Search NASA⌕ Search

SEARCH · Search NASA

Results for “Oxide reducibility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Condensation of nonequilibrium phases of refractory silicates from the vapor

Silicon monoxide solid was evaporated in a bell jar containing reducing, neutral, or oxidizing atmospheres at pressures of a few torr. The vapor invariably condensed as smoke-sized particles of silicon sesquioxide, Si2O3. The condensation of a solid whose composition differs from that of the parent gas and is apparently the least stable of the three solid species illustrates the importance of specific nucleation effects in the condensation process. This result has significant implications for theories of formation of grains in space.

Day, K. L.↗
NASA NTRS1981

Effect of Yttria additives on properties of pressureless-sintered silicon nitride

Si3N4-base ceramics were made from milled Si3N4 containing 11.1 wt% SiO2 and oxide additives by pressureless sintering at 1760 C. The four-point-average moduli of rupture were 460, 515, and 515 MPa at room temperature and 270, 256, and 227 MPa at 1400 C for compositions with 3.67, 7.22, and 14.0 wt% Y2O3, respectively. The oxidation resistance of these compositions decreased with increasing Y2O3 in the 600 to 1400 C range, and no surface oxide cracking or spalling was noted. Partial substitution of Al2O3 for Y2O3 reduced both strength and oxidation resistance.

Arias, A.↗
NASA NTRS1982

UV radiation from the young sun and oxygen and ozone levels in the prebiological palaeoatmosphere

UV measurements of young T-Tauri stars, resembling the sun at an age of a few million years, have recently been made with the International Ultraviolet Explorer. They indicate that young stars emit up to 10,000 times more UV than the present sun. The implications for the origin and evolution of O2 and O3 in the prebiological palaeoatmosphere are presented here. The results of photochemical calculations indicate that the O2 surface mixing ratio was a factor 10,000-1,000,000 times greater than the standard value of 10 to the -15. This new value reconciles the simultaneous existence of oxidized iron and reduced uranium.

Canuto, V. M.↗
NASA NTRS1984

Orbiting dynamic compression laboratory

In order to examine the feasibility of carrying out dynamic compression experiments on a space station, the possibility of using explosive gun launchers is studied. The question of whether powders of a refractory metal (molybdenum) and a metallic glass could be well considered by dynamic compression is examined. In both cases extremely good bonds are obtained between grains of metal and metallic glass at 180 and 80 kb, respectively. When the oxide surface is reduced and the dynamic consolidation is carried out in vacuum, in the case of molybdenum, tensile tests of the recovered samples demonstrated beneficial ultimate tensile strengths.

Ahrens, T. J.↗
NASA NTRS1986

Tensile behavior of Fe-40Al alloys with B and Zr additions

Both Fe-40Al and Fe-40Al-0.1Zr with and without B were produced by the hot extrusion of powdered metal. Tensile properties were determined from room temperature to 1100 K in air. All of the materials possessed some ductility at room temperature, and addition of B caused an increase in ductility and a change in fracture mode from intergranular to transgranular cleavage. At high temperatures, failure was caused primarily by the formation of grain boundary cavities in all of the alloys. The effect of Zr addition was unclear because of the complexity of the various microstructures. Comparison of air and vacuum testing at high temperatures revealed that an apparent oxidation assisted mechanism reduced high temperature ductility in these alloys, especially at 900 K.

Gaydosh, D. J.↗
NASA NTRS1986

Thioredoxins in evolutionarily primitive organisms

Thioredoxins are low molecular weight redox proteins, alternating between the S-S (oxidized) and SH (reduced) states, that function in a number of biochemical processes, including DNA synthesis, DNA replication, and enzyme regulation. Until recently, reduced ferredoxin was known to serve as the source of reducing power for the reduction of thioredoxins only in oxygenic photosynthetic cells. In all other organisms, the source of hydrogen (electrons) for thioredoxin reduction was considered to be NADPH. It was found that Clostridium pasteurianum, an anaerobic organism normally living in the soil unexposed to light, resembles photosynthetic cells in using ferredoxin for the reduction of thioredoxin. The results reveal the existence of a pathway in which ferredoxin, provides the reducing power for the reduction of thioredoxin via the flavoprotein enzyme, ferredoxinthioredoxin reductase. In related studies, it was found that Chromatium vinosum, an anaerobic photosynthetic purple sulfur bacterium, resembles evolutionarily more advanced micro-organisms in having an NADP-thioredoxin system composed of a single thioredoxin which is reduced by NADPH via NADP-thioredoxin reductase. The adoption of the NADP-thioredoxin system by Chromatium seems appropriate in view of evidence tha the organi sm utilizes ATP-driven reverse electron transport. Finally, results of research directed towards the identification of target enzymes of the ferredoxin/thioredoxin system in a cyanobacterium (Nostoc muscorum), show that thioredoxin-linked photosynthetic enzymes of cyanobateria are similar to those of chloroplasts. It now seems that the ferredoxin/thioredoxin system functions in regulating CO2 assimilation via the reductive pentose phosphate cycle in oxygenic but not anoxygenic photosynthetic cells.

Buchanan, B. B.↗
NASA NTRS1988

Proterozoic Bushveld-Vredefort catastrophe: Possible causes and consequences

Bushveld Complex and Vredefort Dome are unique features, formed in close proximity during the same time interval, approximately 2 Ga. Both show evidence of catastrophic events in the shallow marine environment of the otherwise stable Kaapvaal Craton. Explanation by multiple impacts of an asteroid, brecciated by an inter-asteroidal collision and disintegrating in Earth's gravity field is supported by pseudotachylite, shatter cones, coesite, and stishovite at Vredefort but these shock phenomena were not found in the Bushveld Complex. The Bushveld Complex was formerly interpreted as a lopolith, a view incompatible with gravity, electrical resistivity, magnetic, and seismic-reflection data. It is outlined by five inward-dipping lobes of layered ultramafic-mafic plutonic rocks that partly coalesce to form a basin-like feature 400 km in diameter and 65,000 sq. km. in area, equivalent to a small lunar mare. The Bushveld Complex is orders of magnitudes larger than other proposed terrestrial impact structures and differs from them in important ways. Its principal members, in order of age, are Rooiberg Felsite, RLS, and Lebowa Granite. The Bushveld-Vredefort events occurred during the interval from neutral or reducing atmosphere to oxidizing atmosphere. This transition is usually related to the evolution of photosynthesizing organisms. If the impact hypothesis for Bushveld-Vredefort can be confirmed, it may represent a global catastrophe sufficient to contribute to environmental changes favoring aerobic photosynthesizing eukaryotes over anaerobic prokaryotes.

Elston, W. E.↗
NASA NTRS1989

A new test machine for measuring friction and wear in controlled atmospheres to 1200 C

This paper describes a new high temperature friction and wear test apparatus (tribometer) at NASA Lewis Research Center, Cleveland, Ohio. The tribometer can be used as a pin-on-disk or pin-on-ring configuration and is specially designed to measure the tribological properties of ceramics and high temperature metallic alloys from room temperature to 1200 C. Sliding mode can be selected to be either unidirectional at velocities up to 22 m/sec or oscillating at frequencies up 4.5 Hz and amplitudes up to + or - 60 deg. The test atmosphere is established by a controlled flow rate of a purge gas. All components within the test chamber are compatible with oxidizing, inert, or reducing gases.

Sliney, Harold E.↗
NASA NTRS1990

Heat treatment study of the SiC/Ti-15-3 composite system

The oxidation and aging behaviors of a continuous fiber SiC/Ti-15V-3Cr-3Sn-3Al composite (SiC/Ti-15-3) were investigated. The aging characteristic of the composite were compared with those of the unreinforced Ti-15-3 matrix material, which was processed in the same manner as the composite. Various age hardened conditions of both the unreinforced matrix and the composite were evaluated by using optical microscopy, hardness measurements, and room temperature tensile tests (unreinforced matrix only). The Ti-15-3 material formed a thick surface oxide at temperature at or above 550 C when heat treated in air. The in situ composite matrix was softer than the unreinforced matrix for equivalent aging conditions. Both materials hardened to a maximum, then softened during overaging. The temperature at which peak aging occurred was approx. 450 C for both the in situ composite matrix and the unreinforced matrix. The room temperature elastic modulus and ultimate tensile strength of the unreinforced matrix varied as a function of aging treatment and paralleled the hardness behavior. The modulus and tensile strength showed little response to aging up to temperatures of 300 C; however, these properties increased after aging at 550 C. Aging at temperatures above 550 C resulted in a decrease in the modulus and tensile strength. The failure strain was a function of the precipitation state and of the amount of oxidation resulting from the heat treatment. Aging in air at the higher temperatures (greater than 550 C) caused the formation of a thick oxide layer and reduced the ductility. Aging in vacuum at these temperatures resulted in significantly higher ductilities. Long term exposures at 700 C caused the formation of a large grain boundary alpha-phase which reduced the ductility, even though the specimens were heat treated in vacuum.

Lerch, Bradley A.↗
NASA NTRS1991

Production of oxygen from lunar ilmenite

The kinetics and the mechanism of reduction of synthetic ilmenite by hydrogen in the temperature range of 807 to 1014 C were investigated. At temperatures below 876 C, the temporal profiles of conversion have a sigmoidal shape and indicate the presence of three different stages (induction, acceleration, and deceleration) during the reduction reaction. The apparent activation energy for the reaction is 22.3 kcal/mole, whereas the intrinsic activation energy is 16.9 kcal/mole. Scanning electron microscopy and energy dispersive x-ray analyses show that the diffusion of Fe product away from the reaction front and through the TiO2 phase, followed by the nucleation and growth of a separate Fe phase is an important step affecting the process kinetics. X-ray diffraction and wavelength dispersive x-ray results indicate that the TiO2 can be reduced to lower oxides of titanium at temperatures higher than 876 C.

Shadman, F.↗
NASA NTRS1991

Magma Electrolysis: An update

Electrolytic extraction of O2 from molten lunar soil is conceptually simple and thus a candidate process for producing O2 on the Moon. Possible container and electrode materials are being tested for durability in corrosive high-temperature silicate melts and looking for complications that might increase energy requirements. Gaseous oxygen is being produced by electrolysis of 1-2 gram quantities of silicate melts in spinel (MgAl2O4) crucibles; in these melts, spinel is a stable phase. The concentration of FeO was kept low because FeO decrease O2 production efficiency. Platinum electrodes were placed about 0.5 cm apart in the melt. The spinel crucible was still intact after 40 minutes of electrolysis, when the experiment was halted for examination. The Pt anode was also intact; its Pt was maintained in a dynamci state in which the anode was continuously oxidized but quickly reduced again by the silicate melt, inhibiting migration of Pt away from the anode. In melts with low concentrations of Al2O3 + SiO2 (2 wt percent), the energy of resistance heating was only approximately equal to 10 to 20 percent of the theoretical amount required to produce O2. In melts substantially more concentrated in Al2O3 + SiO2, higher melt viscosity resulted in frothing that, in the worst case, caused high enough melt resistivities to raise the energy requirements to nearly 10 times theoretical. Both Fe and Si are produced at the cathode; in iron-rich melts, a- and c-iron and molten ferrosilicon were observed. Production was also observed at the cathode of a previously unrecognized gas; which is not yet identified. The solubility of metallic species was measured in silicate melts. They are too low to reduce significantly the efficiency of O2 production.

Colson, Russell O.↗
NASA NTRS1991

A new test machine for measuring friction and wear in controlled atmospheres to 1200 C

This paper describes a new high-temperature friction and wear test apparatus (tribometer). The tribometer can be used as a pin-on-disk or pin-on-ring configuration and is specially designed to measure the tribological properties of ceramics and high temperature metallic alloys from room temperature to 1200 C. Sliding mode can be selected to be either unidirectional at velocities up to 22 m/sec or oscillating at frequencies up to 4.6 Hz and amplitudes up to + or - 60 deg. The test atmosphere is established by a controlled flow rate of a purge gas. All components within the test chamber are compatible with oxidizing, inert or reducing gases.

Sliney, Harold E.↗
NASA NTRS1991

The SiH vibrational stretch as an indicator of the chemical state of interstellar grains

The infrared spectra of amorphous silicate grains and films formed in a variety of laboratory experiments have been measured. It is found that the frequency of the SiH fundamental stretch is extremely sensitive to the chemical environment of the grain in which the silicon is bound and varies from 2270/cm in oxidized grains to 2110/cm in a reducing environment. It is proposed that features previously observed in W33A could be due to -SiH groups in amorphous silica, partially reduced silica, silicon nitride or slightly oxidized silicon carbide. It is predicted that observations at 2270/cm will reveal a feature due to -SiH groups in highly oxidized interstelar and circumstellar grains. Such a feature might also appear in the spectra of comets.

Moore, Marla H.↗
NASA NTRS1991

Critical technology experiment results for lightweight space heat receiver

Critical technology experiments have been performed on thermal energy storage modules in support of the NASA Advanced Solar Dynamic Brayton Heat Receiver Program. The modules, wedge-shaped canisters containing lithium fluoride (LiF), were designed to minimize the mechanical stresses that occur during the phase change of the LiF. Nickel foam inserts were placed in two of the test canisters to provide thermal conductivity enhancement and to distribute the void volume throughout the canister. A procedure was developed for reducing the nickel oxides on the nickel foam to enhance the wicking ability of the foam. The canisters were filled with LiF and closure-welded at the NASA Lewis Research Center. Two canisters, one with a nickel foam insert, the other without an insert, were thermally cycled in various orientations in a fluidized bed furnace. Computer-aided tomography was successfully used to nondestructively determine void locations in the canisters. Finally, canister dimensional stability was measured after thermal cycling with an inspection fixture.

Schneider, Michael G.↗
NASA NTRS1997

New Anti-Corrosive Coatings with Resin-Bonded Polyaniline and Related Electroactive Groups

It is already known that polyaniline (an electroactive polymer) functions as a corrosion inhibitor for steel and in view of the fact that it is known to perform in the presence of hydrochloric acid, it has been considered likely that it may be useful to NASA for protecting launch structures at KSC which are exposed to not only continual ocean-side salt spray but also to hydrochloric acid at the times that solid-fuel boosters are fired. The currently used zinc-rich silicate-bonded coating is not wholly protective against the hydrochloric acid. Water pollution from zinc salts is another concern. Other earlier and concurrent NASA sponsored projects have been focussed on polyaniline specifically. Our project, administered for NASA by Dr. K. Thompson of KSC and these more-specifically polyaniline-related projects are included in a CRADA coordinated by Dr. F. Via of Akzo Nobel. A parallel project at Polytechnic under Prof K. Levon concentrated more specifically on polyaniline with various dopants. Our exploratory project reported herein was aimed at broadening the range of such corrosion inhibitors, to give protective paint compounders a wider latitude for adding corrosion inhibitors having polyaniline-like performance, and thus we diverged in several probing directions from polyaniline. Our working hypothesis was that physical variants of polyaniline, such as supported formulations on pigments or carriers, and chemical variants of polyaniline, including those having no electroconductive character, may have enhanced anticorrosion activity. We also hypothesized that small (non-polymeric) molecules having structures related to those occurring in polyaniline, may be active as corrosion inhibitors. We did preliminary testing, using an ASTM salt spray method at a nearby commercial paint testing laboratory. Our most interesting findings were that a non-electroconductive meta-isomer of polyaniline showed some corrosion activity, suggesting that the features of the polyaniline molecule associated with conductivity are not necessary for the anticorrosion action. Also, signtficantly, small molecular weight aromatic diamines and diimines resembling the reduced and the oxidized repeating unit in polyaniline showed an interesting degree of anticorrosive activity, suggesting that the polymeric feature of polyaniline is not necessary for anticorrosion action.

Weil, Edward D.↗
NASA NTRS1995

A Novel Denitrifying Extreme Halophile That Grows in a Simple Mineral Salts Medium

An extremely halophilic bacterium (strain CH-1) was isolated from a saltern adjacent to San Francisco Bay. It grew in a mineral salts medium with ammonium and glucose as sole sources of nitrogen and carbon as well as energy, respectively Cells lysed at less than 10% NaCl and growth was most rapid in medium containing 20% NaCl. Cells were pieomorphic ranging from disc to ovoid-shaved and used a variety of carbohydrates as sole carbon sources. the utilization of certain carbon sources was controlled by temperature with some used at 37 degrees but not 45 C. CH-1 grew between 30 degrees and 50 C with the optimum at 45 C in the presence of 20% NaCl. CH-1 contained 2,3-di-O-isoprenyl glcerol diethers and was sensitive to aphidicofin. The major polar lipid was glucosyl-mannosyl-alucosyl diether, which is diagnostic of the Haloarcula. Thus CH-1 is an extreme halophile and a member of this genus. Among the novel characteristics of this organism was its ability to grow anaerobically in synthetic medium when nitrate was present which was only reduced to nitrous oxide. This organism should prove useful for studying denitrification and carbohydrate metabolism in the extreme halophiles; and to be a valuable resource for generic studies.

Hochstein, L. I.↗
NASA NTRS2001

Cutaneous interstitial nitric oxide concentration does not increase during heat stress in humans

Inhibition of cutaneous nitric oxide (NO) synthase reduces the magnitude of cutaneous vasodilation during whole body heating in humans. However, this observation is insufficient to conclude that NO concentration increases in the skin during a heat stress. This study was designed to test the hypothesis that whole body heating increases cutaneous interstitial NO concentration. This was accomplished by placing 2 microdialysis membranes in the forearm dermal space of 12 subjects. Both membranes were perfused with lactated Ringer solutions at a rate of 2 microl/min. In both normothermia and during whole body heating via a water perfused suit, dialysate from these membranes were obtained and analyzed for NO using the chemiluminescence technique. In six of these subjects, after the heat stress, the membranes were perfused with a 1 M solution of acetylcholine to stimulate NO release. Dialysate from these trials was also assayed to quantify cutaneous interstitial NO concentration. Whole body heating increased skin temperature from 34.6 +/- 0.2 to 38.8 +/- 0.2 degrees C (P < 0.05), which increased sublingual temperature (36.4 +/- 0.1 to 37.6 +/- 0.1 degrees C; P < 0.05), heart rate (63 +/- 5 to 93 +/- 5 beats/min; P < 0.05), and skin blood flow over the membranes (21 +/- 4 to 88 +/- 10 perfusion units; P < 0.05). NO concentration in the dialysate did not increase significantly during of the heat stress (7.6 +/- 0.7 to 8.6 +/- 0.8 microM; P > 0.05). After the heat stress, administration of acetylcholine in the perfusate significantly increased skin blood flow (128 +/- 6 perfusion units) relative to both normothermic and heat stress values and significantly increased NO concentration in the dialysate (15.8 +/- 2.4 microM). These data suggest that whole body heating does not increase cutaneous interstitial NO concentration in forearm skin. Rather, NO may serve in a permissive role in facilitating the effects of an unknown neurotransmitter, leading to cutaneous vasodilation during a heat stress.

Non-NASA Center↗
NASA NTRS2003

Nanotechnology Investigated for Future Gelled and Metallized Gelled Fuels

The objective of this research is to create combustion data for gelled and metallized gelled fuels using unique nanometer-sized gellant particles and/or nanometer-sized aluminum particles. Researchers at the NASA Glenn Research Center are formulating the fuels for both gas turbine and pulsed detonation engines. We intend to demonstrate metallized gelled fuel ignition characteristics for pulse detonation engines with JP/aluminum fuel and for gas turbine engines with gelled JP, propane, and methane fuel. The fuels to be created are revolutionary as they will deliver the highest theoretically maximum performance of gelled and metallized gelled fuels. Past combustion work has used micrometer-sized particles, which have limited the combustion performance of gelled and metallized gelled fuels. The new fuel used nanometer-sized aluminum oxide particles, which reduce the losses due to mismatch in the gas and solid phases in the exhaust. Gelled fuels provide higher density, added safety, reduced fuel slosh, reduced leakage, and increased exhaust velocity. Altogether, these benefits reduce the overall size and mass of the vehicle, increasing its flexibility.

Palaszewski, Bryan A.↗