Search NASA⌕ Search

SEARCH · Search NASA

Results for “PERFORMANCE PREDICTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 253 records · Page 14
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Predicting spacecraft multilayer insulation performance from heat transfer measurements

Multilayer insulation (MLI) ideally consists of a series of radiation shields with low-conductivity spacers. When MLI blankets were installed on cryogenic tanks or spacecraft, a large discrepancy between the calorimeter measurements and the performance of the installed blankets was discovered. It was found that discontinuities such as exposed edges coupled with high lateral heat transfer created 'heat leaks' which overshadowed the basic heat transfer of the insulation. Approaches leading to improved performance predictions of MLI units are discussed.

Stimpson, L. D.↗
NASA NTRS1973

Experimental quiet engine program. Predicted engine performance

Three turbofan configurations, each incorporating alternative noise reduction features, were tested under the Quiet Engine Program. Performance data for these engines are shown over a range of flight conditions. The data are presented in tabular form for standard day flight inlet conditions. Procedures for estimating nonstandard day performance are shown. Tabular data and calculation procedures to allow determination of ram recovery, customer bleed, and customer shaft power extraction effects on engine performance can be found in the original Performance Brochure titled, Experimental Quiet Engine Program, Predicted Engine Performance, dated April 8, 1970. Predicted engine noise levels for representative take-off and approach conditions are provided.

Source record↗
NASA NTRS1989

Predicted and preliminary evaluation of the X-ray performance of the AXAF Technology Mirror Assembly

The fabrication of the Technology Mirror Assembly (TMA) is complete, and performance predictions were made based upon mechanical and visible light measurements of the surface properties. An X-ray calibration program has been executed, and a preliminary analysis of a portion of the data is presented. The X-ray image distribution results are in reasonable agreement with the performance predictions which were calculated prior the start of the X-ray tests. The measured X-ray imaging performance approaches that expected for the Advanced X-ray Astrophysics Facility (AXAF).

Van Speybroeck, Leon↗
NASA NTRS1981

Characterization, performance, and prediction of a lead-acid battery under simulated electric vehicle driving requirements

A state-of-the-art 6-V battery module in current use by the electric vehicle industry was tested at the NASA Lewis Research Center to determine its performance characteristics under the SAE J227a driving schedules B, C, and D. The primary objective of the tests was to determine the effects of periods of recuperation and long and short periods of electrical regeneration in improving the performance of the battery module and hence extendng the vehicle range. A secondary objective was to formulate a computer program that would predict the performance of this battery module for the above driving schedules. The results show excellent correlation between the laboratory tests and predicted results. The predicted performance compared with laboratory tests was within +2.4 to -3.7 percent for the D schedule, +0.5 to -7.1 percent for the C schedule, and better than -11.4 percent for the B schedule.

Ewashinka, J. G.↗
NASA NTRS1979

Predicting dynamic performance limits for servosystems with saturating nonlinearities

A generalized treatment for a system with a single saturating nonlinearity is presented and compared with frequency response plots obtained from an analog model of the system. Once the amplitude dynamics are predicted with the limit lines, an iterative technique is employed to determine the system phase response. The saturation limit line technique is used in conjunction with velocity and acceleration limits to predict the performance of an electro-hydraulic servosystem containing a single-stage servovalve. Good agreement was obtained between predicted performance and experimental data.

Webb, J. A., Jr.↗
NASA NTRS1983

A method of predicting the performance deterioration of a compressor cascade due to sand erosion

Performance deterioration due to sand erosion is a well known phenomena for aircraft engines operating in particulate flow environments. A method for predicting this performance deterioration is developed and applied to a two dimensional compressor cascade. The locations of the particles impacts are computed by analyzing the trajectories of the individual particles. From this analysis, the material removed, the changes in the airfoil shape, and the roughness development over the surface are estimated as a function of time. The resulting airfoil profiles are analyzed for predicting performance by using an inviscid-viscous interaction technique. The analytical solution is compared with experimental results.

Balan, C.↗
NASA NTRS2021

Assessment of M2020 Terrain Relative Landing Accuracy: Flight Performance vs Predicts

Terrain Relative Navigation (TRN) was a critical enabling Entry, Descent, and Landing (EDL) technology that enabled Mars 2020 mission Perseverance rover to land at Jezero crater. TRN pro-vides real-time, autonomous, map-relative position determination and generates a landing target based on a priori knowledge of hazards. The required performance for TRN was to land within 60m of the selected target. The required 60m was sub-allocated to various error sources in three major categories: targeting error, knowledge error, and control error. The targeting error is the error in selecting an appropriate landing target and the knowledge of the target on the surface. It includes the Lander Vision System (LVS) position localization with respect the ground, the synchronization between the Lander Vision System measurement and the main Navigation filter, and errors associated with the LVS Reference Map and Safe Target Selec-tion (STS). The knowledge error is the contribution of knowledge growth from the synchronization with LVS to touchdown. The control error encompasses how accurately the system could stay on the desired reference trajectory. The TRN error budget uses a combination of analysis, simulation, and hardware test-ing results to bound the various error contributions obtained during the verification and validation process. This paper first presents a description the TRN system, focusing on the architecture of LVS and STS. The paper then gives detailed overview of the TRN error budget, with a description of the major error contribu-tions in each of the three categories. Next, the paper gives the results for three versions of the error budget, pre-launch, in-flight pre-landing, and post-landing. The paper compares the pre-flight analysis, the pre-landing analysis using in-flight data during cruise, to the post-landing analysis of the TRN performance. Pre-landing analysis best estimate of the landing performance was 33m, compared to the 60m require-ment. Post-landing analysis estimated a landing accuracy of 8.53m or better, much better than the 33m pre-landing estimate. The actual post-landing imagery calculated the distance of the rover to the targeted location to be 5m. The post-landing analysis closely bounds the image-based assessment of landing accu-racy, indicating the success of the error budget architecture in bounding the landing accuracy, as well as the fidelity of the simulations used to model and predict performance.

Chen, Allen↗
NASA NTRS1982

STGSTK: A computer code for predicting multistage axial flow compressor performance by a meanline stage stacking method

A FORTRAN computer code is presented for off-design performance prediction of axial-flow compressors. Stage and compressor performance is obtained by a stage-stacking method that uses representative velocity diagrams at rotor inlet and outlet meanline radii. The code has options for: (1) direct user input or calculation of nondimensional stage characteristics; (2) adjustment of stage characteristics for off-design speed and blade setting angle; (3) adjustment of rotor deviation angle for off-design conditions; and (4) SI or U.S. customary units. Correlations from experimental data are used to model real flow conditions. Calculations are compared with experimental data.

Steinke, R. J.↗
NASA NTRS1992

Rotary engine performance limits predicted by a zero-dimensional model

A parametric study was performed to determine the performance limits of a rotary combustion engine. This study shows how well increasing the combustion rate, insulating, and turbocharging increase brake power and decrease fuel consumption. Several generalizations can be made from the findings. First, it was shown that the fastest combustion rate is not necessarily the best combustion rate. Second, several engine insulation schemes were employed for a turbocharged engine. Performance improved only for a highly insulated engine. Finally, the variability of turbocompounding and the influence of exhaust port shape were calculated. Rotary engines performance was predicted by an improved zero-dimensional computer model based on a model developed at the Massachusetts Institute of Technology in the 1980's. Independent variables in the study include turbocharging, manifold pressures, wall thermal properties, leakage area, and exhaust port geometry. Additions to the computer programs since its results were last published include turbocharging, manifold modeling, and improved friction power loss calculation. The baseline engine for this study is a single rotor 650 cc direct-injection stratified-charge engine with aluminum housings and a stainless steel rotor. Engine maps are provided for the baseline and turbocharged versions of the engine.

Bartrand, Timothy A.↗
NASA NTRSDate not supplied

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

vaned diffuser↗
NASA NTRSDate not supplied

Experimental and Numerical Investigation of the NASA High Efficiency Centrifugal Compressor Vaned Stage Geometry and Aerodynamic Performance

Since its inception in the early 2010s, the NASA High Efficiency Centrifugal Compressor (HECC) has been enigmatic for the propulsion research community: experimental data and numerical simulations of the stage have generally not aligned in their quantifications of performance metrics. Typically, the fault for these disagreements is assigned to the numerical simulations as the simulations are models, and models are inherently incomplete representations of the experiment. This “incompleteness” may manifest in assumptions regarding roughness or heat transfer, simplifications of the flow path (i.e., neglecting bleed flows), or the oft-scapegoated turbulence model. In the case of HECC, recent work showed unexpected discrepancies between the intended impeller geometry defined in the design report (termed Design-Intent) and the manufactured impeller used in the experimental campaigns (termed As-Manufactured). That work used numerical simulations to establish that the geometric differences between the Design-Intent and As-Manufactured impellers were significant enough to result in drastically different performance predictions for the HECC vaneless diffuser configuration. The Design-Intent impeller simulations over predicted the performance relative to the experiment, whereas the As-Manufactured simulations better represented the experimental data, both in terms of one-dimensional performance metrics and spanwise flow profiles. This effort expands on that work by examining in detail the geometry and aerodynamic performance of the HECC vaned diffuser configuration. Further differences between the Design-Intent and As-Manufactured geometries have been discovered in the vaned diffuser and exit guide vanes, and these differences are documented herein. The summations of the geometric differences for all of the components were used to create two numerical models of HECC vaned diffuser configuration: the Design-Intent simulations which are generated from the original geometry definitions given in the design report and the As-Manufactured simulations which are the best available representation of the manufactured compressor hardware used in the experimental test campaigns. In congruence with the earlier vaneless diffuser work, the numerical predictions of the Design-Intent choked mass flow rate, total pressure ratio, and efficiency were notably greater than that of the As-Manufactured simulations. To increase confidence in the experimental dataset, measurements from a recent test campaign conducted in 2024 are used to validate the original experimental data acquired from 2012 to 2014 with good repeatability overall, especially considering the passage of time and differences in the data acquisition systems between the test campaigns. Both numerical simulations were then extensively evaluated against the experimental data. The As-Manufactured simulations provided better estimates of the stage performance than the Design-Intent cases in terms of most performance metrics. Nonetheless, more detailed results still show opportunities for improvement. Despite a more accurate representation of the physical hardware, characterization of the impeller work input remains a challenge even for rigorously developed numerical models.

centrifugal compressor↗
NASA NTRS1998

SPARCLE: Validation of Observing System Simulations (SPace Readiness Coherent Lidar Experiment)

NASA recently approved a mission to fly a Doppler Wind Lidar (DWL) on a U.S. Space Shuttle. SPARCLE, managed by Marshall Space Flight Center in Huntsville, AL, is targeted for launch in March 2001. This mission is viewed as a necessary demonstration of a solid state (2 micron) lidar using coherent detection before committing resources to a 3-5 year research or operational mission. While, to many, this shuttle mission is seen as the first step in a series leading to a fully operational wind observing system, to others, it is a chance to validate predictions of performance based upon theoretical models, analyses of airborne and ground-based data, and sophisticated observing system simulation experiments. This paper will be presented in two parts: first a brief overview of the SPARCLE mission and second, a summary of current performance predictions and key contributions from ground- based and airborne DWL research. The SPARCLE instrument is a 100 mJ, 6 Hz, diode-pumped 2-micron laser with a .25 m telescope using heterodyne mixing in a fiber and an InGaAs detector. A 25 cm silicon wedge scanner will be used in step-stare modes with dwells ranging from 60 seconds to .5 seconds. Pointing knowledge is achieved with a dedicated GPS/INS mounted close to the lidar. NASA's Hitchhiker program is providing the instrument enclosures (2 cans) and mission logistics support. An on-board data system is sized to record 150 Gbytes of raw signal from a two 400 MHZ A/D converters. On-board signal processing will be used to control the frequency of the Local Oscillator. SPARCLE is predicted to have a single shot backscatter sensitivity near 1x10(exp -6) m-1 sr-1, To achieve higher sensitivity, shot accumulation will be employed. Ground-based, 2 micron DWLs have been used to assess the benefits of shot accumulation (approximately SQRT for SNR). Airborne programs like MACAWS have provided good datasets for evaluating various sampling strategies and signal processing algorithms. Using these real data to calibrate our simulation models, we can describe when and how well SPARCLE is expected to preform. Outputs from these performance models will be presented.

Emmitt, G. D.↗
NASA NTRS1974

Entry aerodynamics and heating

An overview of the problems of entry aerodynamics and heating is given with emphasis on survival of the probe, predictability of performance, and reliability of performance. Technological challenges to performance prediction are considered and include: turbulent heat transfer, radiation blockage, chemical state of the shock layer, afterbody heat transfer, asymmetric ablation, and real-gas aerodynamics. It is indicated that various obstacles must be overcome in order to achieve technology readiness. These obstacles are considered to be: extrapolations from ground tests to flight; lack of flight experience; lack of parametric data; and uncertain knowledge of atmospherics.

Olstad, W.↗