Results for “Novel Processing” — Page 14

NASA NTRS1994

Chemical recycling of scrap composites

There are no well-developed technologies for recycling composite materials other than grinding to produce fillers. New approaches are needed to reclaim these valuable resources. Chemical or tertiary recycling, conversion of polymers into low molecular weight hydrocarbons for reuse as chemicals or fuels, is emerging as the most practical means for obtaining value from waste plastics and composites. Adherent Technologies is exploring a low-temperature catalytic process for recycling plastics and composites. Laboratory results show that all types of plastics, thermosets as well as thermoplastics, can be converted in high yields to valuable hydrocarbon products. This novel catalytic process runs at 200 C, conversion times are rapid, the process is closed and, thus, nonpolluting, and no highly toxic gas or liquid products have been observed so no negative environmental impact will result from its implementation. Tests on reclamation of composite materials show that epoxy, imide, and engineering thermoplastic matrices can be converted to low molecular weight hydrocarbons leaving behind the reinforcing fibers for reuse as composite reinforcements in secondary, lower-performance applications. Chemical recycling is also a means to dispose of sensitive or classified organic materials without incineration and provides a means to eliminate or reduce mixed hazardous wastes containing organic materials.

Allred, Ronald E.↗

NASA NTRS2021

A High Dynamic-Range Photon-Counting Receiver for Deep Space Optical Communication

The Deep Space Optical Communication (DSOC) project will demonstrate free-space optical communication at almost 3 AU, or 3 orders of magnitude further than any previous attempt. DSOC will utilize the 5m Palomar Hale Telescope to receive the downlink signal, which will couple the downlink light onto an optical table and into a superconducting nanowire single photon detector (SNSPD). The output of the SNSPD is digitized by the Ground Laser Receiver Signal Processing Assembly (GSPA) using a high throughput streaming time to digital converter (TDC). The GSPA is a scalable FPGA-based receiver which demodulates and decodes the DSOC downlink signal through novel signal processing algorithms implemented on Xilinx UltraScale+ FPGAs, as well as Python-based software monitor and control routines. Exploiting the unique TDC-based architecture, the GSPA supports over four orders of magnitude of downlink data rates across multiple orders of magnitude of signal and background powers. In this paper we present an overview of the hardware, firmware and software architectures to implement this system, as well as performance analysis for links ranging from near-Earth to 2.8 AU.

Srinivasan, Meera↗

DOE OSTI2023

Investigating microstructural evolution in SolidStir™ extruded oxide dispersion strengthened 14YWT alloy fuel cladding tube

Structural components for extreme environments require advanced materials and manufacturing processes. One such advanced material is oxide dispersion strengthened (ODS) Fe–14 wt.%Cr–3W–0.4Ti–0.3Y 2 O 3 (14YWT), which is developed for components to be used in Gen IV and fusion nuclear reactors. However, the conventional manufacturing processes to produce components, such as fuel cladding tubes, either do not retain the desired microstructural attributes or are costly and less efficient. As a result, a more attractive option is a novel manufacturing process developed on the principle of friction stir welding or processing (FSW/P) and commercially referred to as SolidStir™ Extrusion (SSE). Here this study used the SSE technique to study the manufacturing and microstructural evolution of a fuel cladding tube made of ODS 14YWT alloy. The cladding extrusion by the SSE technique involved the use of ball-milled 14YWT powders with Y, Ti, and O in the solid solution and the use of a specially designed W-25Re-Hf tool for consolidation and extrusion of the powders. A scanning electron microscope (SEM), electron backscattered diffraction (EBSD), and transmission electron microscope (TEM) were utilized for microstructural characterization. A Keyence microscope captured macrostructural photographs of the extruded tube. EBSD examination of the extruded tube on both transverse and longitudinal cross-sections showed the presence of dynamically recrystallized grains and revealed that the average grain size of the transverse cross-section was smaller than that of the longitudinal cross-section. The texture was weak and consisted of some amount of shear texture. The presence of nano-oxide clusters or precipitates of Y, Ti, and O (pyrochlores) in the extruded tube was determined by TEM. Aging heat treatment caused the average precipitate size to decrease and the density to increase compared to the as-processed condition. The results indicated that SSE is a viable tool for manufacturing fuel cladding tubes with the desired microstructural attributes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2020

Improved Performance of Cu(InGa)(SeS) 2 PV Modules Using the Reaction of Metal Precursors. Final Report

This project “Improved Performance of Cu(InGa)(SeS) 2 PV Modules using the Reaction of Metal Precursors” was a partnership led by the Institute of Energy Conversion (IEC) at the University of Delaware with Columbia University and the Molecular Foundry at the Lawrence Berkeley National Laboratory. The aim was to develop pathways to improve Cu(InGa)(SeS) 2 (CIGSS) thin film photovoltaic modules using processes compatible with low manufacturing cost. The CIGSS approach investigated was a two-step process including deposition of metal precursor films following by reaction in hydride gases utilizing IEC’s novel reactor. The process was similar to that under commercial development by the project’s industry partner Stion. When Stion went out of business mid-project the focus changed to a rapid thermal process considered more commercially viable. Approaches to improve the performance of solar cells using the reacted films focused on two material innovations. First, the overall Ga content was increased to increase the operating voltage, which is desirable for scale-up to commercial modules. Second, the processing and performance advantages arising from Ag alloying were investigated. Advanced characterization guided process and material development including control of relative composition gradients. Research on the formation of Cu-Ga-In metal precursors utilized sputtering deposition which is normally used in commercial applications. The work resulted in processes for deposition of precursor stacks with increased relative Ga content and effects of deposition parameters on morphology and phase composition were established. It was shown that the metal precursor films have comparable phase composition and morphology so subsequent reaction follows from the same starting point. The addition of Ag to the metal precursors gave more uniform morphology and improved adhesion of reacted films which enable higher reaction temperature for faster processing. A novel outcome was the discovery of a previously undocumented material phase in sputter-deposited and evaporated Ag-Cu-In-Ga thin films. Hydride gas reaction processes including time-temperature-concentration profiles were developed for different precursor compositions. This enables control of composition profiles to engineer through-film gradients for solar cell optimization with characterization and simulations used to correlate measured film composition profiles to measurements of devices. In particular, the gradient of sulfur at the front of the CIGSS film was found to be critical. The simulations guided process development leading to improved reproducibility of devices improved performance with higher Ga content and higher voltage. With Ag-alloyed precursors, the reaction pathways leading were determined. A significant finding was that Ag-alloying increases the reaction rate to completely convert precursor films to the final chalcopyrite which could enable reduced reaction time to benefit manufacturability. To maintain potential commercial viability, the process under investigation was refocused to a rapid thermal process that could potentially be incorporated into an in-line process for manufacturing. Precursors with different composition were capped with an extra selenium layer and reacted in hydrogen sulfide 5-15 minutes, compared to typically 2 hours in the previous multi-step batch process. Critical RTP parameters were identified to control the reaction. Further optimization would be needed for high efficiency solar cells but pathways to high quality devices with further optimization and improved heating uniformity were developed. The project also developed new optoelectronic characterization approaches with a focus on development and application of spatial- and time-resolved photoluminescence and a custom mapping photoluminescence microscope built. It was shown how critical electronic transport properties strongly depend on the chemical composition of the material and that a wide range of samples show inhomogeneity on a length scale larger than the grains in the films. Additionally, two-photon excitation capability was developed to distinguish bulk vs surface losses. The project advances the state-of-the -art for precursor reaction processes in several ways that could impact manufacturing. This includes validation of approaches to increase voltage and establishment of model-guided control to form optimal composition profiles. The application of process control approaches with knowledge of phase formation and reaction pathways can be critically valuable in designing a large-scale process.

14 SOLAR ENERGY↗

DOE OSTI2019

Atom Probe Tomography for understanding microstructural and chemical changes in nuclear materials

Atom Probe Tomography (APT) is routinely employed to determine 3D microstructure and chemistry changes in structural materials used in reactor to understand irradiation effect. These findings help to correlate changes to mechanical and physical properties of nuclear materials which are subjected to extreme reactor conditions. With safety and economics of a reactor in mind, it is essential to be able to predict the changes in the fuel composition and microstructure as a function of burnup. Also, there is current need to develop advanced fuels with improved properties and performance which requires the experimental data on changes in microstructure, physical and chemical properties after irradiation for feedback process. A novel approach is presented to determine the local burnup in irradiated fuels using isotopic quantification obtained by Atom Probe Tomography (APT). Considering the volume of sample used (<100?µm3) for APT experiments using the lift-out process in a scanning electron microscope equipped with a Focused Ion Beam (FIB), the presented method determines the local burnup from a nuclear fuel, where a minimal amount of waste is produced. In this work, three samples were analyzed with different burnup conditions to quantify the isotopes of 235U, 236U, and 238U for burnup calculation in the irradiated metallic U–7Mo dispersion fuel. The calculated values were found in excellent agreement with MCNP calculations. With regard to structural materials, one of the primary factors limiting the utilization of fuel rods of Zr alloys is hydrogen pick up during oxidation. Past experimental studies have shown that the hydrogen pickup in Zirconium alloys is influenced by the alloy composition as well by irradiation temperature and neutron dose. Oftentimes, it is not feasible to carry out comprehensive studies on understanding the microstructural evolution in neutron irradiated materials since in reactor irradiation programs are extremely costly, lengthy and logistically complicated. The use of ion irradiation as a substitute has grown in recent years for several reasons including less radioactivity, faster irradiations and lower costs. In the framework of the MUZIC 3 project, samples of Zircaloy-4 have been proton and Zr2+ irradiated at the Michigan Ion Beam Lab (MIBL) facility with aim to create a microstructure that is similar to that observed after in-reactor service. The temperature of the environment is adjusted to compensate for the higher dose rate, as has been done previously. As a first step in this project the irradiated microstructures have been characterized using Transmission Electron Microscopy and Atom Probe Tomography to elucidate the microstructural changes, including precipitate amorphization and dissolution and the formation of dislocation loops. This presentation plans to highlight initial finding of this project.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2023

Topological Relationship-Based Flow Direction Modeling: Stream Burning and Depression Filling

Flow direction modeling consists of (a) an accurate representation of the river network and (b) digital elevation model (DEM) processing to preserve characteristics with hydrological significance. In part 1 of our study, we presented a mesh-independent approach to representing river networks on different types of meshes. This follow-up part 2 study presents a novel DEM processing approach for flow direction modeling. This approach consists of (a) a topological relationship-based hybrid breaching-filling method to conduct stream burning for the river network and (b) a modified depression removal method for rivers and hillslopes. Our methods reduce modifications to surface elevations and provide a robust two-step procedure to remove local depressions in DEM. They are mesh-independent and can be applied to both structured and unstructured meshes. We applied our new methods with different model configurations to the Susquehanna River Basin. The results show that topological relationship-based stream burning, and depression-filling methods can reproduce the correct river networks, providing high-quality flow direction and other characteristics for hydrologic and Earth system models.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

WaterTAP 0.3 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2022

WaterTAP 0.4 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2022

WaterTAP 0.5 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2022

WaterTAP 0.6 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2022

WaterTAP 0.7 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2023

WaterTAP 0.8 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2023

WaterTAP 0.10 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2024

WaterTAP 0.11 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2024

WaterTAP 0.12 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

IDAES↗

DOE OSTI2024

WaterTAP 1.0 Release

The Water treatment Technoeconomic Assessment Platform (WaterTAP) is an open-source Python-based software package that supports the simulation and optimization of process-scale water treatment trains. WaterTAP seeks to provide the broader water research community with an integrated modeling capability to evaluate cost, energy, and environmental tradeoffs across water treatment options and identify high impact opportunities for innovation including novel materials, processes, and systems. An updated version of WaterTAP is released quarterly and each includes documentation and release notes.

AS↗

NASA NTRS1976

A real-time optical data processing device

A novel liquid-crystal electro-optical device useful as a real-time input device in coherent optical data processing is described. The device is a special adaptation of an ac photoactivated liquid-crystal light valve, and utilizes a hybrid field effect (45 deg twisted nematic effect in OFF state and pure optical birefringence of the liquid crystal in ON state). A thin-film sandwich exerts photoelectric control over the optical birefringence of a thin liquid-crystal layer. Liquid-crystal layer thickness is successfully reduced without image degradation. The device offers high resolution (better than 100 lines/mm), contrast (better than 100/1), high speed (10 msec ON, 15 msec OFF), high input sensitivity, low power input, low fabrication cost, and can be operated at below 10 V rms. Preliminary measurements on device performance in level slicing, filtering, contrast reversal, and edge enhancement are under way.

Jacobson, A.↗

DOE OSTI2024

Non-smooth Bayesian optimization in tuning scientific applications

Tuning algorithmic parameters to optimize the performance of large, complicated computational codes is an important problem involving finding the optima and identifying regimes defined by non-smooth boundaries in black-box functions. Within the Bayesian optimization framework, the Gaussian process surrogate model produces smooth mean functions, but functions in the tuning problem are often non-smooth, which is exacerbated by the fact that we usually have limited sequential samples from the black-box function. Here, motivated by these issues encountered in tuning, we propose a novel Gaussian process model called a clustered Gaussian process (cGP), where the components are dynamically updated by clustering. In our studies, the performance of cGP can be better than stationary GPs in nearly 90% of the experiments and better than non-stationary GPs in nearly 70% of the repeated experiments while requiring less computational cost. cGP provides a novel approach for dynamic GP, computes more efficiently than recursive partitioning, and discovers non-smoothness regimes. We provide extensive experiments including high-performance computing (HPC) and industrial simulation functions to show the effectiveness of our methods.

97 MATHEMATICS AND COMPUTING↗