Search NASA⌕ Search

SEARCH · Search NASA

Results for “Numerical software”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14

A model-based approach to the symbolic control of space subsystems

A multilayered approach to the symbolic control of complex electromechanical assemblies, such as spaceborne thermal, power, and life subsystems, is discussed. An example of this approach is given in some recent tests of the Thermal Expert System (TEXSYS) in control of the Boeing Aerospace Thermal Bus System (BATBS), a prototype two-phase Space Station Freedom thermal bus. The BATBS hardware requires read-update-act cycles of under a minute, and it is subject to dynamic reconfiguration while operating. These performance requirements are addressed by layering model-based expert system software on a conventional numerical data acquisition and control system. TEXSYS test results demonstrate both nominal control and fault recovery actions with the BATBS. Dynamic modification of the symbolic model used in this approach is compared to that of a classical numerical adaptive controller.

Glass, B. J.↗

Results of the Systems Autonomy Demonstration Project

The Systems Autonomy Demonstration Project (SADP) produced a knowledge-based real-time control system for real-time control and fault detection, isolation and recovery (FDIR) of a prototype two-phase Space Station Freedom external control system (TCS). The Thermal Expert System (TEXSYS) was demonstrated in recent tests to be capable of reliable fault anticipation and detection, as well as nominal control of the thermal bus. Performance requirements were addressed by adopting a hierarchical symbolic control approach, layering model-based expert system software on a conventional numerical data acquisition and control system. The model-based capabilities of TEXSYS were shown to be advantageous, particularly for detection of unforeseen faults and sensor failures.

Glass, B. J.↗

Distributed interactive graphics applications in computational fluid dynamics

Implementation of two interactive, distributed graphics programs used in Computational Fluid Dynamics is discussed. Both programs run on a Cray 2 supercomputer and use a Silicon Graphics Iris workstation as the graphics front-end machine. The hardware and supporting software is from the Numerical Aerodynamic Simulation project. Using this configuration, the supercomputer does all of the numerically intensive work and the workstation allows the user to perform real-time interactive transformations on the displayed data. The first program was written originally as a distributed program which computes particle traces for fluid flow solutions existing on the supercomputer. The second is an older post-processing and plotting program which was modified to run in a distributed mode. Both programs have realized a large increase in capability as a distributed process. Some graphical results are presented.

Rogers, Stuart E.↗

Parallelizing OVERFLOW: Experiences, Lessons, Results

The computer code OVERFLOW is widely used in the aerodynamic community for the numerical solution of the Navier-Stokes equations. Current trends in computer systems and architectures are toward multiple processors and parallelism, including distributed memory. This report describes work that has been carried out by the author and others at Ames Research Center with the goal of parallelizing OVERFLOW using a variety of parallel architectures and parallelization strategies. This paper begins with a brief description of the OVERFLOW code. This description includes the basic numerical algorithm and some software engineering considerations. Next comes a description of a parallel version of OVERFLOW, OVERFLOW/PVM, using PVM (Parallel Virtual Machine). This parallel version of OVERFLOW uses the manager/worker style and is part of the standard OVERFLOW distribution. Then comes a description of a parallel version of OVERFLOW, OVERFLOW/MPI, using MPI (Message Passing Interface). This parallel version of OVERFLOW uses the SPMD (Single Program Multiple Data) style. Finally comes a discussion of alternatives to explicit message-passing in the context of parallelizing OVERFLOW.

Jespersen, Dennis C.↗

Probabilistic Structural Analysis of the Solid Rocket Booster Aft Skirt External Fitting Modification

NASA has funded several major programs (the Probabilistic Structural Analysis Methods Project is an example) to develop probabilistic structural analysis methods and tools for engineers to apply in the design and assessment of aerospace hardware. A probabilistic finite element software code, known as Numerical Evaluation of Stochastic Structures Under Stress, is used to determine the reliability of a critical weld of the Space Shuttle solid rocket booster aft skirt. An external bracket modification to the aft skirt provides a comparison basis for examining the details of the probabilistic analysis and its contributions to the design process. Also, analysis findings are compared with measured Space Shuttle flight data.

Townsend, John S.↗

CRITICA: coding region identification tool invoking comparative analysis

Gene recognition is essential to understanding existing and future DNA sequence data. CRITICA (Coding Region Identification Tool Invoking Comparative Analysis) is a suite of programs for identifying likely protein-coding sequences in DNA by combining comparative analysis of DNA sequences with more common noncomparative methods. In the comparative component of the analysis, regions of DNA are aligned with related sequences from the DNA databases; if the translation of the aligned sequences has greater amino acid identity than expected for the observed percentage nucleotide identity, this is interpreted as evidence for coding. CRITICA also incorporates noncomparative information derived from the relative frequencies of hexanucleotides in coding frames versus other contexts (i.e., dicodon bias). The dicodon usage information is derived by iterative analysis of the data, such that CRITICA is not dependent on the existence or accuracy of coding sequence annotations in the databases. This independence makes the method particularly well suited for the analysis of novel genomes. CRITICA was tested by analyzing the available Salmonella typhimurium DNA sequences. Its predictions were compared with the DNA sequence annotations and with the predictions of GenMark. CRITICA proved to be more accurate than GenMark, and moreover, many of its predictions that would seem to be errors instead reflect problems in the sequence databases. The source code of CRITICA is freely available by anonymous FTP (rdp.life.uiuc.edu in/pub/critica) and on the World Wide Web (http:/(/)rdpwww.life.uiuc.edu).

Non-NASA Center↗

NASA Tech Briefs, May 2003

Topics covered include: Using Diffusion Bonding in Making Piezoelectric Actuators; Wireless Temperature-Monitoring System; Analog Binaural Circuits for Detecting and Locating Leaks; Mirrors Containing Biomimetic Shape-Control Actuators; Surface-Micromachined Planar Arrays of Thermopiles; Cascade Back-Propagation Learning in Neural Networks; Perovskite Superlattices as Tunable Microwave Devices; Rollable Thin-Shell Nanolaminate Mirrors; Flight Tests of a Ministick Controller in an F/A-18 Airplane; Piezoelectrically Actuated Shutter for High Vacuum; Bio-Inspired Engineering of Exploration Systems; Microscope Cells Containing Multiple Micromachined Wells; Electrophoretic Deposition for Fabricating Microbatteries; Integrated Arrays of Ion-Sensitive Electrodes; Model of Fluidized Bed Containing Reacting Solids and Gases; Membrane Mirrors With Bimorph Shape Actuators; Using Fractional Clock-Period Delays in Telemetry Arraying; Developing Generic Software for Spacecraft Avionics; Numerical Study of Pyrolysis of Biomass in Fluidized Beds; and Assessment of Models of Chemically Reacting Granular Flows.

Source record↗

Physics Based Model for Online Fault Detection in Autonomous Cryogenic Loading System

We report the progress in the development of the chilldown model for rapid cryogenic loading system developed at KSC. The nontrivial characteristic feature of the analyzed chilldown regime is its active control by dump valves. The two-phase flow model of the chilldown is approximated as one-dimensional homogeneous fluid flow with no slip condition for the interphase velocity. The model is built using commercial SINDAFLUINT software. The results of numerical predictions are in good agreement with the experimental time traces. The obtained results pave the way to the application of the SINDAFLUINT model as a verification tool for the design and algorithm development required for autonomous loading operation.

Cryogenics↗

Computational Investigation of a Boundary-Layer Ingestion Propulsion System for the Common Research Model

This thesis will examine potential propulsive and aerodynamic benefits of integrating a boundary-layer ingestion (BLI) propulsion system with a typical commercial aircraft using the Common Research Model geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment will be used to generate engine conditions for CFD analysis. Improvements to the BLI geometry will be made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.3% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from boundary-layer ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

Blumenthal, Brennan↗

Computational Investigation of a Boundary-Layer Ingesting Propulsion System for the Common Research Model

The present paper examines potential propulsive and aerodynamic benefits of integrating a Boundary-Layer Ingestion (BLI) propulsion system into a typical commercial aircraft using the Common Research Model (CRM) geometry and the NASA Tetrahedral Unstructured Software System (TetrUSS). The Numerical Propulsion System Simulation (NPSS) environment is used to generate engine conditions for CFD analysis. Improvements to the BLI geometry are made using the Constrained Direct Iterative Surface Curvature (CDISC) design method. Previous studies have shown reductions of up to 25% in terms of propulsive power required for cruise for other axisymmetric geometries using the BLI concept. An analysis of engine power requirements, drag, and lift coefficients using the baseline and BLI geometries coupled with the NPSS model are shown. Potential benefits of the BLI system relating to cruise propulsive power are quantified using a power balance method, and a comparison to the baseline case is made. Iterations of the BLI geometric design are shown and any improvements between subsequent BLI designs presented. Simulations are conducted for a cruise flight condition of Mach 0.85 at an altitude of 38,500 feet and an angle of attack of 2 deg for all geometries. A comparison between available wind tunnel data, previous computational results, and the original CRM model is presented for model verification purposes along with full results for BLI power savings. Results indicate a 14.4% reduction in engine power requirements at cruise for the BLI configuration over the baseline geometry. Minor shaping of the aft portion of the fuselage using CDISC has been shown to increase the benefit from Boundary-Layer Ingestion further, resulting in a 15.6% reduction in power requirements for cruise as well as a drag reduction of eighteen counts over the baseline geometry.

Blumenthal, Brennan T.↗

A Three-Dimensional Thermodynamically Based Function for the Progressive Failure of Unidirectional Composites

A thermodynamically-based work potential theory for modeling progressive damage for laminated, unidirectional composites assuming plane stress (2D Schaperystheory) is extended to three dimensioanl (3D). An internal state variable, S, is defined to account for the dissipated energy due to damage evolution in the form of microstructure changes in the matrix. With the stationary of the total work potential with respect to the internal state variable, a thermodynamically-consistent set of evolution equationsis derived. The internal state variable is related to the transverse and shear modulithrough microdamage functions. In the first part of this work, coupon specimensare prepared to conduct experiments to characterize the relations between the internalstate variable and the transverse modulus as well as shear modulus. The informationis subsequent used for the prediction of three point bending test. In the second partof this work, objectivity is studied. Three separate methods utilizing different definitions of a reduced internal state variable or of the order of the polynomials are used to represent the matrix micro-damage functions are employed. The three methods are implemented in a user defined subroutine within a commercial finite element method software package. Results from numerical simulations of a center-notched composites panel are compared. The agreement in the maximum stress predictions among the three methods indicates that objectivity, with respect to the functional form of themicrodamage functions, is satisfied.

carbon fiber reinforced polymer composites↗

High-Resolution Simulations of Gas-Solids Jet Penetration Into a High Density Riser Flow

High-resolution simulations of a gas-solids jet in a 0.3 m diameter and 15.9 m tall circulating fluidized bed (CFB) riser were conducted with the open source software-MFIX. In the numerical simulations, both gas and solids injected through a 1.6 cm diameter radial-directed tube 4.3 m above the bottom distributor were tracked as tracers, which enable the analysis of the characteristics of a two-phase jet. Two jetting gas velocities of 16.6 and 37.2 m/s were studied with the other operating conditions fixed. Reasonable flow hydrodynamics with respect to overall pressure drop, voidage, and solids velocity distributions were predicted. Due to the different dynamic responses of gas and particles to the crossflow, a significant separation of gas and solids within the jet region was predicted for both cases. In addition, the jet characteristics based on tracer concentration and tracer mass fraction profiles at different downstream levels are discussed. Overall, the numerical predictions compare favorably to the experimental measurements made at NETL.

42 ENGINEERING↗

TChem

The TChem toolkit is a software library that enables numerical simulations using complex chemistry and facilitates the analysis of detailed kinetic models. The toolkit provide capabilities for thermodynamic properties based on NASA polynomials and species production and consumption rates. It incorporates methods that can selectively modify reaction parameters for sensitivity analysis and uncertainty quantification. The library also contains several functions that provide analytically computed Jacobian matrices necessary for the efficient time advancement and analysis of detailed kinetic models.

Source record↗

Point Kinetics and Reactivity Feedback Modeling in SAM

Over the past few years, the rapidly rising interest in advanced nuclear reactor technology has led to an increased need for the developments and applications of advanced computational tools for modeling and simulation. System Analysis Module (SAM) is being developed at Argonne National Laboratory as a modern system-level modeling and simulation tool for advanced non-light water reactor safety analyses [1]. It utilizes the object-oriented application framework MOOSE [2] to leverage the modern software environment and advanced numerical methods [3]. To meet this need, the capabilities of SAM are being extended to enable the transient modeling, analysis, and design of advanced nuclear reactor systems. The objective of this summary is to present the development of Point-Kinetics modeling and reactivity feedback mechanisms in SAM. This summary also presents the new capability for modeling the thermal expansion reactivity feedback by coupling SAM and an external thermomechanics module (Tensor Mechanics) from MOOSE.

Hu, Guojun↗

Boundary Plasma Turbulence Simulations for Tokamaks

The boundary plasma turbulence code BOUT models tokamak boundary-plasma turbulence in a realistic divertor geometry using modified Braginskii equations for plasma vorticity, density (ni), electron and ion temperature (T{sub e}; T{sub i}) and parallel momenta. The BOUT code solves for the plasma fluid equations in a three dimensional (3D) toroidal segment (or a toroidal wedge), including the region somewhat inside the separatrix and extending into the scrape-off layer; the private flux region is also included. In this paper, a description is given of the sophisticated physical models, innovative numerical algorithms, and modern software design used to simulate edge-plasmas in magnetic fusion energy devices. The BOUT code's unique capabilities and functionality are exemplified via simulations of the impact of plasma density on tokamak edge turbulence and blob dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Numerical Modelling of Radionuclide Migration in the Context of a Near-Surface LILW Disposal Facility - 18618

The reference solution for the management of low and intermediate level short-lived waste (LILW) in France consists in their emplacement in concrete vaults built at the near-surface. The corresponding disposal facility under operation by the French waste management organization (Andra), is located in North-eastern France and planned to be closed in 2060. The safety case developed by Andra has to show the evidence that, amongst other aspects, the radionuclide transfer through the confinement barriers will occur in such a way that the human and environmental exposure will be as low as reasonably achievable (ALARA) and in accordance with the dose constraints. For this purpose, modelling is used to integrate uncertainties about the characteristics of concrete components, waste and water table and their evolution in time and space. At last, modelling is finally used to investigate the radiological impact of specific scenarios in which the failure of safety barriers occurs. In the frame of its technical review of the safety assessment, the French Institute for Radiological Protection and Nuclear Safety (IRSN) also performs such kind of numerical modelling of radionuclide fate from the waste to the hydrogeological outlets, in order to check whether the assessment performed by Andra takes into account sufficiently conservative assumptions. The present work aims to evaluate the role of components of the vaults on radionuclide transport during the post-closure period over a few thousand years. For this purpose, IRSN carries out numerical calculations with MELODIE software, which simulates water flow and transport of species, in order to simulate radionuclide migration from waste packages emplaced in a concrete vault to the surrounding groundwater. The developed transport model focuses on 3-H radionuclide and integrates Andra's main assumptions (release model from the waste packages, chemical and hydraulic properties of the vault components, shrinkage and cracks in concrete components). An adaptive mesh method, based on an a posteriori error estimator, was used to model the cracks and the consideration of a strong heterogeneity in the hydraulic and transport parameters values in the different components of the model. This method shows an improvement of results of about 40 times, whereas the mesh size was increased by only 2%. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Boundary Plasma Turbulence Simulations for Tokamaks

The boundary plasma turbulence code BOUT models tokamak boundary-plasma turbulence in a realistic divertor geometry using modified Braginskii equations for plasma vorticity, density (ni), electron and ion temperature (T{sub e}; T{sub i}) and parallel momenta. The BOUT code solves for the plasma fluid equations in a three dimensional (3D) toroidal segment (or a toroidal wedge), including the region somewhat inside the separatrix and extending into the scrape-off layer; the private flux region is also included. In this paper, a description is given of the sophisticated physical models, innovative numerical algorithms, and modern software design used to simulate edge-plasmas in magnetic fusion energy devices. The BOUT code's unique capabilities and functionality are exemplified via simulations of the impact of plasma density on tokamak edge turbulence and blob dynamics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Phenix - a comprehensive python-based system for macromolecular structure solution

Macromolecular X-ray crystallography is routinely applied to understand biological processes at a molecular level. However, significant time and effort are still required to solve and complete many of these structures because of the need for manual interpretation of complex numerical data using many software packages, and the repeated use of interactive three-dimensional graphics. Phenix has been developed to provide a comprehensive system for crystallographic structure solution with an emphasis on automation of all procedures. This has relied on the development of algorithms that minimize or eliminate subjective input, the development of algorithms that automate procedures that are traditionally performed by hand, and finally the development of a framework that allows a tight integration between the algorithms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗