SEARCH · Search NASA
Results for “Operando”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Laser, vacuum and gas reaction chamber for operando measurements at NSLS-II's 28-ID-2
We present a laser reaction chamber that we have developed for in situ/operando X-ray diffraction measurements at the NSLS-II 28-ID-2 X-ray powder diffraction beamline. This chamber allows for rapid and dynamic sample heating under specialized gas environments, spanning ambient conditions down to vacuum pressures. We demonstrate the capabilities of this setup through two applications: laser-driven heating in polycrystalline iron oxide and in single-crystal WTe 2 . Our measurements reveal the ability to resolve chemical reaction kinetics over minutes with 1 s time resolution. This setup advances opportunities for in situ/operando X-ray diffraction studies of both bulk and single-crystal materials.
Operando Investigation of the Molecular Origins of Dipole Switching in P(VDF‐TrFE‐CFE) Terpolymer for Large Adiabatic Temperature Change
Abstract Relaxor ferroelectric polymers exhibiting a giant electrocaloric effect (ECE) can potentially be used to create next‐generation solid‐state coolers. Under an electric field, poly(vinylidene fluoride‐trifluoroethylene‐chlorofluoroethylene) terpolymer goes through a large dipolar entropy change producing a high adiabatic temperature change (Δ T ECE ). This work resolves the molecular origins of the large entropy change behind the electric field‐induced dipole switching. A Fourier transform infrared spectroscopy equipped with a high voltage source is used to operandoly observe the characteristic molecular vibrational modes. A short‐range trans (T) conformation of the CF 2 ‐CH 2 dyads interrupted by a gauche (G) conformation, e.g., TTTG in the terpolymer chain, undergoes a dynamic transformation that leads to a corresponding Δ T ECE whenever an electric field is applied. The molecular dynamics simulation also proves that the energy barrier that the transformation from TTTGs into a long T sequence overcomes is smaller than that for all other conformations. A mixed solvent system is used to obtain T3G‐enriched terpolymer films exhibiting a 4.02 K Δ T ECE at 60 MV m −1 and these films are employed to manufacture a 2‐layer‐cascaded cooling device that achieves a 6.7 K temperature lift, the highest reported value for a 2‐layer cascaded device made of fluoropolymers.
Nonuniform Ionic and Electronic Transport of Ceramic and Polymer/Ceramic Hybrid Electrolyte by Nanometer-Scale Operando Imaging for Solid-State Battery
Replacing the liquid electrolyte in lithium batteries with solid-state ion conductor is promising for next-generation energy storage that is safe and has high energy density. In this work, nanometer-resolution ionic and electronic transport imaging of Li 3 PS 4 (LPS), a solid-state electrolyte (SSE), is reported. This nm resolution is achieved by using a logarithm-scale current amplifier that enhances the current sensitivity to the fA range. Large fluctuations of ion current—one to two orders of magnitude on the LPS and on the LPS region of a polymer/LPS bulk hybrid SSE—that must be mitigated to eliminate Li dendrite formation and growth, are found. This ion current fluctuation is understood in terms of highly anisotropic transport kinetic barriers along the different crystalline axes due to different grain orientations in the polycrystalline and glass ceramic materials. The results on the bulk hybrid SSE show a sharp transition of ionic and electronic transport at the LPS/polymer boundary and decreases in average ionic current with decreasing polyimine particle size and with extensive cycling. The results elucidate the mechanism of polyimine extension into interparticles to prevent Li dendrite growth. This work opens up novel characterization of charge transport, which relates to Li plating and stripping for solid-state-batteries.
In situ and operando force-based atomic force microscopy for probing local functionality in energy storage materials
Electrochemical energy storage is the key enabling component of electric vehicles and solar-/wind-based energy technologies. The enhancement of energy stored requires the detailed understanding of charge storage mechanisms and local electrochemical and electromechanical phenomena over a variety of length scales from atoms to full cells. Classical electrochemical techniques, such as voltammetry, represent the macroscopic electrochemical properties, and consequently do not allow to extract important information about local electrochemical reactions, ions adsorption, intercalations, and transport. Understanding, controlling, and tuning the local electrochemical functionalities in functional energy materials require in situ/operando techniques which limit the use of structural and functional characterization techniques that provide local information. Here, force-based atomic force microscopies (AFMs) have provided novel insights into locally probing electrochemical mechanisms on tens of nanometer and even molecular length scales and provide a viable pathway to probe electrochemical processes in situ/operando. In this review, we highlight the contributions in the development and application of force-based AFM methods to elucidate the local charge storage mechanism in a variety of energy-related materials. We will focus in particular on methods or AFM modalities in a liquid electrolyte environment.
In Operando Angle‐Resolved Photoemission Spectroscopy with Nanoscale Spatial Resolution: Spatial Mapping of the Electronic Structure of Twisted Bilayer Graphene
To pinpoint the electronic and structural mechanisms that affect intrinsic and extrinsic performance limits of 2D material devices, it is of critical importance to resolve the electronic properties on the mesoscopic length scale of such devices under operating conditions. Herein, angle‐resolved photoemission spectroscopy with nanoscale spatial resolution (nanoARPES) is used to map the quasiparticle electronic structure of a twisted bilayer graphene device. The dispersion and linewidth of the Dirac cones associated with top and bottom graphene layers are determined as a function of spatial position on the device under both static and operating conditions. The analysis reveals that microscopic rotational domains in the two graphene layers establish a range of twist angles from 9.8° to 12.7°. Application of current and electrostatic gating lead to strong electric fields with peak strengths of 0.75 V/μm at the rotational domain boundaries in the device. These proof‐of‐principle results demonstrate the potential of nanoARPES to link mesoscale structural variations with electronic states in operating device conditions and to disentangle such extrinsic factors from the intrinsic quasiparticle dispersion.
In-operando Lithium Evaporation Inducing Helium Retention in Long-Pulse HIDRA Helium Plasmas
Not provided.
Operando Converting BiOCl into Bi[subscript 2]O[subscript 2](CO[subscript 3])[subscript x]Cly for Ef
Explore the source record for details and available documents.
Operando synchrotron X-ray analysis of melt pool dynamics in an Al-Sn immiscible alloy
The melt flow in an Al-50vol.% Sn immiscible alloy, produced by single-track laser melting of Al and Sn elemental powders, was studied in real time. High-speed synchrotron X-ray imaging was used to track Al and Sn liquids’ movements, and also to examine elemental distributions in the laser tracks, complimented by electron microscopy after solidification. Key aspects, including melt pool geometry, keyhole instability, and flow dynamics (flow pattern and velocity), were examined using digital image analysis. Relatively deeper melt pools formed at 400 W and 300 mm/s exhibited greater stability, with smooth surfaces, consistent outward flow, and minor vortices near the keyhole. In contrast, shallower pools produced at higher scanning speeds (>500 mm/s) demonstrated greater instability with increased surface waviness, and stronger velocity fluctuations, leading to numerous micro-vortices and increased Al-Sn heterogeneity. Velocity scale estimations, supported by experimental observations, examined the roles of vapour pressure, Marangoni effect, buoyancy, inertial, and surface tension forces in the flow. The results revealed that vapour pressure and mechanical waves dominated at high scanning speeds (shallow pools), while Marangoni forces were equally significant in deep pools at lower speeds (300 mm/s). Buoyancy was found to have minimal impact in both cases. Furthermore, the interaction between inertial and surface tension forces played a critical role in determining the degree of waviness of the pools’ surfaces. These findings offer valuable insights into melt pool dynamics during laser processing of immiscible alloys and other metallic systems using elemental powders, and provide guidance for developing high-fidelity computational fluid dynamics models.
Estimating the energy requirement for hydrogen production in proton exchange membrane electrolysis cells using rapid operando hydrogen crossover analysis
Hydrogen (H 2 ) crossover in proton exchange membrane water electrolyzers refers to the process by which hydrogen produced at the cathode traverses the membrane and mixes with the oxygen produced at the anode. This phenomenon reduces efficiency and may pose flammability hazards. In this work we present a method for quantifying the H 2 content of the anode exhaust gas using a gas chromatograph that is capable of sampling data every 2 min. Subsequent theory is presented to calculate the crossover flux, overall H 2 efficiency, and H 2 energy requirements. Results the effects of membrane thickness using Nafion TM N117 (178 um) and Nafion TM NR212 (51 um) membranes. Furthermore, it was found that thinner membranes lead to improved VI performance but exhibit higher crossover rates. Despite their increased crossover, leading to decreased hydrogen efficiency, the calculated required energy for NR212 membrane-electrode assemblies (MEAs) was significantly lower than that of N117 MEAs.
X-ray observation of individual Ti-6Al-4V spherical powder particle impact in an in-situ operando laser directed energy deposition system
Understanding the particle capture mechanism in the laser directed energy deposition additive manufacturing process provides a foundation for improving productivity and reducing material loss. Capturing this phenomenon is challenging due to its highly transient time interval. To analyze the impact behavior of spherical Ti-6Al-4V powder, a custom laser directed energy deposition system was designed to control the deposition of individual particles. Synchrotron X-ray imaging at 24 kHz monitored the impact dynamics of individual powder particles. A multi-physics model based on the Smoothed-Particle Hydrodynamics scheme supported the analysis by providing the temperature and velocity fields of the molten pool. Results revealed that in laser directed energy deposition, surface tension forces dominated the powder–molten pool interaction. Hydrophobic Ti-6Al-4V powder particles had an equilibrium contact angle of 121 degrees with their molten state. Furthermore, Ti-6Al-4V powder particles required a high impact velocity (6 to 12 m/s) to transition from oscillation to submergence behavior. Lastly, oscillating powder particles that impacted near the location of the laser beam exhibited faster melting, highlighting the contribution of the laser beam to the melting mechanism. This work lays the foundation for investigations of powder particle impact in laser directed deposition and supports the validation of numerical models of powder–molten pool interactions.
Peering into Batteries: Electrochemical Insight Through In Situ and Operando Methods over Multiple Length Scales
Not Available
Operando spatial mapping of lithium concentration using thermal-wave sensing
Not Available
In-situ and in-operando analysis of voltage losses using sense wires for proton exchange membrane water electrolyzers
Proton exchange membrane water electrolyzer development requires understanding processes at the materials and interface levels to reach the required performance and lifetime targets for increasing market penetration. To achieve the required progress, it is critical to develop advanced in-situ diagnostics that allow observation of the changes that come with the reduction of catalyst loading combined with long-term intermittent operation. This work presents an internal voltage sensing method that enables observing internal voltage drops in an operating electrolyzer cell. It allows the total cell resistance to be separated into anode, CCM, and cathode resistance. The method is demonstrated by operating cells with different anode porous transport layers (PTLs). The changing properties of the PTLs result in significant variations of the resistances. Enhancing the PTL properties with a protective coating reduces the anode resistance significantly. In addition to these observations, the method enables a real-time monitoring of resistance related values that impact performance in water electrolyzers. Long-term experiments with the method allow us to gain insights into processes that occur during operation such as conditioning or degradation. The internal voltage sensing method presented in this study is a novel technique for diagnosing, analyzing, and optimizing water electrolyzers and other energy conversion devices.
Spatially-resolved lithiation dynamics from operando X-ray diffraction and electrochemical modeling of lithium-ion cells
In this study, energy dispersive X-ray diffraction is used to profile the time evolution of ordered Li x C 6 phases in solid electrodes of lithium-ion cells charged at rates between 0.2 and 4.7C (where 1C corresponds to full discharge in 1 h). The methods for quantifying lithium concentration in these phases from the acquired diffraction patterns are described. Compact expressions for time-dependent concentration gradients in the solid electrodes using orthogonal polynomial expansions are presented. Experimentally, these gradients persisted in lithiated graphite electrodes even after the cells rested at open-circuit for over 9 h. A multiphase electrochemical model of graphite intercalation captured many of the observed behaviors, including the progression of phase transitions and the persistent gradients at zero current. However, the magnitude of concentration gradients in both the oxide cathode and graphite anode is underestimated by the model, even at moderate currents.
Operando analysis of the positive active mass of lead batteries by neutron diffraction
Not Available