Temperature dependent thermoconductivity of metal film on insulation laminations in relation to bulk parent material in insulation systems of cryogenic propellants
Coston, R. M.↗
Low temperature storage container for transporting perishables to space station
This invention is directed to the long term storage of frozen and refrigerated food and biological samples by the space shuttle to the space station. A storage container is utilized which has a passive system so that fluid/thermal and electrical interfaces with the logistics module is not required. The container for storage comprises two units, each having an inner storage shell and an outer shell receiving the inner shell and spaced about it. The novelty appears to lie in the integration of thermally efficient cryogenic storage techniques with phase change materials, including the multilayer metalized surface thin plastic film insulation and the vacuum between the shells. Additionally the fiberglass constructed shells having fiberglass honeycomb portions, and the lining of the space between the shells with foil combine to form a storage container which may keep food and biological samples at very low temperatures for very long periods of time utilizing a passive system.
Dean, William G↗
Picometer sensitivity metrology for EUV absorber phase
With growing interest in EUV attenuated phase-shift masks due to their superior image quality for applications such as dense contact and pillar arrays, it is becoming critical to model, measure, and monitor the intensity and relative phase of multilayer and absorber reflections. We present a solution based on physical modeling of reflectometry data, which can achieve single picometer phase precision and sensitivity to changes in average film thickness below one atomic monolayer. We measure absorber and multilayer reflectivity to determine thin-film parameters with a multidimensional optimization and then acquire a new measurement of either multilayer or absorber to determine perturbations in surface contamination thickness. While it is difficult to assess the accuracy of the first step, the simplicity of the second step allows us to characterize our sensitivity to changes in contamination thickness. Thus, we apply this analysis using an initial set of measurements and repeated measurements after a period of storage. For the multilayer, the total contamination growth was 1068 pm, which occurred almost exclusively during storage (1085 pm) and decreased very slightly during repeated measurements (-17 pm). For the absorber, the behavior was quite different, with a total growth of 126 pm, which occurred much less during storage (28 pm) and primarily during repeated measurements (98 pm). Ultimately, the change in relative phase (absorber minus multilayer) was -0.86 deg for the multilayer and -1.12 deg for the absorber. We estimate the precision of the surface contamination measurement to be 3σ < 6 pm for measuring thickness and 3σ < 0.2 deg for measuring phase.
36 MATERIALS SCIENCE↗
Restoration of weak localization in bilayer graphene by a molecular thin film
Quantum coherent effects can be probed in multilayer graphene through electronic transport measurements at low temperatures. In particular, bilayer graphene (BLG) is known to be susceptible to quantum interference corrections of the conductivity, presenting weak localization at all electronic densities, and dependent on different scattering mechanisms such as those related to the trigonal warping of the electron dispersion near the K and K′ valleys. Proximity effects with a molecular thin film influence these scattering mechanisms, which can be quantified through the known theory of magnetoconductance for BLG. Here, we present electronic transport measurements in a copper-phthalocyanine (CuPc) / BLG / hexagonal boron nitride (h-BN) heterostructure that suggest the restoration of weak localization in BLG, associated to a reduction of trigonal warping effects, that are known to suppress weak localization in BLG. Additionally, we observe a charge transfer of 3.6×10 12 cm −2 from the BLG to the molecules, as well as a very small degradation of the mobility of the BLG/h-BN heterostructure upon the deposition of CuPc. The molecular arrangement of the CuPc thin film is characterized in a control sample through transmission electron microscopy, that we relate to the electronic transport results.
bilayer graphene↗