Search NASA⌕ Search

SEARCH · Search NASA

Results for “Numerical diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Numerical Modeling of Flow Control in a Boundary-Layer-Ingesting Offset Inlet Diffuser at Transonic Mach Numbers

This paper will investigate the validation of a NASA developed, Reynolds-averaged Navier-Stokes (RANS) flow solver, OVERFLOW, for a boundary-layer-ingesting (BLI) offset (S-shaped) inlet in transonic flow with passive and active flow control devices as well as the baseline case. Numerical simulations are compared to wind tunnel results of a BLI inlet conducted at the NASA Langley 0.3-Meter Transonic Cryogenic Tunnel. Comparisons of inlet flow distortion, pressure recovery, and inlet wall pressures are performed. The numerical simulations are compared to the BLI inlet data at a freestream Mach number of 0.85 and a Reynolds number of approximately 2 million based on the length of the fan-face diameter. The numerical simulations with and without wind tunnel walls are performed, quantifying effects of the tunnel walls on the BLI inlet flow measurements. The wind tunnel test evaluated several different combinations of jet locations and mass flow rates as well as a vortex generator (VG) vane case. The numerical simulations will be performed on a single jet configuration for varying actuator mass flow rates at a fix inlet mass flow condition. Validation of the numerical simulations for the VG vane case will also be performed for varying inlet mass flow rates. Overall, the numerical simulations were able to predict the baseline circumferential flow distortion, DPCPavg, very well for comparisons made within the designed operating range of the BLI inlet. However the CFD simulations did predict a total pressure recovery that was 0.01 lower than the experiment. Numerical simulations of the baseline inlet flow also showed good agreement with the experimental inlet centerline surface pressures. The vane case showed that the CFD predicted the correct trends in the circumferential distortion for varying inlet mass flow but had a distortion level that was nearly twice as large as the experiment. Comparison to circumferential distortion measurements for a 15 deg clocked 40 probe rake indicated that the circumferential distortion levels are very sensitive to the symmetry of the flow and that a miss alignment of the vanes in the experiment could have resulted in this difference. The numerical simulations of the BLI inlet with jets showed good agreement with the circumferential inlet distortion levels for a range of jet actuator mass flow ratios at a fixed inlet mass flow rate. The CFD simulations for the jet case also predicted an average total pressure recovery that was 0.01 lower than the experiment as was seen in the baseline. Comparison of the flow features the jet case revealed that the CFD predicted a much larger vortex at the engine fan-face when compare to the experiment.

Allan Brian G.↗
NASA NTRS2014

A High-Resolution X-Ray and Optical Study of SN1006: Asymmetric Expansion and Small-Scale Structure in a Type Ia Supernova Remnant

We introduce a deep (670 ks) X-ray survey of the entire SN 1006 remnant from the Chandra X-Ray Observatory, together with a deep Hα image of SN 1006 from the 4 m Blanco telescope at CTIO. Comparison with Chandra images from 2003 gives the first measurement of the X-ray proper motions around the entire periphery, carried out over a 9 yr baseline. We find that the expansion velocity varies significantly with azimuth. The highest velocity of approx.7400 km/s (almost 2.5 times that in the northwest (NW)) is found along the southeast (SE) periphery, where both the kinematics and the spectra indicate that most of the X-ray emission stems from ejecta that have been decelerated little, if at all. Asymmetries in the distribution of ejecta are seen on a variety of spatial scales. Si-rich ejecta are especially prominent in the SE quadrant, while O and Mg are more uniformly distributed, indicating large-scale asymmetries arising from the explosion itself. Neon emission is strongest in a sharp filament just behind the primary shock along the NWrim, where the pre-shock density is highest. Here the Ne is likely interstellar, while Ne within the shell may include a contribution from ejecta. Within the interior of the projected shell we find a few isolated "bullets" of what appear to be supernova ejecta that are immediately preceded by bowshocks seen in Hα, features that we interpret as ejecta knots that have reached relatively dense regions of the surrounding interstellar medium, but that appear in the interior in projection. Recent three-dimensional hydrodynamic models for Type Ia supernovae display small-scale features that strongly resemble the ones seen in X-rays in SN 1006; an origin in the explosion itself or from subsequent hydrodynamic instabilities both remain viable options. We have expanded the search for precursor X-ray emission ahead of a synchrotron-dominated shock front, as expected from diffusive shock acceleration theory, to numerous regions along both the northeast and southwest rims of the shell. Our data require that a precursor be thinner than about 3, and fainter than about 5% of the post-shock peak. These limits suggest that the magnetic field is amplified by a factor of seven or more in a narrow precursor region, promoting diffusive particle acceleration.

galaxies: active↗
NASA NTRS1985

A comparison between implicit and hybrid methods for the calculation of steady and unsteady inlet flows

Numerical simulation of steady and unsteady transonic diffuser flows using two different computer codes are discussed and compared with experimental data. The codes solve the Reynolds-averaged, compressible, Navier-Stokes equations using various turbulence models. One of the codes has been applied extensively to diffuser flows and uses the hybrid method of MacCormack. This code is relatively inefficient numerically. The second code, which was developed more recently, is fully implicit and is relatively efficient numerically. Simulations of steady flows using the implicit code are shown to be in good agreement with simulations using the hybrid code. Both simulations are in good agreement with experimental results. Simulations of unsteady flows using the two codes are in good qualitative agreement with each other, although the quantitative agreement is not as good as in the steady flow cases. The implicit code is shown to be eight times faster than the hybrid code for unsteady flow calculations and up to 32 times faster for steady flow calculations. Results of calculations using alternative turbulence models are also discussed.

Coakley, T. J.↗
NASA NTRS1989

Nonclassical nucleation and growth of cohesive tensile cracks

The nucleation and growth of cohesive tensile cracks are analyzed using a field-theoretic formulation in which the free energy is written as a functional of the crack separation (offset field). The present results indicate that, for certain materials, crack nucleation and growth proceed through the formation and extension of a diffuse 'halo' surrounding the classical portion of the crack. This is similar to nonclassical nucleation in magnetic systems. Theoretical considerations and numerical calculations strongly suggest that the diffuse halo can be identified with the fracture process zone seen in laboratory studies of advancing cracks.

Rundle, John B.↗
NASA NTRS1990

Pitch angle diffusion of newborn ions due to intrinsic turbulence in the solar wind

The objective of the present study is to understand the interaction of the solar wind with newborn ions in far upstream regions of a comet where the level of intrinsic turbulence is moderately low. Based on the assumption that quasi-linear theory is adequate and applicable, the pitch angle diffusion process and the time evolution of the newborn ion distribution function are investigated. Numerical solutions to the quasi-linear diffusion equation, including the effect of resonance broadening and that of continuous creation of newborn ions due to the ionization process, are obtained under several assumptions and approximations. It is found that theoretical results are consistent with the Giotto observations recently reported by Neugebauer et al. (1989).

Ziebell, L. F.↗
NASA NTRS1960

Heat Diffusion in Gases, Including Effects of Chemical Reaction

The diffusion of heat through gases is treated where the coefficients of thermal conductivity and diffusivity are functions of temperature. The diffusivity is taken proportional to the integral of thermal conductivity, where the gas is ideal, and is considered constant over the temperature interval in which a chemical reaction occurs. The heat diffusion equation is then solved numerically for a semi-infinite gas medium with constant initial and boundary conditions. These solutions are in a dimensionless form applicable to gases in general, and they are used, along with measured shock velocity and heat flux through a shock reflecting surface, to evaluate the integral of thermal conductivity for air up to 5000 degrees Kelvin. This integral has the properties of a heat flux potential and replaces temperature as the dependent variable for problems of heat diffusion in media with variable coefficients. Examples are given in which the heat flux at the stagnation region of blunt hypersonic bodies is expressed in terms of this potential.

Hansen, C. Frederick↗
NASA NTRS2022

Diffusion in Melts and Magmas

Diffusion results from random motion of particles and entities. Diffusion in melts and magmas is due to thermally excited random motion of atoms, ions, and clusters, and plays a critical role in magmatic and volcanic processes. In melts and magmas, diffusion is one of the two mechanisms of mass transfer; the other being bulk flow (referred to as convection or advection). When both are present, diffusion refers to the dispersive motion relative to the mean bulk flow in a given reference frame (Richter et al. 1998). Diffusion plays critical roles in controlling magma mixing (Watson 1982; Koyaguchi 1985, 1989; Lesher 1994; Huber et al. 2009; Guo and Zhang 2020), mineral growth and dissolution rates in magmas (e.g., Watson 1982; Harrison and Watson 1983; Zhang et al. 1989; Newcombe et al. 2014; Macris et al. 2018), bubble growth and dissolution rate in magmas (Sparks 1978; Proussevitch and Sahagian 1998; Liu and Zhang 2000; Zhang 2013), and elemental and isotope fractionation during mineral 2 growth and dissolution (Jambon 1980; Richter et al. 1999, 2003; Watson and Muller 2009; Chopra et al. 2012; Watkins et al. 2014, 2017; Holycross et al. 2016, 2018). As a result, diffusion also plays an essential role in explosive volcanic eruptions and magma crystallization. Furthermore, diffusion has important applications in geospeedometry (Lasaga 1983, 1998; Zhang 1994, 2008; Trail et al. 2016; Zhang and Xu 2016). Experimental investigation of diffusion in geologically relevant silicate melts began to flourish in the 1970’s when micro-analytical measurements of diffusion profiles became available. In addition to the vast number of papers published since then, numerous books and reviews are available for diffusion in silicate melts. Hofmann et al. (1974) edited a book titled “Geochemical Transport and Kinetics” published by Carnegie Institution of Washington. This was the first landmark book summarizing the field. Lasaga and Kirkpatrick (1981) edited a book “Kinetics of Geochemical Processes” as volume 8 of the Reviews in Mineralogy (later becoming Reviews in Mineralogy and Geochemistry) series. Zhang and Cherniak (2010) edited “Diffusion in Minerals and Melts” as volume 72 of Reviews of Mineralogy and Geochemistry series, in which one chapter focused on diffusion theory, five chapters on diffusion in silicate melts (Behrens 2010; Lesher 2010; Liang 2010; Zhang and Ni 2010; Zhang et al. 2010), and other chapters were on experimental, analytical, and computational methods, and diffusion in minerals. Several textbooks covered the principles and applications of diffusion theories (Kirkaldy and Young 1987; Shewmon 1989; Cussler 1997; Lasaga 1998; Zhang 2008; Vrentas and Vrentas 2016), and two classic books covered the mathematics of diffusion (Carslaw and Jaeger 1959; Crank 1975). In preparing for this review chapter, we thought carefully about what to cover for this vast field, and decided to briefly go through the fundamentals of diffusion (more complete review can be found in Chakraborty 1995; Zhang 2008, 2010) and solutions to often-encountered 3 diffusion problems, and then focus on post-2010 diffusion studies on silicate melts and magmas. Here, melts refer to (mostly natural) silicate liquid, and magmas refer to crystal-bearing and/or bubble-bearing melts in which the continuous phase is the melt. There is a large body of work on diffusion in glasses, especially in the materials science literature, which is not covered in this review.

Youxue Zhang↗
NASA NTRS1994

Stochastic acceleration of energetic ions in Jupiter's magnetosphere

An equation governing the combined radial diffusion and stochastic acceleration of super-Alfvenic ions by magnetohydrodynamic waves in Jupiter's outer magnetosphere is derived. The formulation is based upon a total energy invariant of the adiabatic transport which applies to an isotropic distribution undergoing rapid pitch angle scattering by waves. An analytic solution to the double diffusion equation is obtained and numerical results are presented for two models of ion injection. The first model assumes S(+) and O(+) are injected throughout a broad region of space through photoionization of Jupiter's magnetospheric neutral wind and obtain an initial energy corresponding to the local corotation energy after pickup by the planetary magnetic field. The second model assumes a monoenergetic distribution of energetic protons is implanted in the middle magnetosphere by the action of field-aligned potential drops in Jupiter's auroral ionosphere. For both light and heavy ions the injection process creates a seed population of particles which are further accelerated nonadiabatically by the MHD waves and adiabatically through radial diffusion. A comparison of the theoretical results with a recent data analysis of Voyager low-energy charged particle measurements is made with very good agreement, thus providing a rigorous quantitative account of and definitive explanation for the high-energy ion component of Jupiter's magnetosphere.

Barbosa, D. D.↗
NASA NTRSDate not supplied

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

vaned diffuser↗
NASA NTRS1971

Numerical calculation of turbulent boundary layers including suction or injection with binary diffusion.

The modelling of turbulent transport processes with an eddy viscosity representation of the inner, wall region for cases with suction or injection is considered in detail. It is shown how the van Driest solid wall model can be logically extended for such cases. Further, a new inductive model is developed. Finite difference calculations using the new inductive model are shown to be in good agreement with experimental data over a wide range of conditions. Lastly, a new method for calculating the wall shear within a finite difference solution is developed. This procedure greatly relaxes the requirement for fine grid spacing in the vertical direction.

Schetz, J. A.↗
NASA NTRSDate not supplied

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

centrifugal compressor↗
NASA NTRS2001

Cool Flame Quenching

Cool flame quenching distances are generally presumed to be larger than those associated with hot flames, because the quenching distance scales with the inverse of the flame propagation speed, and cool flame propagation speeds are often times slower than those associated with hot flames. To date, this presumption has never been put to a rigorous test, because unstirred, non-isothermal cool flame studies on Earth are complicated by natural convection. Moreover, the critical Peclet number (Pe) for quenching of cool flames has never been established and may not be the same as that associated with wall quenching due to conduction heat loss in hot flames, Pe approx. = 40-60. The objectives of this ground-based study are to: (1) better understand the role of conduction heat loss and species diffusion on cool flame quenching (i.e., Lewis number effects), (2) determine cool flame quenching distances (i.e, critical Peclet number, Pe) for different experimental parameters and vessel surface pretreatments, and (3) understand the mechanisms that govern the quenching distances in premixtures that support cool flames as well as hot flames induced by spark-ignition. Objective (3) poses a unique fire safety hazard if conditions exist where cool flame quenching distances are smaller than those associated with hot flames. For example, a significant, yet unexplored risk, can occur if a multi-stage ignition (a cool flame that transitions to a hot flame) occurs in a vessel size that is smaller than that associated with the hot quenching distance. To accomplish the above objectives, a variety of hydrocarbon-air mixtures will be tested in a static reactor at elevated temperature in the laboratory (1g). In addition, reactions with chemical induction times that are sufficiently short will be tested aboard NASA's KC-135 microgravity (mu-g) aircraft. The mu-g results will be compared to a numerical model that includes species diffusion, heat conduction, and a skeletal kinetic mechanism, following the work on diffusion-controlled cool flames by Fairlie et,al., 2000.

Pearlman, Howard↗
NASA NTRS1984

Direct simulations of chemically reacting turbulent mixing layers

The report presents the results of direct numerical simulations of chemically reacting turbulent mixing layers. The work consists of two parts: (1) the development and testing of a spectral numerical computer code that treats the diffusion reaction equations; and (2) the simulation of a series of cases of chemical reactions occurring on mixing layers. The reaction considered is a binary, irreversible reaction with no heat release. The reacting species are nonpremixed. The results of the numerical tests indicate that the high accuracy of the spectral methods observed for rigid body rotation are also obtained when diffusion, reaction, and more complex flows are considered. In the simulations, the effects of vortex rollup and smaller scale turbulence on the overall reaction rates are investigated. The simulation results are found to be in approximate agreement with similarity theory. Comparisons of simulation results with certain modeling hypotheses indicate limitations in these hypotheses. The nondimensional product thickness computed from the simulations is compared with laboratory values and is found to be in reasonable agreement, especially since there are no adjustable constants in the method.

Riley, J. J.↗
NASA NTRS1983

Analytical and Numerical Solution for a Solidifying Liquid Alloy Slab

Numerical and analytical solutions are presented for the temperature and concentration distributions during the solidification of a binary liquid alloy slab. The slab is taken to be of a finite depth but infinite in the horizontal direction. The solidification process is started by withdrawing a fixed amount of heat from the lower surface of the slab. The upper surface of the slab is subjected to both radiation and convective conditions. The solution gives the concentration and temperature profiles and the interface position as a function of time. Due to the smallness of the mass diffusion coefficient in the solid, the numerical solution method breaks down whenever the ratio of the diffusivities in the solid and the liquid falls below a certain value. An analytical method is developed which gives accurate solution for any value of the diffusivity ratio.

Antar, B. N.↗
NASA NTRS2003

Elevated Temperature Creep Deformation in Solid Solution <001> NiAL-3.6Ti Single Crystals

The 1100 to 1500 K slow plastic strain rate compressive properties of <001> oriented NiAl-3.6Ti single crystals have been measured, and the results suggests that two deformation processes exist. While the intermediate temperature/faster strain rate mechanism is uncertain, plastic flow at elevated temperature/slower strain rates in NiAl-3.6Ti appears to be controlled by solute drag as described by the Cottrell-Jaswon solute drag model for gliding b = a(sub 0)<101> dislocations. While the calculated activation energy of deformation is much higher (approximately 480 kJ/mol) than the activation energy for diffusion (approximately 290 kJ/mol) used in the Cottrell-Jaswon creep model, a forced temperature compensated - power law fit using the activation energy for diffusion was able to adequately (greater than 90%) predict the observed creep properties. Thus we conclude that the rejection of a diffusion controlled mechanism can not be simply based on a large numerical difference between the activation energies for deformation and diffusion.

Whittenberger, J. Daniel↗
NASA NTRS1974

Experimental determination of turbulence in a GH2-GOX rocket combustion chamber

The intensity of turbulence and the Lagrangian correlation coefficient for a gaseous rocket combustion chamber have been determined from the experimental measurements of the tracer gas diffusion. A combination of Taylor's turbulent diffusion theory and Spalding's numerical method for solving the conservation equations of fluid mechanics was used to calculate these quantities. Taylor's theory was extended to consider the inhomogeneity of the turbulence field in the axial direction of the combustion chamber. An exponential function was used to represent the Lagrangian correlation coefficient. The results indicate that the maximum value of the intensity of turbulence is about 15% and the Lagrangian correlation coefficient drops to about 0.12 in one inch of the chamber length.

Tou, P.↗
NASA NTRS1978

Measurement of the turbulence in a gaseous rocket combustion chamber

The intensity of turbulence and the Lagrangian correlation coefficient in a gaseous hydrogen (GH2)-gaseous oxygen (GOX) rocket combustion chamber are studied. A helium tracer gas was injected at an upstream point on the combustion chamber centerline. Samples collected downstream were analyzed for the spreading of the tracer gas concentration. Using Taylor's turbulent diffusion theory and Gosman's numerical method, turbulence parameters were found. In order to evaluate turbulence field inhomogeneity in the axial direction, Taylor's theory was extended. An exponential function was used to approximate the Lagrangian correlation coefficient. It was found that turbulence intensity varies from 15% near the injector to 4% at the nozzle entrance, and that the Lagrangian coefficient rapidly decreases when the dispersion time difference increases.

Tou, P. P.↗